INFRARED RECEIVER

Similar Questions

• E10: Update Rollup 1 for eHome Infrared Receiver for Win XP MCE 2005

  Hey all, yet another question.

  I'm on Qosmio E10 with MCE 2004.
  When I go to "Windows Update" I see something called "Update Rollup 1 for eHome Infrared Receiver for Windows XP Media Center 2005" (KB888795) Edition "»
  It is optional and install it I has yet because I'm not sure if I'm supposed to install at all since I'm on MCE 2004.

  I read another thread on this forum saying that this update completely screwed the infrared receiver on some configurations.

  So, question: Toshiba recommends installing this update for MCE 2005 on an MCE 2004 installation?

  (I was surprised that it appears in Windows Update despite my MCE 2004..., perhaps a bug of Microsoft?)
  Later,.

  Alcahest

  Hello

  My opinion is: don t touch a system running unless you are talking about an update to security... but MS recommends the update, so you can do the update, but it is at your own risk... as far as I know, Toshiba do support the software they offer with unit... not necessarily MS Update.
  In this case, you can try to run the update. If something goes wrong, you can roll back the OS with Restore tool.

  Good bye

• Disable the infrared receiver on Satellite A100 (PSAA9A)

  After the discovery of a new TV remote uses the same frequencies as my computer, my laptop now turn on or turn off whenever I have change the channel on the TV. I would switch the infrared receiver on my computer to avoid this problem. I assumed it would be connected to a COM port that I could simply turn off, but I can't find anything in the corresponding Manager feature of the infrared receiver.

  Any help you can provide would be great.

  Hello

  Check if you can find the IrDA device in Device Manager.
  There, you can try to disable the infrared receiver. Maybe it helps.

  Best regards

• Qosmio G40: Can I use the infrared receiver SMSCIR with other devices?

  My Qosmio G40 was a "SMSCIR infrared receiver" to be used by the remote controller.

  I wonder if it is possible to use this receiver with other software. For my non polar, I need an infrared receiver to send data from the watch to the laptop. On my old system, I had an iRDa port, which has been used for this purpose.

  If I can use the infraed receiver SMSCIR, I don't have to buy me a new USB-IRDA device.

  Thank you.

  From my own experience, you can use the iRDA only with the supplied infrared remote control.

• HP HDX16: what does an infrared receiver?

  I changed from VISTA to Win 8.1 and I received a message that my infrared receiver must be updated and I could upload it somewhere. WHAT is ENE CIR for? What do I do or does not? Thank you very much. Sorry for my ignorance...

  Upset.

  It is for the remote control of the sound and CD/DVD drive.

  Images here.

  https://www.Google.com/search?q=465541-001&rlz=1T4GGLS_enUS565US566&source=lnms&TBM=isch&SA=X&EI=n8_LVLWpK-jIsQS3mYGQBw&ved=0CAsQ_AUoBA&BIW=1600&BiH=773

  REO

• Problem with eHome Infrared Receiver Driver

  I have an IR receiver USB that I got from Dell which came with my old computer (XPS 210, I had to have my computer replaced if... the motherboard was fried on this subject). When I plug in the usual Windows searches for a driver and install. The driver for this is "eHome Infrared Receiver (USBCIR)" as it is listed in the device under USB devices Manager. After installation there is a green light on the receiver and everything works great, works by remote control (supplied with the receiver) very well as well.

  However, whenever I restart my computer, Windows detects the device again only as an unknown device. The receiver doesn't have a light on this subject, so it does not work. So that this work once again, I have to unplug and plug it in again.

  I tried to uninstall the device in Device Manager and install the driver again, but this does not solve the problem. I also tried different locations USB... does not help. I do not use hubs USB, just the slots on the tower. All my other USB devices work fine.

  I already searched the internet to find that apparently no one knows this problem. The receiver worked fine with my old computer, nothing was wrong. My old comptuer ran Windows Vista Ultimate 32-bit (x 86) but this one runs the same only 64-bit, could be the problem.

  OS: Windows Vista Ultimate (x 64-Bit)

  Any help is appreciated.

  Hi guys,.

  Did you guys check with Dell to see if they provide a 64-bit driver for the remote update? or with Phillips?  The firmware may need to be updated too if possible.

  Let us know if you need more assistance, Kevin
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error code 38 eHome Infrared Receiver does not

  Don't know.

  Error code 38 eHome infrared receiver (USBCIR) does not. Difficulty he coukd not reinstall driver because a former persists. __

  Go to the manufacturer and download the latest driver for your version of Vista and the device and install it manually (do not use the Fix - it).  This should solve driver problems (fi is the teason unit does not).

  I hope this helps.  Keep me posted.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• DV9417ca infrared receiver driver for Windows 7

  I was wondering if there is a driver that works with Windows 7.

  I tried sp44983.exe, sp44994.exe, and sp45214.exe, none of them does not seem to work.

  Thank you

  Thank you guys.  After a series of quarrels, I found that Win 7 supports the default receiver.  The problem turned out to be a low battery on the remote control.  The reason that he has escaped me, it's that I actually tested it under infrared on a camcorder, and I was convinced that the remote didn't work.  But apparently, the signal was not strong enough for the receiver.  A new battery and it worked like a charm.

  Guys Merry Christmas!

