Installation of grid with a response file
DB version: 11.2.0.2Platform: Solaris, OEL
We were asked to use a response file rather the installer GUI grid, to make installation of the grid.
The response file is similair below
http://www.orafaq.com/maillist/Oracle-l/2011/08/att-0184/grid_install.rsp
I've not done this before. According to the Oracle Doc, we run something like this.
$ cd /u01/app/grid/crs/config/
$ ./config.sh -responseFile /u01/app/grid/response/response_file.rsp
I noticed that for a setting as below, we are specifying the private and Public IPs of a single node.oracle.install.crs.config.networkInterfaceList
Thus, for a node 2 CARS, what I need to run script in config.sh with the response (with specific values of Node2) fileon the second node separately?
$ ./config.sh -responseFile /u01/app/grid/response/response_file.rsp
Hello
lol Config.sh copies the crs_config.params on both nodes.
However, you will need to run root.sh on both nodes.
Sebastian
Tags: Database
Similar Questions
-
After an Oracle database is installed, a summary screen will appear and the user can save the 'Response' file on the disk.
My question is this: once the database has been installed, and closed the screen above, is it possible to get all the same information again?All settings / names / options you supplied / selected during installation / create are captured in the log file.
However, you cannot 'create' response to this log file. You could put in a lot of effort to extract the information from the log file and compare it with a response file valid install/create one another and then "recreate" the response file "by craft it. You might be missing information that you designate the good response to install/create another file.
Hemant K Collette
-
Create Asm Db using response files
Hello
My first question can create us a database of asm using a dbca.rsp of IE response file.
I managed to install the software of the ASM, only using a response file and settle went very well.
I then configure netca using the response file and who was too perfect.
I then set up asm with the response file using this wizard dbca-silent - configureAsm - responsefile/tmp/dbca.rsp. (I think that this step too went well, however, it does not get start it)
Then used this dbca-silent - createDatabase responsefile - /tmp/dbca.rsp and this option to create a database to the file system.
Thank you...PL see these Docs MOS
744237.1 - DBCA in silent mode with the DSO
437915.1 - how to manually configure the database for the database control and Instances of ASM (Silent Mode)?
402023.1 - how to integrate Createdb appeal with a silent Installation of 10gHTH
Srini -
I'm trying to install Acrobat 8 Standard on a PC with Windows 7, 64 bit. During installation, you asked me to provide 'File PDF.dll Adobe for Windows Vista'. How can I get the required file?
Hi Alan Horan.
This link appears corresponding to your query, please visit this link ( error "the file AdobePDF.dll is needed" |) CS3 | 64 - bit Windows ) and let me know if you face any problem.
Kind regards
Rahul Tyagi -
response file is not created for silent installation
Trying to create a response to a silent installation file. From page 15 of the Installation and the Administration of PDF:
Example: ' < location of the Setup file > \setup.exe "/ r /f1" < location of the answer "
"file > \setup.iss.
Fact that, but no setup.iss after running through the installation. Did a search on the C drive too, but found nothing.
It is for the Developer Version 3.5.1 esp2 PUK.
Our environment is Windows XP Service Pack 2.
Anyone know why the answer file is not created as the directions indicate? Thank you.Hi Jason,
I might have an idea on why it does not work.
When you run setup.exe you see a menu option which indicates that following:
Read me (see the Upgrade Guide)
Read me (see the Setup Guide and Administration
Installation (installation of the Oracle User Productivity Kit 3.5.1...)If so, you need to get out of this configuration. Then in the source (CD-ROM or the location of the installation), browse to the UPKTool folder, there you will see a file named setup.exe, it is the executable that is launched when you click on the button install.
In any case, to create a response file, you will need to run this setup.exe, so when you run at a command prompt, you should have something like this:
/ F1/r 'D:\UPKTool\Setup.exe' "C:\
\setup.iss" I mentioned the C drive instead of drive D because I assume that D is a CD-ROM drive otherwise you can place it on any place.
I hope this helps.
Kind regards
Ray -
Why I don't get a response from the Dept. serial number already contacted them twice with ZERO response. I have included my product code and proof of my job as requested but nowt is back!
Kingussie81 that I saw the account that you used to post on this public forum and your Creative Suite 5.5 Design Premium education serial number is registered under your account at http://www.adobe.com/. For more information on how to locate your serial number registered please see quickly find your serial number.
If you need to download a new copy installation files, they are available to Download CS5.5 products.
-
YES 2.0.1 can a response file save
You can record a response with YES 2.0.1 file or not? I find conflicting information in Google search. Some say v2.2 and above other say v2.0 and above
ORA: 9.0.1 / 9.0.1.4
Operating system: Windows platforms
If it works in 2.0.1 is the chain of command?
installation - save - FichierDestination < response_file_name >
If this is not the case, what is it please. Thanks in advance for your help.
