Installation of the new firmware?

Similar Questions

• Working Group stopped after the installation of the new wireless router

  My working group stopped working after the installation of the new wireless router.  Router was switched were to move from DSL to fiber optic.

  I have a very simple home with two laptops working group, the two are connected with a wireless router.  A PC is running XP with the updates and service packs; the other PC is Windows 7 Home premium.  This working group was running without problems for a few years.  The Working Group has been used to share files between two laptops.  Internet access was through the DSL wireless router and print was with a wireless printer, without going through the working group.

  I had my DSL set out to free fiber optic last week, which meant that a new wireless router has been installed by my local phone company.  Internet works fine; wireless printer works.  The working group no longer works.  When I try to connect from XP to Win7 and I click on mode workgroup computers, I get this message:

  WorkGroupName is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.

  The network path was not found.

  I tried to create a new working group, the new name for the same workgroup on both machines, but this did not help.  Working groups are supposed to be simple; This seems to be a problem on the new router - telco tech support says that nothing is stuck on the router. I don't believe them.

  What version of XP you use (Home or Pro)?

  Can you access the Win 7 a XP computer?

  You have identical accounts, passwords on both computers?

  If all that was done was to change routers without making any changes on the computers, the most likely cause of the problem is a third party (other than Windows) firewall on at least one of the computers.  Being by default, a router automatically assigns IP addresses to computers on your local network.  Different brands of routers, but use different address ranges.  For example, Cisco/Linksys routers typically use the 192.168 form addresses. 1.1 with 192.168. 1. 254, while the D-Link routers typically use 192.168.1 to 192.168.0.0. 254.  A firewall configured to allow only the first IP range blocks communication to the scope of the latter.

  So... What is the name and version of your anti-virus program?
  What other security software is installed?

  On every laptop computer, open a command prompt window
  for XP: start > run > cmd > OK
  for Win 7: type cmd.exe in the search box and press enter
  In the black command prompt window, type the following command and press enter
  ipconfig

  Please provide the values for the following for the adapter wireless of each computer
  IP (XP)
  IPv4 address (Win 7)
  Default gateway

• The new Firmware...

  Well... I downloaded the new firmware three times and it still doesn't work. What is happening is: I click on the icon (I put it on my desk), he asked me "do you want to run this file? I click on "Run" and the box that opens goes and nothing happens after that. He worked on the first download with my mp3 player. I have a Sansa clip and I had no problems with it until this week. What happened was: I turned it on and it works normally, it seemed, I chose my song, I wanted to listen to and carried on with what I was doing and then it off suddenly. I know that the battery was not dead because I had loaded this day here so I walk back and the Database "Refresh" came so I just went back for the song I was listening to - AND THE IT TURNS OFF AGAIN. So I try to turn it on, it going off, turn it on, it turns off. Finally, it no longer lights. Can I go online to do some troubleshooting to see what the problem was and I've saw that Firmware was supposed to help-so I did a security scan to make sure it was safe for my computer and started to download. As I said, the first time, I downloaded the software that it worked very well. But he said that I had to clear 6 MB of free space on my camera - I did everything what I deleted still shows up on my device so that I could not download the firmware, then I just gave up with it because I've had enough with it does not properly. Sansa never gave no problems so far. Is this the end for my mp3 player? I need to know if I can invest in something else.    Thank you.

  The original video had problems with bad Soldered joints on the battery terminal wires. Sorry to say, this is what it looks like happened to yours. If you are adventurous and handy with a soldering tip fine iron (or know someone who is) you can probably fix it.

  You can Google "dismantling the Sansa Clip" and find all kinds of Youtube videos and other pictograms on the way to get it out without damaging it and put it back together. Otherwise, I fear that it is ruined; transfer the files out of it (as long as it always connects to the computer) and get a new player, maybe a Clip + or Zip if you like the small size and as a bonus, these new players have a SC slot to expand memory.

• Please refers to the path of the new firmware

  This message keeps poping up ("Please designate the path of the new firmware") when I try to update the firmware on my router WRT110 wireless, even if I used the button BROWSE to select the new .bin firmware file.

  Someone has an idea to solve this problem?

