Reference Dell M1000e Blade Server

Similar Questions

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference Dell M610 Blade... Disk failure RAID1, spare disk 0:0:0 always showing in offline mode

  My understanding is that the replacement drive should have developed as ready... don't know where to go.

  SAS 6/iR integrated (Embedded) controller
  ID: 0:0:0
  Status: critical
  Name: Physical disk 0:0:0
  Status: offline
  Supply status: not Applicable
  Bus protocol: SAS
  Media: HDD
  Device remaining life: not Applicable
  Predicted failure: No.
  Review: 5701
  Driver version: not Applicable
  Status of device of life: not Applicable
  Model number: not Applicable
  Certified: Non Applicable
  Encryption Capable: No.
  Encrypted: Not Applicable
  Progress: Not Applicable
  Mirror Set ID: Non Applicable
  Capacity: 136,88 GB (146968412160 bytes)
  RAID disk space used: 136,23 GB (146278862848 bytes)
  Space disk RAID: 0.00 GB (0 bytes)
  Hot spare: No.
  Vendor ID: FUJITSU
  Product ID: MBE2147RC
  Serial number: D310PB600R7Y
  Part number: not available
  Negotiated speed: 3,00 Gbps
  Measuring speed: 3,00 Gbps
  The device's write cache: not Applicable
  Manufacturing date: not available
  Week of manufacture: not available
  Year of manufacture: not available
  SAS address: 500000E1180B1492

  ID: 0:0:1
  Status: Ok
  Name: Physical disk 0:0:1
  Status: online
  Supply status: not Applicable
  Bus protocol: SAS
  Media: HDD
  Device remaining life: not Applicable
  Predicted failure: No.
  Review: D906
  Driver version: not Applicable
  Status of device of life: not Applicable
  Model number: not Applicable
  Certified: Non Applicable
  Encryption Capable: No.
  Encrypted: Not Applicable
  Progress: Not Applicable
  Mirror Set ID: Non Applicable
  Capacity: 136,63 GB (146699976704 bytes)
  RAID disk space used: 136,23 GB (146278862848 bytes)
  Space disk RAID: 0.00 GB (0 bytes)
  Hot spare: No.
  Vendor ID: FUJITSU
  Product ID: MBE2147RC
  Serial number: D304PB70DD5M
  Part No.: PH0W328K7557117EC0WJA01
  Negotiated speed: 3,00 Gbps
  Measuring speed: 3,00 Gbps
  The device's write cache: not Applicable
  Date of production: 05
  Manufacturing of the week: 29
  Manufacturing year: 2011
  SAS address: 500000E1180F8D32

  Restarted the SAS6/iR Perc controller BIOS and realized that there is another BIOS RAID, with little much the only option being to 'Resync '.  Who, after selecting, the resynchronization complete successfully an hour later and everything was OK.

• Reference DELL Blade - Ethernet Passthrough with ESX 4

  I have an environment DELL M1000e blade with M610 and M710 servers.  Running all ESX 4.

  Fabric A1: M6220 (the user's LAN Segment)

  Fabric A2: no

  Fabric B1: Ethernet Passthrough (iSCSI to DELL Equallogic PS5000e SAN)

  Fabric B2: Ethernet Passthrough (iSCSI to DELL Equallogic PS5000e SAN)

  All blade on ESX servers see the A1 and A2 as vmnic0 & vmnic1.  If I understand correctly, the M6220.  The problem is that none of the blades see Passthroughs Ethernet which are connected to a Cisco 2970 switch.  Shouldn't B1 & B2 appear on vmnic2 & vmnic3?  It does not show on the side of ESX.

  Any agency with experience with this would be useful.

  Thanks in advance.

  (1) chassis management controller can tell you what is installed.

  (2) Yes, you do.  If you want to connect to what in fabric B, each server needs to connect to fabric B need a Mezz card on fabric B.

• Reference Dell m6220 aggregated at Cisco 6506

  I transition my old 1955 Dell blade chassis to my 'new' Dell m1000e blade chassis to the House and I encountered a problem. I'm posting in the network as it is more closely related to one than the other available categories.

