Installation/running with no colour ethernet port?

Similar Questions

• The bridge network to the ethernet ports

  I have an Airport Extreme base station for my wireless at home. The problem I have is that the base station is not near a few features, that I need to hard wire. I read that you can set up a network bridge and if I understand correctly, this concept, it's like setting up of another wireless device, but this second device provides you with the required Ethernet ports for connectivity. Is it possible to do with the Airport Express secondary device?

  Most of the other posts that I read said to extend the wireless range, but the range of my base station is not the issue. I just need a couple on the way ports. I've heard this can slow down the entire network however. Is this feasible? All known reserves? Advice is appreciated.

  Is it possible to do with the Airport Express secondary device?

  Yes

  Most of the other posts that I read said to extend the wireless range, but the range of my base station is not the issue. I just need a couple on the way ports. I've heard this can slow down the entire network but

  It all depends on if you configure the AirPort Express to "extend" the network... which will lower the maximum speed potential of the network by all 40-50%...or...whether that you set up the base AirPort Express for simply to 'join' the network... which causes a decrease in the speed of the network... but it will provide 2-port Ethernet for wired devices.

  If you need more than 2 ports Ethernet on the Express, you can add an Ethernet 5 port, 8-port switch, etc., to create as many ports as you need.

  Don't know what kind of speed you need for the Ethernet ports, but they are limited to 100 Mbps, then that would be the maximum speed available ports Ethernet on the Express.

• How can I transfer the mail, Safari, iTunes, etc of my 2008 MacBook running OS 10.5.8, a new MacBook Pro (with Ethernet port) or a new MacBook Air?

  I replace my 2008 Macbook which maxed out at OS 10.5.8, with a new MacBook Pro or MacBook Air.  The Pro has an Ethernet port, the Air is not.  I want to transfer all the data from my application (mail, Safari, iTunes, etc.) for the new Macbook that will run El Capitan.  How can I do?

  What machine you're leaning towards? With Air, you have to use ether WIFI or have the old drive on an external drive configuration. With a new Macbook Pro, the simplest method is to use the migration assistant. Access your Macbook in public services and to see, there you have it. Here is a link to what you can do.  http://pondini.org/OSX/SetupLion.html It is said Lion, but it applies the same. Here's what apple says.  https://support.Apple.com/en-us/HT204350 you should know that some of the apps in Leopard will be obsolete in El Captian. There you transfer, it can cause problems. I use the thinking that if I can replace it with a download I do this. The transfer or, if there is an update for it.

• How is it that a computer which works very well with a direct Ethernet connection won't work with a switch, however any other computer using the same port, cable, ect, and so on, can?

  Switch issues. Help, please.

  How is it that a computer which works very well with a direct Ethernet connection won't work with a switch, however any other computer using the same port, cable, ect, and so on, can? We already checked the firewall as a question, that it was not, and now, we are puzzled.

  Well, I know that the issue is long-term... believe me, it's a long, but as they say, the devil is in the details. Anywho, the question is, my grandfather has a HP laptop, which for two years has been able to run through a Linksys switch to his router and connect its printers to his laptop. About two months ago it suddenly doesn't work like that. Now, it works fine if it plugs directly into the router/Ethernet. My uncle suggested that the switch was bad, but after testing the same port, cable and all, the switch worked well for him. ' GRAMPS really needs this answered, but someone else, it is called can not understand and now I, in turn, ask you all for what you can offer. Here are the ideas that we have already discredited.

  -Switch bad: as above, is that this particular laptop, even under identical conditions, the works of my uncle very well.
  -Bad NIC: debunked through the fact we connected to the computer directly to the router and it worked fine.
  -Bad configuration of the firewall: we have disabled the firewall (please do not notice, he wasn't the smartest idea, we already know) and even if she recorded the switch exists, the internet is always triggered when you are connected with the switch.

  Thanks in advance for any assistance that you can provide and Merry Christmas to you all.

  It would be useful to consult the results of the ipconfig/all command both when it is connected to the switch and when it is connected directly to the router.  In addition, what is the model of the switch?