Published by: 911111 on January 30, 2012 13:13Documentation in MOS States that the recording feature is only available with YES 2.2 and higher.
How to create a RDBMS YES Silent install response files. [388451.1 ID]
How to produce the response file by saving during Installation [ID 222402.1]Where do you see references that this can be done Yes 2.0?
Since several years 9.0.1 was around, so don't remember not to much. The 9.0.1 doc install Win also does not refer to the recording mode.
http://docs.Oracle.com/CD/A91202_01/901_doc/EM.901/a88812/RSP.htm#97
HTH
Srini -
password Oracle 10 g in the response file
Hi guys,.
I try to install oracle 10.2.0.1 on solaris using the answer file. The "funny" is that when you set passwords for something like 0RAcle1 (first char is 'zero'). It generates an error:
>
INFO: Definition of variable "s_superAdminSamePasswdAgain" ' * protégés of value, is not to be connected *'. Has received the value of the response file.
INFO: YES - 10155:Error while defining the variable s_superAdminSamePasswdAgain: the password must begin with a character for the user
INFO: Definition of variable "s_superAdminSamePasswdAgain" ' * protégés of value, is not to be connected *'. The calculation of the variable value received.
Selected user: ARRE & installation of this component only.
>
I tried with password in ""or wiothout - same result. "
If I put the same passowrds for a single word, like 'password' Setup works very well.
Are there restrictions on the parameters the password?
Thank you
KidoYes - it's in the doc to install: Pei http://download.oracle.com/docs/cd/B19306_01/install.102/b15690/inst_task.htm#sthref771
Srini
-
Link new installation of thunderbird with the old profile.
I created a new profile and stored on an external drive, there is a certain messages, I just had to reinstall win7 and do not know how to link a new installation of thunderbird with my old profile. Seems fair to get a host of issues that do nothing.
Look at https://support.mozilla.org/en-US/kb/profiles-tb#w_how-to-find-your-profile and then go to the directory corresponding to your external drive to find your old * *.default file.
Copy your old profile to the directory where your current profile is stored.
See https://support.mozilla.org/en-US/kb/using-multiple-profiles to switch to your old GOLD "profiles.ini" edit profile to change the 'path' in the name of your old profile.
Restart Thunderbird. -
Which programs are associated with the xcm files
I found a folder in my folder system program (. 86) that I don't know or I don't know where it comes from. It has a bunch of XCM file in the known folder that cannot open my own computer, can not give me info on how to open and cannot tell me which of my programs, he joined. I want to delete it because it seems that a suspect case, but not because I can not check programs what or how much it may or may not be associated with.
Sincerely yours, Aaron Baker.Take a look at this link:
http://pcsupport.about.com/od/FileExtensions/f/xcmfile.htm
Excerpts .....................................
What is the .xcm file?
Response: A file with the XCM file extension is a Concept exported CmapTools mapping file.
How to open a XCM file:
The easiest way to open a file XCM is double-click on it and let your PC decide which default application should open the file. If no program opens the XCM file then you have probably an installed application that can view and/or edit files XCM.
-
How to restore a flashdrive with its original files that have been replaced or removed?
Original title: how to restore a flashdrive with its original files? I accidentally replaced a file with an earlier version of this file.
Missing file
Hi, David B.Erkens,.Unfortunately, you can not recover the file from the flash drive. You may need to use some third party recovery software to get the file.
Please use your favorite search engine and browse for such a program that is used to.
Note: This response contains a reference to third party World Wide Web site. Microsoft provides this information as a convenience to you. Microsoft does not control these sites and no has not tested any software or information found on these sites; Therefore, Microsoft cannot make any approach to quality, security or the ability of a software or information that are there. There are the dangers inherent in the use of any software found on the Internet, and Microsoft cautions you to make sure that you completely understand the risk before retrieving any software from the Internet.
-
Original title: load error when you try to load Halo 2
People at Microsoft, I have a problem trying to load Halo 2 on my dv7 Paviliaon with Vista and the 2.8 GB Intel Centrino 2 processor. When I try and load the game, I get and error stating: "the files are missing or damaged in the installation directory. A few important files required to run this game are missing from the installation directory. "It bothered me for several reasons. One: the disc that I use is an original disc out of the box so hsould have no problem. Two: the game has been loaded previously on the same computer without apparent problem at the time. It has been deleted (don't remember why) and when I tried to reinstall, the error came. Three: I did as recommended and updated all programs and drivers, nothing works. So my question is, how do I reinstall Halo 2 and what this problem will arise if I decide to buy and load Halo 3?
Thank you for your time in advance.