  MB

  Have you tried another browser to update the firmware? How about you try it on another computer? If the two do not work, try to power cycle the router (unplug the power for two seconds) then once the power led is solid, try the update again. If the update will still not proceed, reset the router by pressing the reset button on it by using a PIN or a paper clip for 30 seconds. It shut down again for another couple of seconds. Once the power led is solid, try the update again.

• How the new firmware of tftp to wag160n?

  Hello

  My WAG160N has same problem as described in this post from xellmon

  http://forums.linksysbycisco.com/linksys/board/message?board.id=DSL&thread.id=9859 .

  The cancellation of my warranty but new. (void warranty in a storm). Desperately trying to resurrect WAG160n.

  Details of the device

  Annex WAG160N has

  Firmware 1.00.10

  Is it possible to new firmware tftp in the unit?

  If so, how the new firmware tftp?

  what firmware file I need to download?

  Thank you

  Download the firmware for Annex WAG160N has... Try this link and check if it works... If this isn't the case, then, you need to replace the router.

• Problems with the new firmware 0.1.E.1.4

  Hello

  After the last update, my phone (Samsung Galaxy S3) has problems with his phone for headset support.

  I can only use the headset as headphones to phone for calls. Do not go with general audio profile.

  Sometimes I can connect audio but it disconnects quickly.

  It is a very serious problem that needs to be fixed, but I doubt that Sony will be releasing a fix quickly.

  So, how do I go back to the previous firmware? (0.1.D.0.6)

  With this firmware, I had no problem. The new firmware has a significant improvement as long as Visual but the helmet doesn't help...

  I need help. Thank you.

  OK, I just do a downgrade.

  I did a factory Reset on the helmet, downloaded "Update Services" and the program tells me that there is an update available, after the update has been completed I'm back on 0.1.D.0.6!

• Cursor not moving/working after the installation of the new keyboard

  I just finished replacing the keyboard on my HP G72 due to spill water on the keyboard a few days ago & some keys no longer work after laptop parched. However, I find that things are not as they should because I can't get the cursor to move. I do not use a mouse & rely on the touchpad. I tried to remove the keyboard & reinstall several times but all about no. avail & wonder if anyone can give me some advice, even if it is the keyboard itself may be defective & I need to buy a new one. I don't want to just assume there is a problem with this new keyboard only to discover that the problem is somewhere else & that there is other things I should be doing or trying.

  I had to install a new keyboard on this computer laptop sometimes last year afer having a similar accident with the flow of the water, but the installation of the new time was pretty much a piece of cake, I followed the guides on the screen, I have been looking & everything was perfect, once I had installed the new keyboard.

  Thank you if you can advise.

  Hello

  If possible, try a USB mouse for awhile. This way if the slider works, you can try reinstalling the drivers for the touchpad that could solve the problem. If the cursor does not work with an external mouse also then the problem could be hardware related.

  Sometimes to repeat the installation process of the keyboard all over again also helps.

• Adobe Premiere Pro requires new mac operating system. My Adobe programs already installed would work after the installation of the new operating system?

  Hey there,

  I think to get the Premiere Pro, which requires that the new Mac operating system. But I installed the other Adobe programs such as Photoshop, Indesign etc years ago.  These work on my current operating system (= Mac OS X 10.8.5).) Anyway, now I wonder if my programs already installed Adobe might work after the installation of the new operating system.

  Any ideas what to do?

  Thank you very much.

  Yes, they will work in the new OS.

  Kind regards

  Hervé Khare

• error 0x0000007B (0xf78a2524, 0xC0000034, 0x00000000, 0x00000000) after the installation of the new RAM

  I get the BSOD when booting with the STOP: 0x0000007B (0xf78a2524, 0xC0000034, 0x00000000, 0x00000000) message. The computer is a Dell Dimension 8400. I installed the new ram to find this message and we tried him swinging back the RAM on the former with the problem still persists.

  Hello

  Very good chance you loosened a cable or connection when you replaced the
  memory.

