Inactive Ethernet adapter after Windows Update (9 March 03:03)

Similar Questions

• 450 HP: HP 450 Gen 2 Ethernet Driver missing / replaced by ISATAP Adapter After Windows Update

  Good afternoon

  I'm a network administrator at a small not-for-profit organization and aired on a particular issue with our 450 HP Gen 2.  Using Windows Deployment Toolkit, I have an image clean Windows 7 with the applications we want to push on these machines and then followed with update driver using the HP software Assistant.  In general, everything works.  But every so often, a 450 HP decides to 'lose' it's network, which is replaced by up to three non-working ISATAP adapt - hidden driver.  With hidden devices turned off, the Device Manager shows three network wireless, but not ethernet connections.  In addition, the NIC itself is completely dark; no nice little green/yellow lights sparkle.

  This was happening before with an image earlier established by my predecessor, and I discovered that this image was intended to HP 450 Gen1 and Gen2 not - even if the image has been labeled Gen2. Thought it was just a simple matter that the Gen1 image was not compatible with the Gen2 machines.  They would work for a little while, then break after a series of Windows updates.

  So I created my own image, repeat the steps above and for a while thought that the problem has been resolved.  But I just fell on my first 'disappeared' ethernet driver scenario; Since users employing 450 HP are usually off site, they need of working machinery.  But I have not found anything in the forums or through google search to indicate exactly what causes the problem.

  Currently, I use the HP of a DVD Software Wizard because the laptop has no ethernet connectivity to see if that solves it, but I'm interested to know what is causing this problem so I can avoid it in the future.  It's not good if users are bringing back machines to me who... was enough to say... do not work.

  I look forward to your correspondence.

  Best regards

  Robert

  Alrighty, I thought about it.  Essentially, (is no longer editable in the bios) LAN energy saving mode disables the NETWORK adapter, and once off, it will idle rest.  Therefore, your PC will not know to turn it on no matter how many times you restart or connect an ethernet.

  Here's the trick:

  1 unplug the power to your laptop, remove the battery, wait about 1-2 minutes.

  2. connect ethernet port NIC, connect the a/c, insert the battery.  Starts.  You should see your NETWORK card light up.

  3. once in Windows, go to the Device Manager.  You will see that your Realtek NIC listed.  Go into properties, power options and uncheck the option that reads LAN for energy savings.

  Problem solved.  I hope this helps the next guy.

  -Robert.

• Windows 8 Pro 64 bit not start nVidia nForce Ethernet driver after Windows Update

  Hello

  A couple of days, I installed Windows 8 Pro on my nForce 570 SLI with two ethernet interfaces integrated and an AMD processor and it seems to work very well. But then I installed all updates from Windows Update and now the ethernet drivers will not start. They worked very well until I did Windows Update facilities. I mean, otherwise I would not be able to do the Windows Update.

  Pilots initially in service to those who came with the installation of Windows 8 Pro. As a solution I forced the driver installation from the package of drivers nForce 15,58 for Windows 7 64 bit, but no change.

  The messages I get when making a diagnosis of Windows network is:
  Problems found
  The "Ethernet" adapter does not work correctly
  The 'Ethernet' knows of driver or hardware-related problems.

  The same messages for 'Ethernet 2 '.

  I was not able to find related reports in the event viewer

  Could someone help me please?

  Best regards
  LaurentZG

  Hello Manu,

  Thank you very much for your support.

  By chance, I found a post over in the Asus forum where a few other guys had the same problem. One of them stated that the specific ethernet chip has been sensitive to static electricity. If a light bulb then where I thought I should try to carry out the motherboard. So I unplugged the power cord and press the power button on my computer for about 30 seconds. Problem solved. Connection to the network is in use again :)

  Best regards
  LaurentZG

• USB ports not responding do not after windows update

  After a windows update in March/April 2012 all my usb ports stop working. The single port works now is the SATA USB combo.

  all I have this problem and know how to fix?
  Even a general difficulty just to get ports working again would be greatly appreciated.
  I've exhausted all other patches and now know that it is the windows update that caused the problem, so I'm forced to ask for help here.
  Thanks in advance for your time.

