IKEv2 vpn dynamic sites

Similar Questions

• ASA (v9.1) VPN from Site to Site with IKEv2 and certificates CEP/NDE MS

  Hi all

  I am currently a problem with VPN Site to Site with IKEv2 and certifiactes as an authentication method.

  Here is the configuration:

  We have three locations with an any to any layer 2 connection. I created each ASA (ASA5510 worm 9.1) to establish one VPN of Site connection to the other for the other two places. Setting this up with pre shared keys and certificates that are signed by the CA MS administrator manually work correctly.

  But when we try to enroll these certificates through the Protocol, CEP/NDE his does not work.

  Here are my steps:

  1 configure the CA Turstpoint to apply to the certification authority

  2. request that the CA through the SCEP protocol works fine

  3. set up a Trustpoint and a pair of keys for the S2S - VPN connection

  4. registration form identity certificate CA via the SCEP Protocol with a one time password works fine

  5. set the trustpoint created as for the S2S - VPN IKEv2 authentication method.

  Now I did it also for the other site of the VPN Tunnel. But when I ping on a host that is on a different location to make appear the Tunnel VPN - the VPN session is not established. In the debugs I see that there are a few problems during authentication of the remote peer.

  On the MS that I see that the certifactes of identity for both ASAs are communicated and not revoked or pending state. The certificate based on the model of the "IPSec (Offline).

  When the CA-Admin and a certificate me manually based on a copy of the model of "Domaincontroller" connection is successfully established.

  So I would like to know which is the correct certificate for IP-Sec peers template to use for the Protocol, CEP and MS Enterprise CA (its server 2008R2 of Microsoft Enterprise)?

  Anyone done this before?

  ASA requires that the local and Remote certificate contains EKU IP Security Tunnel Endpoint (1.3.6.1.5.5.7.3.6) (aka IP Security Tunnel termination). You can create a Microsoft CA model to add.

  If you absolutely must go with the 'bad' cert, there is a command

  ignore-ipsec-keyusage

  but it is obsolete and not recommended.

  Meanwhile at the IETF:

  RFC 4809

  3.1.6.3 extended Key use

  Extended Key Usage (EKU) indications are not required.  The presence
  or lack of an EKU MUST NOT cause an implementation to fail an IKE
  connection.
  

• NAT-XLATE-FAILURE on the VPN from Site to site connection.

  I had configured a VPN of Site to new site on my network, once I created Tunnel appears, but there is no traffic when I made trace packet its gave me error "(NAT-XLATE-FAILED), NAT has failed."

  Here is the configuration runing.

