Installation of Windows Server 2008 R2 on Poweredge R820, where the hell are the drivers preinstall?

Similar Questions

• Installation of windows server 2008 R2 on Poweredge R320

  Hello everyone

  We bought a new Poweredge R320 server in order to install 64-bit Windows Server R2. There are 2 drives inside and they are preconfgured as raid1.

  I changed the configuration of SATA in RAID mode and also initialized by PERC-H310 RAID1 without any problem. When the server starts up, I see the following messages.

  We found no Raid 0 disks

  1 Vitrual disk (s) were found.

  
  I can boot from the windows media but no disks are found and is prompting me to browse and install the drivers from nesseray. So I downloaded

  SAS Raid drivers from this link: ftp://ftp.dell.com/Pages/Drivers/poweredge-r320.html#Drivers%20for%20OS%20Deployment

  Windows 2008 R2 64 Bit driver for controllers in PERC H310/H710/H710P/H810 Windows 2008 R2 64 Bit driver for controllers in PERC H310/H710/H710P/H810

  Recommended

  5.2.220.64

  18/10/2012

  Windows Windows Server 2008 R2

  The name of the file is: DRVR_WIN_M20VR_5.2.220.64_A02_ZPE.exe

  I extracted the contents of a USB, restarted the server and when you are prompted for drivers during the windows installation, I traveled to USB which 2 files are found.

  nodev.inf

  percsas.inf

  I tried both of them, but every time I get a message saying to make sure that the correct drivers are found. It seems that is not the correct drivers.
  

  Could be he you please direct me to the correct drivers? Or if you have any suggestions please let me know.

  Thank you very much

  Goudeuk

  PS: I posted the same topic in the forum "Blade" by mistake. Apology.

  "Do you mean that if my BIOS/SATA configuration has been set to RAID 1 I should have drivers chipset/AHCI for a successful installation?"

  No, because you are not using the onboard SATA RAID - your built-in SATA is used ONLY by your optical drive, so it should not be in RAID and AHCI usually requires special drivers, which is not required when you use optical drives.  However, pilots of chipset/AHCI may have helped Windows to see the optical drive in such a way that the installation could proceed (if she needs the RAID controller for real hard disks, you will NOT see this particular message - you will see another message when Windows cannot find not all drives to be installed on).

  "When someone would set RAID 1 for sata configuration?"

  ONLY if you use the S110 RAID controller onboard.  You use the H310, so you don't want to mess with the SATA RAID on board.

• Installation of Windows Server 2008 R2

  Installation of Windows Server 2008 R2 on a server without an operating system present.  Get an error 0 x 80070017.  What is the cause?  It is a new server.

  Hello

  You can find the Server forums on TechNet support, please create a new post at the following link:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• FRM-92101: there was a failure when starting Server Forms... (R12 charge installation on windows server 2008 32-bit)

  Hello

  I encountered the following error when I try to open the form in oracle EBS R12.1.1

  It stuck for a little while and then appears an error message

  FRM-92101: there was a failure when starting Server Forms...

  (I've never been able to run the form on this)

  I ran a vision online forum that works very well which means java is ok.

  It is the new installation on windows server 2008 32-bit with costs of database (no vision).

  I search on the internet and tested all of the available options, including;

  change in the registry for example 1024,12288,1024 etc.

  marking the check box for oracle process manager to PROD "allow service to interact with desktop".

  check the configuration files of forms (all files of any bad path that I found and corrected)

  running files adautocfg.cmd for db and apps (returned errors and can be verified at the following link)

  https://DL.dropboxusercontent.com/u/60474194/adconfig%20apps.log

  https://DL.dropboxusercontent.com/u/60474194/adconfig%20dB.log

  I'm not a technical professional and unable to solve the problem, please help

  Problem solved

• I am trying to install Windows Server 2008. When I get to the part where I should choose where the operating system is to be installed, it is blank.

  I am trying to install Windows Server 2008. When I get to the part where I should choose where the operating system is to be installed, it is blank. He told me 'No device found drivers. We see the SATA HDD in BIOS, and if I browse for the drivers, the driver is displayed. I used the command line packaged with the installer to format the drive, just to be sure. It is formatted in NTFS.

  original title: can not select the HARD drive to install on

  Thank you for visiting the Microsoft Answers site. The question you have posted is related to Windows Server 2008 and would be better suited to the Windows Server TechCenter community. Please visit the link below to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads

• Windows Server 2008 R2 gets really slow, loses the connection, network printers.

