A dynamic Site static IOS ASA
I had a hard time getting a VPN configuration from site to site with a dynamic address on IOS on a static address on ASA. I followed the example found here. http://www.Cisco.com/en/us/Products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml , but it won't work if I name the Group of Tunnel on the IP address of the WAN IOS port ASA if I use a generic name such as "cisco" as in the example, it will fail. Here's my current ASA configs and IOS. 192.168.7.5.0/24 is side LAN IOS and 192.168.254.0/24 side LAN ASA any help would be appreciated.
You must use the tunnel group DefaultL2LGroup...
tunnel-group DefaultL2LGroup type ipsec-l2l
Tags: Cisco Security
Similar Questions
-
VPN site-to-site dynamic-to-static
Dear
I have a few sites already connected with ASA 5505 VPN site to site with both ending static IP address. Normally, all traffic can be found without any problems. Even, I used 'inside access management' for the two ASA.
Now I have a new office with only the ADSL pppoe. I used to install between Site B:remote the site dynamic IP and IP SiteA:static with a similar example of this easy VPN: http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805733df.shtml
All my ASA 5505 run 1 8.4 (4)
Site A - Static IP
Site B - Dynamic IP with pppoe connection.
After EasyVPN connected, I don't know how I remote manangment of the site a lan at the ASA 5505 B site?
Best regards
Alan.
If you're ok with or the other solution, it is probably easier to use dynamic to static lan-to-lan, so, at least, that your solution is consistent and fair use lan-to-lan tunnel instead of customer vpn solution mixture and lan-to-lan.
-
Troubleshooting IPSec Site to Site VPN between ASA and 1841
Hi all
in the past I've implemented several VPN connections between the devices of the SAA. So I thought a site link between an ASA site and 1841 would be easier... But it seems I was mistaken.
I configured a VPN Site to Site, as it has been described in the Document ID: SDM 110198: IPsec Site to Site VPN between ASA/PIX and an example of IOS Router Configuration (I have not used SDM but CCP).
I have run the wizards on the ASA with ASDM and the current IOS version 15.1 1841, with CCP.
It seems to Phase 1 and 2 are coming although my ASA in ADSM reports (monitoring > VPN > VPN statistics > Sessions) a tunnel established with some of the Tx traffic but 0 Rx traffic),
On the ASA:
Output of the command: "sh crypto ipsec its peer 217.xx.yy.zz.
address of the peers: 217.86.154.120
Crypto map tag: VPN-OUTSIDE, seq num: 2, local addr: 62.aa.bb.ccaccess extensive list ip 192.168.37.0 outside_2_cryptomap_1 allow 255.255.255.0 172.20.2.0 255.255.255.0
local ident (addr, mask, prot, port): (LAN-A/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (LAN-G/255.255.255.0/0/0)
current_peer: 217.xx.yy.zz#pkts program: 400, #pkts encrypt: 400, #pkts digest: 400
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 400, comp #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#send errors: 0, #recv errors: 0local crypto endpt. : 62.aa.bb.cc, remote Start crypto. : 217.xx.yy.zz
Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
current outbound SPI: 39135054
current inbound SPI: B2E9E500SAS of the esp on arrival:
SPI: 0xB2E9E500 (3001672960)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, PFS 2 group}
slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
calendar of his: service life remaining (KB/s) key: (4374000/1598)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001
outgoing esp sas:
SPI: 0 x 39135054 (957567060)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, PFS 2 group}
slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
calendar of his: service life remaining (KB/s) key: (4373976/1598)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001Output of the command: "sh crypto isakmp his."
HIS active: 4
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 4IKE Peer: 217.xx.yy.zz
Type: L2L role: initiator
Generate a new key: no State: MM_ACTIVEOn the 1841
1841 crypto isakmp #sh its
IPv4 Crypto ISAKMP Security Association
DST CBC conn-State id
217.86.154.120 62.153.156.163 QM_IDLE 1002 ACTIVE1841 crypto ipsec #sh its
Interface: Dialer1
Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120protégé of the vrf: (none)
local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
current_peer 62.153.156.163 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
current outbound SPI: 0xB2E9E500 (3001672960)
PFS (Y/N): Y, Diffie-Hellman group: group2SAS of the esp on arrival:
SPI: 0 x 39135054 (957567060)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505068/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEthe arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
SPI: 0xB2E9E500 (3001672960)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505118/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEoutgoing ah sas:
outgoing CFP sas:
Interface: virtual Network1
Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120protégé of the vrf: (none)
local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
current_peer 62.153.156.163 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
current outbound SPI: 0xB2E9E500 (3001672960)
PFS (Y/N): Y, Diffie-Hellman group: group2SAS of the esp on arrival:
SPI: 0 x 39135054 (957567060)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505068/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEthe arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
SPI: 0xB2E9E500 (3001672960)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505118/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEoutgoing ah sas:
outgoing CFP sas:
It seems that the routing on the 1841 is working properly as I can tear down the tunnel and relaunch in scathing a host on the network of 1841, but not vice versa.
Trounleshoot VPN of the 1841 report shows a message like "the following sources are forwarded through the interface card crypto. (172.20.2.0 1) go to "Configure-> routing" and correct the routing table.
I have not found an error on the 1841 config so if one of the guys reading this thread has an idea I appreciate highly suspicion!
It's the running of the 1841 configuration
!
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
host name 1841
!
boot-start-marker
start the system flash c1841-adventerprisek9 - mz.151 - 1.T.bin
boot-end-marker
!
logging buffered 51200 notifications
!
AAA new-model
!
!
AAA authentication login default local
!
AAA - the id of the joint session
!
iomem 20 memory size
clock timezone PCTime 1
PCTime of summer time clock day March 30, 2003 02:00 October 26, 2003 03:00
dot11 syslog
IP source-route
!
No dhcp use connected vrf ip
!
IP cef
no ip bootp Server
IP domain name test
name of the IP-server 194.25.2.129
name of the IP-server 194.25.2.130
name of the IP-server 194.25.2.131
name of the IP-server 194.25.2.132
name of the IP-server 194.25.2.133
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
object-group network phone
VoIP phone description
Home 172.20.2.50
Home 172.20.2.51
!
redundancy
!