  ASA 9.1 Version 2
  !
  ciscoasa hostname
  activate 2KFQnbNIdI.2KYOU encrypted password
  names of
  IP local pool kecdr 10.100.1.1 - 10.100.1.50 mask 255.255.255.0
  local pool KECVPN 10.2.1.200 - 10.2.1.225 255.255.255.0 IP mask
  !
  interface GigabitEthernet0/0
  nameif outside
  security-level 0
  IP 168.187.199.66 255.255.255.252
  !
  interface GigabitEthernet0/1
  nameif inside
  security-level 100
  10.2.1.1 IP address 255.255.255.0
  !
  interface GigabitEthernet0/2
  nameif DMZ
  security-level 50
  IP 10.60.1.2 255.255.255.0
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  passive FTP mode
  DNS domain-lookup outside
  DNS lookup field inside
  management of the DNS domain-lookup service
  DNS server-group DefaultDNS
  Name-Server 8.8.8.8
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_10.100.1.0_26 object
  255.255.255.192 subnet 10.100.1.0
  network of the NETWORK_OBJ_10.2.1.192_26 object
  255.255.255.192 subnet 10.2.1.192
  network of the NETWORK_OBJ_10.13.0.0 object
  Home 10.13.0.0
  network of the NETWORK_OBJ_10.2.0.0 object
  host 10.2.0.0
  network of the NETWORK_OBJ_10.3.0.0 object
  Home 10.3.0.0
  the DM_INLINE_NETWORK_1 object-group network
  host object-network 10.2.0.0
  object-network 10.60.1.0 255.255.255.0
  inside_access_in list extended access permitted ip any4 any4
  inside_access_in list of allowed ip extended access all 10.60.1.0 255.255.255.0
  outside_access_in list extended access permitted ip any4 any4
  allow global_access to access extensive ip list a whole
  DMZ_access_in of access allowed any ip an extended list
  DMZ_access_in list extended access permit ip any interface inside
  outside_cryptomap list extended access allowed host ip DM_INLINE_NETWORK_1 10.3.0.0 object-group
  permit access ip host 10.2.0.0 extended list outside_cryptomap_1 10.11.0.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  management of MTU 1500
  MTU 1500 DMZ
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow any response echo inside
  ICMP allow any echo inside
  ICMP allow all DMZ
  ICMP allow any echo DMZ
  ICMP allow any response to echo DMZ
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.2.1.192_26 NETWORK_OBJ_10.2.1.192_26 non-proxy-arp-search to itinerary
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.100.1.0_26 NETWORK_OBJ_10.100.1.0_26 non-proxy-arp-search to itinerary
  NAT (inside DMZ) static source a whole
  NAT (inside, outside) static source NETWORK_OBJ_10.2.0.0 NETWORK_OBJ_10.2.0.0 NETWORK_OBJ_10.13.0.0 NETWORK_OBJ_10.13.0.0 non-proxy-arp-search of route static destination
  NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_10.3.0.0 NETWORK_OBJ_10.3.0.0 non-proxy-arp-search of route static destination
  !
  NAT source auto after (indoor, outdoor) dynamic one interface
  Access-group outside_access_in in interface outside
  inside_access_in access to the interface inside group
  Access-group DMZ_access_in in DMZ interface
  Access-Group global global_access
  Route outside 0.0.0.0 0.0.0.0 168.187.199.65 1
  Route DMZ 10.1.0.0 255.255.0.0 10.60.1.1 1
  Route DMZ 10.2.0.0 255.255.0.0 10.60.1.1 1
  Route DMZ 10.60.0.0 255.255.0.0 10.60.1.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  AAA authentication LOCAL telnet console
  the ssh LOCAL console AAA authentication
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 10.0.0.0 255.0.0.0 inside
  http 0.0.0.0 0.0.0.0 outdoors
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto outside_map 1 match address outside_cryptomap
  card crypto outside_map 1 set pfs Group1
  peer set card crypto outside_map 1 196.219.202.197
  card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto outside_map 2 match address outside_cryptomap_1
  peer set card crypto outside_map 2 185.52.118.67
  card crypto outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  Crypto ca trustpoint _SmartCallHome_ServerCA
  Configure CRL
  trustpool crypto ca policy
  Crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
  30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
  496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
  74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
  68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
  302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
  63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
  010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
  02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
  6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
  c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
  69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
  1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
  445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
  6c2527b9 deb78458 c61f381e a4c4cb66
  quit smoking
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 allow outside
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  authentication crack
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 20
  authentication rsa - sig
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 40
  authentication crack
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 50
  authentication rsa - sig
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 60
  preshared authentication
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 70
  authentication crack
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 80
  authentication rsa - sig
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 90
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 100
  authentication crack
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 110
  authentication rsa - sig
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 130
  authentication crack
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 140
  authentication rsa - sig
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 150
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  Telnet 0.0.0.0 0.0.0.0 outdoors
  Telnet 10.0.0.0 255.0.0.0 inside
  Telnet 10.2.0.0 255.255.0.0 inside
  Telnet 10.1.0.0 255.255.0.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH 10.0.0.0 255.0.0.0 inside
  SSH 10.2.0.0 255.255.0.0 inside
  SSH 10.1.0.0 255.255.0.0 inside
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  statistical threat detection port
  Statistical threat detection Protocol
  Statistics-list of access threat detection
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  internal GroupPolicy_185.52.118.67 group strategy
  attributes of Group Policy GroupPolicy_185.52.118.67
  Ikev1 VPN-tunnel-Protocol
  internal GroupPolicy_196.219.202.197 group strategy
  attributes of Group Policy GroupPolicy_196.219.202.197
  Ikev1 VPN-tunnel-Protocol
  internal kecdr group policy
  attributes of the strategy of group kecdr
  value of server DNS 8.8.8.8
  Ikev1 VPN-tunnel-Protocol
  internal KECCISCO group policy
  KECCISCO group policy attributes
  value of server DNS 8.8.8.8
  Ikev1 VPN-tunnel-Protocol
  internal KECVPN group policy
  KECVPN group policy attributes
  value of server DNS 8.8.8.8
  Ikev1 VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  username, password admin eY/fQXw7Ure8Qrz7 encrypted privilege 15
  cisco 3USUcOPFUiMCO4Jk encrypted password username
  username privilege 15 encrypted password 3ofqMXhysxFRHhoQ keccisco
  type tunnel-group kecdr remote access
  tunnel-group kecdr General-attributes
  address kecdr pool
  Group Policy - by default-kecdr
  kecdr group of tunnel ipsec-attributes
  IKEv1 pre-shared-key *.
  type tunnel-group KECVPN remote access
  attributes global-tunnel-group KECVPN
  address kecdr pool
  Group Policy - by default-KECVPN
  IPSec-attributes tunnel-group KECVPN
  IKEv1 pre-shared-key *.
  type tunnel-group KECCISCO remote access
  attributes global-tunnel-group KECCISCO
  address KECVPN pool
  Group Policy - by default-KECCISCO
  IPSec-attributes tunnel-group KECCISCO
  IKEv1 pre-shared-key *.
  tunnel-group 196.219.202.197 type ipsec-l2l
  tunnel-group 196.219.202.197 General-attributes
  Group - default policy - GroupPolicy_196.219.202.197
  IPSec-attributes tunnel-group 196.219.202.197
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  pre-shared-key authentication local IKEv2 *.
  tunnel-group 185.52.118.67 type ipsec-l2l
  tunnel-group 185.52.118.67 General-attributes
  Group - default policy - GroupPolicy_185.52.118.67
  IPSec-attributes tunnel-group 185.52.118.67
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  pre-shared-key authentication local IKEv2 *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  anonymous reporting remote call
  HPM topN enable
  Cryptochecksum:8156993fef96da73dedfaacd7a14e767
  : end

