Installation of VMWare 6 on IBM Blade Server

Similar Questions

• VMware ESXi on Hs23 IBM Blade Server

  Hi all

  IM facing some problems installing ESXi on my servers blade of HS23E, it gets stuck in the middle of the installation, for the most part on TG3 modules, is there anyway I can get this settled, is there a tool like ServerGuide for installations of VMware?

  Yes, it's just a standard ESXi image with some extensions of the IBM hardware management and driver updates preinstalled. Many other providers of material such as HP and dell offer these images. Since the side VMware it makes no difference if you have installed your guests with these images or image of vanilla from VMware.

• Installation of VMware ESXI 6 in my server

  Hi all

  I have a server that I have configured with raid 1 using the disk on the Server utility.

  When I try to install VMWare ESXI on the server, in the part of the selection of the disk to install the ESXY appears only the physical disks and not the virtual drives configured in table mode. What should I do?

  Concerning

  Milton Aguiar

  You are probably using some (aka 'false') 'software' edge RAID controller. These controllers require additional driver software to work. However, VMware supports only the real hardware RAID controllers, which are transparently logical volumes to the OS. Unless your hardware provider offering dedicated to ESXi drivers (HP as much I know as fact for some of theit controllers of Type B) you may not use the RAID on board.

  André

• Reference Dell M1000e Blade Server

  Hi all

  We have Dell M1000e Server Blade, 13 3 full height and 10 low-profile, I/O switch servers are A1, A2 B1B2 are MXL blade switches and C1, C2 are Brocade Fiber switches.

  mid-height servers are M630 PowerEdge Blade Server

  with 1. Port double QLogic 57810 - k 10 GB

  2 QLogic 57810-k dual port Mezz 10 GB KR ANC card for M-Series Blade servers

  3 Emulex LPM16002 Fibre Channel i/o Card 16Gbps

  and full height blade PowerEdge M820

  1 Broadcom 57810-k Dual port 10 GB KR

  2 Emulex LPM16002 Fibre Channel i/o Card 16Gbps

  the problem is when you first start, we received this message for full height only servers

  "A fabric mismatch detected for B1 Dell Blade mezzanine card"

  and full height servers only does not illuminate they keep flashing red

  What is the problem?

  It looks like the Emulex on the M820 may be installed in wrong mezzanine card. 1 to 3 media fabric C mezzanine card slots. do you know which slit it is currently installed in? Here is some additional info on removal and installation of the mezzanine cards.

  http://Dell.to/2bZ7Ohl

• the application could not start because the configuration of the incorrect application of reinstallation of the application can solve the problem by Insalling Vmware tools so that windows server 2003

  the application could not start because the configuration of the incorrect application of reinstallation of the application can solve the problem by Insalling Vmware tools so that windows server 2003. PFA

  Ranjana,

  Please, review the vminst.log file located in % TEMP and see if we could see related errors.  Otherwise follow the troubleshooting steps below;

  1. check that the guest operating system that you want to install VMware Tools is fully certified.

  2. check that the correct guest operating system is selected

  3. check that the good ISO image is loaded. For more information, see ensuring good ISO image VMware tools is loaded (1003910).

  4. check that the VMware Tools ISO image has not been damaged. For more information, see determine if your VMware Tools ISO image is damaged on a host ESX/ESXi (1004820).

  5. If you are installing a Windows operating system, make sure that you do not encounter problems with your Windows registry database. For more information about the resolution of the problems of register with VMware Tools, see Impossible to upgrade the existing VMware tools (1001354).

  6. If you install on a 64-bit Linux guest OS, make sure that there are no missing dependencies. For more information, see Tools from VMware install fails to start the daemon of guest OS on the operating systems 64-bit Linux with the glibc-common package 32-bit installed (1023185).

  If your problem persists, please refer to: KB VMware: VMware Tools installation problems that are defective in a guest operating system or contact support.

  ~ dGeorgey

• VMware Tools for FreeBSD using Server 5

  Hello

  We run VMware Server 5 and I installed a RELEASE of FreeBSD 8.2 Guest 64-bit on the system.

  I'm trying to locate the installer of VMware for OS tools, but I can't find it anywhere.

  The vmware-tools cd that goes up is only for Linux and not * BSD.

  I have Google would be like crazy, but couldn't find anywhere to download the edition of FreeBSD.

  Could someone point me in the right direction?

  Thank you

  You have the Version/OS invited under change the settings from-> Options tab-> General Options on FreeBSD? If this isn't the case, that's maybe why you get bad VMware tools.

• Cannot complete the installation of the agent vCenter Converter on server %. Error code 1 603

  I have attemptred to convert a Server Windows 2000 Server SP4 on a server of VMware ESXi 4.1.