  Check with Dell Support, their drivers and documentation online and ask in the Dell
  forums for known issues.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/
  ================================================================

  Check the disk for malware:

  Create a Bootable CD with the Trinity Rescue Kit - free - which comes with 5 antivirus programs
  Integrable Hirem is another choice - more can be found using Google.

  Trinity Rescue Kit - download on top right of the page
  http://trinityhome.org/home/index.php?wpid=1&front_id=12

  CD of Hirem boot is another good choice
  http://www.hirensbootcd.NET/Download.html
  http://www.hirensbootcd.NET/CD-contents/138-HBCD-111.html

  ===================================================================

  You can also save the data and re-install Windows 7. The hard drive can be set
  another computer as a 2nd drive (the best) or in an external USB enclosure. Either would allow
  allows you to copy the data to removable media such as CD, DVD or other USB drives.

  Or you can use a boot Ubuntu CD to back up data.

  Use Ubuntu Live CD to backup files from your Windows computer dead
  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windows-computer

  ===================================================================

  For slightly more:

  BCCode: 7B 0x0000007B<-- read="" this="">

  INACCESSIBLE_BOOT_DEVICE bug control has a value of 0x0000007B. This bug check indicates that the Microsoft Windows operating system has lost access to the system partition during startup.

  Important information if you have received a STOP Code

  If you have received a blue screen error, or stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer connect with Support.

  If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

  The following actions could prevent a mistake like this does not happen:

  1. Download and install updates for your computer from Windows Update device drivers.
  2. Scan your computer for computer viruses.
  3. Check your hard drive for errors.

  Cause

  Bug INACCESSIBLE_BOOT_DEVICE control often occurs due to a failure of the boot device. During the initialization of the I/O system, the boot device driver could have no initialize the boot device (usually a hard drive). Initialization of file system may have failed because it does not recognize the data on the boot device. In addition, repartition the system partition or installing a new SCSI adapter or disk controller could encourage this error.

  This error can also occur because of incompatible disc material. If the error occurred in the initial configuration of the system, the system have maybe installed on an unsupported drive or a SCSI controller. Some controllers are supported only by the drivers that are in the library of drivers Windows (WDL). (These drivers require the user to perform a custom installation.)

  
  Resolution

  This error always occurs during the startup of the system. This error often occurs before the debugger connection, kind of debugging can be difficult, if not impossible.

  Fix a defective boot device: If a boot device is at fault, you must change the boot options. For more information changing these options, see Software Configuration on the target computer.

  Solve a problem of incompatible hard disk: If the installation program automatically detects the controller, you may have to skip the detection and the disc of the specific manufacturer allows to load the driver. Also, check the availability of updates for the firmware of the system BIOS and SCSI controller. Updates of this kind are usually available on the website or BBS of the hardware manufacturer.

  Delete all material recently added, especially of hard disks or controllers, to see if the error is resolved. If the problematic material is a hard drive, the firmware version of the drive may be incompatible with your version of the Windows operating system. Contact the manufacturer for updates. If you have removed another material element and the error is resolved, conflicts of port IRQ or i/o likely exist. Reconfigure the new device according to the manufacturer's instructions.

  Confirm that the hard disk drivers, hard disk controllers and SCSI adapters are listed in the list of the products tested Microsoft Windows market.

  If you have recently added a driver, restart your computer, and then press F8 to character-based menu that displays the choice of operating system. In the menu of Advanced Options , select the last known good Configuration option. This option is most effective when you add a single driver or service at a time.

  In addition, check your computer for viruses using any update, commercial software that examines the Master Boot Record of the disk hard antivirus. All systems of Windows files can be infected by viruses.

  This error can also occur due to corruption of the hard drive. Run Chkdsk /f /r on the system partition. You must restart the computer before the start of the analysis of disk. If you cannot start the computer due to the error, use the Recovery Console and run Chkdsk/r.

  If you cannot start the system in the last known good configuration, you should try to boot from the Windows CD. Then, you can run Chkdsk from the Repair Console.

  Warning   If your system partition is formatted with the FAT file system the long file names that use the Windows operating system could be damaged if you use Scandisk or another MS-DOS-based disk tool to verify the integrity of your hard disk from MS-DOS. Always use the version of Chkdsk that matches your version of Windows.

