Installation of a PIX - 4FE in a PIX525-UR

Similar Questions

• Ports Ethernet on PIX-4FE-66

  Hello

  I just inserted a PIX-4FE-66 ethernet card in my pix 515 firewall. In addition to eth0 eth1 en, I now see another inf2 interface. Wasn't supposed to see 4 additional ethernet ports? Ho I candy card. also I do not know which port is

  or E2, E3 etc can someone enlighten us in this for me please.

  Thank you.

  Greg, you need allow PIX-515-SW-R-UR = manufacturer, to convert the restricted (R) to HEART.

  Please evaluate the useful messages

  Rgds

  Jorge

• A question about the old Pix 515

  Hi Experts.

  My client needs additional interfaces of FE and do not want to migrate the chassis 515E.

  Can the data sheet of the former 515 Pix no longer available due to the declaration of the EOS, you please confirm that the Pix 515 supports 1FE - PIX and PIX - 4FE cards before ordering one of them?

  Thank you

  The 515 supports 4 interface cards. Make sure they are running a UR pix license if - 515R takes only supported 3 interfaces.

• Basic router and PIX during installation of ADSL

  I have a router with a WIC ADSL card 1751, a 506th PIX and a 24 port Catalyst 2950. The office is connected via ADSL with a public IP address. I also have a router ADSL 837 (but I don't think I'll need with the map of ADSL in the 1751). I need to set up a WAN connectivity, a static tunnel site to another and also allow access to the Cisco VPN client. I was wondering if anyone had any suggestions or examples of configurations for me initially on the right track with this. I wanted to also be the router or PIX hand addresses DHCP. In addition, I never configured (ADSL) ATM card into the router. I don't know if I need to assign the public IP address or this bridge for the PIX.

  Thank you very much

  Hello...

  I presume that the firewall is connected to the inside interface of the router. the firewall's default gateway is the IP Address of the ISP router. right? Now, configure the DHCP protocol and other things as said in the previous post...

  On the firewall, all traffic between inside and outside is open. so, you don't connect on an inside vpn server. Let us know if you need more information.

  For site-to-site ipsec tunnel, refer to the following URL.

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00801c4445.shtml#configs

  See the configurations on the PIX and replicate in your condition.

  REDA

• Installation of site to site VPN IPSec using PIX and ASA

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  I am a site configuration to site IPSec VPN using a PIX515E to site A and ASA5520 to Site B.

  I have attached the lab diagram. Consider PIX and ASA are in default configuration, which means that nothing is configured on both devices.

  According to the scheme

  ASA5520

  External interface is the level of security 11.11.10.1/248 0

  The inside interface is 172.16.9.2/24 security level 100

  Default route is 0.0.0.0 0.0.0.0 11.11.10.2 1

  PIX515E

  External interface is the level of security 123.123.10.2/248 0

  The inside interface is 172.16.10.1/24 security level 100

  Default route is 0.0.0.0 0.0.0.0 123.123.10.1 1

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  Could someone tell me how to set up this configuration? I tried but didn't workout. Here is the IKE protocol I have used.

  IKE information:

  IKE Encrytion OF

  MD5 authentication method

  Diffie Helman Group 2

  Failure to life

  IPSEC information:

  IPsec encryption OF

  MD5 authentication method

  Failure to life

  Please enter the following command

  on asa

  Sysopt connection permit VPN

  on pix not sure of the syntax, I think it is

  Permitted connection ipsec sysopt

  What we are trying to do here is basically allowing vpn opening ports

  Alternatively you can open udp 500 and esp (or port ip 50) out to in on the two firewalls

• Just got a new Pixi, updated to 1.3.5 update and now I can't download apps

  Hello!

  I just bought a Pixi yesterday and downloaded a few apps (Facebook, Flixster) and everything was OK.  I noticed Facebook saying that I had to update to WebOS, so I did.

  After the installation of WebOS, I can't download apps.  I followed the palm offers fixes and none of them helped.

  I rebooted my phone a few times (both by choosing reboot and turning off and on again), put in my credit card information and checked for if sure I have a spare bedroom (say 7 GB of free...) and I can't download apps.

  I tried the free and paid apps.  Download including Pandora, enjoy Sudoku, crossword, Accuweather and GoodFood... and none of them.

