identify by their physical port number com ports programmatically

Similar Questions

• WRT160N V2 physical ports seem to be dead... * beep *.

  I got this router installed in my home network for about a year.  The firmware is updated.  Brief description of the home network:

  Comcast Cable Modem

  WRT160N v2

  2 wireless laptops connected to the router

  HP Business Inkjet wireless connected to the router

  1 iMac hard wired (or wireless) to the router

  1 NAS200 hard wired to the router

  1 Epson printer connected to PSUS4 connected to the router

  Sunday night while he was working on the mac, I got a message that I lost the internet connection. I tried powercycling the modem and the router, no change.  I can't connect to the modem (192.168.1.1) of the Mac when connected to the router hard.  If I turn on the wireless on the mac, or use a laptop computer connected wireless, I can connect to 192.168.1.1.  When I do, none of the wired devices appear in the table of network. The Modem is connected to the router, but not connected (DHCP 0.0.0.0) and there is no internet connectivity. If I connect a computer directly to the modem cable, there is a link and it works fine.

  Any troubleshooting I can do, it seems that the physical ports are dead.

  Explanations, or suggestions would be appreciated.

  Justin

  Time to reset the router and reconfigure.  Press and hold the button of reset for 30 seconds and then release.  Wait 30 seconds and now the router power cycle.  Disconnect the modem for now.   Connect to the router via a computer wired to 192.168.1.1 with empty user name, admin password.  Now, reconfigure the router back to your configuration.

• AIP SSM - application of physical port

  Hi all

  I have an ASA5520 with the AIP SSM module.

  I would like to get a quick check on 2 things.

  1. Module AIP-SSM MUST have a physical ethernet port plugged in order for IPS to function?
  2. Module AIP-SSM IP address must be on a different IP range like ASA5520 interfaces. ?

  Please correct me if I'm wrong.

  As I have it a deployment of ASA + AIP, but due to the imitation of physical port on our network & IP; We are not able to answer for the AIP module.

  Please notify.

  1. physical ethernet port must be plugged in and connected to the network for management purposes. To manage the AIP itself module for the GUI of IDM.

  2. No, it didn't need to be on the different range of IP addresses as the interface of the ASA. It's just another IP of your network, and it must be connected to the network via its management port (physical port located on the IAFF himself module), it may be on another subnet within your ASA interfaces.

  The only way that you can manage the AIP via the GUI (IDM) module is via its physical port. However, if you are happy to set up and manage the module AIP via command line, you can always just session through the ASA command line, however, it can be annoying AIP CLI management.

• How to identify a MacBook 2009 serial number?

  How to identify a MacBook 2009 serial number?

  The screen is broken and blue shows only the tasks after the start.

  There are a lot of numbers on the bottom of a MacBook 13 "striped rubber.

  Nothing says serial No.

  I thought to start target disc mode to get info, but the macbook doesn't have a firewire input.

  I have connected a monitor but only get a desk empty with no place to go to.

  I'm used with computer repair, thinking I'll replace it the display. But the owner of the child has no info

  of any kind.

  I would be grateful for your input on how to get the info I need and your thoughts on the display work.

  Thank you for your time and patience.

  There are several ways to find the serial number.

  Click here > How to find the serial number of your MacBook Pro - Apple Support

• Need to identify the designation of port COM through BACK...

  I'm editting a program that sends and receives information to a device via a USB - serial adapter. Previously, the program has been run only on one pc which always use the same COM port when the device is connected. Scripts used with this program have been written to always specify this port. After having taken the device and connected to another pc, the pc allocates another COM port - this is a relatively easy task for me to go through the device management and identify the appropriate COM port, modify the script and get the device communicates with the pc. HOWEVER, in the future, communication must be maintained between the device and a laptop with any user.

  The program you are using may open a windows command prompt and run DOS commands. If possible, I would like to help you find a way to use BACK to identify the COM port used by the USB adapter so I can assign this port number for a variable to be used in scripts, creating their infallible to any user.

  Thanks for your time,

  Chris

  Hello

  To improve assistance to this subject, you can ask your question in the MSDN forums.

  http://social.msdn.Microsoft.com/forums/en-us/categories

• How to assign to the logic of distance in a separate in Logic Pro environment physical port entrance

  Is it possible to assign the logical KEYBOARD with a separate entrance in the port of entry of environmental Logic Pro physics?

  Thank you for your advice.

  I don't think so.  Logic of distance is considered to be a controller. Controller input data stream are made (by logic) before stopping the logic entry in physics. I "think" (I'm not an expert on remote logic) that the flow of midi is available on the port of the sum.

  I'm still not aware that you can change the channel of the South on the logic of distance. So it must be channel a (connected) and your other controllers must be able to have their midi outputs assign other channels if you demux their output.

  (please, correct me if this is not correct about the logic of distance - more conjecture on my part because I use remote logical not)

• My DC-7800 will not identify devices on USB port.