  Which has been updated by windows update is specific to your individual system, and if the USB failed in April you seem to have left ror a long enough period.

  Windows Update > history will show what has been installed.

  In a first time visit your manufacturers of PC and update or reinstall your chipset drivers.

  PS Theres no point mentioning patches unless you specify that you tried

• Good question after Windows update on Satellite P100 PSPA3E

  I encountered a problem with my sound card after a Windows Update. It became an old analog tuner with problems of dust on his volume knob. (this is a reference "sounds like" for those old enough to remember) I updated the driver to the most recent DriverGuide.com, no joy.

  I even did a complete system restore "with the"product restore disk."" Which fixed the problem until Windows updated the right files for trash again. I don't know what files do the dirty on my card since most of the windows system updates are performed while I "continue to work! Anyone with ideas?

  Thank you

  JD

  Hello

  What operating system do you use? XP or Vista?

  Satellite P100 PSPA3E must use a sound chip Intel high definition audio Conexant CX20551-22.

  I recommend to remove the sound card in Device Manager after installing Windows updates.
  Then restart the computer and install the latest audio drivers available that support the sound chip HD Conexant CX20551-22.

  First of all, you should try to use the driver for the Toshiba page. If this does not work, check the Intel page!
  Please don t forget to restart the laptop after windows update finished.

  Best regrads

• Satellite L500 - system hung on the splash screen after Windows update

  Hello

  I hope that someone can help you. My Satellite L500 is suspended on the blue startup screen after it restarted after a windows update, the mouse arrow moves and it seems to be a hard disk with a twinkle activity in the system lights. Except that nothing? Any ideas?

  Thank you
  Denise

  Hello

  > hung on the blue startup screen after it has restarted after a windows update
  This means that you get a blue screen after Windows update and more, you can start Windows t?

  You can start Windows in safe mode?

• Laptop Presario CG56: CG56 crashed after Windows Update

  After Windows update, set during the race, woke to find a "scree Orange" with the logo of Compaq.  Press F11 to enter in recovery mode has organized the restoration of the system for each restore point.  Finished with 0x8000ffff.  A ran the recovery system completely at the end.  Finished with the Orange screen.  Minimized ran impage recovery all the way to the end.  Repeat screen Orange.

  I find that the BIOS is corrupted in Windows Update, somehow.  I can get to the line of command in recovery mode, but I don't know what to do.

  Help!

  Me am HP Advanced System Diagnostics V3.0.3.0 by pressing f2 until the screen has finally come.  Do you have the System Diagnostics.

  Have you hard reboot by removing the battery, press the button for 15 seconds, extra power, hit start and the start up like a new PC was started and Windows.

• "limited connectivity" on after windows update wireless router.

  Original title: "limited connectivity" on after windows update wireless router. happens all the time after soundcards implemented to date. I then 'restore' on the eve of going online. Why?

  I have... 'limited connectivity' icon wireless router in the toolbar after windows updates. happens all the time after windows updates. I then 'restore' on the eve of going online. Why?

  Hello
   
  What operating system do you use?
   
   
  Method 1:
  Check the update has been installed and make a note of this update.
  To check, follow these steps:
  a. Click Start, in the search box, type in update
  b. click on windows Update
  c. click view update history
  Note: If this isn't a significant update, you can hide the update.
  To hide an update, follow these steps:
  a. open Windows Update by clicking on the button start. In the search box, type Update, and then in the list of results, click Windows Update.
  b. do one of the following:
  o click the link that tells you important updates are available if you have some updates to hide.
  o click the link that tells you optional updates are available if you have optional updates to hide.
  c. Select hide any update you want to hide, right-click and then click on update. Do this for each update you want to hide.
  d. click OK.
  
