If the IDS 4215 platform support E4 7.0 (2)

Similar Questions

• Troubleshooting of the IDS 4215 interface detection

  Hello!

  I am deploying IDS4215 with interface of remote sensing (Fa0/1) connected to the SPAN Cat3750 Gig1/0/1 interface.

  The problem is the following. The ID works for a while (I am able to view alerts and States 'show int' Fa0/1 located upward). Then after awhile Fa0/1 goes down, I don't know why.

  The Cat3750 shows that State of Gig1/0/1 passes the "follow-up" to "notconnect. All I can do is restart IDS.

  Catalyst shows no error on the interface.

  I am a novice in ID, and I appreciate any idea where to start troubleshooting.

  Thanks in advance!

  SSM

  Catalyst settings:

  GigabitEthernet1/0/1 interface

  Span ID description

  full duplex

  Speed 100

  end

  control interface of the session 1 source article gi1/0/27 - 28

  control interface of the session 1 source Gi2/0/27 - 28

  control interface of destination session 1 item in gi1/0/1

  Config of IDS:

  ! ------------------------------

  ! Version 5.1 (1)

  ! Current configuration changed the game 22 dec 10:11:22 2005

  ! ------------------------------

  service interface

  Physics-interface FastEthernet0/0

  automatic duplex

  automatic speed

  output

  Physics-interface FastEthernet0/1

  FE0/1 description

  Admin-state enabled

  full duplex

  Speed 100

  output

  output

  ! ------------------------------

  service-analysis engine

  vs0 virtual sensor

  Physics-interface FastEthernet0/1

  output

  output

  In my view, that there is something seriously wrong with version 5.1 (1). Why Cisco continues to allow users to download is beyond comprehension. I will be rebuild about 20 sensors today because of this problem. I have rebuilt 6 sensors Friday [from an ISO image, models 4235,4240,4255] and let them run this weekend. 5 out of 6 have the sensor interface down once again.

• Cisco IDS 4215 signatures update

  Hello people,
  We have a few Cisco IDS 4215 and would like to know if the upgrade of signatures, we can remove those released previously or whether precedents should not be eliminated.

  Information system of these devices.

  ***

  TAC-contact information
  URL: http://www.cisco.com/public/support/tac/home.shtml/
  Phone: 1 (800) 553-2447

  Sensor time is 110 days.
  Platform: IDS-4215-4FE-K9
  Boot partition: application

  Partition: application
  Build version: 6.0 (6) E3
  Host:
  Domain keys key1.0
  Definition of signature:
  Update of the signature S439.0 2009-09-30
  Virus update V1.4 2007-03-02
  OS version: 2.4.30 - IDS-smp-bigphys
  Applications
  MainApp
  N NUBRA_2009_JUL_15_01_10_6_0_5_57 2009-07-15 T 01: 15:08 - 0500 ipsbuild
  The executing State: running
  AnalysisEngine
  N NUBRA_2009_JUL_15_01_10_6_0_5_57 2009-07-15 T 01: 15:08 - 0500 ipsbuild
  The executing State: running
  Updates installed
  Update name: IPS - K9 - 6.0 - 6 - E3
  Once installed: July 15, 2009 18.48.06
  Update name: IPS-GIS-S439-req - E3.pkg
  Installed time: 6 October 2009 13.07.55
  Next lower upgrade:
  Partition: recovery
  Build version: 1.1 - 6, 0000 E3

  PEP Udi chassis
  Description sensor unit IPS 4215
  PID ID-4215-4FE-K9
  vid V01
  SN 88808513168

  Memory usage
  usedBytes = 377655296
  freeBytes = 132685824
  totalBytes = 510341120

  Use of the disk
  the application data uses 33.2 M off 166,8 M bytes of disk space available (21% of use)
  start using 37.6 M off 68.6 M bytes of disk space available (58% of use)
  Application log using 529,5 M off bytes of 2.8 G of disk space available (20% of use)

  ***

  Many thanks in advance,

  Luca

  Luca;

  Signature updates are cumulative, so you can simply ask the S493 update.  A caveat, however, if you need to make a big move in the signature release (say S470 to S493) it is usually more effective to make small updates (especially on a platform of low memory as the IDS-4215).