  I get no error message at all.  I click on the download button, it displays "Download" and then it switches back on a Download"" button.  He will ask me if I agree the application using location services, too... but nothing will download.

  I looked through the forums and couldn't find something relevant?  It seems most of downloads problems producing some sort of error.  Here, I get nothing.  And before the 1.3.5 update, I was able to download apps very well.

  Any ideas?

  Just came across other people having this problem with the pixi. Seems to be related to the pixi only. And it was the people who had no installed 3rd party settings. This solves the problem for all who have tried so far. Run webos doctor found at the link below. Follow the directions. You must back up all files stored on the USB of the Pixi drive. Music, you took pictures, files, etc. Also, be sure to run the backup application in the Launcher to a current backup before wipe everything with the webos doctor. I would like to know if it works for you.

  http://www.Palm.com/us/support/downloads/pre/RecoveryTool/webosdoctor_dl_pixi_sprint_en.html

  Message edited by tagz on 31/12/2009 21:32

• Cisco VPN Client Authentication - PIX 515E-UR

  Hi all

  I need your expert help on the following issues I have:

  1. I would like to create more than 1 client VPN on my PIX-515E groups. This is so that I can give a different part of the internal network access to different type of VPN connection. For example, I want a group to have no XAUTH, while the other group must use RADIUS XAUTH. Is it possible for me to do this? I see the PIX automatically enable RADIUS on both groups of VPN clients.

  2. the RADIUS server is a Microsoft ISA with IAS server and it is located on the PIX inside interface. The VPN endpoint is external interface of the PIX. Is there a problem with this Setup? Do I need to have the RADIUS server that is located on the external interface?

  3 can. what command I use to debug RADIUS authentication?

  Thanks in advance for your help.

  Hi vincent,.

  (1) you can use the vpngroup *-authentication server ipaddress to specify the IP address of the Radius Server on a particular group... If you do not specify this, the authentication of the user is made locally... also check for vpngroup * order of user authentication

  (2) there should be no problem with the installation of your... should work fine... If the RADIUS is outdoors, it is subject to many attacks... so have it inside...

  (3) use the "RADIUS session debug" or "debug aaa authentication..."

  I hope this helps... all the best... the rate of responses if found useful

  REDA

• VPN concentrator + PIX on LAN-> customers can not reach local servers

  Hello

  I have a problem wrt. remote access clients coming via a VPN3000 concentrator and trying to access local servers.

  For the topology:

  The internal network is 10.0.1.0/24. It connects with the outside world, as well as via a PIX DMZ; the PIX has 10.0.1.1 in the internal network.

  On the same LAN (internal), I have the VPN concentrator for the inside address 10.0.1.5. It assigns addresses in the 10.0.100.0/24 range to the

  VPN client-PCs.

  I can sucessfully connect using the VPN client SW to the hub, i.e. remote access clients out addresses

  the 10.0.100.0/24 range.

  The problem: access from VPN clients to internal network is * not * possible; for example, a customer with 10.0.100.1 cannot connect to

  internal to the 10.0.1.28 server.

  To my knowledge, this is a routing problem because the server (10.0.1.28) has no idea on how to reach customers in

  10.0.100.0/24. The only thing that the server is a default static route pointing to the PIX, i.e. 10.0.1.1.

  So I set up a static route on the PIX for 10.0.100.0 pointing to the hub-VPN, that is

  Mylan route 10.0.100.0 255.255.255.0 10.0.1.5 1

  This does not solve my problem though.

  In the PIX logs, I see the entries as follows:

  % 3 PIX-106011: deny entering (no xlate) tcp src trainee: 10.0.1.28 (atlas) / 445 intern dst: 10.0.100.1 (pending) 1064

  The PIX seems to abandon return packages, i.e. traffic from the server back to the client

  To my knowledge, the problem seems to be:

  Short traffic VPN - client-> Concentrator VPN-> Server-> PIX - where it gets moved.

  My reasoning: the PIX only sees the package back, i.e. the package back from the server to the client - and therefore decreasing the

  package because he has not seen the package from the client to the server.

  So here are my questions:

  (o) how do I configure the PIX that I be connectivity between my remote VPN clients (10.0.100.0/24) and

  computers servers on the local network (10.0.1.0/24)?