  If it an important update then you can try the following method 2:
  
  Method 2:
  Download the update of the article mentioned below (enter the number of the update in the search), put the computer to boot and then install the update and check if that helps:
  Download here: http://www.microsoft.com/download/en/default.aspx
  Clean boot: here is the link:
  http://support.Microsoft.com/kb/929135
   
  Note: When you're done to diagnose, follow step 7 in the article to start on normal startup.

• slow after windows update

  Hello
  After windows update:
  my PC slowing significantly
  Windows search sometimes opens spontaneously
  pages (explorer) sometimes becomes white and the icons disappear and takes a long time to be closed
   
  I have ms security essential and it is updated, so I do not think that my system is infected.
  Thank you.

  MajidNavabi,

  • See the following topics

  http://support.Microsoft.com/mats/system_maintenance_for_windows/en-us >

  http://support.Microsoft.com/FixIt/ >

  06/28 / 1106:37: 19 am

• Cannot connect to internet after Windows Update

  I was not able to connect to the internet after windows updates 7 of 14 October 2010, unless I have to restore the system to October 13.

  Hi jlm00926,

  ·        Update that you installed before the problem?

  ·        Are you able to connect to the internet properly now?

  You can set up your computer in a clean boot state. Subsequently, download & install the update manually from the Microsoft Download Center.

  http://www.Microsoft.com/downloads/en/default.aspx

  Clean boot will start Windows 7 by using a minimal set of drivers and startup programs and helps eliminate software conflicts.

  The following link has steps showing how to perform the clean boot: http://support.microsoft.com/kb/929135

  Note: Please make sure that the computer is configured to start as usual according to step 7 of the article: how to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7: http://support.microsoft.com/kb/929135

  Hope the helps of information. Please post back and we do know.
  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problems after Windows Update on Vista wireless

  It seems that other people have a similar problem, but I'll post this new...
  I've been running Windows Vista Ultimate on my Toshiba laptop for years without any problems.  Earlier this year, I started seeing issues after Windows updates.  The main problem is that after updates Windows, my wireless network is is more noticed and the wireless card (which was installed on the computer, and never had problems before) is not recognized.  I manually installed updated drivers with no luck.  The only thing that has worked is to do a system restore to a point before the updates.  The problem seems to be related to an update in general, I can't uninstall.

  I find it extremely ironic that I have no problems with Vista until Windows 7 is launched. First of all, it's the wireless card, then a problem with a driver graphics card (apparently... which seems to be fixed now) and return to the wireless card.  Should I expect to continue to have problems unless I upgrade to Windows 7?  I can't continue to spend half of my day trying to fix my computer after an update that is supposed to fix the errors, but I don't like the feeling that I am forced to upgrade.

  Hi dabaum77,

  From your post, it seems that the issue was occurring when Windows updates are installed automatically again even after the restoration of the system and that is why I suggest to restore the system again to a point before the updates and download and install Windows updates manually.

   

  Access the link below

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore
   
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  Follow these steps to disable the automatic updates:

   

  1. open Windows Update by clicking the Start button. In the search box, type Update, and then in the list of results, click Windows Update.

  2. in the left pane, click on change settings.

  3. under important updates, choose the option you want.

  4. under recommended updates, select the Give me recommended updates the same way I receive important updates check box, and then click OK. Need administrator permission if you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  
  Reference:
  http://Windows.Microsoft.com/en-us/Windows7/turn-automatic-updating-on-or-off

  
  Install the updates one by one and check the update is causing the problem to occur. If the problem persists due to a particular update, repeat the process and refrain from settling the problem causing the update to.

  
  You can also check the update problem in Windows Update history.

   

  Follow the steps to check which day caused the issue:
   
  1. open the control panel (all items view), and click the Windows Update icon.
     
  2. click on the link to view update history.
    
  3. to view the details of a single Windows Update-
  (A) select and right-click on a Windows Update list, and then click details.
  
  (B) click on close when finished.
   
   
  You can also uninstall the update that is causing the problem to occur, although it is not recommended.
   