  My local IP address: 10.2.X.X

  My remote IP address: 10.3.X.X

  Can anyone support me for the error

  Hello

  Your self after dynamic PAT takes the static NAT...

  NAT source auto after (indoor, outdoor) dynamic one interface

  You must reconfigure you NAT or PAT rule defined in your firewall.

  no nat source auto after (indoor, outdoor) dynamic one interface

  network local-lan-pat1 object

  10.2.0.0 subnet 255.255.255.0

  NAT dynamic interface (indoor, outdoor)

  !

  network local-lan-pat2 object

  10.60.1.0 subnet 255.255.255.0

  NAT dynamic interface (indoor, outdoor)

  !

  no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_10.3.0.0 NETWORK_OBJ_10.3.0.0 non-proxy-arp-search of route static destination
  !

  outside_cryptomap to access extended list ip 10.2.0.0 allow 255.255.255.0 host 10.3.0.0 255.255.255.0

  No list of extended outside_cryptomap access not allowed host ip DM_INLINE_NETWORK_1 10.3.0.0 object-group

  !

  We hope that you do this between subnets... not for the host at the other end.

  Concerning

  Knockaert

• problem with Ezvpn and VPN from Site to Site

  Hello

  I want to set Ezvpn and VPN Site to another but the problem is that the EasyVpn that would only work at the Site to the Site does not at all

  I have set up 1 card for two VPN with different tagged crypto

  I had execlude the traffice to NOT be natted to, and when I remove the Ezvpn site to another work well

  crypto ISAKMP policy 100
  BA aes
  md5 hash
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 10000
  BA aes 256
  preshared authentication
  Group 5
  key address 123456 crypto isakmp (deleted)

  ISAKMP crypto client configuration group easyvpn
  easyvpn key
  domain ezvpn
  pool easyvpn
  ACL easyvpn
  Save-password
  Split-dns cme
  MAX User 9
  netmask 255.255.255.0
  !

  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac vpn

  Crypto-map dynamic easyvpn 10
  Set transform-set dmvpn
  market arriere-route
  !
  !
  address-card crypto easyvpn local Dialer1
  card crypto client easyvpn of authentication list easyvpn
  card crypto isakmp authorization list easyvpn easyvpn
  client configuration address card crypto easyvpn answer
  easyvpn 100 card crypto ipsec-isakmp dynamic easyvpn
  easyvpn 1000 ipsec-isakmp crypto map
  defined by the peers (deleted)
  Set transform-set vpn
  game site address

  interface Dialer1
  the negotiated IP address
  IP mtu 1492
  NAT outside IP
  IP virtual-reassembly
  encapsulation ppp
  Dialer pool 1
  PPP authentication chap callin pap
  PPP chap hostname
  PPP chap password
  PPP pap sent-name to user
  easyVPN card crypto

  DSL_ACCESSLIST extended IP access list
  deny ip 100.0.0.0 0.0.0.255 101.1.1.0 0.0.0.255
  deny ip 100.0.0.0 0.0.0.255 70.0.0.0 0.0.0.255
  IP 100.0.0.0 allow 0.0.0.255 any
  refuse an entire ip
  easyvpn extended IP access list
  IP 100.0.0.0 allow 0.0.0.255 70.0.0.0 0.0.0.255
  IP extended site access list
  IP 100.0.0.0 allow 0.0.0.255 101.1.1.0 0.0.0.255

  Best regards

  The sequence number of card crypto for the static mapping crypto (site to site vpn) should be higher (ie: sequence number must be lower) than the ezvpn (map dynamic crypto).

  In your case, you must configure as follows:

  map easyvpn 10 ipsec-isakmp crypto
  defined by the peers (deleted)
  Set transform-set vpn
  game site address

  map easyvpn 150 - ipsec-isakmp crypto dynamic easyvpn

  Hope that solves this problem.