  Setup: Dell m1000e with six stand-alone m6220 passes (not stacked) connecting to a Cisco 6506. Each m6220 spans four Gb blades in the 6506... M6220-a1, port 17, plugs into 6506, port g1/1; M6220-a1, port 18, plugs into 6506, port g2/1; M6220-a1, port 19, plugs into 6506, g3/1 port; M6220-a1, port 20, plugs into 6506, port g4/1. M6220-a2, port 17, plugs into 6506, port g1/48; M6220-a2, 18 port, connects to 6506, port g2/48; M6220-a2, port 19, plugs into 6506, g3/48 port; M6220-a2, port 20, plugs into 6506, g4/48 port; the process repeats supposed for the rest of m6220.

  OFFSET groups: po1 (12, 17-20) to po1 (g1/1-g4/1); PO6 (a2, 17-20) to po6 (g1/2-g4/2)

  All is well. the Television ether on the Cisco displays LACP is in place and working well, like the fact the same command on the side of Dell.

  I did all the LAGS interfaces trunks and originally supposed to Dell was like Cisco while none allowed VLAN defined means all the VLANS allowed. I've since read that Dell default behavior is to only authorized WHAT VLAN specified. I've added the appropriate VLAN on the side of Dell.

  Pings between m6220 very well work. Pings to the rest of the network the m6220 very well working. Pings between the 6506 and the blades are not.

  The blades run ESXi 5.5U2 and I added two interfaces tissue management vSwitch. I first tried to make the m6220 g1/1 an access port, but that did not work. I tried making a port trunk and setting one VLAN, but this does not work either.

  What information is needed to help with this?

  Thank you.

  I'm done just erase everything and start over. Sometimes when you have changed all sorts of things, create a clean starting point, it is what is needed.

  Daniel, thanks for the reply and suggestions.

  Here's the configs that worked as I expect. I hope someone can benefit from my efforts.

  Cisco 6506:
  interface Port-channel1
description m1000e-ModuleA1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface Port-channel2
description m1000e-ModuleB1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface Port-channel3
description m1000e-ModuleC1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface Port-channel4
description m1000e-ModuleC2
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface Port-channel5
description m1000e-ModuleB2
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface Port-channel6
description m1000e-ModuleA2
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface GigabitEthernet1/1
description m1000e-ModuleA1-Port17
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
!
interface GigabitEthernet1/2
description m1000e-ModuleB1-Port17
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 2 mode active
!
interface GigabitEthernet1/3
description m1000e-ModuleC1-Port17
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 3 mode active
!
interface GigabitEthernet1/46
description m1000e-ModuleC2-Port17
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 4 mode active
!
interface GigabitEthernet1/47
description m1000e-ModuleB2-Port17
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 5 mode active
!
interface GigabitEthernet1/48
description m1000e-ModuleA2-Port17
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 6 mode active
!
interface GigabitEthernet2/1
description m1000e-ModuleA1-Port18
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
!
interface GigabitEthernet2/2
description m1000e-ModuleB1-Port18
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 2 mode active
!
interface GigabitEthernet2/3
description m1000e-ModuleC1-Port18
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 3 mode active
!
interface GigabitEthernet2/46
description m1000e-ModuleC2-Port18
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 4 mode active
!
interface GigabitEthernet2/47
description m1000e-ModuleB2-Port18
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 5 mode active
!
interface GigabitEthernet2/48
description m1000e-ModuleA2-Port18
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 6 mode active
!
interface GigabitEthernet3/1
description m1000e-ModuleA1-Port19
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
!
interface GigabitEthernet3/2
description m1000e-ModuleB1-Port19
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 2 mode active
!
interface GigabitEthernet3/3
description m1000e-ModuleC1-Port19
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 3 mode active
!
interface GigabitEthernet3/46
description m1000e-ModuleC2-Port19
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 4 mode active
!
interface GigabitEthernet3/47
description m1000e-ModuleB2-Port19
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 5 mode active
!
interface GigabitEthernet3/48
description m1000e-ModuleA2-Port19
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 6 mode active
!
interface GigabitEthernet4/1
description m1000e-ModuleA1-Port20
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
!
interface GigabitEthernet4/2
description m1000e-ModuleB1-Port20
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 2 mode active
!
interface GigabitEthernet4/3
description m1000e-ModuleC1-Port20
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 3 mode active
!
interface GigabitEthernet4/46
description m1000e-ModuleC2-Port20
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 4 mode active
!
interface GigabitEthernet4/47
description m1000e-ModuleB2-Port20
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 5 mode active
!
interface GigabitEthernet4/48
description m1000e-ModuleA2-Port20
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 6 mode active
!
interface Vlan100
description Primary VLAN
ip address 192.168.100.4 255.255.255.0