  Slim desktop computer HP Compaq dc7800

   

  I bought an opportunity DC7800 (no disc).  I ran the compatibility of Windows 7 software and it didn't come back with any problems.  I installed Windows 7 Ultimate.  USB does not recognize any jump readers, portable discs or iPod (However when I plug in my external drive Toshiba it powers the drive upwards - just don't install any drivers or shoot them in the directory.)  I installed a printer and it prints well, but even with printing action I can not access the printer on the network (I can access the Public folder shared on the network - so that's good).  After you play with it for several hours, I installed Vista Ultimate on.  He always has exactly the same problem with the USB ports (again... motorized Toshiba but don't even recognize).  I installed all the drivers on the HP site.  Really all that my wife needs him for is the internet and sync his iPhone (it is not recognize it when it is plugged).  Either way, I have no plug in a USB or anything before installing Windows 7.
  

  Ok. If you have Vista Ultimate on...

  See to install the latest chipset driver work.  Install and reboot.

  http://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=20775&keyword=chipset+installation&lang=eng

  Video driver: installation and reboot.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=3459242&prodNameId=3459247&swEnvOID=2098&swLang=13&mode=2&taskId=135&swItem=vc-68809-1

  This driver should install the PCI device.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=3459242&prodNameId=3459247&swEnvOID=2098&swLang=13&mode=2&taskId=135&swItem=vc-78668-1

  It seems that USB devices operate normally (at least with regard to Device Manager is concerned).

  If the USB port still does not work after installing all the drivers above, go back and uninstall these usb controllers and restart.

  If it does not, there is probably some kind of hardware problem that I don't know how to fix.

  Paul

• PowerConnect 5448, how all the trunk of physical ports and allow all the VLAN tags to pass transparently

  I would like to achieve such a goal, do all acts of switch ports 5448 as 'trunk', that is, just as an entry-level switch. Yes, I want all the tags VLAN through seamlessly.

  Let me explain more clearly. If

  • With MAC1 PC1 is connected to switch port 1 (port 1) in short, PC2 with MAC2 is connected to port 2.
  • PC1 sends a packet with vlanid = 30 ethernet VLAN tag,.

  I want the ethernet packet must be SENT to port 2 without modification, i.e. 2 PC will receive the package with exactly the same byte packets that PC1 sends.

  Currently, I want to configure all ports from the switch to act like this, but how to do this? Can someone tell me the more concise CLI commands to achieve? Alternatively, it is possible via the web interface?

  I must again complain the poor manual, which talks about this concept and this notion over and over again (both of ambiguous statements that the author of manual does not), BUT doesn't explain them not at the level of the content of the packages, so I'm totally at a loss.

  I tried the web interface. Simply together port 1 and 2 for access mode or general mode does not work.

  Please help me. Thank you in advance.

  Thank you, Josh, you begin to point me in the right direction.

  Now, I know just affecting a Trunk port, or general mode is NOT sufficient.  I have to give what kind of package VLAN (i.e. what VLAN ID) are allowed to pass through.

  To do this assignment, I have to take 2 steps. say first of all, the database "vlan" to recognize a VLAN ID in the world, then say that some specific port is allowed to pass through with this VLAN ID specific packages.

  Thus, in order to pass packets VLAN with VLAN ID 18-25 no modified (marked packets in packages marked on) g7 to the g8 to port port, I have to do:

  Console # config
  Console (config) # vlan database
  Console(config-VLAN) # vlan 18-25
  Console(config-VLAN) # exit

  Console (config) # interface ethernet g7
  Console # switchport general mode
  Console # switchport General allowed vlan add the tag of 18-25

  and again for the g8. And if I want to 48 ports to act like that, I have to write this kind of order 48 times right? All the shortcuts?

  Some useful links for me: http://hasanmansur.com/2012/10/14/powerconnect-switchport-modes/

• If 2 Airport extreme can stay connected to each other using their LAN ports?

  Hello friends,

  I would like to know if 2 Airport extreme or 1 Airport Extreme and Airport Express can stay connected to each other using LAN ports at the ends? I thought this is the LAN port 1 connected to the WAN port on the 2nd.

  Thank you

  To clarify the issue and the scenario, one of my friend described a typical scenario in which there are 2 AEs. AE1 has an ISP in its port WAN and AE2 has a different ISP in its WAN port. This 2 AE can mutually connected between them by using ports LAN AE1 and AE2 ethernet cable? He said this could be feasible if AE2 remained in bridged mode, without using the ISP attached to its WAN port. I just don't get how this is possible. Friends of the search help.

  Thank you

• iTunes not identify iphone or usb port

  When you install Itunes on a new computer Windows 10, that's not identifies my iPhone.

  I tried the possible sollutions 'all' found on the web, but nothing makes any difference.

  When running the diagnostics on the computer it says that "Apple Mobile Device Driver is missing".