• PIX 515E for VPN remote site

  Hello

  7.0 (1) version pix

  ASDM version 5.0 (1)

  I have a situation where you go paas-thanks to the VPN feature goes on our PIX 515E. I tried to put this on the pix using a VPN Wizard Site to site

  who is enabled. I was unable to connect to the pix from the remote site. Witch's journal replied negotiate the pix is OK and the success

  The problem is when I try to set up the tunnel to the top of the remote site. I fall without failure.

  where can I see the vpn pix for error log?

  is there a manual for the solution of site to site VPN using the wizard

  Help, please.

  Thanks in advance

  http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_configuration_example09186a00804acfea.shtml#ASDM

  the section 'use adsm' (step 14) gives an example on how to set up vpn lan - lan via adsm

  Newspaper to go to the section "check".

• How can I block a VPN from site to Site traffic

  I configured a VPN from Site to Site, the wizard on a

  ASA 5510 and it works.

  However, I want to restrict http traffic only.

  I tried to change the ACL entry that allows ip traffic to allow only http traffic, but that seems to block all traffic and translates into a journal entry:

  Inbound TCP connection doesn't deny x to Y/80 SYN flags on the incoming interface.

  I managed to block pings by entering an ACL rule to specifically deny icmp, but I would like to deny all except http.

  Any advice on how to achieve this appreciated.

  William.

  Hello

  Guess that's what you're looking for. See the Bidirectional VPN filter configuration section.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml

• Limit remote traffic in a VPN from Site to Site

  I have a setup VPN from Site to Site in a lab using two ASA5505s environment.  VPN site to Site is functional however, what I wanted to do is to deny all traffic between the Remote LAN and not allow a single host to access the local network. Is it convenient or can it be done? If so, what Miss me the following ACL do not seem to effect?

  Remote LAN: 172.16.1.0/24
  LAN: 192.168.1.0/24

  outside_access_in list extended access permitted tcp 172.16.1.100 host 192.168.1.100 lytic 5000 10000
  outside_access_in list extended access deny ip 172.16.1.0 255.255.255.0 192.168.1.0 255.255.255.0
  Access-group outside_access_in in interface outside

  Appreciate any help that anyone can give.

  Hi tsabsuavyaj,

  By default, the sysopt connection VPN-enabled command is enabled which will bypass your list of access-interface referenced for all VPN traffic.

  To resolve this problem, you can:

  • Run the command No sysopt connection VPN-enabled. Caution with this, because it has global effect, which means it will interrogate ACL interface for all incoming VPN traffic.
  • Change your proxy-ACL (aka ACL interesting traffic) so that your remote control network is simply the address of the host that you would like to have access to your network. In so doing, nothing else is routed through your tunnel L2L at the remote end. This ACL must be mirrored on the other side (remote), so that the proxy-ACL must change so that its share of the 'Local network' is only the appropriate host and nothing else.

  Please let me know if you have further questions/clarification.

  Kind regards

  Kevin

  * Do not forget to note the useful messages but also to mark it as 'responded' once your problem is solved. This will help others find your solution more quickly.

• SA520W VPN from Site to Site with several VLANs

  Hello

  I have a customer here with several VLANS in their places who wants to set up a VPN from Site to site between 2 devices SA520W. Unfortunately I can not find a way to set it up. In the VPN policy, I can choose between everything (which is not what I want, I want only traffict between subnets the routed via VPN), IP address unique, a beach (in a subnet) and a subnet itself - but only one. I don't find a way to configure several subnets in the selection of local traffic and remotely. Adding another IKE policy between the 2 sites does not either (which is good normally).

  Any ideas? Anything I'm doing wrong?

  Thank you for your help.

  Best regards

  Thomas

  I know that if you have an ASA or a router, you can define as VLANS to pass through the tunnel.

  Do not have access to a SA520W to test...

  A recommendation might be to post the question on the SMB community where they answered questions related to this product, just to check what other people did.

  Federico.

• Remote VPN using Site 2 Site VPN

  Hi all

  I have 2 ASA 5505 firewall, VPN of Site 2 Site working between two firewalls. I have attached the visio diagram for my senario. I configured remote IPsec VPN in the firewall of the ASA-01, a capable user of connted to ASA-01 network via remote modem via VPN. As I set it up 2 a VPN between two ASA site, is possible only through remote VPN, a user can connect to ASA - 02.

  Thank you

  3 things. You must allow traffic to enter/exit the same interface to ASA - 01

  permit same-security-traffic intra-interface

  You must then add the new traffic lights to the existing acl for the lan to lan vpn. If ASA-02 network 192.168.2.0/24 and vpn client network 192.168.10.0/24 it would look like this.