  If your system has SCSI adapters, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination. For IDE devices, define the IDE port integrated as primary only. Also check each IDE device for setting good master/subordinate/stand alone . Try to remove all IDE devices except for the hard drives. Finally, check the system log in Event Viewer for additional error messages that might help identify the device or driver that generated the error.

  BCCode: 7B 0x0000007B<-- read="" this="">
  * 1138.html? order = votes http://www.faultwire.com/solutions-fatal_error/Check-for-viruses-on-your-Computer-0x0000007B-

  =================================================================

  If you do not have a Windows 7 disc, you can borrow a friends because they are not a copy
  protected. The manufacturer of your system will also sell the physical DVD cheap since you already
  Clean Windows. You can also do an ERD on another computer.

  Try the Startup Repair - (if at anytime, benefit you from some, but not full access coming to Windows
  return and then try to startup repair.)

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  Try the disk Options recovery or Windows 7 startup repair.

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  Also from the command PROMPT on the Console (if possible) recovery or a Windows 7 disc

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  Retry After Chkdsk startup repair.

  If after those you can try the system restore to fashion without failure or the valuation or Windows 7
  disc.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  --------------------------------------------------------------------

  If you need to repair disks - these help repair Windows not re-install.
  Often an ERD will help you when the recovery disk is not - use OPTION 2 to
  make the disc.
  
  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  ======================================

  If necessary:

  What to do if Windows does not start correctly
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-Windows-wont-start-correctly

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials

  I hope this helps.

• Can not get the new firmware to "take".

  I am trying to install rockbox on my brand new Clip + - the problem of "Refreshing your media" bit me once I copied 15 GB of my old MP3 player on a new uSDHC card.

  However, no matter what I do, I can't get the player to update its firmware.

  I used rockbox Setup both a manual installation. The fw file is in the root directory of the element, which is in MSC mode, but as soon as I log out, instead of the promised update firware followed by a stop, I simply get "Refreshing your media" and then the player stays on indefinitely.

  Someone at - it ideas? Am I missing something? The player would be defective?

  I think randomly would be that you are trying to Flash the incorrect firmware for your device. Each device will only accept firmware designed for it, in order to avoid destroying the player by the incompatible firmware flashing.

  What is the version number on your player and the name + the version of the firmware file you are trying to flash?

• How to share tabs between my various Firefox installations using the new system of accounts of Firefox?

  I use Firefox Nightly (2014-02-18, 30.a1, x 64) on my laptop (Windows Pro 8.1 x 64) and I was using Firefox Beta on my Nexus 5 (Android 4.4.2). Recently, Mozilla announced the new system of accounts of Firefox (which replaces the old Firefox Sync account) and I created an account of Firefox for my computer laptop installation every night. Because the new account in Firefox does not work with the old Firefox Sync account, I replaced my installation Android of the beta version of Firefox with Firefox Nightly and signed account Firefox on my Android. However, when I try to send a tab of my Android installation to my installation of laptop using intend to 'Share for every night', every night asking me to implement a sync account, which is impossible to fill in my computer laptop system every night. I tried to replace my Android installation every night with an Android Aurora facility, but the same problem occurs.

  What's worse, is that even with my laptop and Android facilities signed on the same account in Firefox, I'm not all information is synchronized between 2 facilities. No story is shared, and I don't see the list of tabs opened from the other device. I can't move tabs between my phone and my laptop, which is something I've used every week I visited websites and read that my RSS FEED on my phone. Does anyone know how to share tabs using Firefox's new accounts? Does anyone know why Firefox accounts doesn't seem to be synchronization of data between my 2 installations?

  Hi gfactor:

  An update on this issue. I think that this (965811) was fixed in Firefox Beta 29.

  Please try beta if you have some time (just search for Firefox Beta on the google play and then install firefox beta) and let us know if Firefox 29 beta sendtab now works for you.
  

• HP T610 more: HPDM deployment for t610 image more crashes during the installation of the new initial start of the image

  We are working on the update of our thin clients HP T610 more.  Update us the thin clients in the last image of the OS WES7P and also update to IE11 and Citrix receiver 4.4.