!
controller LAN 0/0/0
atm mode
Annex symmetrical shdsl DSL-mode B
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
isakmp encryption key * address 62.aa.bb.cc
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description Tunnel to62.aa.bb.cc
the value of 62.aa.bb.cc peer
game of transformation-ESP-3DES-SHA
PFS group2 Set
match address 100
!
!
!
interface FastEthernet0/0
DMZ description $ FW_OUTSIDE$
10.10.10.254 IP address 255.255.255.0
IP nat inside
IP virtual-reassembly
automatic duplex
automatic speed
!
interface FastEthernet0/1
Description $ETH - LAN$ $FW_INSIDE$
IP 172.20.2.254 255.255.255.0
IP access-group 100 to
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1412
automatic duplex
automatic speed
!
ATM0/0/0 interface
no ip address
No atm ilmi-keepalive
!
point-to-point interface ATM0/0/0.1
PVC 1/32
PPPoE-client dial-pool-number 1
!
!
interface Dialer1
Description $FW_OUTSIDE$
the negotiated IP address
IP mtu 1452
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 2
PPP authentication chap callin pap
PPP chap hostname xxxxxxx
PPP chap password 7 xxxxxxx8
PPP pap sent-name of user password xxxxxxx xxxxxxx 7
map SDM_CMAP_1 crypto
!
IP forward-Protocol ND
IP http server
local IP http authentication
IP http secure server
!
!
The dns server IP
IP nat inside source static tcp 10.10.10.1 808 interface Dialer1 80
IP nat inside source static tcp 10.10.10.1 25 25 Dialer1 interface
IP nat inside source overload map route SDM_RMAP_1 interface Dialer1
IP nat inside source overload map route SDM_RMAP_2 interface Dialer1
IP route 0.0.0.0 0.0.0.0 Dialer1 permanent
!
logging trap notifications
Note category of access list 1 = 2 CCP_ACL
access-list 1 permit 172.20.2.0 0.0.0.255
Note access-list category 2 CCP_ACL = 2
access-list 2 allow 10.10.10.0 0.0.0.255
Note access-list 100 category CCP_ACL = 4
Note access-list 100 IPSec rule
access-list 100 permit ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
Note CCP_ACL the access list 101 = 2 category
Note access-list 101 IPSec rule
access-list 101 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
access-list 101 permit ip 172.20.2.0 0.0.0.255 any
Note access-list 102 CCP_ACL category = 2
Note access-list 102 IPSec rule
access-list 102 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
access-list 102 permit ip 10.10.10.0 0.0.0.255 any
!!
allowed SDM_RMAP_1 1 route map
corresponds to the IP 101
!
allowed SDM_RMAP_2 1 route map
corresponds to the IP 102
!
!
control plan
!
!
Line con 0
line to 0
line vty 0 4
length 0
transport input telnet ssh
!
Scheduler allocate 20000 1000
NTP-Calendar Update
NTP 172.20.2.250 Server prefer
endAs I mentioned previously: suspicion is much appreciated!
Best regards
Joerg
Joerg,
ASA receives not all VPN packages because IOS does not send anything.
Try to send packets to the 1841 LAN to LAN of the ASA and see is the "sh cry ips its" on the 1841 increments the encrypted packets (there not)
The problem seems so on the side of the router.
I think that is a routing problem, but you only have one default gateway (no other channels on the router).
The ACL 100 is set to encrypt the traffic between the two subnets.
It seems that the ACL 101 is also bypassing NAT for VPN traffic.
Follow these steps:
Try running traffic of LAN router inside IP (source of ping 192.168.37.x 172.20.2.254) and see if the packages are not through the translation and obtaining encrypted.
I would also like to delete 100 ACL from the inside interface on the router because it is used for the VPN. You can create an another ACL to apply to the interface.
Federico.
-
% 7-ASA-710005: request TCP thrown error in the Client VPN Site to CISCO ASA 5510
Hi friends,
I am trying to built customer to site VPN CISCO ASA 5510 8.4 (4) and get error below when connecting to a cisco VPN client software. Also, I'm below ASA, log. Please help me to reslove.
Error in CISCO VPN Client software:
Secure VPN connection terminated locally by the client.
Reason: 414: unable to establish a TCP connection.
Error in CISCO ASA 5510
7-ASA-710005%: TCP request and eliminated from
49276 outward: 10000 The ASA configuration:
XYZ # sh run
: Saved
:
ASA Version 8.4 (4)
!
hostname XYZ
domain XYZ
activate the password encrypted 3uLkVc9JwRA1/OXb N3
activate the encrypted password of R/x90UjisGVJVlh2
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
nameif outside_rim
security-level 0
IP 1.1.1.1 255.255.255.252
!
interface Ethernet0/1
full duplex
nameif XYZ_DMZ
security-level 50
IP 172.1.1.1 255.255.255.248
!
interface Ethernet0/2
Speed 100
full duplex
nameif outside
security-level 0
IP address 2.2.2.2 255.255.255.252
!
interface Ethernet0/3
Speed 100
full duplex
nameif inside
security-level 100
IP 3.3.3.3 255.255.255.224
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
!