  ASA-01

  access-list extended xxx permit ip 192.168.10.0 255.255.255.0 192.168.2.0 255.255.255.0

  ASA-02

  xxx list extended access permit ip 192.168.2.0 255.255.255.0 192.168.10.0 255.255.255.0

  and also the nat 0 ASA-02

  nat0 list extended access permit ip 192.168.2.0 255.255.255.0 192.168.10.0 255.255.255.0

  NAT (Inside) 0-list of access nat0

• Dynamic site using Paypal

  Can anyone recommend a tutorial that will help me set up a dynamic site using Paypal?

  I have some - although not much - experience with php and mySql and have put in place of the simple sites using Paypal buttons - I really want to learn to combine the two.  I have trouble finding what I understand on the site of Paypal and Googling, it evokes such a quantity of tutorials (mostly obsolete) I don't know where to start.

  Thank you

  Hello

  I have some - although not much - experience with php and mySql and have put in place of the simple sites using the Paypal buttons

  Create your site as you would for any other dynamic site but with an extra column in your table, place the code for your paypal button in this column.

  Follow links to any graphic for buttons when you paste the code.

  PZ

• VPN site to Site VPN dynamic + XAUTH Catch 22

  Hello world

  I'm working on a PIX 515e with 6.3 (3) 132 installed.  I'm having a problem of setting up a new VPN connection from site to site with a dynamic VPN are already in place.

  The problem is that the card encryption has xauth specified using the command 'authentication of customer card crypto'.  As it is my understanding that it is not possible to assign several cryptographic cards on the same interface, the new tunnel from site to site I am creating also requires xauth because its definition is under the same encryption card - which is a problem because the remote device does not support.

  Is there a way around this issue, or is the only thing we can do is to disable xauth and reconfigure endpoint on the other end of the dynamic connection?

  Thanks in advance

  Excerpt from the configuration:

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  MYmap 22 ipsec-isakmp crypto map

  correspondence address card crypto mymap 22 122

  card crypto mymap 22 set counterpart x.x.x.x

  card crypto mymap 22 transform-set 3des

  client authentication card crypto mymap AuthOutbound

  mymap outside crypto map interface

  Considering that:

  TUN 22 ipsec-isakmp crypto map

  crypto TUN 22 card matches the address 122

  card crypto TUN 22 set counterpart x.x.x.x

  card crypto TUN 22 value transform-set 3des

  TUN interface card crypto outside

  Might work, except the interface card switching to TUN crypto map would break the dynamic VPN.

  Hello

  The dynamic encryption card normally requires XAUTH for VPN clients.

  If you want to set up a tunnel from Site to Site and avoid XAUTH on this tunnel, you can do the following:

  # address x.x.x.x No.-xauth isakmp encryption key

  The idea is to disable XAUTH for each peer Site to Site specific in this way (dynamic clients will continue to work with XAUTH).

  Federico.

• Tunnel VPN from Site to Site dynamic

  I spent the last 2 days, try to set up a dynamic tunnel VPN site to site of a Cisco 5510 to a Cisco SA540. The 540 is a dynamic supplier that can not be changed. There a dyndns account.

  I was lucky that the other 10 sites are all static and the ADSM Assistant creates these tunnels without problems.

  What I try to do is:

  Is it possible to do it VIA ADSM?

  If this isn't the case, someone please in detail can help with orders.

  Kind regards

  PP

  Hello Paul,

  This is possible thanks to the ASDM, but you do have to use some advanced settings:

  Configuration > VPN Site to Site > advanced > Tunnel groups

  It change the group called "DefaultL2LGroup" and add the brightness button before the SA540 (Note: all of your sites with dynamic IP addresses will have the same key communicated in advance, if you have IPSec VPN clients, it will be a good idea to use a different key).

  

  Click ok and then apply.

  Then go to Configuration > VPN Site to Site > advanced > Crypto Maps and add a new entry dynamic

  

  Make sure that you match the phase 2 are on your SA540 (pictured ESP-AES-128-SHA), select a dynamic strategy and make the last sequence number (65535) then ok, apply.

  Then go to Configuration > VPN Site to Site > advanced > IKE policies and make sure you have corresponding policies of the phase 1.

  

  If no corresponding policy is found, add them.

  Through CLI:

  IKEv1 crypto policy 1

  preshared authentication

  aes encryption

  sha hash

  Group 2

  Crypto-map dynamic outside_dyn_map 65535 set transform-set ESP-AES-128-SHA ikev1

  CARD crypto ipsec-isakmp 65535 dynamic outside_dyn_map

  IPSec-attributes tunnel-group DefaultL2LGroup

  IKEv1 pre-shared-key *.

  I hope this helps.

• A dynamic Site static IOS ASA

  I had a hard time getting a VPN configuration from site to site with a dynamic address on IOS on a static address on ASA. I followed the example found here. http://www.Cisco.com/en/us/Products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml , but it won't work if I name the Group of Tunnel on the IP address of the WAN IOS port ASA if I use a generic name such as "cisco" as in the example, it will fail. Here's my current ASA configs and IOS. 192.168.7.5.0/24 is side LAN IOS and 192.168.254.0/24 side LAN ASA any help would be appreciated.