Hello
As you are facing problems with Halo 2, I suggest you to refer the link for better support:
-
I am trying to charge my cell phone and after all is finished and loads of windows for the first time that he comes up with an error "Windows cannot parse or process unattend [C:\Windows\Panther\unattend.xml] answer file in the answer file is invalid." The error was detected in the column of the row 9 222 of the answer file. "I replaced the hard drive and it wont let me go into safe mode as the installtion is not complete. Any help please
You use an installation with an answer file to configure the system as you wish? If there is a problem with the answer file, then you will need to do a normal installation instead of one without supervision and thus circumvent the answer file. You have the means to do so? How is made installation - on DVD or on a network? You have another program for unattended Setup that you can use or is it only available? Do you know how to fix the error in the answer file if you have access to and can make changes? If you can not enter the system in safe mode or normal mode, the only way is through to boot from a CD/DVD. I don't know if the command prompt on the drive of Installation of Vista will help, but it can be a way to access what is on the hard drive. I don't know what you hope to accomplish with access to the system partially installed in any case. It seems to me you need to do another installation using a NORMAL process, so not to interfere with the answer file. If you still want to participate, here are two options that might work.
If you do not have a disc, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD (using another computer).
You can use Knoppix http://www.knopper.net/knoppix/index-en.html with a good ISO as Copier: http://isorecorder.alexfeinman.com/isorecorder.htm as well as a blank CD (yet once done from another computer. This should give you enough access to the system so you can be able to fix the problem with the answer file (if this will help at this stage - since I do not know how to restart the installation where he had failed. You will probably need to reboot again, but this time you must correct the answer file before you start or do a normal installation without using an answer file.
I hope this helps.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
I lost my CD windows 7 Home Basic, can you provide me with the ISO file
I'm on PC assembled with i3 1st gen 3.07 GHZ processor Intel with 4 GB of RAM.
I put in Windows 7 Home Basic and have the activation key for the same thing but lost my CD. Can you provide me with the ISO files approved for her.
I had tried a lot of ISO file, but none worked mainly for basic Stater of Windows and home proplary. Is the ISO file or my PC is not supported with Home basic.
If Yes, then what is the solution.
Some of the links that I tried are
https://***.to/Windows-7-all-in-one-pre-activated-excellent-t7661549.html
Please help as soon as possible.
For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.
It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.
Given that this option is no longer available, what are your options? See the article for more details:
-
OEM 13 c - problem installation using a PDB as OMR file
I encountered a problem while installing OEM 13 c (13.1.0.0) against a 12.1.0.2.0 snap-in database.
I have a 12.1.0.2.5 RAC DB with a PDB file named "emrep_pdb".
Select name, open_mode from v$ PDB;
NAME OPEN_MODE
------------------------------ ----------
PDB$ SEEDS IN READ ONLY
BWPDB MOUNTED
EMREP_PDB READ WRITE <-I want to use this PDB as my OMR
On the #7 of the OEM Enterprise installation procedure step Manager Cloud control 13 c I enter the following database connection details:
Database hostname: hostname for DB SCAN >
Port: 1521
Service/SID: emrep_pdb
SYS password: < password account SYS >
I get the message:
ORA-01219: connectable to no database or database open; motions allowed in the fixed tables or views only
However, the PDB is opened as shown in the above query. Any ideas why I can't connect to the PDB of the 13 c OEM to step #7 Installer?
Hmmm, it seems that this peut been the problem:
INST_ID select, name, open_Mode, restricted SGS $ PDB;
INST_ID SELECT OPEN_MODE RESTRICTED NAME
---------- ------------------------------ ---------- ----------
2 SEEDS OF $ PDB READ ONLY NO.
2 MOUNTED EMREP_PDB
PDB $1 SEED READ ONLY NO.
1 EMREP_PDB READ WRITE NOT
The PDB is not open on the #2 node. DOH! Thank you.
Looks like I had to specify:
ALTER connectable database to open emrep_pdb instance = all;
I forgot the "instances = all" part.
Maybe you are looking for
-
NoScript is still available in Firefox?
I read on another site that Firefox has a thing called NoScript which would give a user the opportunity, when you go to different websites, to enable or disable Javascript. Now I don't see a NoScript in the settings menus, but only the possibility to
-
I would like a step by step process apple a new airport express with time capsule base of connection (cable cat 5 150 Ft) with late 2008 macbook.
-
problem with the ports of the two SLM2048
Hello:I have a problem with two models of SLM2048.I only as configured in these devices was 4 VLAN and link aggregation port between these devices.I detect some Don t work ports (I connect to a workstation in the port and the Don t upward, but in the
-
Original title: need help please Hello everyone and I hope someone can help me. Necessary to update my java. I deleted all the previous java and tried to download the free java version for Windows 7 @ java.com It acts like it loads then I get a pop u
-
The lost Microsoft 4000 wireless mobile mouse transmitter!
I lost my transceiver "mouse Microsoft 4000 wireless mobile. Can I use my mouse without transmitter/receiver?