boot system Disk0: / asa844 - k8.bin
passive FTP mode
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name xx.xx.xx.xx
Server name xx.xx.xx.xx
Server name xx.xx.xx.xx
Server name xx.xx.xx.xx
domain XYZ
network object obj - 172.17.10.3
Home 172.17.10.3
network object obj - 10.1.134.0
10.1.134.0 subnet 255.255.255.0
network object obj - 208.75.237.0
208.75.237.0 subnet 255.255.255.0
network object obj - 10.7.0.0
10.7.0.0 subnet 255.255.0.0
network object obj - 172.17.2.0
172.17.2.0 subnet 255.255.255.0
network object obj - 172.17.3.0
172.17.3.0 subnet 255.255.255.0
network object obj - 172.19.2.0
172.19.2.0 subnet 255.255.255.0
network object obj - 172.19.3.0
172.19.3.0 subnet 255.255.255.0
network object obj - 172.19.7.0
172.19.7.0 subnet 255.255.255.0
network object obj - 10.1.0.0
10.1.0.0 subnet 255.255.0.0
network object obj - 10.2.0.0
10.2.0.0 subnet 255.255.0.0
network object obj - 10.3.0.0
10.3.0.0 subnet 255.255.0.0
network object obj - 10.4.0.0
10.4.0.0 subnet 255.255.0.0
network object obj - 10.6.0.0
10.6.0.0 subnet 255.255.0.0
network object obj - 10.9.0.0
10.9.0.0 subnet 255.255.0.0
network object obj - 10.11.0.0
10.11.0.0 subnet 255.255.0.0
network object obj - 10.12.0.0
10.12.0.0 subnet 255.255.0.0
network object obj - 172.19.1.0
172.19.1.0 subnet 255.255.255.0
network object obj - 172.21.2.0
172.21.2.0 subnet 255.255.255.0
network object obj - 172.16.2.0
172.16.2.0 subnet 255.255.255.0
network object obj - 10.19.130.201
Home 10.19.130.201
network object obj - 172.30.2.0
172.30.2.0 subnet 255.255.255.0
network object obj - 172.30.3.0
172.30.3.0 subnet 255.255.255.0
network object obj - 172.30.7.0
172.30.7.0 subnet 255.255.255.0
network object obj - 10.10.1.0
10.10.1.0 subnet 255.255.255.0
network object obj - 10.19.130.0
10.19.130.0 subnet 255.255.255.0
network of object obj-XXXXXXXX
host XXXXXXXX
network object obj - 145.248.194.0
145.248.194.0 subnet 255.255.255.0
network object obj - 10.1.134.100
Home 10.1.134.100
network object obj - 10.9.124.100
Home 10.9.124.100
network object obj - 10.1.134.101
Home 10.1.134.101
network object obj - 10.9.124.101
Home 10.9.124.101
network object obj - 10.1.134.102
Home 10.1.134.102
network object obj - 10.9.124.102
Home 10.9.124.102
network object obj - 115.111.99.133
Home 115.111.99.133
network object obj - 10.8.108.0
10.8.108.0 subnet 255.255.255.0
network object obj - 115.111.99.129
Home 115.111.99.129
network object obj - 195.254.159.133
Home 195.254.159.133
network object obj - 195.254.158.136
Home 195.254.158.136
network object obj - 209.164.192.0
subnet 209.164.192.0 255.255.224.0
network object obj - 209.164.208.19
Home 209.164.208.19
network object obj - 209.164.192.126
Home 209.164.192.126
network object obj - 10.8.100.128
subnet 10.8.100.128 255.255.255.128
network object obj - 115.111.99.130
Home 115.111.99.130
network object obj - 10.10.0.0
subnet 10.10.0.0 255.255.0.0
network object obj - 115.111.99.132
Home 115.111.99.132
network object obj - 10.10.1.45
Home 10.10.1.45
network object obj - 10.99.132.0
10.99.132.0 subnet 255.255.255.0
the Serversubnet object-group network
object-network 10.10.1.0 255.255.255.0
network-object 10.10.5.0 255.255.255.192
the XYZ_destinations object-group network
object-network 10.1.0.0 255.255.0.0
object-network 10.2.0.0 255.255.0.0
network-object 10.3.0.0 255.255.0.0
network-object 10.4.0.0 255.255.0.0
network-object 10.6.0.0 255.255.0.0
network-object 10.7.0.0 255.255.0.0
network-object 10.11.0.0 255.255.0.0
object-network 10.12.0.0 255.255.0.0
object-network 172.19.1.0 255.255.255.0
object-network 172.19.2.0 255.255.255.0
object-network 172.19.3.0 255.255.255.0
object-network 172.19.7.0 255.255.255.0
object-network 172.17.2.0 255.255.255.0
object-network 172.17.3.0 255.255.255.0
object-network 172.16.2.0 255.255.255.0
object-network 172.16.3.0 255.255.255.0
host of the object-Network 10.50.2.206
the XYZ_us_admin object-group network
network-object 10.3.1.245 255.255.255.255
network-object 10.5.33.7 255.255.255.255
network-object 10.211.5.7 255.255.255.255
network-object 10.3.33.7 255.255.255.255
network-object 10.211.3.7 255.255.255.255
the XYZ_blr_networkdevices object-group network
object-network 10.200.10.0 255.255.255.0
access list XYZ extended ip 10.19.130.0 allow 255.255.255.0 145.248.194.0 255.255.255.0
access list XYZ extended ip 10.19.130.0 allow 255.255.255.0 host 172.16.2.21
access list XYZ extended ip 10.19.130.0 allow 255.255.255.0 host 172.16.2.22
access list XYZ extended ip 10.19.130.0 allow 255.255.255.0 host XXXXXXXX
Access extensive list ip 10.19.130.0 XYZ_PAT allow 255.255.255.0 any
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 host 195.254.159.133
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 host 195.254.158.136
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 any
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 209.164.192.0 255.255.224.0
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 host 209.164.208.19
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 host 209.164.192.126
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 208.75.237.0 255.255.255.0
Allow Access-list extended sheep 255.255.255.0 10.1.134.0 IP 10.7.0.0 255.255.0.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.17.2.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.17.3.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.19.2.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.19.3.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.19.7.0 255.255.255.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.1.0.0 255.255.0.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.2.0.0 255.255.0.0
Allow Access-list extended sheep 255.255.255.0 10.1.134.0 IP 10.3.0.0 255.255.0.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.4.0.0 255.255.0.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.6.0.0 255.255.0.0
Allow Access-list extended sheep 255.255.255.0 10.1.134.0 IP 10.9.0.0 255.255.0.0
Allow Access-list extended sheep 255.255.255.0 10.1.134.0 IP 10.11.0.0 255.255.0.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.12.0.0 255.255.0.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.19.1.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.21.2.0 255.255.255.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 172.16.2.0 255.255.255.0
access-list extended sheep allowed host ip 10.19.130.201 172.30.2.0 255.255.255.0
access-list extended sheep allowed host ip 10.19.130.201 172.30.3.0 255.255.255.0
access-list extended sheep allowed host ip 10.19.130.201 172.30.7.0 255.255.255.0
access-list extended sheep allowed ip object-group Serversubnet-group of objects XYZ_destinations
10.10.1.0 IP Access-list extended sheep 255.255.255.0 allow 10.2.0.0 255.255.0.0
10.19.130.0 IP Access-list extended sheep 255.255.255.0 allow host XXXXXXXX
IP 10.19.130.0 allow Access-list extended sheep 255.255.255.0 145.248.194.0 255.255.255.0
Access extensive list ip 10.8.108.0 Guest_PAT allow 255.255.255.0 any
CACIB list extended access permitted ip 10.8.100.128 255.255.255.128 145.248.194.0 255.255.255.0
Access extensive list ip 10.8.100.128 Cacib_PAT allow 255.255.255.128 all