  You must use the tunnel group DefaultL2LGroup...

  tunnel-group DefaultL2LGroup type ipsec-l2l

• Configuration VPN from Site to Site on two ASA5505

  I have two ASA5505 ver 8.4 (6) and ver 9.0 (2) configured for a laboratory site to site vpn, but without success.  I could do everything outside address from two ASA ping, but could not ping the LAN on the other end of the ASA.  Here is the error message when you try to check if the VPN tunnel is established. For reference, the configurations are provided below.  Any help is very appreciated.

  ASA1 # show crypto isakmp his

  There are no SAs IKEv1

  There are no SAs IKEv2

  ASA1 # show crypto ipsec his

  There is no ipsec security associations

  ASA1:

  crypto ISAKMP allow outside

  the local object of net network

  subnet 192.168.1.0 255.255.255.0

  net remote object network

  Subnet 192.168.2.0 255.255.255.0

  !

  outside_1_cryptomap list of allowed ip object local net net access / remote

  tunnel-group 200.200.200.1 type ipsec-l2l

  IPSec-attributes tunnel-group 200.200.200.1

  pre-shared-key pass1234

  ISAKMP retry threshold 10 keepalive 2

  !

  part of pre authentication isakmp crypto policy 10

  crypto ISAKMP policy 10 3des encryption

  crypto ISAKMP policy 10 sha hash

  10 crypto isakmp policy group 2

  crypto ISAKMP policy life 10 86400

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  card crypto outside_map 1 match address outside_1_cryptomap

  card crypto outside_map 1 set pfs Group1

  peer set card crypto outside_map 1 200.200.200.1

  card crypto outside_map 1 set of transformation-ESP-3DES-SHA

  outside_map interface card crypto outside

  !

  NAT (inside, outside) 1 local static source net net-local destination static remote net net / remote

  output

  ASA2:

  crypto ISAKMP allow outside

  the local object of net network

  Subnet 192.168.2.0 255.255.255.0

  net remote object network

  subnet 192.168.1.0 255.255.255.0

  !

  outside_1_cryptomap list of allowed ip object local net net access / remote

  tunnel-group 100.100.100.1 type ipsec-l2l

  IPSec-attributes tunnel-group 100.100.100.1

  pre-shared-key pass1234

  ISAKMP retry threshold 10 keepalive 2

  !

  part of pre authentication isakmp crypto policy 10

  crypto ISAKMP policy 10 3des encryption

  crypto ISAKMP policy 10 sha hash

  10 crypto isakmp policy group 2

  crypto ISAKMP policy life 10 86400

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  card crypto outside_map 1 match address outside_1_cryptomap

  card crypto outside_map 1 set pfs Group1

  peer set card crypto outside_map 1 100.100.100.1

  card crypto outside_map 1 set of transformation-ESP-3DES-SHA

  outside_map interface card crypto outside

  !

  NAT (inside, outside) 1 local static source net net-local destination static remote net net / remote

  output

  ASA1 # sh run int

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  ASA1 #.

  ASA1 # ping 192.168.2.1

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes 192.168.2.1, time-out is 2 seconds:

  ?????

  Success rate is 0% (0/5)

  ASA1 # ping google.com

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 173.194.46.71, wait time is 2 seconds:

  !!!!!

  Success rate is 100 per cent (5/5), round-trip min/avg/max = 12/10/20 ms

  ASA1 #.

  ASA2 # sh run int

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  Shutdown

  !

  interface Ethernet0/3

  Shutdown

  !

  interface Ethernet0/4

  Shutdown

  !

  interface Ethernet0/5

  Shutdown

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  Shutdown

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.2.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  ASA2 # ping 192.168.1.1

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 192.168.1.1, time-out is 2 seconds:

  ?????

  Success rate is 0% (0/5)

  !

  ASA2 # ping google.com

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 173.194.46.64, wait time is 2 seconds:

  !!!!!

  Success rate is 100 per cent (5/5), round-trip min/avg/max = 14/10/20 ms

  ASA2 #.

  If you see any debugs the SAA, there is no encryption of any kind negoiations.

  The problem may be that you need to generate an interesting to match the ACL traffic.  I don't know if you on a physical laboratory or on GNS3.  If you use a physical laboratory, attach a laptop computer inside the interface and configure an IP address for this subnet.  You may need to do this for the other ASA.  Then iniatiate a ping to the other network.