  Scott

• How to see the log files in IDS 4215

  Hi all

  I have an IDS 4215, I want to check the Logs of the system for this ID, as Interface something like that.

  Thanks in advance.

  All system messages, including signature events are all 'show' commands.

  Enter the command show event displays only events in real time. If you want ot, past events, you need to add a time to the command option; show events past 20:00

  -Bob

• Doubts on the leaves of the platform supported between Tuxedo 12 c and OTMQ

  Tuxedo team, Hi!

  I was looking at the leaves of the platform supported on Tuxedo and OTMQ and I'm having a doubt as some point. In Tuxedo 12 platform leaves, it is said that RH Enterprise Linux is supported up to version 6.3, as indicated on the link below:

  http://docs.Oracle.com/CD/E35855_01/Tuxedo/docs12c/install/inspds.html#wp1476309

  Regarding the OTMQ, I expect the same platform supported, but discovered that it only supports RH Linux at 5.6, as indicated on the link below:

  http://docs.Oracle.com/CD/E35855_01/otmq/docs12c/install/inspds.html

  Is this good? What are the limits of the OTMQ on a RH 6.x?

  Thank you

  brunno Attorre

  Hi Bruno.

  OTMQ 12 c is currently supported by HR 5.6. There has been discussions of the approval process on later versions of RH Linux.  Please contact Oracle support to save your application and let us know what version of Linux RH you are interested.  Thank you

  Deepak Goel

  Oracle Tuxedo product management

• IDS 4215, good place for an interface sniff (LAN or DMZ)

  I have this sensor with two interfaces only at work, I was asked to check that

  See the IDSWORK version #.

  Application partition:

  The Cisco Systems Version 1.0000 S47 Intrusion detection sensor

  2.4.18 - 5smpbigphys-4215 OS version

  Platform: IDS-4215

  an interface that is Ethernet 0 connected to switch in the DMZ, and 1 Ethernet connected to switch 4005, logically I have to monitor DMZ not switch box 4005 (since I had only two interfaces, my case), I'm right?

  That means that ethernet 0 should be to sniff (surveillance) since it is connected to the DMZ and interface 1 for command and control, since it is connected to switch 4005, but according to cisco specifications

  http://Cisco.com/en/us/products/HW/vpndevc/PS4077/products_configuration_guide_chapter09186a008055df7d.html#wp1051279

  Table 5-2

  FastEthernet0/0: Interfaces supporting VLAN pairs Inline (port detection)

  FastEthernet0/1: Interfaces do not support Inline (command and control Port)

  Note: Cisco has mentioned FastEthernet, one I had Ethernet, makes all the difference?

  Because I did not have this configuration, he made by another, should I change this?

  It seems that your credentials are equipped with the basic ports (2 x Ethernet) with E0 C & C port, while E1 is followed by port.

  BTW, Ethernet/FastEthernet ports are in fact the same.

  To monitor your DMZ segment, then place the E1 in this segment, as E0 on inside segment where in addition to directing the Manager of its web management or CLI interface box, you probably can use basic VMS that comes free with it.

  And since you have dedicated switch to host the entire DMZ segment, you can easily monitor box (SPAN) all and send all traffic to the IDS.

  If you need to change the configuration, you may need to test at least to verify signatures is enabled/disabled and pc/mgt host is allowed to access the box and so on. But it is a good practice for audit and review the new config/setup, as it is a security zone, you need to do to monitor trust and you talk about all the possible threats, attacks or violations.

  HTH

  AK

• Questions of IDS-4215

  I bought this unit and I have problems with it, I did the restore and I put the new password and pick-me-up Dungeon to it, how to make out of it?

  CISCO SYSTEMS IDS-4215
  Embedded BIOS Version 5.1.7 03/02/04 11:20:35.01
  Compiled by dnshep
  Evaluate the Options of execution...
  Check for disc Image valid
  GRUB, loading stage1.5.

  GRUB loading, please wait...