Access extensive list ip 10.1.134.0 New_Edge allow 255.255.255.0 208.75.237.0 255.255.255.0
Allow XYZ_global to access extended list ip 10.7.0.0 255.255.0.0 10.1.134.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.7.0.0 255.255.0.0
Access extensive list ip 172.17.2.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.17.3.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.19.2.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.19.3.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.19.7.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 10.1.0.0 XYZ_global allow 255.255.0.0 10.1.134.0 255.255.255.0
Access extensive list 10.2.0.0 ip XYZ_global 255.255.0.0 allow 10.1.134.0 255.255.255.0
Allow XYZ_global to access extended list ip 10.3.0.0 255.255.0.0 10.1.134.0 255.255.255.0
Access extensive list 10.4.0.0 ip XYZ_global 255.255.0.0 allow 10.1.134.0 255.255.255.0
Access extensive list 10.6.0.0 ip XYZ_global 255.255.0.0 allow 10.1.134.0 255.255.255.0
Access extensive list ip 10.9.0.0 XYZ_global allow 255.255.0.0 10.1.134.0 255.255.255.0
Allow XYZ_global to access extended list ip 10.11.0.0 255.255.0.0 10.1.134.0 255.255.255.0
Access extensive list 10.12.0.0 ip XYZ_global 255.255.0.0 allow 10.1.134.0 255.255.255.0
Access extensive list ip 172.19.1.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.21.2.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.17.2.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.17.3.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.19.2.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.19.3.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.19.7.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.1.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.2.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.3.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.4.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.6.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.9.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.11.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.12.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.19.1.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.21.2.0 255.255.255.0
XYZ_global to access extended list ip 172.16.2.0 allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.16.2.0 255.255.255.0
Access extensive list ip 172.30.2.0 XYZ_global allow 255.255.255.0 host 10.19.130.201
XYZ_global list extended access allowed host ip 10.19.130.201 172.30.2.0 255.255.255.0
Access extensive list ip 172.30.3.0 XYZ_global allow 255.255.255.0 host 10.19.130.201
XYZ_global list extended access allowed host ip 10.19.130.201 172.30.3.0 255.255.255.0
Access extensive list ip 172.30.7.0 XYZ_global allow 255.255.255.0 host 10.19.130.201
XYZ_global list extended access allowed host ip 10.19.130.201 172.30.7.0 255.255.255.0
XYZ_global list extended access permitted ip object-group Serversubnet-group of objects XYZ_destinations
XYZ_global list extended access permitted ip object-group XYZ_destinations-group of objects Serversubnet
ML_VPN list extended access allowed host ip 115.111.99.129 209.164.192.0 255.255.224.0
permit access list extended ip host 115.111.99.129 ML_VPN 209.164.208.19
permit access list extended ip host 115.111.99.129 ML_VPN 209.164.192.126
permit access list extended ip host 10.9.124.100 Da_VPN 10.125.81.88
permit access list extended ip host 10.9.124.101 Da_VPN 10.125.81.88
permit access list extended ip host 10.9.124.102 Da_VPN 10.125.81.88
Da_VPN list extended access allowed host ip 10.9.124.100 10.125.81.0 255.255.255.0
Da_VPN list extended access allowed host ip 10.9.124.101 10.125.81.0 255.255.255.0
Da_VPN list extended access allowed host ip 10.9.124.102 10.125.81.0 255.255.255.0
Sr_PAT to access extended list ip 10.10.0.0 allow 255.255.0.0 any
Da_Pd_VPN list extended access allowed host ip 10.9.124.100 10.125.80.64 255.255.255.192
Da_Pd_VPN list extended access allowed host ip 10.9.124.100 10.125.64.0 255.255.240.0
permit access list extended ip host 10.9.124.100 Da_Pd_VPN 10.125.85.46
permit access list extended ip host 10.9.124.100 Da_Pd_VPN 10.125.86.46
Da_Pd_VPN list extended access allowed host ip 10.9.124.101 10.125.80.64 255.255.255.192
Da_Pd_VPN list extended access allowed host ip 10.9.124.101 10.125.64.0 255.255.240.0
permit access list extended ip host 10.9.124.101 Da_Pd_VPN 10.125.85.46
permit access list extended ip host 10.9.124.101 Da_Pd_VPN 10.125.86.46
Da_Pd_VPN list extended access allowed host ip 10.9.124.102 10.125.80.64 255.255.255.192
Da_Pd_VPN list extended access allowed host ip 10.9.124.102 10.125.64.0 255.255.240.0
permit access list extended ip host 10.9.124.102 Da_Pd_VPN 10.125.85.46
permit access list extended ip host 10.9.124.102 Da_Pd_VPN 10.125.86.46
Access extensive list ip 10.19.130.0 XYZ_reliance allow 255.255.255.0 145.248.194.0 255.255.255.0
access-list coextended permit ip host 2.2.2.2 XXXXXXXX
access-list coextended allow the host ip XXXXXXXXhost 2.2.2.2
permitted this access list extended ip 10.1.134.0 255.255.255.0 208.75.237.0 255.255.255.0
permitted this access list extended ip 208.75.237.0 255.255.255.0 10.1.134.0 255.255.255.0
access list acl-outside extended permit ip host 57.66.81.159 172.17.10.3
access list acl-outside extended permit ip host 80.169.223.179 172.17.10.3
access list acl-outside scope permit ip any host 172.17.10.3
access list acl-outside extended permitted tcp any host 10.10.1.45 eq https
access list acl-outside extended permit tcp any any eq 10000
access list acl-outside extended deny ip any any newspaper
pager lines 10
Enable logging
debug logging in buffered memory
outside_rim MTU 1500
MTU 1500 XYZ_DMZ
Outside 1500 MTU
Within 1500 MTU
IP pool local XYZ_c2s_vpn_pool 172.30.10.51 - 172.30.10.254
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ICMP allow any inside
don't allow no asdm history
ARP timeout 14400
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 208.75.237.0 obj - 208.75.237.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.7.0.0 obj - 10.7.0.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.17.2.0 obj - 172.17.2.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.17.3.0 obj - 172.17.3.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.19.2.0 obj - 172.19.2.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.19.3.0 obj - 172.19.3.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.19.7.0 obj - 172.19.7.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.1.0.0 obj - 10.1.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.2.0.0 obj - 10.2.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.3.0.0 obj - 10.3.0.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.4.0.0 obj - 10.4.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.6.0.0 obj - 10.6.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.9.0.0 obj - 10.9.0.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.11.0.0 obj - 10.11.0.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.12.0.0 obj - 10.12.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.19.1.0 obj - 172.19.1.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.21.2.0 obj - 172.21.2.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.16.2.0 obj - 172.16.2.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.201 obj - 10.19.130.201 destination static obj - 172.30.2.0 obj - 172.30.2.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.201 obj - 10.19.130.201 destination static obj - 172.30.3.0 obj - 172.30.3.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.201 obj - 10.19.130.201 destination static obj - 172.30.7.0 obj - 172.30.7.0 no-proxy-arp-search to itinerary