  I have a Windows Server 2008 R2, Dell PowerEdge T610 which very often at a time, it is really slow, loses the connection to all network printers and network resources are limited. We check scheduled task, updates of Windows and go on throughout this period. We check the event viewer, and there is nothing extraordinary. Does anyone have any ideas or suggestions?

  Hello

  Sorry for the inconvenience that you are experiencing.

  Since we are unable to help you better on the problems associated with Windows Server 2008 R2. Our TechNet team have the expertise to help guide you accordingly.

  That's why I ask you to please get in touch with our TechNet support team to resolve the issue.

  I appreciate your cooperation in this regard.

  Hope this will answer your query.

• Windows Server 2008 crash - need help to analyze the minidumps

  We have a Windows Server 2008 which crashed 5 times in the last days.

  I placed the file 120313-41636 - 01.zip that contains all 5 landfills in my public skydrive folder to- https://skydrive.live.com/?cid=446280106bb642de#cid=446280106BB642DE&id=446280106BB642DE%21140

  Any help would be appreciated

  Hello

  Please post your question in Server TechNet Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• shared files Windows server 2008 when I try to access the logged error shows try 704 form again later.

  shared files Windows server 2008 when I try to access the logged error shows try 704 form again later. While it uses this file from the last three months

  Hi Maury,

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows Server on TechNet forum. Please post your question in the TechNet Windows Server 2008 R2 Networking - read only forum.

• I have Windows Server 2008 R2. I have set up the desktop remotely for 5 users, but each time a user logged on to the other user will be disconnected.

  issue license remote dekstop

  I have Windows Server 2008 R2. I have set up the desktop remotely for 5 users, but each time a user logged on to the other user will be disconnected. Is this a problem with the license? Is it how do I get license for 10 users remote desktop? Thank you

  You will get the best answers by posting in the dedicated remote desktop on TechNet Forum:

  Remote Desktop Forum services (Terminal Services)

• I have VSS enabled on my server sp2 Windows server 2003 and out of no where the tab versions previous disappeared...

  I have VSS enabled on my server sp2 Windows server 2003 and out of no where the tab versions previous disappeared for all users when you access from anywhere.  I deactivated and reactivated the snapshots and it won't come back please advise...

  Hello ErekBye,

  Thank you for visiting the website of Microsoft Windows Vista Community. The question you have posted is related to Windows Server 2003 and would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads

  Best regards

  Matthew_Ha

• Installation of Windows server 2008 on Poweredge R320

  Hello everyone

  We bought a new Poweredge R320 server in order to install 64-bit Windows Server R2. There are 2 drives inside and they are preconfgured as raid1.

  I changed the configuration of SATA in RAID mode and also initialized by PERC-H310 RAID1 without any problem. When the server starts up, I see the following messages.

  We found no Raid 0 disks

  1 Vitrual disk (s) were found.

  
  I can boot from the windows media but no disks are found and is prompting me to browse and install the drivers from nesseray. So I downloaded

  SAS Raid drivers from this link: ftp://ftp.dell.com/Pages/Drivers/poweredge-r320.html#Drivers%20for%20OS%20Deployment

  Windows 2008 R2 64 Bit driver for controllers in PERC H310/H710/H710P/H810 Windows 2008 R2 64 Bit driver for controllers in PERC H310/H710/H710P/H810

  Recommended

  5.2.220.64

  18/10/2012

  Windows Windows Server 2008 R2

  The name of the file is: DRVR_WIN_M20VR_5.2.220.64_A02_ZPE.exe

  I extracted the contents of a USB, restarted the server and when you are prompted for drivers during the windows installation, I traveled to USB which 2 files are found.

  nodev.inf

  percsas.inf

  I tried both of them, but every time I get a message saying to make sure that the correct drivers are found. It seems that is not the correct drivers.
  

  Could be he you please direct me to the correct drivers? Or if you have any suggestions please let me know.

  Thank you very much

  Goudeuk

  Even I have the same problem... Can anyone suggest a solution?

  Thank you

  Scott

  http://www.vmexplore.com

• Failed Installation of Windows Server 2008.

  Hey,.

  I recently tried to install Windows Server 2008 on ESXi 4.0.0 (revision 1).

  The installation went all the way until they have to 'Finish installation', how come wrong stop installation.

  "Setup.exe - bad image".

  

  After that, another windows came up saying that windows could not be configured for use on the hardware in my server.

  Could someone advise me to solve this?

  Thank you.

  Oliver.