  GRUB version 0.91 (632K lower / higher than 523264K memory)

  -------------------------------------------------------------------
  0: cisco IDS (vmlinuz - 2.4.26 - IDS-smp-bigphys}
  1: cisco IDS recovery
  -------------------------------------------------------------------

  Use the ^ and v keys to select which input is highlighted.
  Press ENTER to start the operating system selected, 'e' to change the
  orders before starting, 'a' to change the kernel arguments
  before you start, or 'c' for a command line.

  Entry 0 will be started automatically in 1 seconds.
  Start ' Cisco IDS (vmlinuz - 2.4.26 - IDS-smp-bigphys} ")

  root (hd0, 0)
  Filesystem type is ext2fs, partition type 0 x 83
  kernel (hd0,0)/boot/vmlinuz-2.4.26-IDS-smp-bigphys ro root = / dev/hdb1 had = flash)
  Console = ttyS0 bigphysarea = 16384
  [Linux bzImage, setup = 0 x 1400, size = 0x11b282]

  Linux version 2.4.26 - IDS-smp-bigphys ([email protected] / * / _build_master) (version gcc 2.96 20000731 (Red Hat Linux 7.3 2, 96-112)) #2 SMP Thu Aug 18 11:03:13 CDT 2005
  BIOS fitness card RAM:
  BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
  BIOS-e820: 000000000009e000 - 00000000000a 0000 (reserved)
  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
  BIOS-e820: 0000000000100000-0000000020000000 (usable)
  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
  0 MB HIGHMEM available.
  512 MB LOWMEM available.
  On the node 0 totalpages: 131072
  area (0): 4096 pages.
  area (1): 126976 pages.
  area (2): 0 pages.
  DMI does not exist.
  ACPI: Unable to locate the PDSP
  Kernel command line: ro root = / dev/hdb1 had flash = console = ttyS0 bigphysarea = 16384
  ide_setup: a = flash
  Local APIC disabled by BIOS - reactivation.
  Local APIC found and activated!
  The initialization of the #0 CPU
  Detected 845,655 MHz processor.
  Console: the unit dummy color 80 x 25
  Calibrating delay loop... 1684.27 BogoMIPS
  Memory: 449240 k/524288 KB available (kernel code of 1621 k, k 74656 reserved, 639 k data, 136 k init, 0 k highmem)
  Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
  Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
  Get cache hash table entries: 512 (order: 0, 4096 bytes)
  Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
  The page cache hash table entries: 131072 (order: 7, 524288 bytes)
  CPU: L1 I cache: 16K, D L1 cache: 16K
  CPU: L2 cache: 128K
  Architecture Intel machine control supported.
  Intel machine check reporting enabled on CPU #0.
  Enabling fast FPU save and restore... done.
  Allowing the use of unmasked SIMD FPU exception... done.
  Checking 'hlt' instruction... Ok.
  UNIFIX POSIX compliance test
  MTRR: v1.40 (20010327) Richard Gooch ([email protected] / * /)
  MTRR: detected mtrr type: Intel
  CPU: L1 I cache: 16K, D L1 cache: 16K
  CPU: L2 cache: 128K
  Intel machine check reporting enabled on CPU #0.
  CPU0: Intel Celeron (Coppermine) stepping 0
  by timeslice cut CPU: 365,62 usecs.
  Motherboard undetected SMP.
  Turned off turned on CPU #0
  Value of ESR before activating the vector: 00000000
  Value of ESR after activating the vector: 00000000
  Local APIC interrupt using timer.
  calibration of APIC timer...
  ..... CPU clock speed is 845,6568 MHz.
  ... bus clock speed host is 99,4889 MHz.
  CPU: 0, clocks: 994889, slice: 497444
  CPU0
  Waiting on wait_init_idle (card = 0x0)
  All processors have been init_idle
  PCI: PCI BIOS revision 2.10 to 0xff6a9, last bus = 1 entry
  PCI: Using configuration type 1
  PCI: Hardware probing PCI
  PCI: Hardware probing PCI (bus 00)
  Limitation of direct transfers of PCI/PCI.
  ISAPNP: digitization of the PnP cards...
  ISAPNP: no Plug Play devices & found
  Linux NET4.0 for Linux 2.4
  Swansea University Computer Society NET3.039-based
  The initialization of the RT netlink sockets
  From kswapd
  bigphysarea: 16384 pages for 0xc1606000.
  Responsible journaled block device driver
  Pty: 2048 Unix98 ptys configured
  keyboard: there is no Timeout - at THE keyboard? (ed)
  keyboard: there is no Timeout - at THE keyboard? (f4)
  Series c 5.05 driver version (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI active ISAPNP
  ttyS00 at 0x03f8 (irq = 4) is a 16550
  ttyS01 at 0x02f8 (irq = 3) is a 16550
  V1.10F real time clock driver
