Intel PCI-E 10 Gigabit not recognized

Similar Questions

• Intel PCI X 520 10 WHAT GIGABIT SFP + not loaded in ESXI 6.0

  Hi all

  I'm under ESXI 6.0 and installed the latest drivers from intel PCI X 520 10 Giga cards with branch above DELL SFP modules I searched the forum for similar issues and found that it was perhaps the module are not supported so here my info of the commands below

  I have also the same out put regarding this thread cards PCI of Intel x 520 (82599EB) and the correct SFP + modules

  less /var/log/vmkernel.log | grep-i "FPS".

  (2015 09-29 T 08: 53:22.296Z cpu2:33341) < 3 > IGB 0000:0: 00.0: failed to load because a type of module SFP + and QSFP not supported has been detected.

  (2015 09-29 T 08: 53:22.316Z cpu2:33341) < 3 > IGB 0000: 0a: 00.1: failed to load because a type of module SFP + and QSFP not supported has been detected.

  also this command

  lspci | grep vmnic *.

  0000:03:00.0 network controller: Broadcom Corporation NetXtreme BCM5719 [vmnic0] Gigabit Ethernet

  0000:03:00.1 network controller: Broadcom Corporation NetXtreme BCM5719 [vmnic1] Gigabit Ethernet

  0000:03:00.2 network controller: Broadcom Corporation NetXtreme BCM5719 [vmnic2] Gigabit Ethernet

  0000:03:00.3 network controller: Broadcom Corporation NetXtreme BCM5719 [vmnic3] Gigabit Ethernet

  0000:07:00.0 network controller: Broadcom Corporation NetXtreme BCM5720 [vmnic4] Gigabit Ethernet

  0000:07:00.1 network controller: Broadcom Corporation NetXtreme BCM5720 [vmnic5] Gigabit Ethernet

  0000: 0a: 00.0 Network controller: Intel Corporation 82599 10 Gigabit double Port card WIRELESS [vmnic6]

  0000: 0a: 00.1 Network controller: Intel Corporation 82599 10 Gigabit double Port card WIRELESS [vmnic7]

  the problem is the vmnic6 and 7 is not displayed on the list vmnic

  ethtool-i vmnic6

  Cannot control himself fd: no such file or directory

  I also checked this thread How can I activate my to use 10GbE ports (need to create new VMKernel) are not in the list of adapters.

  VMware-l

  VMware ESXi 6.0.0 GA

  list of network adapter for the network esxcli

  Name PCI Device Driver status Admin link status speed Duplex MAC address MTU Description

  ------  ------------  ------  ------------  -----------  -----  ------  -----------------  ----  -------------------------------------------------------

  vmnic0 0000:03:00.0 tg3 Up Up 1000 Full 40:a8:f0:29:6 has: 20 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719

  vmnic1 0000:03:00.1 tg3 Up Up 1000 Full 40:a8:f0:29:6 has: 21 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719

  vmnic2 0000:03:00.2 tg3 Up Up 1000 Full 40:a8:f0:29:6 has: 22 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719

  vmnic3 0000:03:00.3 tg3 Up Up 1000 Full 40:a8:f0:29:6 has: 23 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719

  vmnic4 0000:07:00.0 tg3 Up Down 0 40:a8:f0:36:15:0e half 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5720

  vmnic5 0000:07:00.1 tg3 Up Down 0 40:a8:f0:36:15:0f half 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5720

  also check the bios for a similar option

  BIOS "Default memory mapped IO above 4 GB option in the BIOS.".

  I have not found this option, I HP Proliant DL380 Gen8.

  esxcfg-NICS - l

  Name PCI Driver link speed Duplex MAC address MTU Description

  vmnic0 0000:03:00.0 tg3 up to 1000Mbps Full 40:a8:f0:29:6 has: 20 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719

  vmnic1 0000:03:00.1 tg3 up to 1000Mbps Full 40:a8:f0:29:6 has: 21 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719

  vmnic2 0000:03:00.2 tg3 up to 1000Mbps Full 40:a8:f0:29:6 has: 22 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719

  vmnic3 0000:03:00.3 tg3 up to 1000Mbps Full 40:a8:f0:29:6 has: 23 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719

  vmnic4 0000:07:00.0 tg3 0Mbps Down a half 40:a8:f0:36:15:0e 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5720

  vmnic5 0000:07:00.1 tg3 0Mbps Down a half 40:a8:f0:36:15:0f 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5720

  output-l esxcfg-module
  See attached file

  
  

  and one thing is in the bios I have unknown pci

  
  

  See attached file

  
  

  

  
  

  
  

  the question is do I have to replace the sfp only or the entire map that I bought recently or is there a fix for it in the latest version of ESXI?