  -------------------------------------------------------------------------------

  Dell m6220-a1

  interface vlan 100 1
  ip address 192.168.100.41 255.255.255.0
  !
  interface Gi1/0/1
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/2
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/3
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/4
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/5
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/6
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/7
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/8
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/9
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/10
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/11
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/12
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/13
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/14
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/15
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/16
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged
  exit
  !
  interface Gi1/0/17
  channel-group 1 mode active
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  exit
  !
  interface Gi1/0/18
  channel-group 1 mode active
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  exit
  !
  interface Gi1/0/19
  channel-group 1 mode active
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  exit
  !
  interface Gi1/0/20
  channel-group 1 mode active
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  exit
  !
  interface port-channel 1
  description "Cisco 6506 Po1"
  switchport mode general
  switchport general acceptable-frame-type tagged-only
  switchport general allowed vlan add 100 tagged

  The remaining Dell m6220's are the same with the port-channel changed.


• Reference Dell MD3200i correct editing with IP system and the NIC for faster network speeds

  Hi all

  I worked on this project for a while now. I did a lot of research and have contacted Dell several times. I need help.

  I have 2 sets of identical to use for Hyper-V clusters servers. We bought a Dell MD3200i in November, we also bought a Dell 5424 switch and a Cisco SLM2048 switch. These servers have Real Tek 2 network cards for iSCSI Jumbo frames is 9 k

  The Dell MD3200i is two SAN controllers. Dell 5424 is the iSCSI optimized switch and Cisco is a 48 switch ports. iSCSI is on its own network that nothing else is connected to it. (There is an Iomega NAS and a promise Vtrak SAN Tech with all current domain of execution with iSCSI controller)

  Reference Dell MD3200i controller 0 Port 0 192.168.130.101 controller 1 Port 0 192.168.131.101

  Controller controller Port 1 0 192.168.130.102 1 1 192.168.131.102

  Controller controller Port 2 0 192.168.130.103 1 2 192.168.131.103

  Controller controller Port 3 0 192.168.130.103 1-3 192.168.131.104

  Cisco switch has 1 VLAN n ° 1 on it and the 130 subnet inside elements. There are 8 connections to the switch. 4 controller 0 and 1 of each of the servers. It has an IP of 192.168.132.4, but that switch IP does not make difference. Lighted Jumbo frames

  Dell switch has 2 of #1 for various things such as the domain controller, Vtrack, and SIN. Subnet 2 is 131 and has a total of 8 connectors inside. 4 in 1 controller and 1 from each of the servers. Lighted Jumbo frames. The switch IP address is 192.168.132.2

  Groups of servers. Each server node running Windows 2008 R2 SP1 and running hyper-v with virtual server clusters / storage folder on them. 2 Realtek NIC with Jumbo frames made 9 k ProdNode1 and ProdNode2 have 12 Core i7 CPU with 12 GB memory, EXNode1 and ExNode2 have 12 Core i7 CPU with 24 GB of memory.

  ProdNode1 iSCSI-1 192.168.130.110 ProdNode1 iSCSI-2 192.168.131.110

  ProdNode2 iSCSI-1 192.168.130.120 ProdNode2 iSCSI-2 192.168.131.120

  ExNode1 iSCSI-1 192.168.130.130 ExNode1 iSCSI-2 192.168.131.130

  ExNode2 iSCSI-1 192.168.130.140 ExNode2 iSCSI-2 192.168.131.140

  Portal discovery iSCSI on ProdNode1 went to 192.168.130.110 192.168.130.101 and 192.168.131.110 192.168.131.101 each of the other servers Discovery Portal have been pairs like this.

  iSCSI tab click on add 8 MPIO sessions at each of the ports on the MD3200i from Dell, target. For example, I added 1 session of 192.168.130.101 using it. Add Session,--> activate--> Advanced Mutlipath--> Local--> IP 192.168.130.110 initiator and target 192.168.131.101 iSCSI adapter. This is repeated on all servers. 4 connections for each NIC.