  To save the manual copy and the new hits of the ipconfig/all command output-

  First connect through switch.
  Open a command prompt window (start > run > cmd > OK)
  Type the following lines in the black command prompt window and press ENTER after each line

  echo "Connected via the button" > "% UserProfile%\Desktop\ipinfo.txt".
  ipconfig/all > "% UserProfile%\Desktop\ipinfo.txt".

  Now connect directly to the router, type the following lines in the command prompt window and press ENTER after each line

  echo "Connected to the router" > "% UserProfile%\Desktop\ipinfo.txt".
  ipconfig/all > "% UserProfile%\Desktop\ipinfo.txt".
  Notepad '% UserProfile%\Desktop\ipinfo.txt '.
  output

  Copy the contents of the Notepad window in your response (if you use the laptop when it is connected directly to the router) or close the Notepad window, and then copy ipinfo.txt of the laptop to the Gramps in a USB FlashDrive you can connect to any computer allows you to answer.

  You can delete ipinfo.txt on the desktop when you are finished.

• Nexus 7009 does not show the N7K-F248XP-25 modules ethernet ports n sh run

  Hello world

  I have a question...

  I'm going to install two Nexus 7009 with N7K-F248XP-25 three modules on each of them, I plan to create 3 VDC, but initial configuration, the system does not display the Ethernet ports of these modules, even with the inventory of show and show module that I can see that the modules are recognized and its status is OK. Is there something I need to do before you start to configure these modules...? allow some feature or the license in order to see the ports with show running CLI...?

  You can activate the F1, F2, M1, M1XL, and M2XL series modules. There is no restriction on the type of mixture allowed for the order of module-type system. Control module-type system allows a mixture of F1, F2, M1, M1XL and M2XL series of modules in the VDC.

  Note The module-type limit-resource command handles the restrictions on the types of module that can be mixed in the VDC.

  Note Use the f2 type module-system command to allow the F2E series modules in a VDC. The ports of F2 and F2E series modules can be distributed as all other ports.

  Note The modules that you do not select must not be powered on after you configure this feature and enter Yes. An error message will force you to manually disable these modules before you continue. You will avoid significant disruptions and problems of service within a VDC.

  No form of this command resets the configuration mode to enable all modules.

  hope this helps

• My Ethernet port is not running iMac mid 2011. Pls help me.

  Hi, I have an iMac 21.5 "mid-2011. My Ethernet port is not working. Is this a software problem? Pls help me.

  Try resetting the SMC reset management system (SCM) controller on your Mac - Apple Support

  Try another ethernet cable.

  He still does not? A report with the information more wrote an effective communities of Apple Support question

• Tecra S5 - slow ethernet with USB 2.0 Port Replicator

  Hello

  I have a Tecra S5 with USB 2.0 Port replicator II. I have 3 ethernet connections all together on my PC: LAN on motherboard, WiFi and the other on the USB port replicator.

  At home, I use WiFi for internet connection and USB to Ethernet to a wired connection to devices with built-in web server.

  My problem is that when the WiFi and USB to Etherenet is active the internet and the connection to the web server works but vey slow.
  If I turn off the WiFi and connect to the web server works properly.
  If I disable USB for Ethernet internet connection works correctly.

  Anyone has same problem and suggestion how to solve?
  I downloaded the latest drivers from the Toshiba support page.
  My OS is XPSP2.

  Concerning
  jballa

  Hello!

  It looks like a network configuration problem. Check the network addresses and configuration in command line with the command ipconfig/all.

  Try using static IP addresses. I think that the DHCP server takes a long time to go send an IP address to each laptop.

  Good bye

• RN102 fuel, ethernet port with a light

  Hello

  I have a problem with one of our readynas it will not feed.

  When I plug the power in no fan activity and no lights on the front, but the ethernet port has a light.

  I tried the adapter in a voltmeter and everything is ok.

  Any other suggestions?

  NETGEAR talked and got a replacememnt warranty unit was dead, put hard drives in all and save work without data loss.