NAT (inside, all) static source Serversubnet Serversubnet XYZ_destinations XYZ_destinations non-proxy-arp-search of route static destination
NAT (inside, all) source static obj - 10.10.1.0 obj - 10.10.1.0 destination static obj - 10.2.0.0 obj - 10.2.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.0 obj - 10.19.130.0 destination static obj-XXXXXXXX XXXXXXXX - obj non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.0 obj - 10.19.130.0 destination static obj - 145.248.194.0 obj - 145.248.194.0 no-proxy-arp-search to itinerary
NAT source (indoor, outdoor), obj static obj - 10.1.134.100 - 10.9.124.100
NAT source (indoor, outdoor), obj static obj - 10.1.134.101 - 10.9.124.101
NAT source (indoor, outdoor), obj static obj - 10.1.134.102 - 10.9.124.102
NAT interface dynamic obj - 10.8.108.0 source (indoor, outdoor)
NAT (inside, outside) source dynamic obj - 10.19.130.0 obj - 115.111.99.129
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 195.254.159.133 obj - 195.254.159.133
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 195.254.158.136 obj - 195.254.158.136
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 209.164.192.0 obj - 209.164.192.0
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 209.164.208.19 obj - 209.164.208.19
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 209.164.192.126 obj - 209.164.192.126
NAT (inside, outside) source dynamic obj - 10.8.100.128 obj - 115.111.99.130
NAT (inside, outside) source dynamic obj - 10.10.0.0 obj - 115.111.99.132
NAT source (indoor, outdoor), obj static obj - 10.10.1.45 - 115.111.99.133
NAT (inside, outside) source dynamic obj - 10.99.132.0 obj - 115.111.99.129
!
network object obj - 172.17.10.3
NAT (XYZ_DMZ, outside) static 115.111.99.134
Access-group acl-outside in external interface
Route outside 0.0.0.0 0.0.0.0 115.111.23.129 1
Route outside 0.0.0.0 0.0.0.0 115.254.127.130 10
Route inside 10.10.0.0 255.255.0.0 10.8.100.1 1
Route inside 10.10.1.0 255.255.255.0 10.8.100.1 1
Route inside 10.10.5.0 255.255.255.192 10.8.100.1 1
Route inside 10.8.100.128 255.255.255.128 10.8.100.1 1
Route inside 10.8.108.0 255.255.255.0 10.8.100.1 1
Route inside 10.19.130.0 255.255.255.0 10.8.100.1 1
Route inside 10.99.4.0 255.255.255.0 10.99.130.254 1
Route inside 10.99.132.0 255.255.255.0 10.8.100.1 1
Route inside 10.1.134.0 255.255.255.0 10.8.100.1 1
Route outside 208.75.237.0 255.255.255.0 115.111.23.129 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication LOCAL telnet console
LOCAL AAA authorization command
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn2
Crypto ipsec transform-set esp-aes-256 ikev1, esp-md5-hmac vpn6
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn5
Crypto ipsec transform-set esp-aes-256 ikev1, esp-md5-hmac vpn7
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn4
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn1
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn_reliance
Crypto ipsec transform-set esp-3des esp-md5-hmac ikev1 c2s_vpn
86400 seconds, duration of life crypto ipsec security association
Crypto-map dynamic dyn1 ikev1 transform-set c2s_vpn 1 set
Crypto-map dynamic dyn1 1jeu reverse-road
card crypto vpn 1 corresponds to the address XYZ
card 1 set of peer XYZ Peer IP vpn crypto
1 set transform-set vpn1 ikev1 vpn crypto card
card crypto vpn 1 lifetime of security set association, 3600 seconds
card crypto vpn 1 set security-association life kilobytes 4608000
correspondence vpn crypto card address 2 DON'T
2 peer NE_Peer IP vpn crypto card game
2 set transform-set vpn2 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 2 set security-association
card crypto vpn 2 set security-association life kilobytes 4608000
card crypto vpn 4 corresponds to the address ML_VPN
card crypto vpn 4 set pfs
vpn crypto card game 4 peers ML_Peer IP
4 set transform-set vpn4 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 4 set - the security association
card crypto vpn 4 set security-association life kilobytes 4608000
vpn crypto card 5 corresponds to the address XYZ_global
vpn crypto card game 5 peers XYZ_globa_Peer IP
5 set transform-set vpn5 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 5 set - the security association
card 5 security-association life set vpn crypto kilobytes 4608000
vpn crypto card 6 corresponds to the address Da_VPN
vpn crypto card game 6 peers Da_VPN_Peer IP
6 set transform-set vpn6 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 6 set - the security association
card crypto vpn 6 set security-association life kilobytes 4608000
vpn crypto card 7 corresponds to the address Da_Pd_VPN
7 peer Da_Pd_VPN_Peer IP vpn crypto card game
7 set transform-set vpn6 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 7 set - the security association
card crypto vpn 7 set security-association life kilobytes 4608000
vpn outside crypto map interface
crypto map vpn_reliance 1 corresponds to the address XYZ_rim
card crypto vpn_reliance 1 set of peer XYZ_rim_Peer IP
card crypto 1 ikev1 transform-set vpn_reliance set vpn_reliance
vpn_reliance card crypto 1 lifetime of security set association, 3600 seconds
card crypto vpn_reliance 1 set security-association life kilobytes 4608000
card crypto vpn_reliance interface outside_rim
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
crypto isakmp identity address
No encryption isakmp nat-traversal
Crypto ikev1 enable outside_rim
Crypto ikev1 allow outside
IKEv1 crypto policy 1
preshared authentication
aes-256 encryption
sha hash
Group 5
lifetime 28800
IKEv1 crypto policy 2
preshared authentication
aes-256 encryption
sha hash
Group 5
life 86400
IKEv1 crypto policy 4
preshared authentication
aes-256 encryption
sha hash
Group 5
life 28000
IKEv1 crypto policy 5
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
preshared authentication
3des encryption
sha hash
Group 2
life 43200
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 10.8.100.0 255.255.255.224 inside
Telnet timeout 5
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
no basic threat threat detection
no statistical access list - a threat detection
no statistical threat detection tcp-interception
internal XYZ_c2s_vpn group strategy
username testadmin encrypted password oFJjANE3QKoA206w
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXXtype ipsec-l2l
tunnel-group XXXXXXXXipsec-attributes
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
type tunnel-group XYZ_c2s_vpn remote access
attributes global-tunnel-group XYZ_c2s_vpn
address pool XYZ_c2s_vpn_pool
IPSec-attributes tunnel-group XYZ_c2s_vpn
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
Review the ip options
!