  The network is very slow. It revolved around 2 to 4 MB/MIN and it should be much faster. Initially, we had only the Cisco switch with only 1 VLAN and everything connected directly to it. I read somewhere that MPIO has been the problem, so I went through the same configuration but does not verify the MPIO checkbox above. Once this has been done, the network speed went up to 1.5 GB/Min but modular storage Dell was not happy, and virtual servers would fail and the connection is not very stable.

  What wrong with my setup? Can I directly home and fix the servers directly to the PowerVault and will make stable and allow for failover and redundancy NIC? I need to get this stable so I can move with something else.

  Thank you Ron

  You will need to change your system of intellectual property on this:

  rbramble

  EX-Node1 iSCSI-1 192.168.130.130

  EX-Node1 iSCSI-2 192.168.131.130

  EX-Node2 iSCSI-1 192.168.132.140

  EX-Node2 iSCSI-2 192.168.133.140

  Prod-Node1 iSCSI-1 192.168.130.10

  Prod-Node1 iSCSI-2 192.168.131.10

  Prod-Node2 iSCSI-1 192.168.132.20

  Prod-Node2 iSCSI-2 192.168.133.20

  Reference Dell MD3200i

  Controller 0 Port 0 - 192.168.130.101 Jumbo Frames 9K

  Controller 0 Port 1 - 192.168.131.101 Jumbo Frames 9K

  Controller 0 Port 2 - 192.168.132.101 Jumbo Frames 9K

  Controller 0 Port 3 - 192.168.133.101 Jumbo Frames 9K

  Controller 1 Port 0 - 192.168.130.102 Jumbo Frames 9K

  Controller Port 1 1 - 192.168.131.102 Jumbo Frames 9K

  Controller 1 Port 2 - 192.168.132.102 Jumbo Frames 9K

  Controller 1 Port 3 - 192.168.133.102 Jumbo Frames 9K

  Your iSCSI sessions will be:

  For EX-Node1:

  -192.168.130.130 to 192.168.130.101

  -192.168.130.130 to 192.168.130.102

  -192.168.131.130 to 192.168.131.101

  -192.168.131.130 to 192.168.131.102

  For EX-Node2:

  -192.168.132.140 to 192.168.132.101

  -192.168.132.140 to 192.168.132.102

  -192.168.133.140 to 192.168.133.101

  -192.168.133.140 to 192.168.133.102

  For Prod-Node1:

  -192.168.130.10 to 192.168.130.101

  -192.168.130.10 to 192.168.130.102

  -192.168.131.10 to 192.168.131.101

  -192.168.131.10 to 192.168.131.102

  For Prod-Node2:

  -192.168.132.20 to 192.168.132.101

  -192.168.132.20 to 192.168.132.102

  -192.168.133.20 to 192.168.133.101

  -192.168.133.20 to 192.168.133.102

• Reference Dell R210 II - update the Firmware on Centos 6

  Hello

  I have several dell servers connecting a mix of OS linux centos 5/6 for windows and xen etc.

  I have run it on every Linux machine to install the dell tools:

  wget - q - O - http://linux.dell.com/repo/hardware/latest/bootstrap.cgi | bash
  yum install srvadmin-all firmware-tools - y
  yum install $(bootstrap_firmware) y
  srvadmin - services.sh status
  / opt/dell/srvadmin/sbin CD.
  update_firmware - Yes

  on centos 5 is very well and on some centos 6 machines too. However, a new server got us set up this week, the following error occurs, I want to know how to solve this problem, so I can perform upgrades in the usual way via command line:

  Root@server[/opt/Dell/srvadmin/sbin]# update_firmware - Yes

  Inventory of the currently running system.