  Initialized RAM disk driver: 16 discs RAM 4096 K size 1024 blocksize
  loop: loaded (max 8 devices)
  LPC: version 0.1 (August 18, 2005)
  Uniform cross-platform E-IDE review pilot: 7.00beta4 - 2.4
  IDE: assuming that the speed of the bus system 33 MHz for modes PIO; Override with idebus = xx
  PIIX4: Controller IDE PCI slot 00:07.1
  PIIX4: chipset revision 1
  PIIX4: not 100% natively: will probe IRQS later
  ide0: BM - DMA at 0xf800-0xf807, BIOS settings: had: pio, hdb:pio
  IDE1: BM - DMA at 0xf808-0xf80f, the BIOS settings: hdc:pio, hdd:pio
  has: SanDisk SDCFB-256, CFA HDD
  HDB: IC25N020ATCS04-0, ATA drive
  has: disable DMA (U) to SanDisk SDCFB-256
  BLK: queue c03bf1a8, I/O limit 4095 MB (mask 0xffffffff)
  ide0 at 0x1f0-0x1f7, 0x3f6 on irq 14
  has: attachment the ide disk driver.
  had: task_no_data_intr: status = 0 x 51 {DriveReady SeekComplete error}
  had: task_no_data_intr: error = 0 x 04 {DriveStatusError}
  had: 501760 sectors (257 MB) w/1KiB Cache, CHS = 497/16/63
  HDB: attached the ide disk driver.
  HDB: host protected area-online 1
  HDB: 39070080 sectors (20004 MB) w/1768KiB Cache, CHS = 2432/255/63, UDMA (33)
  Check the partition:
  has: hda1, hda2, hda3
  HDB: hdb1, hdb2 hdb3 hdb4
  IDE: late registration of the driver.
  Review SCSI subsystem driver: 1.00
  I2C-core. o: i2c core module version 2.8.7 (20040611)
  I2C - dev. o: i2c/dev entries driver module version 2.8.7 (20040611)
  I2C - proc.o version 2.8.7 (20040611)
  I2C-i801 version 2.8.7 (20040611)
  Net4: Linux 1.0 for NET4.0 TCP/IP
  IP protocols: ICMP, UDP, TCP, IGMP
  IP: routing 4096 buckets cache hash table, 32Kbytes
  TCP: Hash tables configured established 131072 bind (65536)
  Linux IP router multicast 0.06 and PIM - SM
  Net4: Unix domain sockets 1.0/SMP for Linux NET4.0.
  kjournald starting.  Commit interval 5 seconds
  Ext3-fs: mounted filesystem with ordered data mode.
  VFS: Mounted root (ext3 file system) readonly.
  Release of memory used kernel: 136 k released
  INIT: initialization of version 2.84
  Welcome to CIDS v4.1 (1) S47 (Phoenix)
  Mounting proc filesystem: [OK]
  Configuration of the kernel parameters: [OK]
  Setting clock (localtime): my Apr 19 19:14:53 UTC 2010 [OK]
  Activation of swap partitions: [OK]
  Hostname parameter sensor: [OK]
  modprobe: can't open dependencies file /lib/modules/2.4.26-IDS-smp-bigphys/modules.dep (no such file or directory)
  Checking file system root
  / dev/hdb1: clean, 27334/83520 files, 56775/166666 blocks
  [/sbin/fsck.ext3 (1)-/] fsck.ext3 - a/dev/hdb1
  [OK]
  Back the root read / write file system: [OK]
  Find the module dependencies: depmod: can't open /lib/modules/2.4.26-IDS-smp-bigphys/modules.dep for writing
  [NOT]
  Checking of file systems
  / dev/hdb3: clean, 12 files, 2008, 1300/8032 blocks
  / dev/hda1: clean, 33/2656 files, blocks of 4184/10584
  / dev/hdb4: clean, 32/2280320 files, blocks 80505/4558443
  / dev/hda3: clean, 20/58232 files, 84949/232848 blocks
  Check all file systems.
  [/sbin/fsck.ext3 (1)-/ bootmnt] fsck.ext3 - a/dev/hda1
  [/sbin/fsck.ext3 (2)-/ usr/cids/idsRoot/shared] fsck.ext3 - a/dev/hdb3
  [/sbin/fsck.ext3 (2)-/ usr/cids/idsRoot/var] fsck.ext3 - a/dev/hdb4
  [/sbin/fsck.ext3 (2)-/ mnt/recovery] fsck.ext3 - a/dev/hda3
  [OK]
  Mounting local filesystems: [OK]
  Activation of local file system quotas: [OK]
  Activation of the swap space: [OK]
  Non-interactive startup entry
  Setting the network parameters: [OK]
  Set up the loopback interface: [OK]
  modprobe: can't open dependencies file /lib/modules/2.4.26-IDS-smp-bigphys/modules.dep (no such file or directory)
  Setting up interface eth1: [OK]
  Start recorder system: [OK]
  Kernel start recorder: [OK]
  Load keymap: [OK]
  Loading system font: [OK]
  The initialization of the random number generator: [OK]
  Audit of the allocated kernel memory: [OK]
  No XL map shows
  Charge Cidmodcap: WARNING: the kernel-module version mismatch
  /lib/modules/CID/cidmodcap.o was compiled for kernel version 2.4.18 - 5smpbigphys
  While this kernel version 2.4.26 - IDS-smp-bigphys
  /lib/modules/CID/cidmodcap.o: symbol register_chrdev_Rsmp_0450333d pending
  /lib/modules/CID/cidmodcap.o:
  Tip: You are trying to load a module without a GPL compatible license
  and unresolved symbols.  Contact the provider module for
  help, only they can help you.