global service-policy global_policy
level 3 privilege see the running-config command exec mode
logging of orders privilege see the level 3 exec mode
privilege see the level 3 exec mode command crypto
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:caa7476cd348ed89b95d37d4e3c9e1d8
: endXYZ #.
Good news
Follow these steps:
network object obj - 172.30.10.0_24
172.30.10.0 subnet 255.255.255.0
!
the LOCAL_NETWORKS_VPN object-group network
object-network 1.1.1.0 255.255.255.0
!
NAT (inside, outside) 1 static source LOCAL_NETWORKS_VPN destination LOCAL_NETWORKS_VPN static obj - 172.30.10.0_24 obj - 172.30.10.0_24 - route search
* Where 1.1.1.0/24 is the internal network that you want to reach through the tunnel.
Keep me posted.
Thank you.
Please note all messages that will be useful.
-
Dynamic to static L2L IPSec VPN
Hello
I've implemented a dynamic to static IPSec Site to Site VPN between a branch (ship) ASA5505 and headquarters. Now, this solution does not allow HQ initiate the IPsec connection.
There is a router behind the ASA5505. I heard that if I want to keep the tunnel upward, so that the HQ customers can switch the traffic to remote clients through the tunnel, I would need to run ALS IP icmp probes on the router behind the ASA.
Could someone explain how to implement it?
Thanks for your help.
Frank
The ICMP probe can be done through any device that is able to do ping, not only of the router.
The reason is that it is interesting traffic triggers the traffic is encrypted by the vpn tunnel, tunnel will stay up, so you will be able to open the connection to the AC to your remote site.
Hope that helps.
-
Dynamic to static IPSec with certificate-based authentication
I'm trying to implement a dynamic to static LAN2LAN vpn from an ASA 5505 (with a dynamic IP address) to an ASA5520 (with a static IP address)
I wish I had a small (/ 30) network on the side dynamics which I can connect to a larger (/ 24) network on the static side.
I also try to use the identity for authentication certificates.I produced a root and intermediate CA signed of the intermediate CA with the certificate authority root and then created identity cases for
the ASAs, signed with the intermediate CA using OpenSSL and imported to a trustpointI tried to use the instructions on:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080930f21.shtml
to configure certificates (replacing MS with OpenSSL) and following the instructions to:I tried the ASDM to set up the cert to identity appropriate on the external interface
[Configuration-> Device Management-> advanced-> SSL settings]and establish a connection profile [Configuration-> Device Management-> connection profiles] on both devices,
setting the part that gets its IP via DHCP static and the side that has the IP permanently to accept dynamic.I apply the settings, and nothing happens.
See the crypto isakmp just returns "there is none its isakmp.
I don't know where to start debugging it. How can I force the side DHCP to initiate a connection?
We are sure that both peers are using the same isakmp settings? It seems the policy that uses rsa - sig on one end uses a different Diffie-Hellman group.
-
VPN site to Site with an ASA behind Port Forwarding device
Hi, I want to configure a VPN from Site to site with an ASA with a public static IP adress and other ASA located behind a device with a public IP address that can forward ports to the ASA.
I have found no documentation for this configuration in the Cisco KB, anyone have a link for me or a brief description of the requirements?
Thank you
Tobias
Hello
Take a look at this documentation
http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094ecd.shtml
Hope this helps
-Jouni
-
Order of operations NAT on Site to Site VPN Cisco ASA
Hello
I have a question about the order of operations NAT on Site to Site VPN Cisco ASA 8.2.x. I have a scenario where the internal IP address of the range 10.17.128.x are NATTED IP public 31.10.10.x. below is the config:
Tunnel normally passes traffic to dmz - 31.10.11.10, 31.10.11.11 servers.
But the servers NATTED (10.17.128.x <->31.10.10.x) does not work.
inside_map crypto 50 card value transform-set ESP-3DES-SHA
tunnel-group 100.1.1.1 type ipsec-l2l
tunnel-group 100.1.1.1 General-attributes
Group Policy - by default-PHX_HK
IPSec-attributes tunnel-group 100.1.1.1
pre-shared key *.