• VPN from Site to Site and easy 871W

  I have a problem with the configuration of Site to site and easy both together on the same router 871W

  Something is working, but not everything.

  x.x.x.x - address IP WAN
  a.a.a.a - gw for WAN IP address
  z.z.z.z - IP address of the VPN Site-to Site
  192.168.201.0/25 - LAN
  192.168.200.0/24 - easy VPN address
  192.168.151.0/24 - Site-Site LAN

  Site-to-site work properly, everythings fine, but no easy VPN.

  Configuration of Cisco VPN Client:

  Home - x.x.x.x, group auth name - RemoteGroup, pass *.
  user test, pass *.

  I have a successful connection of Cisco VPN Client (I see a closed lock - connected status)

  Connection gave me the address 192.168.200.5.

  But I can't see LAN or LAN from Site to Site.

  And I don't have any idea what may be wrong.

  Finalny config:

  Quote:

  Current configuration: 8860 bytes ! version 12.4 no service button horodateurs service debug datetime msec Log service timestamps datetime msec encryption password service sequence numbers service ! hostname moj-waw-rtr ! boot-start-marker boot-end-marker ! logging buffered debugging 52000 Select the secret *. ! AAA new-model ! ! AAA authentication login default local AAA authentication login local remoteusers AAA authorization exec default local AAA authorization RemoteGroup LAN ! AAA - the id of the joint session ! resources policy ! IP subnet zero IP cef ! ! no ip domain search IP domain name waw.moj.pl name of the IP-server 194.204.152.34 name of the IP-server 193.178.240.2 ! ! Crypto pki trustpoint TP - self - signed-*. enrollment selfsigned the object cn = IOS-Self-Signed - Certificate name- revocation checking no rsakeypair TP - self - signed-*. ! ! crypto TP - self - signed pki certificate chain-*. certificate self-signed 01 quit smoking privilege secret 15 user username username secret privilege test 4 *. ! ! ! crypto ISAKMP policy 1 BA 3des preshared authentication Group 2 ISAKMP crypto key * address y.y.y.y the local address TOVPNPOOL pool-crypto isakmp client configuration ! ISAKMP crypto client configuration group RemoteGroup key *. pool TOVPNPOOL ISAKMP crypto vpnclient profile RemoteGroup group identity match function identity address 192.168.201.111 255.255.255.255 client authentication list remoteusers ISAKMP authorization list RemoteGroup client configuration address respond ! ! Crypto ipsec transform-set esp-3des esp-sha-hmac vpntowaw Crypto ipsec transform-set esp-3des esp-md5-hmac vpnwaw ! Crypto dynamic-map DYNAMICS 10 Set transform-set vpnwaw vpnclient Set isakmp-profile market arriere-route ! ! vpn_wro_waw 1 ipsec-isakmp crypto map defined peer y.y.y.y Set transform-set vpntowaw PFS Group1 Set match address 104 vpn_wro_waw card crypto 65535-isakmp ipsec dynamic DYNAMICS ! Bridge IRB ! ! interface FastEthernet0 spanning tree portfast