• Qosmio G30-195 - infrared receiver does not work after sleep

  Hi all!

  I have a problem on my laptop after Exchange of service of the motherboard.
  Once I booted Windows (Microsoft eHome transceiver) IR receiver works well in all programs, but when the system resumes from sleep mode, the IR receiver unloads from memory and can not find the search for material.

  If the remote control does not work until I have to restart Windows. Windows XP SP2 and Windows XP MCE behave the same. Before the exchange of motherboard I didn't you have a problem.

  What can I do with this?

  > What can I do with this?
  Contact service again and tell them the same thing. They need to know why this happen.

  By the way: you can use other USB devices connected after waking from sleep mode?

• Qosmio G50 - can I use infrared to other devices?

  Anyone could use before infrared receiver for other devices other then the remote control?

  I'm doing it recognize my phone and my Polar HRM but so far without success.

  What I see in Device Manager is appears as a device "Winbond" but it is also "eHome" of the WMC remote device?

  FIR (Fast Infrared) is rarely more because its very slow, requires line-of-sight and was replaced by BlueTooth.

  The G50 has a CIR (consumer IR) port that is not compatible with the devices of TREE. CIR is essentially just used for remote controls.

  Then you must either buy a fast USB infrared adapter, or you must use USB or Bluetooth on your device instead.

• Qosmio G40 - infrared chipset not detected by Windows 7

  I upgraded to Windows 7 from Vista and found that my infrared chipset (SMSC SIO1049 SuperIO chip) does not appear in Device Manager.
  According to this page, it should appear as an unknown driver (ACPI\SMCB0C0)
  http://msdn.Microsoft.com/en-us/library/dd567986.aspx

  The IR remote control provided by Toshiba does not work (it used to work fine under Vista). All the world had the same problem B4? How to fix you (if you resolved at all)?

  Does this mean that Ineed to wait for the next update of the BIOS (my BIOS version is 2.20)?

  My computer is a Qosmio G40 PQG40 02201NCE.

  Hello

  If the device is not visible in the Device Manager, not even as an unknown device, then this means that the device does not exist or was not detected by the BIOS.

  Usually, the infrared receiver must be visible in the Device Manager under:
  Human interface devices - > infrared receiver SMSCIR

  In system devices, you should see the device consumer infrared.

  Don't forget that you have enabled devices hidden sow option perhaps of Device Manager, then you might see this

  Please also check the BIOS
  I'm not very well if the infrared device option would be listed in the BIOS, but you should check it m

• Satellite A100: To receive data can I use the remote port IrDA?

  Hello

  I have an A100 which has infrared, which is used for the remote control supplied with the laptop. I was wondering if this infrared receiver can be used for other devices (e.g.: mobile phone) other than the remote control.

  I checked the control panel and Device Manager and both have no infrared information, but I thought that it would be always necessary even for the remote control.

  Help, please.

  Thank you.

  Hello

  I think that it s not possible to use the IrDA remote control window to receive files or data.
  I wonder how it should work if you don t have IrDA options in Control Panel.

  If this option is not available in the Control Panel, you cannot activate the IrDA and you can't assign a download or download the IrDA connection. So in my opinion you can't use it as a connection port.

  Unfortunately ;(

  But I found external solutions. If you want to use the IrDA, you can buy a USB IrDA key. I didn't test this device, but other people on the net have used it and it works.

• Satellite P100-PSPA3A-05S00P - how to use the remote control & infrared

  Satellite P100-PSPA3A-05S00P.

  Do not know if I have deleted the drivers or need drivers for remote control and infrared.
  I'm not sure how to activate the infrared but I got this cable look like an infrared receiver, but you don't know where it's going.

  I used the remote when I bought the laptop from 1st but it was a few years ago...

  Hello

  I think that infrared doesn t need to be activated. It s must already be enabled.
  But the remote control can be used within Windows Media Center.
  I think this will work because my friend of mouse remote control with Windows Media Center as well and it worked well.

• No requireed receiver remote control in Vista - Qosmio G30

  The G30 Vista versions do not need of the separate remote receiver, using the built-in IR receiver on the front panel.

  Update an Qosmio XP MCE to Vista simlilarly would not require the remote receiver separated, and it should be the Vista version of the remote control?

  Hello

  As far as I know the face before of the Qosmio G30-103 (it is a unit of XP MCE) for computer laptop, you'll find the windows of the infrared receiver and this sensor is able to receive signals from the remote control. BUT this is only supported using the Qosmio Player!
  For MCE, you will need the remote control receiver extra with a USB connector that usually comes with the laptop.

  Good bye

• Qosmio F30: Is there a way to get the remote to work directly with built in receiver

  My remote control Media Center only works when I plug the Receiver USB on my Qosmio F30 yet will work directly to the laptop with the vista media center pre program.

  Is there a way to get my remote to work directly on the built-in receiver?

  Steve.

  Hi Steve

  There is unfortunately no way to do it. Qosmioplayer is also part of the media offered by this book, and as you know this small Linux based application runs without booting the operating system. Due to this USB port can not be used (external receiver) and because of this one way remote control with Qosmioplayer is infrared receiver window.

  I'm not a technician and can explain you why this little infrared window is not used with the operating system running but, I'm sure, there must be a technical reason for it. Anyway, there is nothing to do, and you have to live with it. :(