internal PHX_HK group policy
PHX_HK group policy attributes
VPN-filter no
Protocol-tunnel-VPN IPSec svc webvpn
card crypto inside_map 50 match address outside_cryptomap_50
peer set card crypto inside_map 50 100.1.1.1
inside_map crypto 50 card value transform-set ESP-3DES-SHA
inside_map crypto 50 card value reverse-road
the PHX_Local object-group network
host of the object-Network 31.10.11.10
host of the object-Network 31.10.11.11
host of the object-Network 31.10.10.10
host of the object-Network 31.10.10.11
host of the object-Network 31.10.10.12
host of the object-Network 31.10.10.13
host of the object-Network 10.17.128.20
host of the object-Network 10.17.128.21
host of the object-Network 10.17.128.22
host of the object-Network 10.17.128.23
the HK_Remote object-group network
host of the object-Network 102.1.1.10
inside_nat0_outbound list extended access permitted ip object-group PHX_Local-group of objects HK_Remote
ACL_INSIDE list extended access permitted ip object-group PHX_Local-group of objects HK_Remote
ACL_OUTSIDE list extended access permitted ip object-group HK_Remote-group of objects PHX_Local
outside_cryptomap_50 list extended access permitted ip object-group PHX_Local-group of objects HK_Remote
Route outside 102.1.1.10 255.255.255.255 30.1.1.1 1
public static 31.10.10.10 (Interior, exterior) 10.17.128.20 netmask 255.255.255.255
public static 31.10.10.11 (Interior, exterior) 10.17.128.21 netmask 255.255.255.255
public static 31.10.10.12 (Interior, exterior) 10.17.128.22 netmask 255.255.255.255
public static 31.10.10.13 (Interior, exterior) 10.17.128.23 netmask 255.255.255.255
He started to work when I did another group of object by name PHX_Local1 and added to the list of access inside_nat0_outbound, instead of the object group PHX_Local, as below:
the PHX_Local1 object-group network
host of the object-Network 31.10.10.10
host of the object-Network 31.10.10.11
host of the object-Network 31.10.10.12
host of the object-Network 31.10.10.13
No inside_nat0_outbound access list extended only to allowed ip object-group PHX_Local-group of objects HK_Remote
inside_nat0_outbound list extended access permitted ip object-group PHX_Local1-group of objects HK_Remote
Can you please help me understand why group object PHX_Local failed with access-list inside_nat0_outbound, but he began to work with the Group of objects PHX_Local1.
Also, if you could tell me the order of operations to NAT via VPN Site to Site, it would be useful.
Thank you
Kind regards
Thomas
Hello
I think you could have said the original question in a way that could be missleading. In other words, if I understand now.
From what I understand now, you have the DMZ set up the server that are measured with a public IP address on the real servers. And for those that you have configured NAT0.
Then you have other servers that do not have public IP addresses themselves, but they are translated on the SAA.
If this is the case, then the next question would be. The server with the NAT should attend the L2L VPN connection with their real IP or address IP NAT.
Of course if you configure static NAT for the same servers and NAT0 the NAT0 will always win.
You have these guests who were not able to use the VPN L2L
31.10.10.10 10.17.128.20
31.10.10.11 10.17.128.21
31.10.10.12 10.17.128.22
31.10.10.13 10.17.128.23
IF you want them to go to the VPN L2L with their original IP address then you must configure
object-group, LAN
host of the object-Network 10.17.128.20
host of the object-Network 10.17.128.21
host of the object-Network 10.17.128.22
host of the object-Network 10.17.128.23
object-group, REMOTE network
host of the object-Network 102.1.1.10
inside_nat0_outbound list extended access allowed ip-group of objects LOCAL object-group remote
outside_cryptomap_50 list extended access allowed ip-group of objects LOCAL object-group remote
IF you want to use the L2L VPN with the public IP address, then you must configure
object-group, LAN
host of the object-Network 31.10.10.10
host of the object-Network 31.10.10.11
host of the object-Network 31.10.10.12
host of the object-Network 31.10.10.13
object-group, REMOTE network
host of the object-Network 102.1.1.10
outside_cryptomap_50 list extended access allowed ip-group of objects LOCAL object-group remote
EDIT: in this case you naturally do not configure any NAT0 for actual IP addresses we want precisely the IP addresses to be visible to the L2L VPN with the IP NAT address.
Or you can of course use the same "object-group" as currently but change the content in an appropriate manner
Be sure to mark it as answered if it was answered.
Ask more if necessary
-Jouni
-
KeepAlive to restore a dynamic to static tunnel?
Hi all
I have a dynamic to static 501 501 configuration of operating system 6.3 pix pix. I would use KeepAlive to re - establish the tunnel where the tunnel down. Is this possible?
Theres a workaround for any solution, you have the pix to the extreme end use a local ntp or server syslog, this traffic would bring the tunnel upward, as it has been defined as interesting.
-
Can anyone recommend a tutorial that will help me set up a dynamic site using Paypal?
I have some - although not much - experience with php and mySql and have put in place of the simple sites using Paypal buttons - I really want to learn to combine the two. I have trouble finding what I understand on the site of Paypal and Googling, it evokes such a quantity of tutorials (mostly obsolete) I don't know where to start.
Thank you
Hello
I have some - although not much - experience with php and mySql and have put in place of the simple sites using the Paypal buttons
Create your site as you would for any other dynamic site but with an extra column in your table, place the code for your paypal button in this column.
Follow links to any graphic for buttons when you paste the code.
PZ
-
Problem of site 2 site config dynamic to static
I must be missing something in the config, but I'm not sure.
Try to get a 506th PIX (6.3) at an ASA 5505 (7.2). The PIX is dynamic IP and the SAA is the static IP address. This is a second Site 2 site VPN between the PIX and PIX, another who has an IP staitic.
I tried everything I can think of. I think it's on the side of the ASA, but not sure. I have reset the pre shared key several times. I tried the sysopt connection permit-vpn on the SAA. He took command, but it does not appear in the config of runn. Put in ipsec-ra tunnels both ipsec-l2l as well as other things. In any case, I have attached my config.
Almost forgot, I used this link as a guide. http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805733df.shtml
Thanks for your help - Keith
Keith,
I think you should compare your ASA to static IP and the PIX for dynamic-IP configs - see what is different (apart from the names of things)
The pre-shared key, I used was test1234 at both ends.
-
ASA-dynamic to static VPN fails
I have an ASA 5510 with an address of STIC and a 5505 with a dynamics.
I created a dynamic the 5510 virtual private network. When the 5505 with it's dynamic address, tried to connect with me, I get the following errors:
' Mar 25 05:45:14 [IKEv1]: IP = 213.137.6.203, message received ISAKMP Aggressive Mode 1 with the name of the unknown group tunnel ' 213.137.6.203 '.
Mar 25 05:45:14 [IKEv1]: Group = DefaultRAGroup, IP = 213.137.6.203, Removing peer to peer table does not, no match!
Mar 25 05:45:14 [IKEv1]: Group = DefaultRAGroup, IP = 213.137.6.203, error: cannot delete PeerTblEntryI also get a similar error 5505 a aggressive Mode disabled
Looks like the 5510 believes it is an application for connection (site-to-site) L2L as opposed to a connection established dynamically. It doesn't have a group of tunnel for 213.137.6.203. You can create a group of tunnel with that name to resolve this problem.