  We use HPDM 4.6.4

  We have successfully several T610s and update the image of the OS and related software with no problems.  We are then able to use the 4.6.4 to successfully shoot HPDM and image of these thin clients updated in the master repository.

  We then create a task to deploy the new image to several thin clients.  We configure the task to use the imagery being cached, and then run the task.  HPDM then successfully deploys the image for thin clients.

  Customers accept the image cache and once the image is fully downloaded they restart to deploy the image.   After the restart, the image unfolds and decompresses correctly, then the thin client, start the original installation of Windows.

  But for 90% or more of these newly imaged thin clients that they get hung up during the installation of Windows (usually during the message that windows is written to the Registry).  Once the thin clients get hung at this stage they are inaccessible and unrecoverable by HPDM and must be copied via USB.

  We believe that the issue is somehow related monitors are connected to thin clients.  If isolate us completely thin clients monitors, then deploy an image the new image is OK.  HPDM reports that the image has been deployed successfully.  If we then go back to thin clients and reconnect the monitors of the thin client is updated and the screen seems to be in standard vga mode low resolution.  A restart of the thin client then recognizes and sets the appropriate screen resolution, and the thin client is good to go.

  What is normal sound monitors must be separated to deploy a new image?

  Thanks for any idea or thougts.

  From the point of view HPDM, disconnect monitor is not required when you deploy the image. Personal thought is that there is a compatibility problem between the display driver, graphics card and the system. Installing Windows intend to write a default registry value based on connected monitor (maybe display settings), for some reason, he was stuck. I'm not the driver or the operating system that you are an expert, I would say that you submit a ticket to HP for additional troubleshooting.

• Problems with the new firmware

  New firmware called my books podcasts and mixed together books and podcasts.  Podcast alley section. Also fails to player.  Firmware has screwed my player. Need help please, I have a sanDisk Sanasa fuse + MP3 player and latest firm ware (today).  Thanks in advance.

  The first time that you access the books, it's confusing, but take a look on all small three points at the bottom of the screen after you type the central point.  This reveals that there are three screens partitions via slide to right or left on the touch screen.

  To navigate between the choices, some books with a single tap Center, then sweep right or left to go between Audible / books / Podcasts.

  Do you like the new LOCK feature?

  I just made the connection, your name reminds me of Benjamin Vandervoort, played by John Wayne, in The Longest Day.  He served with distinction in Holy Mother Church.

  Bob

• EA6500: What changes or improvements of the new Firmware offer?

  I just connected to two of my three routers EA6500 and noticed that they have new firmware: 1.1.29.162351. This new version gives anything of note... or... did some minor changes?

  See the release notes for the update here:

  http://support.Linksys.com/en-us/support/routers/EA6500

• I have updated to the new firmware, cannot connect to WVC54GC

  Hello

  I update my WVC54GC (V1.1) with the latest firmware from the site (ver 1.26), when the update is complete, blue Led restart, I stoked market once again, but I can't connect to the camera, I have reset, same problem, the led flashes blue awhile then drove on continious, I try to connect with the software (search for camera) and with the browser to the default IP address : 192.168.1.115, nothing...

  Maybe something wrong during the download of the firmware.

  How can I go back to the old firmware? is that their another method for hard reset it (other then on the reset button on the side)

  Thank you to for your advice.

  I solve this problem (after reset the cam for 30 seconds), all settings became as default, including the IP address are set to: 192.168.1.115

  I connect to my PC directly via the cable to the cam, so I changed the configuration of the network card in my PC to:

  IP: 192.168.1.5

  Mask: 255.255.255.0

  Gateway: 192.168.1.115 (this is the IP of the Cam)

  By this solution, I was connected directly to the cam, and I've reconfigured the settings; WiFi, new Ip,... then when I restarded the Cam; all future returned and the cam worked as before (I have not find otherwise with the latest firmware date V1.26 Feb 2008, I had before V1.21 date 2006).

  The funniest thing I bought the cable connection (reverse connection) Ethernet, and when I finished the configuration of the cam, I tried the standard cable (straight): this work is too, so you can use the standard Cam ethernet cable.