increase ram g6 1147sl

Similar Questions

• Possible NB520-108 - increase RAM to 2 GB?

  Hello

  I don't want to increase the RAM which comes with the NB520-108. I know that one is 1 GB memory DDR3 at 1,066 MHZ. I can't find this speed, and my question is: can I put a 2 GB of DDR3 memory module 1.333 MHZ?

  Thanks to everyone in advance.

  Kind regards
  Ricardo

  Hey Buddy,

  I checked the specs on official site Web from Toshiba, and Yes, you can upgrade the memory up to 2 GB. That s the maximum capacity for this model of netbook.

  Installation of a module DDR3 at 1333 MHz is not a problem that faster because modules are compatible downgrade. This means that the module memory would go with 1066 MHz, but that s, no problem. The laptop will automatically be the clock speed.

• Satellite 35DVD - increase RAM

  I want to increase the RAM in my 35DVD, but it is not clear how to access the locations of memory. Can anyone here help with directions please?

  TIA

  Russell

  Hello

  It seems that the memoryslot is located under the keyboard. It must therefore take the machine part to mount a memory module.
  Be aware of the fact that it can take maximum total 192 MB. It has 64 MB fixed on the Board. This means that you can add max 128 MB and if there are already more than 64 MB in your system then you will need to remove this extra memory to be able to achieve a maximum memory capacity.

  Good luck

  Tom

• Increase ram > battery

  Hello

  increases the speed of the ram decreases the life of the battery of your laptop because mine has been upgraded to 1 GB

  Hello

  I can't imagine that the upgrade memory has much effect on the battery. But anyway, you can try to reduce your memory and look at the battery.

  Good bye

• Lenovo Z50 - 70 increasing ram for the gpu

  Hello!

  I have Lenovo z50-70 with amd Kaveri 7300 A10 and GPU R6 (all together known as RADEON Jet R6 M255DX). It has 1 GB of ddr3 ram allocated. Since I increased my ram I want to increase the ram on the gpu. How can I do?

  arotex wrote:

  Hello!

  I have Lenovo z50-70 with amd Kaveri 7300 A10 and GPU R6 (all together known as RADEON Jet R6 M255DX). It has 1 GB of ddr3 ram allocated. Since I increased my ram I want to increase the ram on the gpu. How can I do?

  In the old days, I remember that there is such a condition in the bios. However, I can't find in my Z500. Check the bios in your case.

• IdeaPad s300 increase ram of 4 GB to 8 GB or 16 GB

  I have 4 GB of ram in my model, it is possible to increase the RAM of this model? How many benches available memory for me? where I had 2 that I need to adapt to a 8 GB or 12 GB in total that I have to take it by force to another 4 GB? Thanks, sorry for my English

  Good day and welcome to the community.

  You can download the manual of your equipment:

  http://download.Lenovo.com/consumer/mobiles_pub/ideapad_s300_hmm_1st_edition_jul_2012.PDF

  Looking at page 37 of the manual, it seems to me that you have only one DIMM connector. I have no personal knowledge whether it is compatible with a 8 GB DIMMS, but there is at least a report that pretend to work here:

  http://forums.Lenovo.com/T5/IdeaPad-S-series-netbooks/S300-RAM-upgrade/TD-p/951675

  I hope this helps a little.

  Kind regards.

• How to increase ram on my toshiba c660 - 18 c

  the ram on my toshiba C660 - 18 c is (1 GB) Iam said that ram should be at least (2 GB)

  can you please tell me how I do this increase in ram please

  concerning

  Ron Flynn

  Hello Ron,

  This question would be better directed to Toshiba as they will be more familiar with the hardware architecture and which is compatible with the machine on a hardware level.

  Best regards

  Matthew_Ha

• increase ram 2 gb 6 GB shared memory does not increase

  I upgraded my ram that 2 GB to 6 GB but shared memory does not increase

  There are limits to the amount of memory can be used for shared graphics.

  Generally, configuring shared memory allocation is done in the BIOS.

• Why vector increase RAM plus table double?

  Hello!

  I have an app simple as3 Web that use Vector. < number > to store the numeric value. But it increase double RAM more table. For example:

  Use vector:

  private var myTest:Vector.<Number> = new Vector.<Number>();
  private function Test():void
  {
       for (var i:int = 0; i < 8192000; i++)
       {
            this.myTest.push(1.0);
       }
       trace("Length: " + this.myTest.length);
  }
  
  // Output: Length: 8192000
  // RAM in Task Manager ~ 65Mb
  

  Table use:

  private var myTest:ByteArray = new ByteArray();
  private function Test():void
  {
       for (var i:int = 0; i < 8192000; i++)
       {
            this.myTest.writeFloat(1.0);
       }
       trace("Length: " + this.myTest.length);
  }
  
  // Output: Length: 32768000
  // RAM in Task Manager ~ 32.5Mb
  b
  

  So, why vector increase my RAM double more table. How to fix this?

  Thanks in advance!

  a bytearray is not an array.