The other option is to implement the ASA for a remote access connection (for example, Easy VPN).
Here's a URL that describes how to configure Easy VPN with NEM and L2L. HTH
http://www.Cisco.com/application/PDF/paws/100313/pixasa_easy_l2l_vpn.PDF
-
SonicWALL dynamic to static ASA
Forgive the almost matching repost of a question, which I had last week, but I wanted to be sure of something.
I now have a foreign Sonicwall which has a dynamic outside the address. I'll set up a tunnel to my ASA, which has a static address.
Of course the Sonicwall launches the connection.
I'm so clear:
On the SAA, I can set up a group of tunnel to accept the * dynamics * connection from the Sonicwall remote? Or is my only option to use the DefaultL2LGroup (main mode) or DefaultRAGroup (aggressive mode)?
Thank you!
Hello
You can do the following:
Crypto dynamic-map cisco 1 value transform-set ESP-3DES-MD5-ESP-3DES-SHA
Kind regards
-Gustavo
-
I do ikev2 VPN with the ASA and sites have a dynamic IP. A solution is to do a vpn site-to site, configure ASA headoffice with dynamic crypto map and the asa of the client with static cryptographic cards and put even the intellectual Headquarters property.
However, a better approach would be the classic scenario of ezvpn but I can't find a reference doc or config for ikev2. Is this supported using ikev2 or the only option, I have one I described above?
Hello
IKEv2 support for VPN tunnels easy on ASAs is not available, only for IKEv1.
It is available on routers Cisco, called FlexVPN:
FlexVPN on Cisco routers:
https://supportforums.Cisco.com/community/NetPro/security/VPN/blog/2012/...
Kind regards
Aditya
Please evaluate the useful messages and mark the correct answers.
-
VPN site to site & outdoor on ASA 5520 VPN client
Hi, I'm jonathan rivero.
I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.
the executed show.
ASA1 (config) # sh run
: Saved
:
ASA Version 8.0 (2)
!
hostname ASA1
activate 7esAUjZmKQSFDCZX encrypted password
names of
!
interface Ethernet0/0
nameif inside
security-level 100
address 172.16.3.2 IP 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 200.20.20.1 255.255.255.0
!
interface Ethernet0/1.1
VLAN 1
nameif outside1
security-level 0
no ip address
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/5
Shutdown
No nameif
no level of security
no ip address
!
2KFQnbNIdI.2KYOU encrypted passwd
passive FTP mode
object-group, net-LAN
object-network 172.16.0.0 255.255.255.0
object-network 172.16.1.0 255.255.255.0
object-network 172.16.2.0 255.255.255.0
object-network 172.16.3.0 255.255.255.0
object-group, NET / remote
object-network 172.16.100.0 255.255.255.0
object-network 172.16.101.0 255.255.255.0
object-network 172.16.102.0 255.255.255.0
object-network 172.16.103.0 255.255.255.0
object-group network net-poolvpn
object-network 192.168.11.0 255.255.255.0
access list outside nat extended permit ip net local group object all
access-list extended sheep allowed ip local object-group net object-group net / remote
access-list extended sheep allowed ip local object-group net net poolvpn object-group
access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group
pager lines 24
Within 1500 MTU
Outside 1500 MTU
outside1 MTU 1500
IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 100 burst-size 10
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 access list outside nat
Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1
Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1
Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1
Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec kilobytes of life security-association 400000
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
card crypto VPNL2L 1 match for sheep
card crypto VPNL2L 1 set peer 200.30.30.1
VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 20
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
!
!
internal vpngroup1 group policy
attributes of the strategy of group vpngroup1
banner value +++ welcome to Cisco Systems 7.0. +++
value of 192.168.0.1 DNS server 192.168.1.1
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value splittun-vpngroup1
value by default-ad domain - domain.local
Split-dns value ad - domain.local
the address value ippool pools
username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15
tunnel-group 200.30.30.1 type ipsec-l2l
IPSec-attributes tunnel-group 200.30.30.1
pre-shared-key *.
type tunnel-group vpngroup1 remote access
tunnel-group vpngroup1 General-attributes
ippool address pool
Group Policy - by default-vpngroup1
vpngroup1 group of tunnel ipsec-attributes
pre-shared-key *.
context of prompt hostname
Cryptochecksum:00000000000000000000000000000000
: end
ASA2 (config) #sh run
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec kilobytes of life security-association 400000
card crypto VPNL2L 1 match for sheep
card crypto VPNL2L 1 set peer 200.30.30.1
VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
VPNL2L interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 20
preshared authentication
3des encryption
md5 hash
Group 2
life 86400tunnel-group 200.30.30.1 type ipsec-l2l
IPSec-attributes tunnel-group 200.30.30.1
pre-shared key ciscomy topology:
I try with the following links, but did not work
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml
http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml
Best regards...
"" I thing both the force of the SAA with the new road outside, why is that? ".
without the road ASA pushes traffic inward, by default.
In any case, this must have been a learning experience.
Hopefully, this has been no help.
Please rate, all the helful post.
Thank you
Rizwan Muhammed.
Maybe you are looking for
-
Satellite L500 - lost wireless connection
My Satellite L500 recently lost the wireless connection. I looked towards the top of the Realtek wireless device in Device Manager and it says that the device is functioning properly. I tried to use "ping 192.168.1.1" join the router, and I get "erro
-
Can I fix it myself or should I take my computer to an expert?
-
Are there updates to Windows media player 11?
I have Windows Vista. Trying to get my Picasa on this PC for work and update my Player Windows media, #11.
-
OfficeJet Pro 8600 Premium error paper size does not match
I try to print an envelope #10 that I printed several times in the past, but today I get the error that the detected paper size does not match. I print on MS Word with the selected for the #10 envelope paper size. I loaded the envelope properly. W
-
¿Mediante can fornuis el packed Mx oficial con una subscripcion generalized annual?
Hace unos 16 years understanding her license oficial del pack Mx (flash, dreamweaver, fireworks, etc.) por un dineral entonces (€1.050). Ahora este fornuis querria package para get las staff of Diseño web current. ¿Hay manera get alguna rebaja in el