  1. to uninstall a Windows Update, you must go to programs and features. There are several ways to find it. One of the simplest is to use the search box on the start menu.
   

  

  2. in the programs and features, click the link updates installed.
   

  

   
  3. after a few seconds, Windows Vista will load the list of installed updates. Scroll down the page until you find the update you want to delete, select it with the mouse and then click on uninstall.
   

  

   
  4. Windows Vista will ask you to confirm that you want to uninstall the update you selected. Click Yes and the uninstall process will begin.
   

  

   
  5 depending on the size of the update, the uninstall process may take from several seconds to several minutes.
   

  

  
  6. wait for the window above will disappear and, if necessary, restart your PC. The update is now deleted.
   
  
  Aziz Nadeem - Microsoft Support

• can I remove the patch uninstall program after Windows Update completed?

  can I remove the patch uninstall program after Windows Update completed?
  are the uninstall program is temporary file? or the update file?

  because my full HARD disk starting with the files

  can I remove the patch uninstall program after Windows Update completed?

  Only if you are sure that you will never need to uninstall the update of 100%.

  my full HARD disk starting with the files

  See this discussion archived instead-online http://aumha.net/viewtopic.php?f=62&t=33827

• I get a page_fault_in_nonpaged_area blue screen after Windows update yesterday.

  Hello
  I get a page_fault_in_nonpaged_area blue screen after Windows update yesterday. To do this, that every time I try to start the system.

  Whenever I try to start it gives options to start in safe mode, safe mode with network, safe mode with prompt etc., but all these options find you on the same blue screen with the error mentioned above, then it tries to restart with the same behavior over and over again.

  Any guidance will be appreciated. Thnx Nick

  Hello

  If you meet this new,
  http://mikemstech.blogspot.com/2011/12/troubleshooting-0x50.html

• Unable to start - blue screen after Windows update

  original title; on dell dimension C521... blue screen after Windows update last night 3/9...3:00am...running Vista

  Can not even go in safe mode

  Hello

  try to do a startup repair or a system restore before the update using the Startup Repair disk if you don't have a vista dvd microsoft

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  If you can make the above change how you receive updates to find the update problem

  When right-clicking on it UAC prompt you hide it

  http://www.bleepingcomputer.com/tutorials/tutorial140.html

  Choose one of these settings:

  Download updates but let me choose whether to install them - if you select this option, Windows will download the updates on your computer, but not install them automatically. If you want to install updates, then you must install them manually. You should only select this option if you have a reason to not install updates automatically. Only advanced users should use this option.

  Check for updates but let me choose whether to download and install them - if you select this option, you'll be alerted when there are new updates available for download and install. You can then choose to download and install the updates that you want. This option should really be reserved for people who know exactly which updates they need, or those who have little access to the Internet.

• Cannot view full screen flash and silverlight media after Windows Update

  problems with flash and silverlight Muslim poor after windows update said updated the driver and will not play in full screen right.

  Windows Update told to update the driver of the GUI.  After I did my computer do not play in full screen with flash and silverlight. It makes a square with 3 inches on each side.  previously, it would fill the entire screen.  I already talked to Nivdia and they helped me to install again and it runs right is not their product.  I don't know if it's the Avermedia driver then that is the problem.  I have windows vista 32 bit.  When I try to click with the right button on the silvery light, it causes the failed computer.  I uninstalled flash light and silver and it does not solve the problem.

  Windows Update told to update the driver of the GUI.  After I did my computer do not play in full screen with flash and silverlight. It makes a square with 3 inches on each side.  previously, it would fill the entire screen.  I already talked to Nivdia and they helped me to install again and it runs right is not their product.  I don't know if it's the Avermedia driver then that is the problem.  I have windows vista 32 bit.  When I try to click with the right button on the silvery light, it causes the failed computer.  I uninstalled flash light and silver and it does not solve the problem.

  ===================================
  It might be worth a try to do a system restore to
  an hour before installing the updated video driver.

  With the help of the Windows Vista system restore
  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.