  I started the process of a PC Windows XP running VMware converter-all-4.3.0 - 292238 and I got the error "could not complete the installation of the agent vCenter Converter on server %. Error 1 603 "code.

  Read in the forums, it seems that the correct version of VMware Converter Standalone is up to 4.1: is this correct?

  To solve the problem, I installed VMware converter standalone 3.x on Windows 2000 box, but I don't think it's the best choice.

  Can someone please help understandiong what is the proper way to convert a Windows 2000 Server?

  Concerning

  Marius

  Faced with the same problem.

  Solution: manually install the agent of vmware converter on the machine that you want to convert. Choose install Cusotm and only install the agent (client or server)

  See you soon

  Swap

• Installation of VMWARE

  Hello Nicolas,.
  
  I'm opting for the installation of VMWARE for PeopleSoft. I'm asking you to confirm if I download the good times...
  
  All of the following conditions are edelivery.oracle.com...
  
  We have the following of the Oracle Media Pack v3 VM2.1.0.0.0...
  
  Oracle VM server 2.1
  Source of Oracle VM Server 2.1
  Oracle VM Manager 2.1
  
  (1) should I all the above or just the Oracle VM 2.1 server and is the version ok that it is supported by Peoplesoft?
  
  (2) the Question is do I really need Cygwin (XClient and NFS) as directed by your blog...? I have the NTFS file system on my machine and the config is the next MS Win XP Prof SP2, 2 GB of RAM and hard disk of 120...
  
  Help appreciated
  Thank you

  "... You cannot use a SCSI CD-ROM drive as a boot device. If you intend to boot from the CD-ROM drive, please plug it like an IDE drive. »
  How to set the CD-ROM drive in your virtual machine settings? Try to set it as IDE(0:0).

  Nicolas.

• Configure the interface service user using IBM HTTP server

  Hello
  
  I do an install of the 9.2.1. WebSphere has been used as the application throughout the installation server. When I go to set up the user interface services (web analysis etc.) I have to enter the location of the IBM http server. However, I do not know what file to use. I also heard that it is a separate installation?
  
  I'd appreciate any help.
  
  Thank you
  
  Nathan

  Hello

  I think you need to install the IBM http server before configuring, you can download it from http://www-01.ibm.com/software/webservers/httpservers/

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• Satellite A660 - 11 M WLan cannot be used after the installation of vmware 3.1.1

  I have a problem with my new laptop Satellite A660 - 11M.

  When I use some VM install VmWare Player 3.1.1 the wireless doesn't work anymore.
  When I push the button to activate the wireless, the led does not illuminate and the FN + F8 key said that the wireless is not enabled.

  I tried to uninstall VMPlayer, but the rest of the problem.
  I also tried to reinstall the Wlan driver.

  Only if I ask a recovery point before the installation of vmWare are all ok.
  You have an idea about the problem?

  Thank you

  Hello

  I know that this question. the VM (virtual machine) is NOT compatible with the Toshiba Flash Cards Support utility.
  The virtual machine affect the functionality of the FN buttons.
  Therefore, delete this system in order to use the FN keys.

• Between R2 2012 Windows and IBM Http Server SSL connection failed periodically.

  Hi, I have a problem recently. I found that my windows server 2012 R2 has sometimes failed to connect with IBM Http Server ssl. Here it is the information of the two servers:

  1 windows 2012 R2

  -Already activate TLS 1.2 and TLS 1.0

  -Already the latest version of windows update and restart

  IIS - 8.5

  2 IBM Http Server

  -Apache 2.2.31

  -using OpenSSL 1.0.2f

  -Allow TLS1.2 and TLS 1.0

  I also captured network traffic when the two server. If the ssl connection has managed to create. Traffic will be like the following screen:

  

  If the ssl connection was impossible to create, network traffic was like the below:

  

  You will see that the ssl connection failed when the version of the TLS protocol was passed to TLSv1. And returned access denied.  The details of the access denied was like the below:

  

  As the captured screen reproduced above, you will see that the SSL for Client Hello was TLSv1.2 but running on the recording layer TLSv1. this Hello customer was sent by the server r2 windows 2012. I don't know why the ssl connection has been passed to TLSv1 suddenly.

  I found that Microsoft has released an update on January 12, 2016. This fix is the resumption of SSL. Update ID was 3109853 , but I have already applied this update on my server. I tried to do the with the other type of server ssl connection, the ssl connection is possible in a stable condition and has happened the problem I mentioned. Is there someone met this case and resolve it finally?

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Can I use IBM HTTP Server as Proxy for WebCenter content?