  [NOT]
  Creation of boot.info [OK]
  Checking for changes to the system since the last boot [WARNING]
  Check the identification of the model [OK]
  Model: IDS-4215
  Error: mainApp has not started
  From sshd: [OK]
  From xinetd: [OK]
  From crond: [OK]
  From anacron: [OK]

  Login: cisco
  Password:
  You are required to change your password immediately (years)
  Change password for cisco
  (ongoing) UNIX password:
  New password:
  Retype the new password:
  NOTICE *.
  This product contains cryptographic features and is under the United States
  and local laws governing the import, export, transfer and use. Delivery
  Cisco cryptographic products does not imply permission to third parties to import,
  export, distribute or use encryption. Importers, exporters, distributors and
  users
  sensor connection: cisco
  Password:
  NOTICE *.
  This product contains cryptographic features and is under the United States
  and local laws governing the import, export, transfer and use. Delivery
  Cisco cryptographic products does not imply permission to third parties to import,
  export, distribute or use encryption. Importers, exporters, distributors and
  users are responsible for compliance with U.S. and local country. With the help of
  This product you agree to comply with the regulations and laws in force. If you
  are unable to meet the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:
  http://www.Cisco.com/WWL/export/crypto

  If you need assistance please contact us by mail at
  [email protected] / * /.

  connection of the sensor:

  Since you did the recovery I assumeyou already tried to the unit powering down and back up.

  This is a weird problem I havn't seen before, but sometimes the sensors get currupt and need a full reimage to return to normal.

  I would like to download the most recent image 4215 and TFTP in your sensor in ROMMON.

  http://www.Cisco.com/en/us/partner/docs/security/IPS/6.0/installation/guide/hwImage.html#wp1030874

  -Bob

• IDS-4215 virtual sensors

  Can I have several virtual devices on 4215 executes code 6.0?

  Unfortunately, IDS-4215 does not support many virtual devices.