  Thank you

  I can confirm compatibility.

  also a comment is to use the intel SFP modules with Pci cards intel. who works on esxi servers

• ET2 Intel not recognized

  HY,

  the Intel ET2 Quad Nic is not recognize new vsphere 41u1 (new installation). The map is on the HCL with 8086:1526, but in the simple.map there is no list. The pci.ids and "vmkvsitools lspci" is OK.

  Any ideas?

  Nico

  Have you tried with the CD of driver for chipset 82576 you can find on:

  http://www.VMware.com/download/vsphere/drivers_tools.html

  VMware ESX/ESXi 4.x driver for Intel 82576, 82580 and I350 Gigabit Ethernet Controller CD

  Version

  3.0.18

  Release

  28/04/2011

• Problem: Memory PCI Flash not recognized on Satellite M30X

  Hello

  Windows XP does not recognize my multicard reader. That he has still put memory PCI Flash not recognized (2 locations)

  I tried - uninstall the driver (and the camera) and reboot: does not work
  -install the cardbus driver: does not work either

  Have any hint?

  Mouk

  PS: Sorry for my bad English, I'm French ;)

  Hello

  Are you sure that the card is compatible with your laptop?
  As far as I know the card on the left site reader who, only available on some models, allows you to insert and read data from the SD card, smart media (SMM) MemoryStick pro, Multimedia card and XD picture cards.

  The PC card slot supports cards PCMCIA Type II

• Device Intel WLan 6230 USB not recognized in Satellite L655 running Win8

  I installed the Intel Centrino card 6230 WLAN for laptop Toshiba Satellite L655 of my wife (introduced to my HP laptop, but due to their allow list, it does not start... but it's another story).

  Wifi works a treat, and I'm pulling in a little more speed of 100 mb/s (http://www.speedtest.net/result/2328501761.png) to connect to my router dual band 5 GHz.

  I understand this card features also the Bluetooth capabilities and I think that is where my problem comes from.

  I get a warning balloon will appear in the system tray saying "Device not recognized USB" (http://imageshack.us/f/208/intel62301.jpg/).

  I followed various supposed fixes, including the removal of the drivers, as you can see from the photo I've already done. As I'm under Windows 8 Pro 64 bit as soon as I restart the WLAN driver is automatically re-established.

  I tried to install the drivers several times, but I always get the error message as below: -.

  http://ImageShack.us/f/41/intel62302.jpg/
  http://ImageShack.us/f/822/intel62303.jpg/

  I'm looking for one of the 2 solutions.

  1. get the device working properly - Bluetooth & Wifi - there Toshiba never do drivers for the 6230?
  2 disable the ToolTip of the USB, I can do this as a stop, but as soon as I reboot it is back bothers me!

  Any help is appreciated with gratitude.

  Hello

  I m bit confused.
  Your problem is the message: saying 'USB device not recognized '.
  Right?

  Why do you as his associates to the new wireless network card?
  I checked the screenshot you posted above and card WLan (Intel Centrino Advanced N 6230) appears in Device Manager then its recognized by Win 8, thus

  On BT taken in charge by the Intel card.
  I found this software Intel® PROSet/Wireless Bluetooth for Windows 7
  TM http://downloadcenter.Intel.com/Detail_Desc.aspx?agr=Y&DwnldID=21713&Keyword=Bluet & lang = fra
  Normally it should work with Win 8 too.
  Maybe what you are looking for.

• Z820 with LSI 2308 sas controller will not publish with intel PCIe SSD installed.