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• SITE v2.0 failed Installation on Windows server 2008 R2 with SP1

  Installing CPID v2.0 on Windows server 2008 R2 with SP1, the Setup log reported that the installation failed with the error "CustomAction RollBackSccmComponents returned error code 1603"

  I run the Setup with this command after you open the command prompt as 'Run as administrator ':

  MsiExec.exe /i Dell_Client_Integration_Pack.msi

  I even put the command above into a batch file and run it with the same result. With the help of Trace32, I also found this error to be the main problem causing the failure of this facility:

  "custom action InstallSccmComponents unexpectedly closed the hInstall (type MSIHANDLE) handle provided. The custom action must be set to not close this handle.

  Autour Googling, I came across this link: http://en.community.dell.com/techcenter/enterprise-client/f/4448/t/19416814.aspx to try to perform the steps below, but when I did the steps below, the installation just rolled back without even beginning the installation:

  Steps in the link above:

  *********************************************************************************************************

  "We have found this to be a problem with the way that the custom action is running in the MSI file, it is executed in the context of the user who was unable, we changed this to run in the context of the system that solved the problem. To do is relatively simple;

  First unzip the files from the downloaded executable deployment package. Then, download Orca here, http://blogs.msdn.com/astebner/archive/2004/07/12/180792.aspx. Once installed Orca, do a right click Extract MSI and select, "Edit with Orca. Once Orca lance, do not panic, just click on the top menu and select, "Transform", then select "Transformation." Then go to the 'Custom Actions' Table on the left and find the "InstallSccmComponents" entry on the right; Change the value in the column "Type" 3073, then go to "transform", "Generate Transform", save the transformation in the same directory as your MSI and select, and then close Orca.

  To install, use the following command line;

  MsiExec.exe /i \Dell_Server_Deployment_Pack_v1.2_for_ConfigMgr_A01.msi TRANSFORMS =-number

  = The path to the directory containing the package deployment installation files and your STDS. »

  *****************************************************************************************************

  Has anyone seen this problem before? And if so, how to solve?

  Thank you

  TeeDarling77

  I found myself by opening a ticket with Dell to get this problem finally solved. After the installation of Dell's Support log shipping, they asked me to follow these steps below:

  1 if the SQL DB is on a separate machine, try to create the "SMS_TaskSequence_Action" class in WMI under \\.\root\sms\site_ >.  You can download WMI Explorer to browse if you want to see if this class already exists.  Run the script below will not hurt if it already exists.

  a. here are the instructions to create the custom class.  First open powershell as an administrator.

  b. set-executionpolicy RemoteSigned

  c. change the extension on the attached in .ps1 file and change the file to replace the "site_abc" by "site_their 3 letter site code.

  d. change the storage location of the ps1 file.

  e... \WMIClassAdd.ps1

  f. restart and try the installation again.

  3. If it still does not work, send me the newspaper install again to look at.

  Note:

  Here is what was in the attachment in step C.

  ****************************************************************************

  $newClass = ' new-Object System.Management.ManagementClass

  ("root\sms\site_abc", [String]: empty, $null);

  $newClass ["__CLASS"] = "SMS_TaskSequence_Action";

  $newClass.Qualifiers.Add ("Static", $true)

  $newClass.Put)

  *************************************************************************

  After you run the instructions above and restarted the server, installing v2.0 CPID ended successfully.

  I hope that these instructions will help someone in the future... :))

  TeeDarling77

• OM_5.4.0_Man_Node_A01.msp installation fails (Windows Server 2008 x 64)

  I can't get it to load the patch installer. Of course, life would be easier if Dell has released a proper version of OpenManage (with support for Windows Server 2008 x 64).

  Here are the instructions...

  Application of the Service Pack
  1 double-click the MSP file or enter the following in a command prompt window:
  MsiExec.exe /p OM_5.4.0_Man_Node_A01.msp

  And the error message...

  Windows install

  The upgrade patch cannot be installed by the Windows Installer because the program to be upgraded is may be missing, or the upgrade patch may be a different version of the program. Verify that the program to be upgraded exists on your computer and that you have the correct upgrade patch.

  
  

• Assistance needed for the installation of windows server 2008 r2

  Hello users,.

  I am new to this technology of the virtual environment and I need help in installing windows server 2008 r2 on a machine virtual workstation. For it so what are the recommended setting for drivers, no. of processors, amount of RAM, type of CISS or sata... etc to give the best performance on my virtual machine. If possible please provide me details to my knowledge.

  Thanks in advance

  Are you sure that you have installed a Windows Server 2008 R2?

  Because the normal procedure is that after the installation, you will get a prompt to choose an administrator password. Once you are connected.

  There is no additional user created during installation. This only happens when you install versions of Windows desktop.