• Modbus IO with several ethernet ports?

  Dear experts LabView:

  My Labview system must communicate with three slaves Modbus (variable speed drives of motor with Modbus TCP/IP option installed) to send orders (speed set), and status of the drive reading (the actual speed, output current/voltage/power etc.). The PC has an Ethernet card to four ports with three of the ports connected via a standard Ethernet cable to the three controllers. Three ports on the PC Ethernet received (192.168.1.10, 192.168.1.11, 192.168.1.12) static IP addresses. The three controllers have been configured to give the Modbus slave static IP address options as well (192.168.1.20, 192.168.1.21, and 192.168.1.22). I also downloaded the NI Modbus (version 1.2) library and want to use its screws to perform query operations master Modbus. To do this, he must first open TCP connections on three slaves using the connection open TCP vi, and that's where my problem comes in. How TCP connection open connection to use a specific port to Ethernet (one of the first three IP addresses) on the PC? Thanks in advance for your help.

  VRA

  Hi VRA,.

  What you mean? There is a port entry.

  Mike

• OfficeJet 6500 a printer seems to have disabled - ethernet port is blocked with the yellow plug.

  Hi, I bought an OfficeJet 6500 has more around a year ago and have been using it with variable success using wireless internet. I thought that it might help to connect using wired ethernet, but I just discovered that the ethernet port is blocked by a yellow card.

  Documentation that I found online, this expected to be activated, so I do not understand why it is not - can someone explain what is happening?

  It's a shipping plug, just remove the CAP and you will be able to set the ethernet cable.

• How can I configure two ethernet ports to connect to a VPN with Windows Server 2008?

  Something I can put in place, but im stuck with an error that I get is that I need two ethernet ports to configure vpn but why and how do I make it work I like

  original title: vpn windows Server2008

  In order to configure the VPN, you can take a look at:

  http://TechNet.Microsoft.com/en-us/library/cc725734 (WS.10) .aspx

• whean I run any program related to windows, finally installation failed with error code: (0x80070005)?

  I tried to run the .NET framework. All files are downloaded, but finally the installation failed with error code: (0x80070005)

  NET FRAMEWORK 4 fails installation

  1) download setup of .net 4 by http://www.microsoft.com/download/en/details.aspx?id=17718

  2) double-click the downloaded file to start the installation

• vCAC6 IaaS installation fails with configuration wizard - cannot run SQL Create User command

  Kia Ora.

  Put together the first poc vCAC6. The devices are in place and works fine, now up to IaaS Win2k8r2 with local SQL Express and this install fails. Pre-Reqs work. Installed and patched .NET 4.5 (not 4.5.1) as well.

  I installed as a local administrator on the server arrived at the field of IaaS. Installation running. EXE using run as administrator.

  The installation creates the database in SQL Express premises. I slowly raised privileges to solve the problems, but the same lines are written to the LOG file and there is an installation failed.

  News: 2014-01-15 09 49 58 588 h: construction project is "C:\Program Files (x86)\VMware\vCAC\Server\Database\DeployVMPS.xml" (BuildDB Target.

  News: 2014-01-15 09 49 58 604 h: build succeeded.

  News: 2014-01-15 09 49 58 604 hours: 0 warning (s)

  News: 2014-01-15 09 49 58 604 h: error (s) 0

  News: 2014-01-15 09 49 58 620 hours: time 00:03:35.12

  News: 2014-01-15 09 49 58 667 hours: CREATE USER [serverName\Administrator] to [NVCACIAAS\Administrator] CONNECT

  News: 2014-01-15 09 49 58 682 hours: EXEC sp_addrolemember 'db_owner', 'serverName\Administrator. "

  Error: 2014-01-15 09 49 58 854 h: error: vCAC Configuration Wizard is unable to run the Sql CREATE USER [serverName\admin] FOR LOGIN [serverName\Administrator] command.

  Error: 2014-01-15 09 49 58 854 h: error: vCAC Configuration Wizard is unable to run the Sql CREATE USER [serverName\Administrator] FOR LOGIN [serverName\Administrator] command.