  When I worked in development, I used Apache 2.2 as a Proxy for WebCenter content.

  I would use the WebLogic Server plugin 'mod_wl_22.so' in Apache to redirect the request of WebLogic.

  In Production, I need to use IBM HTTP Server (IHS) as a proxy.

  I couldn't find any plugin WLS for IBM HTTP Server.

  When I looked at the note of support Doc-ID 1111903.1 , it does not included of IHS in the list.

  This means that IHS is not supported as a proxy for WebCener content?

  If not, can someone tell me where I could download the plugin, please?

  I tried to use the same configurations for Apache 2.2 to the IHS.

  Startup is fine, which means that IHS could load the module 'mod_wl_22.so '.

  But I got error 403 for the connection.

  I couldn't see any access connected the WLS, so I guess that the connection failed introduce to the IHS.

  Any suggestion, please?

  If you want to use for the work of pure http proxy that I don't see why it wouldn't work. However, I didn't a study on this specific topic. However, you may need to do more things manually in the configuration box, and it cannot be officially supported. The unsupported part is often a point where I suggest you use another product that is supported.

  Kind regards

  Johan.

• installation of vmware workstation 6.5 on windows 10 error

  After you install vmware workstation 6.5 on windows 10 it gets error and restart. Is vmware workstation 6.5 support windows 10? FAILED TO INSTALL. vmware workstation 6.5 on windows 8, 8.1 and 10 support. ALL SUPPORT. I still don't understand...

  VMware Workstation 6.x do not support Windows 10 and will never support Windows 10.

  VMware Workstation 6.x reached "end of support" four years, October 1, 2011: Matrix.pdf product lifecycle

  We produce updates for release until its date of "end of support".  A product may not work properly with host OSes, processors or comments OSes that are not compatible with the product, especially the things that have been published after the date of "end of support".  We put a huge amount of effort to ensure that new hardware and operating systems works with each new major release of VMware Workstation, but we cannot go back and update any previous version of product to add support for all hardware and operating systems more recent.  If we tried to do this, VMware Workstation cost much more that it is today, simply because of the amount of work required to maintain!

  You need to upgrade your installation of VMware Workstation to something more recent, or downgrade your host operating system to a version compatible with VMware Workstation 6.5.

  I hope this helps!

  --

  Darius

• Selection of the method of Installation of VMWare Fusion 7

  So I take an edx online course: Introduction to computer CS50x. I am following the installation of VMware Fusion instructions found at the following link: https://manual.cs50.net/appliance/2014/fusion/

  I followed the instructions in step #4: I double click the icon of VMware Fusion. I clicked on 'Open' when prompted. I typed my administrative password. I accepted the license agreement. I inserted the license key. I am now in the window "select the installation method. But herein is the problem. I do not know what installation method to choose, and there are no instructions on it. My options are: (1) import of disk or image; (2) import existing PC; (3) install OS X from the recovery partition; (4) import a virtual machine existing; (5) installation of Boot Camp. and (6) create a custom virtual machine.  There are no instructions or advice to navigate through these options.

  Assistance would be greatly appreciated.

  From what you have posted, it seems to me that the merger has been successfully installed. The dialog box "Select installation method" you see is Fusion trying to be helpful and you guide in the creation of your first virtual machine.

  At this stage of VMware Fusion and eject the mounted disk installation image (so that you do not open the installation program when you must open the copy installed on your disk). Continue to step 5 to download your virtual appliance of the format .ova.

• Installation of VMware in VMware Player tools

  Hello

  I installed VMware Player v7, created a virtual machine (Windows) and wanted to install the VMware Tools via Player > manage > install VMware Tools... but nothing happens when I click on this option. The following 2 other methods I found in a Ko do not work either:

  • Enter D:\setup.exe where D: is the first CD-ROM drive configured for your virtual computer = > NOK as the virtual drive does not show the VMware tools.
  • Looking for the ISO file in the installation folder = > NOK: there is no ISO file.

  After searching on the forum, I realized that VMware Player doesn't come with VMware tools and workaround I used was to install VMware Workstation without a license on another computer, find the file "windows.iso", copy it to the computer, mount it as a virtual drive and start the client installation.

  The thing I don't understand is the reason for which the option is available in the VMware Player menu if the VMware tools are not? It's very confusing for people new to VMware and only install VMware Player...

  You need not download VMware workstation to get VMware Tools in VMware Player!  VMware Player 7 is working fine on my system and had no problem downloading VMware tools, so maybe it's a problem specific to your environment/system that may block recovery.

  Take a look at my answer: Re: VMware Tools missing in the Installation of VMware Player 7