  (o) someone else you have something like this going?

  PS: Please note that the first obvious idea, installation of static routes on all machines on the local network is not an option here.

  Thank you very much in advance for your help,.

  -ewald

  Hello, PIX the because can not route traffic on the same interface (prior to version 7.0 anyway), I suggest you two places your hub to the outside with the inside of the legs on a zone demilitarized or (if you can not do a makeover of the network) you remove your pool with 10.0.100.0 - addresses and create a pool with 10.0.1.0 - addresses which is a part of the address space. No, NOT all. A little book that it is not used inside.

  Best regards

  Robert Maras

• PIX 520 model CO or MAKE

  Gentlemen

  Last night I was reading my release notes for my 16 MG ISA Flash card before installing in my PIX 520. The release notes indicate that I have to check if I have a 520 PIX "CO" or "MAKE". A worm show command does not reveal this? I have a small white sticker on the box that says "PIX 520" with no further details.

  How can I determine if I have one of these models 'CO' or 'DOING '. It is safe to assume that if she does not, I can go ahead with the upgrade?

  Also, I have 2 of these cards to 16 mg. I can put the two or is 16 Cape on Flash... I ask because I want to code ver 6.2.2. In addition to install PDM version 2...

  Thank you

  Kevin

  It usuallt you indicates on the label, but you can tell by the serial number as well.

  A0 PIX are between 18005000-18013334

  B0 PIX are between 18013335-18015503

  C0 PIX are between 18015504-18025676

  D0 and E0 are 18025677 and more

  Note that there may be a 44 in front of these numbers on your serial number label.

  Also note that the installation instructions say the 16Meg card is not compatible with the PIX of C0 (or at least he used to say that), it won't and you can install this card without problem.

  Make sure that you first remove the existing 2Meg card, otherwise the PIX will not work. The card is one without the external connectors on it at the back.

  You can only put one of these cards in, no need for both. You will be able to load 6.2 (2) and PDM with no problems.

• Check the process of cpu on a Pix 525 Version 7.2 (2)

  Hi all,

  A few hours ago I got a high CPU usage on my Pix 525 Version 7.2 (2), I wanted to check what process was taking all the CPU, but I noticed that there is no command "show processes".

  I was able to see the percentage of CPU utilization (cpu, CPU utilization show show) but not the list of processes, does anyone know how can I check this?

  Thanks in advance for your help.

  Hi Alfonso,.

  There should be a command "show processes" in 7.2 (2). Make sure you have the appropriate permissions to use this command.

  There's even a command 'show proc cpu-hog' who will show you the last three albums CPU hogging deals, and when they were last hogging CPU:

  Pix525/pri/law # sh proc cpu-hog

  Process: Unit, shipping NUMHOG: 2, MAXHOG: 7158, LASTHOG: 110

  LASTHOG at: 19:38:57 EDT April 3, 2009

  PC: 113a4b

  Traceback: 1154a 0 1123f0

  Process: this / console, NUMHOG: 2, MAXHOG: 330, LASTHOG: 320

  LASTHOG at: 11:53:57 EDT July 18, 2007

  PC: fe809d

  Traceback: 1008 has 51 10087 1007ee3 has 6 100ae4f 1021716 10216d 3 102142a

  101d0dd 100 c 149 100bee3 100bcb4 ffe27a febbb4 1006b 26

  Process: ssh, NUMHOG: 8, MAXHOG: 238, LASTHOG: 230

  LASTHOG in: 02:00:37 EDT April 27, 2009

  PC: 100a 720

  Traceback: 10087f6 100ae4f 102166a 102142 has 101d0dd 100 c 149 100bee3

  100bcb4 ffe27a febbb4 10069e5 ff8806 fea054 1006b 26

• PIX 7.2 (4) does not not on free WILL

  I have a VPN between a Pix525 (7.2 (4)) and a 2811 router. The VPN works perfectly except for the GRE packets.

  I have a tunnel running behind the PIX with a source of a.a.a.a tunnel and b.b.b.b. tunnel destination I have an access list on the Pix with a list of matching permit ip host a.a.a.a host b.b.b.b.