  Is not not a SQL guru, I tried to elevation of privileges and exchanged between using SQL and Microsoft connection. tried to hook up with a new SQL and AD security with rights to MSDB db_owner account. Also as a 'Microsoft authenticated. " each re - run provides the same statements without worrying if the localMachine\Administrator account exists or not.

  Any help much appreciated.

  Thank you and happy new 2014!

  Hi there.

  I added the administrator account of the local computer in the security of SQL Express to the sysadmin role and installation is complete. ?!? Although I tried to use the SA account to install and the same messages of error and success in this file as well newspapers runs.

  Now these lines look like this;

  News: 2014-01-15 10 21 50 978 hours: Service NVCACIAAS\Administrator account is the same account that creates the database.  Task of grant of role of ignored by the database owner.

  News: 2014-01-15 10 21 50 994 hours: Service NVCACIAAS\Administrator account is the same account that creates the database.  Task of grant of role of ignored by the database owner.

  If it is installed, but I don't know why I need to raise the local Sysadmin role administrator account so he could complete or why to create the user account wrong localMachine\Administrator in installation because there was.

  I've rolled back to a previous snapshot and was able to repeat the failure until I added this user account to the Sysadmin role.

  Her go configuration and usage vCAC now. I'll repeat the installation at a later stage.

  see you soon

• Using the second ethernet port to connect to the printer?

  Hi I have a Mac Pro 2.1 old school and I'm wondering if I can connect to the network with an ethernet port and connect the latter to a printer?

  If so, how?

  Yosemite running.

  Thank you

  Physically, you use a port and a cable to connect to your network and use the second port and a second cable to connect directly to the printer. The printer must obviously have an interface Ethernet himself.

  However, you need to configure the second port on the Mac and the Ethernet port on the printer for each manually configured the TCP/IP addresses and these should be in a range of different network to your main network.

  If you the main network is something like 192.168.1.1 then your printer and the port on the Mac connection to this need to be in another network, such as 192.168.11.1.

  In theory, if the printer supports Hello aka. mDNS, then maybe you can get away with not having to configure TCP/IP addresses for the connection.

  The main reasons to use a second separate connection as this would be the performance or security, and frankly I don't think that's really relevant here. This would mean that no other computers on your network will be able to access the printer.

• Dynadock U3.0 - cannot use the Ethernet port after update 8.1 Win

  Hello world

  I use a u3.0 dock Dynadock with my Vaio PCS 13.
  I'm not able to use the Ethernet port on the Dynadock since I updated my Windows 8.1 device update 1.
  Before that everything worked well.

  I'm not able to re-install the drivers correctly (tried 7.6m0, 7.5m2). While the game driver tries to start, I get an error message, Setup is not able to put a bunch of registry (SYSTEM\CurrentControlSet\Services\DisplayLinkGA\D evice1) keys (up to 0). (Image 1)

  If I ignore these messages and do not install the driver, the Ethernet port will not installed in Device Manager. (Image 2)

  If I try to install the driver manually (DisplayLink network adapter NCM), I'll get an error message that a driver has been found but that access has been denied. (Image 3)
  I started the safe mode and could install the driver. But if I reboot in normal mode, the machine could not be started.

  I also tried to disable UAC and I am logged on as administrator 'real '.

  Please find the attached messaged (in German) error:

  [picture 1]: http://picload.org/image/lcalwop/toshiba.png
  [Picture 2]: http://picload.org/image/lcalwoc/toshiba2.png
  [Picture 3]: http://picload.org/image/lcalwlg/toshiba3.png

  BTW: If I unzip the Installer (7.6m0) and install * inf for the good Fri & dev (4503) it still does not work...

  I put t know what to do anymore...

  Hello

  After upgrade to 8.1 Windows, you should also update the software/driver Display Link
  This is very important!

  The latest version of the driver can be downloaded here:
  http://www.DisplayLink.com/support/downloads.php

  Note: the old version must be removed!