  Search the directory for storage of the available BIOS updates...
  Checking the BIOS - 2.2.3
  Available: dell_dup_componentid_00159 - 2.2.3
  Did not find a new installation package that meets all the checks of the facility.
  Verification of rev NetXtreme II Gigabit Ethernet 20 (em2) - 7.2.20 BCM5716
  Available: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8
  Found update: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8
  Check the system BIOS to PowerEdge R210 II - 2.2.3
  Did not find a new installation package that meets all the checks of the facility.
  Verification of rev NetXtreme II Gigabit Ethernet 20 (em1) - 7.2.20 BCM5716
  Available: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8
  Found update: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8

  Found the firmware that needs to be updated.

  Updates running...
  -Installation of pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_... Package installation failed: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd)
  -7.4.8.
  aborting update...

  The command to low-level error message was:

  Unable to parse xml output, bad for the package: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd)
  Root@server[/opt/Dell/srvadmin/sbin]#

  the specification of the server:

  Reference Dell R210 II

  Intel Quad Core 3.2 Ghz
  16 GB of Ram
  CentOS 6.4 x 64
  1 x 256 GB SSD

  ChrisDuk112,

  Could you do me a favor and see if that solves the problem for you.

  the remount mount - o, suid, exec/tmp

  Let me know how it goes.

• Reference Dell T310 - laboratory home

  Hi all

  I want to buy 2 of the Dell Poweredge T310 server for my laboratory at home to practice and prepare for my VCP certification. Here is the specification I chose and please let me know if this is compatible and I'm good to go set up my lab, I have to make changes to these specifications? I have not ordered any RAID controllers and do I really need?

  PowerEdge T310 chassis with up to 4 hard drives and Quad Pack LED Diagnostics
  Delivery charges for PowerEdge T310
  16 GB 1333 MHz UDIMM memory
  X 3430 Xeon processor, 2.4 GHz 8 MB Cache, Turbo
  PowerEdge T310 heatsink of heat
  No controller
  No operating system
  Gigabit network adapter double built-in
  Controller BMC
  Cable for optical drive SATA for PowerEdge T310
  Integrated SATA, 1-4 hard drives connected to the integrated SATA - no RAID controller

  250GB 7.2 k RPM Serial ATA 3Gbps 3, cable 5po hard drive

  250GB 7.2 k RPM Serial ATA 3Gbps 3, cable 5po hard drive
  Non-redondante 375W PSU

  Thanks in advance,

  I found the focus check tracking if help http://communities.vmware.com/message/1475041

  I am looking in HCL - check result.

  Research: Your search for "Systems" returned 2 results.
  Display:

  Name of the partner	Model	CPU series	Supported releases
  REFERENCE DELL	PowerEdge T310	Intel i3/i5 Clarkdale series	ESX 4.1 U1 4.1 4.1 U1 4.1 ...
  REFERENCE DELL	PowerEdge T310	Intel Xeon 34xx series Lynnfield	ESX 4.1 U1 4.1 4.1 U1

  ? deviceCategory = Server & productid = 10062 & releaseid = 142 & deviceCategory Server = & partner = 23 & keyword = t310 & page = 1 & display_interval = 10 & sortColumn = partner & sortOrder = Asc "> 4.1 ...

  Please, do not forget the points of call of the "useful" or "correct" answers

  Mauro Bonder - moderator

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.

• Reference Dell 3110cn of Laserjet + os El Capitan

  My MacBook Pro (2009) stopped my Dell printer. News on this please.

  Hi deaconjo,

  as I had the same problem, I found a solution for my El Capitan MacPro 2008:

  Search for the following installation program:

  3130cn_Installer_And_Application_Dell_A04_MAC.dmg

  Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:

  Reference Dell 3130cn Color Laser v3017.104 PS

  With this driver installed, I can use my printer Dell 3110cn without problem.

  Perhaps it might help you too.

  Concerning

• Reference Dell Sonicwall SRA

  Hey guys, more of a statement than a question. If you have a Dell Sonicwall and users do "found no appropriate group" of course the same user does not exist as a local user and a domain user. This will cause problems. Took me a while to understand that >.<>

  Good thought.

  Thank you
  Ben D
  Reference Dell SonicWall
  #Iwork4dell