  If you compared to your use of vector with the use of ram ram a table, you will find that the vector uses less ram than the table.

  so, the real question is why a bytearray uses so much more efficient than an array and vector ram.  answer from the help files:

  The ByteArray class provides methods and properties to optimize reading, writing and working with binary data.

  Note: The ByteArray class is for experienced developers who need to access the data on the byte level.

  In memory data are a packaged (the most compact representation of the data type) byte array, but an instance of the ByteArray class can be manipulated with standard [] operators (access to a table). It also can be read and written to a file in memory, using methods similar to those in the URLStream and Socket classes.

  PS use scout to the flash profile, not the Task Manager.

• 1 Web site increases ram usage until Firefox slows, then crashes...

  Week or two ago FF33 started to have nits and jerky, gel and then crashed. I went through many support troubleshooting tips p (it comes crashing at this point) pages, uninstalled FF33, deleted files FF, that I could find, which was not all files, installed FF35 FF33, same result.

  Finally found my ram usage is high and paid attention to this. Reduced to 1 site constantly running up to the use of the ram. Regardless if 1 or 30 tabs of this Web site are open. If 1 tablet Omnium ram goes until it crashes. If none are open from this site, FF is fine. I've been on this site for many years without problems and really need to access.

  Any ideas how to solve the cause of that specific Web site?

  Thank you.

  Long answer, posted, empty response is entered. Anyway, great FF now.

• 23 b244 how to remove the rear to increase RAM

  I want to change the RAM, but I can't remove the back cover of my all in a single PC23-b244.

  What's the trick?

  Thank you

  Pokey13m

  Hello

  Did you check theHP Supportdocument on that?

  Jaco

  I'm not an employee of ch *.

  "" "" Please give a "Bravo, Thumbs Up" If the notice is relevant or "accept as Solution" to help other users of the forum having a similar problem.

• How to increase Ram on Satellite L305d-S5934?

  I need more ram than I thought. / 3GB is not enough. Any advice on what to do?

  I'm running itunes/internet explore and it got a little slow

  Hello

  Hey Buddy, 3 GB of RAM are sufficient if you use common tools like itunes/internet explore.

  In addition, you must know that a 32-bit OS, no matter if it s Vista or Win XP will recognize WHAT 3.2 GB due to the limitation of the 32 bit OS.

  I think an upgrade of RAM of 4 GB of RAM is useful if you use the 64-bit Windows OS and if you play high-performance games

• HP Pavilion 17 g 106nf: I have a HP Pavilion 106nf 17 g increase RAM.

  I have a HP Pavilion 17 g 106nf (energy star) and I want to upgrade the RAM.  What are the best RAM to get, Furthermore, how high can I do?

  Here is the Service Manual:

  Manuals

  It will take up to 16 GB of RAM, or 2 of these 8 GB modules:

  Module of memory of 8 GB 670034-005

  The problem is that this upgrade memory is very difficult. Requires the removal of the motherboard.

  See p. 116 of the manual.

  http://www.Amazon.com/Kingston-Technology-1600MHz-PC3-12800-KVR16LS11/DP/B00CQ35HBQ/ref=sr_1_2?ie=UTF8&QID=1463957621&SR=8-2&keywords=DDR3L-1600+so-DIMM

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• "HP Pavilion dv6-3136tx Entertainment Notebook PC Increasing RAM

  I want to indrease my 32GIG DDR3 6gig DDR3 RAM. My computer will be able?

  Hello

  Unfortunately no, the maximum ram for your laptop is 8 GB (IE 2 x 4 GB Modules).

  Kind regards

  DP - K

• I would like to get this right... adding assets to the Library increases RAM usage?

  I'm almost done with a fairly large RPG containing more than 2000 bitmap resources and music.  When I run this app in iOS, Android or on PC, my RAM usage is well above 100 MB. I have no script code.  The game is divided into about 100 classes AS3 (1 per level).

  As an experiment, I deleted all my code and packed an app 'empty '.  My RAM usage is always greater than 100 MB.  This leads me to believe that my entire libraray is loaded into RAM at the spearhead of my application.

  Is there a way to control or prevent this?  Class Loader? External assets EFA?

  Everything you have built in your application is loaded into memory when the application is deployed. There is nothing you can do about it.

  SWC will not help. CFC is used, primarily, as an external when creating library and all of the objects referenced in the creation will be always compiled into the application unless you use RSL and load additional libraries when running. By checking "merged into code" you always ask the compiler to include all assets. If you merge in code - you will need to write the logic that loads libraries during execution.

  The main issues in your case, it's that you compile media files in the application. Videos, sounds and, to a lesser extent, the images are the biggest hogs memory. You must load them during execution - do not include them in your application. In particular, it comes to sound files - Flash is very good runtime playback/streaming.

  When I say "runtime loading" I don't mean not necessarily load from the network/Internet. Given that you develop mobile applications (I guess with air)-you can write these assets in the file system during installation and then recover as needed.