  
  !
  interface FastEthernet1
  spanning tree portfast
  !
  interface FastEthernet2
  spanning tree portfast
  !
  interface FastEthernet3
  spanning tree portfast
  !
  interface FastEthernet4
  Description $ETH - LAN$
  IP x.x.x.x 255.255.255.0
  IP access-group 102 to
  Check IP unicast reverse path
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  NAT outside IP
  IP virtual-reassembly
  route IP cache flow
  automatic duplex
  automatic speed
  vpn_wro_waw card crypto
  !
  interface Dot11Radio0
  no ip address
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  route IP cache flow
  !
  algorithms for encryption tkip encryption mode
  !
  encryption vlan 1 tkip encryption mode
  !
  SSID TO - WAW
  VLAN 1
  open authentication
  authentication wpa key management
  Comments-mode
  WPA - psk ascii *.
  !
  base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
  root of station-role
  No dot11 extensions aironet
  !
  interface Dot11Radio0.1
  encapsulation dot1Q 1 native
  no link-status of snmp trap
  No cdp enable
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 covering-disabled people
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  !
  interface Vlan1
  Description $ETH - SW - LAUNCH, INTF-INFO-HWIC $$ $4ESW
  no ip address
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP virtual-reassembly
  route IP cache flow
  IP tcp adjust-mss 1452
  Bridge-Group 1
  !
  interface BVI1
  IP 192.168.201.1 255.255.255.128
  IP access-group 101 in
  IP nat inside
  IP virtual-reassembly
  !
  local IP TOVPNPOOL 192.168.200.2 pool 192.168.200.101
  IP classless
  IP route 0.0.0.0 0.0.0.0 a.a.a.a
  !
  IP http server
  1 class IP http access
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  IP nat inside source static tcp 192.168.201.3 80 80 FastEthernet4 interface
  IP nat inside source overload map route SDM_RMAP_1 interface FastEthernet4
  !
  Remark SDM_ACL category of access list 1 = 1
  access-list 1 permit 192.168.201.0 0.0.0.127
  access-list 1 permit 192.168.151.0 0.0.0.255
  access-list 1 deny all
  Access-list 100 category SDM_ACL = 2 Note
  Note access-list 100 IPSec rule
  access-list 100 deny ip 192.168.201.0 0.0.0.127 192.168.3.0 0.0.0.255
  access-list 100 deny ip 192.168.201.0 0.0.0.127 192.168.2.0 0.0.0.255
  access-list 100 deny ip 192.168.201.0 0.0.0.127 192.168.151.0 0.0.0.255
  access-list 100 deny ip 192.168.201.0 0.0.0.127 192.168.200.0 0.0.0.255
  access-list 100 permit ip 192.168.201.0 0.0.0.127 all
  access list 101 remark self-generated by the configuration of the firewall SDM
  Note access-list 101 = 1 SDM_ACL category
  access-list 101 deny ip x.x.x.x 0.0.0.255 everything
  access-list 101 deny ip 255.255.255.255 host everything
  access-list 101 deny ip 127.0.0.0 0.255.255.255 everything
  access list 101 ip allow a whole
  Allow Access - list 101 tcp a whole
  access list 101 allow udp a whole
  access-list 101 permit icmp any one
  access-list 102 permit icmp any host x.x.x.x
  access-list 102 permit udp host 194.204.152.34 eq field host x.x.x.x
  access-list 102 permit udp host 193.178.240.2 eq field host x.x.x.x
  access-list 102 permit udp host host eq non500-isakmp x.x.x.x y.y.y.y
  access-list 102 permit udp host host eq isakmp x.x.x.x y.y.y.y
  access-list 102 permit esp host host x.x.x.x y.y.y.y
  access-list 102 permit ahp host host x.x.x.x y.y.y.y
  access-list 102 permit ip 192.168.151.0 0.0.0.255 192.168.201.0 0.0.0.127
  access-list 102 permit ip 192.168.200.0 0.0.0.255 192.168.201.0 0.0.0.127
  access-list 102 permit ip 192.168.2.0 0.0.0.255 192.168.201.0 0.0.0.127
  access-list 102 permit ip 192.168.3.0 0.0.0.255 192.168.201.0 0.0.0.127
  access-list 102 permit ip 192.168.201.0 0.0.0.127 all
  access-list 102 deny ip 10.0.0.0 0.255.255.255 everything
  access-list 102 deny ip 172.16.0.0 0.15.255.255 all
  access-list 102 deny ip 192.168.0.0 0.0.255.255 everything
  access-list 102 deny ip 127.0.0.0 0.255.255.255 everything
  access-list 102 deny ip 192.168.201.0 0.0.0.127 all
  access-list 102 refuse host ip 255.255.255.255 everything
  access-list 102 refuse host ip 0.0.0.0 everything
  access ip-list 102 permit a whole
  access-list 103 allow ip 192.168.200.0 0.0.0.255 any
  access-list 103 allow ip 192.168.151.0 0.0.0.255 any
  access-list 103 allow ip 192.168.201.0 0.0.0.127 all
  access-list 103 permit ip 192.168.2.0 0.0.0.255 any
  access-list 103 allow ip 192.168.3.0 0.0.0.255 any
  access-list 103 allow y.y.y.y ip 0.0.0.7 one
  access-list 103 deny ip any one
  Remark SDM_ACL category from the list of access-104 = 4
  Note access-list 104 IPSec rule
  access-list 104. allow ip 192.168.201.0 0.0.0.127 192.168.151.0 0.0.0.255
  access-list 104 allow 192.168.201.0 ip 0.0.0.127 192.168.2.0 0.0.0.255
  access-list 104 allow 192.168.201.0 ip 0.0.0.127 192.168.3.0 0.0.0.255
  access-list 104 allow 192.168.201.0 ip 0.0.0.127 192.168.200.0 0.0.0.255
  not run cdp
  allowed SDM_RMAP_1 1 route map
  corresponds to the IP 100
  !
  !
  control plan
  !
  Bridge Protocol ieee 1
  1 channel ip bridge
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  access-series 103 in
  privilege level 15
  entry ssh transport
  !
  max-task-time 5000 Planner
  end

  Bartosz,

  If you want to ping on the other side of the IPsec-L2L tunnel system you must change your 104 ACL.

  to read

  IP RA_VPN_POOL subnet REMOTE_SUBNET_MASK to allow REMOTE_SUBNET.

  access-list 104 allow 192.168.201.0 ip 0.0.0.127 192.168.200.0 0.0.0.255<---- this="" means="" ..="" put="" into="" the="" static="" l2l ="" tunnel="" traffic="" from="" my="" local="" subnet="" going="" to="" my="" remote="" access="" vpn="" ...="" seems="">

  Marcin