  When you run diagnose on any iPhone and iTunes, it is said that no USB ports has been detected.

  In the written report diagnosis (translated from Swedish):

  iPodService
  12.3.2.35 (x 64) is active.

  iTunesHelper
  12.3.2.35 is active.

  The Apple Mobile Device Service 3.3.0.0 service is active

  No USB chipset was found.
  No chipset FireWire (IEEE 1394) was found

  Found no iPod, iPhone or iPad

  The iPhone is connected by USB-cable and is dected by the computer and visible as a device in Solution Explorer, but not iTunes.

  I have reinstalled iTunes, tried all USB ports, restarted the iPhone, followed the relevant advice on the Apple support.

  I have no free support on me iPhone any longer.

  The thing is that everything is working well on my other computer (Windows 7) with exactly the same version of iTunes.

  Can someone help me why it does not work on my new computer?

  Try the following:

  1. Open Control Panel > Device Manager
  2. Plug in your device
  3. Locate Bus USB Controllers > Apple Mobile Device USB Driver.
     It is also possible that the device may appear under imaging devices, portable devices or other devices or as a device USB of MTB.
  4. Right-click and select software update of the driver...
  5. Click Browse my computer for driver software
  6. Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
     C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers
  7. Click on let me pick from a list of drivers for devices on my computer
  8. Click on Apple Mobile Device USB Driver
  9. Click Next, then close and exit the Device Manager

  Or try If iTunes does not your iPad, iPhone or iPod - Apple Support.

  If not try a complete tear down and rebuild iTunes in accordance with the resolution of the problems with iTunes for Windows updates.

  TT2

• Ethernet/IP - physical port?

  Hey,.

  I have a CVS-1457RT - which has a primary Ethernet port and two Ethernet PoE ports (for cams)

  I need to communicate with a Rockwell RSLogix via Ethernet/IP controller...

  I had the driver Enthernet/IP of NEITHER and is trying to use the example of TagReadWrite.vi...

  How to configure CVS-1457RT use one of the secondary Ethernet ports for this?

  Best regards

  Henrik Ehlert

  Hi Henrik,

  I think that if you connect the primary ethernet port to a network where Rockwell PLC and LabVIEW and PLC PC development are connected to, it should work.

  1. you talk about PLC of RSlogix programming and follow-up

  2. you talk to CVS-1457RT by LabVIEW programming and follow-up. You must deploy your VI to it. In VI, the PLC IP address must be specified for tag reading and writing.

  I don't think that you need to configure one of the secondary Ethernet ports. But in case you do, the jury of the Vision should be a better place to post.

• Control of VISA resource name: to refresh the list of COM ports programmatically

  When the application runs, and you first click this control, it takes 2 to 5 seconds to respond and complete the list for the first time.

  I would like to auto fill in the first time that the application is busy. Can I do this?

  Before allowing the user to click & Select resource VISA name, first use the 'VISA find resource' in your program to do the same thing & then allow or prompt the user to select resources.

  Given that loading EXE, it will execute the FIND VI-first & Labview will inform the resources available.

• How to change HTTP port programmatically?

  Hello
  
  I would like to know if it is possible to change the http port on a server managed by program without repeating the server?
  
  Could it be perhaps with a JMX MBean?
  
  Greetings,
  Améo

  Hi Améo,

  One more thing... As soon as you accelerate that program... Once the server change port, you will get "* PeerGoneException *"... This is because the Server Port is changed... Now the MBeanServerConnection object no longer able to be connected to the old Port. It's good... So when you write try {} catch {} block to handle this exception, and then create a fresh MBeanServerConnection to connect save() and activate().

  Please mark the thread as answered as well... ;) Just for the simplicity of a few users who comes to read messages answered...

  Thank you
  Jay SenSharma

  Published by: Jay SenSharma on February 25, 2010 20:56

• my name or the number comes up when I iMessage someone new?

  don't know what this word, basically need to text someone from my iphone on their iPhone.  My name will automatically appear on their phone or will just my number upwards? They would not already have my number. I think I remember reading somewhere that my name would be launched automatically on any iPhone I text but I could dream it and like his I don't want for the work that they have my full name.

  Thank you to

  No, your number appears unless you have already a contact in their phone with your name and number for their iPhone to replace your number with your name.  You can go to settings < message > Send and Receive and see what number (or email address) is used for new iMessages.  That's what they see, unless they already have a contact card for you.

• Adobe indicates that their own serial number is a fake. Surely a mistake

  Tried to download Premiere Elements by using the serial number recovery system.

  Got an automated message to say that the serial number is incorrect and false!

  Thought I can have mistyped the number and re-tried only for the same thing to happen.

  Surely, there must be a mistake. How can I fix the problem?

  Find the serial number of your Adobe product quickly

  Error "serial number is not valid for this product". Creative Suite

  http://helpx.Adobe.com/Creative-Suite/KB/error-serial-number-valid-product.html