  So far, I have:

  1 Ping a.a.a.a with a b.b.b.b source (works)

  2. sniffes GRE traffic is properly travel between the 2811 and the pix, but it is passing the PIX unrequited and encapsulated

  3. has changed the mode IP tunnel. Now it's working.

  It seems that the PIX is simply not able to follow the GRE traffic. Everyone knows this?

  Sounds like it could be CSCse36327.

  Did not help "clear the host local a.a.a.a?

  If so, you can upgrade to 8.0 and configure "sysopt reclassify vpn connection.

• FW PIX configuration using PKI on Microsoft Server CA

  I just wanted to know ther was looking for someone out there who has led to private PKI IPSec on a PIX 515ER to CA Server of Microsoft 2 K Advanced Server help. If so, can you please direct me for details of how to implement this? I'm more interested in implementing IPSec with ICP on remote users dial-up (via the Internet) using customer Cisco VPN and ends on a PIX firewall. Thanks in advance for your answers.

  Hello

  Try the following link

  http://www.Cisco.com/en/us/products/sw/secursw/ps2120/products_user_guide_chapter09186a00800898d9.html#1031583

  MS CA server installation is a very simple task...

  a. install network / active directory / DNS / IIS services

  b. then add the CA on the Server service. ensure that u Select Business certification, not stand-alone option... (I also recommend to read a few notes on the MS site of).

  c. once the installation type sequence url on the web browser from a remote PC

  http://certsrv/ - this url will allow you to request and see the status of the certificates...

  I used MS CA servers for a PKI IPsec deployment and it work very well...

  I hope this helps u

  concerning

  with this

• VPN client behind ok asa pix but no asa

  Hi all

  I was faced with a newly installed asa5505 couple. We can use the vpnclient in devices, but not behind another asa. Behind the asa same we can vpn for previous installations of pix. But when we go to other asa installs, we get the regular creation of translation failed for protocol 50.

  We have activated, isakmp, nat-traversal, udp 4500 and udp 10000. If the fault is at the other end, even if the error shows in this end?

  Anyone who is willing to help me with this?

  see you soon / Peter

  You do not allow protocol 50 - ESP through the firewall. The remote end VPN are trying to create a VPN in mode 'Hand' is not "Aggressive" mode as VPN clients.

  Add the below and test again: -.

  permit for outside_access_in to access extensive list of 6 esp a whole line

  HTH.

• Loading of PDM on upgrade PIX 525 pair

  Hello

  Recently updated a pair of 525 s of the PIX to 6.3 (3) running in stateful failover and want to load PDM on them. I have some queries:

  (1) because they are in the production environment, you reload the PIX for PDM work?

  (2) is there a recommended way to install PDM on a pair of live PIX?

  (1) no charging is required.

  (2) the installation is no different. The only thing to note is that you will need mode configuration of the standby firewall that will generate a warning. You can ignore it. When you're done, use [sleep command] writing on the active firewall as a precaution.

• PAT on PIX vs NAT overload on router

  Better question practice...

  It's better to perform PAT through a NAT overload on a router bastion with a static on the PIX instruction or PAT on the PIX configuration uses a global IP address?

  Other alternatives?

  Example of router *.

  Router configuration

  IP nat FirstPAT 172.16.5.100 pool 172.16.5.100 255.255.255.0

  FirstPAT IP nat source list 10 overload

  access-list 10 permit 10.10.10.0 0.255.255.255

  PIX installation

  static (inside, outside) 10.10.10.0 10.10.10.0 netmask 255.255.255.0

  Example of PIX *.

  Global (Outside) 1 172.16.5.100

  NAT (inside) 1 0 0

  Thanks in advance for all the messages!

  In my opinion, there is no real compelling reasons to go with one idea on the other. Probably, I would lean towards leaving the PIX do NAT, but I could be swayed. The reason is that the PIX has essentially already been NAT (all back on the same address). But again, either should be good.

  A suggestion however if you went with overloading NAT on the router would be to do it with a map of the route as opposed to the example of access list you have. Something like this:

  IP nat FirstPAT 172.16.5.100 pool 172.16.5.100 255.255.255.0

  IP nat source map route nat FirstPAT overload

  route nat allowed 10 map

  access-list 10 permit 10.10.10.0 0.255.255.255

  This creates a NAT entry in the NAT table on the router.

  Good luck.

  Scott