  Here is the URL for your reference:

  http://www.Cisco.com/en/us/docs/security/IPS/6.0/Configuration/Guide/IDM/dmAnEng.html#wp1035318

• the pure networks platform service is not running

  I can't use my wireless card no matter what and this message

  You (or did you) a version of Network Magic installed?  Generally, the complete message would be:

  The Pure Networks Platform Service is not running
  Pure Networks Platform Service must run in order for Network Magic to function. If you have manually stopped or disabled the Pure Network Platform service, restart now.
  [2 links]

  See this FAQ: http://www.purenetworks.com/support/faq/195.html (the site can be slow to load)

  The Microsoft Windows Installer Cleanup utility is no longer available from Microsoft, apparently because it sometimes more removed he was supposed to.  You can always get it, however, here: http://majorgeeks.com/Windows_Installer_CleanUp_Utility_d4459.html

  If you use the Windows Installer Cleanup utility, make a first Restore Point (or back up the registry with C:\windows\erunt).

  If you feel uncomfortable using CIP, download and use For free Revo Uninstaller to uninstall the same applications listed in the FAQ

  Personally, I'd skip step 3 "download Network Magic."  There is really no need for this application and, as you saw, it can cause problems.

• License on Cisco IDS 4215 box

  I have IDS 4215 (version 4) works fine for 2 years. All of a sudden I could not access the IDS4215 via the console or telnet last month. I rebooted it, but there is no change.

  Then we get the ROMMON prompt via CTRL-R. We performed procedures "Installation image of the system IDS-4215. We have installed version 5. So, we lost the old license for IDS 4215 ver 4. How can I get old license?

  We want to make the 4215 IDS to work with version 5 and the latest signatures. What should we do in this regard?

  It wasn't a license file in ver 4.

  Licenses were introduced in ver 5.

  Licenses are included as part of your Cisco Service for IPS maintenance contract.

  To see if you have a contract to day just go in the license of IDM configuration page and click on the button to say IDM to check cisco.com for a license.

  If she comes back with a license while your contract is up to date and everything is good.

  If she does not return with a license, then probably you don't have a Service Cisco IPS service contract for your sensor.

  Your Cisco or an authorized Cisco reseller sales Reprentative contract and request a quote for Service Cisco IPS contract for your sensor.

  Don't forget to give them the serial number of your sensor when you buy the contract so it is followed correctly in the database of contract of Cisco.

• Error on server IDS 4215 TLS certificate VEI

  IDS 4215 5.0 software version not connect with IVE and IME server. "" IOException when trying to get the certificate: java.security.cert.CertificateExpiredException. error message is displayed. How this can be solved?

  Hello

  I think it's easy, please go to the CLI and try the following?

  generate TLS keys

  Let me know the results!

  http://www.Cisco.com/en/us/docs/security/IPS/6.0/Configuration/Guide/CLI/cliTasks.html#wp1036929

  Mike

• IDS 4215 date and time change after restart

  Hello

  I am facing problem with cisco IDS 4215 (version 6.0), date and time of change in the device after reboot. What is the command to save the configuration. record or write mem does not work.

  Amarjeet Singh

  Once the date and time changes are applied Cisco IPS CLI, they should have been saved. No additional step of "savings" manually is necessary.

  Also, have you thought about Configure NTP on IPS server. IPS synchronizes time with NTP server, if there is no difference.

  I suggest you contact Cisco TAC and report the problem of equipment.

  Kind regards

  Sawan Gupta

• How to accompany the IDS in ASA 5505 and 5520?

  Dear All;

  We have the following configuration of HW for the ASA 5505 and ASA 5520, we add the functionality of system of detection of Intrusion (IDS) to the two ASA. My question is: what are the modules required to support this function, and what is the deference between IPS and IDS, fact the same Module both the feature?

  Part number:	Description	QTY.
  ASA5505-BUN-K9	ASA 5505 appliance with SW 10 users, 8 ports, 3DES/AES	1
  CON-SNT-AS5BUNK9	SMARTNET 8X5XNBD ASA5505-BUN-K9	1
  SF-ASA5505 - 8.2 - K8	ASA 5505 Series Software v8.2	1
  CAB-AC-C5	Power supply cord Type C5 U.S.	1
  ASA5500-BA-K9	ASA 5500 license (3DES/AES) encryption	1
  ASA5505-PWR-AC	ASA 5505 power adapter	1
  ASA5505-SW-10	ASA 5505 10 user software license	1
  SSC-WHITE	ASA 5505 hood SSC of the location empty	1
  ASA-ANYCONN-CSD-K9	ASA 5500 AnyConnect Client + Cisco Security Office software	1

  Part number:	Description	QTY.
  ASA5520-BUN-K9	ASA 5520 appliance with SW HA, 4GE + 1FE, 3DES/AES	2
  CON-SNT-AS2BUNK9	SMARTNET 8X5XNBD ASA5520 w/300 VPN Prs 4GE + 1FE3DES/AES	2
  ASA5520-VPN-PL	ASA 5520 VPN over 750 IPsec User License (7.0 only)	2
  ASA-VPN-CLNT-K9	Cisco VPN Client (Windows Solaris Linux Mac) software	2
  SF - ASA - 8.2 - K8	ASA 5500 Series Software v8.2	2
  CAB - ACU	Power supply cord (UK) C13 BS 1363 2.5 m	2
  ASA-180W-PWR-AC	Power supply ASA 180W	2
  ASA5500-BA-K9	ASA 5500 license (3DES/AES) encryption	2
  ASA-ANYCONN-CSD-K9	ASA 5500 AnyConnect Client + Cisco Security Office software	2
  SSM-WHITE	ASA/IPS SSM hood of the location	2

  Thanks in advance.

  Rashed Ward.

  Okay, I was not quite correct in my first post.

  These modules - modules only available for corresponding models of ASA.

  They all can act as IPS (inline mode) or IDS ("Promiscuous" mode), depending on how you configure your policies.

  When acting as IPS, ASA redirects all traffic through the module, then all the traffic is inspected and can be dropped inline if a signature is triggered.

  When she acts as an ID, ASA a few exemplary traffic is the module for inspection, but the actual traffic is not affected by the module, as it's not inline in this case.

  In addition, these modules can be both comdination. That is part of the traffic can be inspected "inline", when some other (more sensitive) traffic can be inspected in promiscuous mode.

  To better understand, familiarize themselves with this link:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/modules_ips.html

• Sensor not known version of the IDS MC

  The system IDS 4215 sensor is version: 1.0000 S47. The MC of the IDS (version 1.2) does not have this version and recommends an update of the signature.

  I downloaded the file IDS-K9-min-4.1-1-S47.rpm.pkg to the web site of Cisco and attempt to update the signature in accordance with the instructions in the ReadMe file.

  I received the following message:

  "Failed to update the object. The provided update package seems to be corrupted, or refused permission to read the file. Please check the contents of the update package and try the operation again. »

  I checked the downloaded file's MD5 signature, and it's OK. I tried to download the file again and I got truncated versions (size about 256 KB).

  I use the correct file? How can I get the correct version of the file? Am I missing any parameter?

  Thank you for your help.

  What you have is the package of real update to the sensor itself. If you use MC to push updates, you need the package from the following location:

  http://www.cisco.com/cgi-bin/Software/Tablebuild/doftp.pl?ftpfile=cisco/crypto/3DES/cw2000/mgmt-ctr/ids/ids4updates/IDS-K9-min-4.1-1-S47.zip&swtype=FCS&software_products_url=%2Fcgi-bin%2Ftablebuild.pl%2Fmgmt-ctr-ids-ids4updates&isChild=&appName=&tbtype=mgmt-ctr-ids-ids4updates

  It contains the files needed for the update of MC and the real update package will be pushed to the sensor.

• RHEL 7 will never be a platform support for vSphere SDK for Perl 5.5?

  RHEL 7 will never be a platform support for vSphere SDK for Perl 5.5?

  https://www.VMware.com/support/developer/viperltoolkit/viperl55/vsp55_vsperl_relnotes.html#supported

  
  

  Thank you
  

  We have recently updated the Perl SDK to 6.0 U2 which now supports RHEL 7.1, as seen in the vSphere SDK for Perl Release Notes