  Z820 with LSI 2308 sas controller will not publish with intel PCIe SSD installed. The system works fine with Sata 600 pro SSD for windows and WD 4 TB Black seagate for storage. When the Intell 900 PCIe SSD drive is installed the system hangs at the LSI Mini OROM screen remains white. is there a way to put the LSI controller to jump the PCIe slots for boot devices?

  2 X Xeon 2695, 64 GB Ram, graphics Nvidia Quadro K5000, 2 X Intel 10 GB Ethernet card.

  Thanks for the reply. In fact I've disabled the LSI controller and connected to the integrated SATA controller and the Z820 starts and works perfectly with the PCIe SSD installed.

  Thank you.

• Elgato EyeTV - I copied my recordings on another external hard drive, assigned to this disk as the location of the Archive, restarted the computer, but the location of unpublished/are not recognized. (End of 2006 Intel iMac / OSX 10.7.5 Lion)

  Elgato EyeTV - I copied my recordings on another external hard drive, assigned to this disk as the location of the Archive, restarted the computer, but the location of unpublished/are not recognized. (End of 2006 Intel iMac / OSX 10.7.5 Lion)

  What do you mean by "assigned to this disk as the location of the Archive" is this something to do with the software you use?

  The drive is formatted for Mac?  Menu go to menu, click Finder go > utilities > disk utility > click on external drives partition - format it sets out Mac OS X extended.   Otherwise, to save the files on the disk and ease than Mac OS

  

• EliteOne 800 G2: EliteOne 800 G2 NIC driver not recognized with Windows Deployment Service WDS

  Hello

  I have just taken receipt of 5 new HP EliteOne 800 G2 23 "no touch machines. All PC's are generally imaged using Windows Deployment Services.

  I downloaded sp72515.exe that is the Intel I219 NIC driver pack for Windows 7 64 bit and injected these drivers into Windows Deployment Service and updated the boot LiteTouchPE_x64.wim file. Windows reported it went slowly and the 6 drivers concerned are all showing loaded with so much success in WDS.

  

  

  Problem. When I PXE boot the Windows EliteOne 800 G2 pilot of the CARD is not recognized by the 800 EliteOne G2.

  Wizard error

  A connection to the deployment share (\ < servername > \Deploymentshare$) could not be made. The following network device did not have a driver installed. PCI\VEN_8086 & DEV_15B7 & SUBSYS_8058103C & REV_31

  Hello:

  The only suggestion I can offer would be to try the driver directly from Intel...

  The 2nd file listed on the left side of the page is for W7 x 64.

  https://Downloadcenter.Intel.com/download/18713/network-adapter-driver-for-Windows-7-?v=t

• HIS Radeon HD 4670 not recognized by Win 7

  OK, now that the S6500NX is finally installed with Win 7 Home Premium 32 bit, the only remaining obsticle becomes the system to recognize the video card: a HIS Radeon HD 4670 ("Itceq" AGP 8 X 1 GB of DDR3 memory). It is compatible with DirectX 10.1. I chose ' AGP/Onboard' in the Bios. I've been messing around with different versions of the driver catalyst of 9.x, 10.x to 12.4 (later). The driver seems to be without error, but the adapter or the driver is never automatically recognized by Windows. If I go into Device Manager and "update driver" manually, then select the driver Radeon HD 4670 WDM (not mobility one!), and reboot, the Device Manager has a yellow "!" and said that it has been disabled (all versions 9.x driver to 12.4 said that). I have tested the card in my Gigabyte Triton of K8 system (under XP SP3 but not on the network) and XP sees the card very well.

  Many tech sites (for example, TomsHardware.com) talk about this card and seems to be problematic for some facilities, emits some Catalyst driver, but by all accounts should be recognized by Win 7.

  When the adapter has been installed initially, Win 7 assigned adapter VGA Std 'graphics '. The monitor is an old Dell M782, who did not detected, but because it's using the adapter in windows Std no refresh values appears. hdwwiz recogise the adapter and select strives in hdwwiz shows only those from Intel.

  Issues related to the:

  1. Is this a problem with Win 7 or HIS or the driver Catalyst? (or some combo)
  2. This card is even compatible with Win 7 32 bit?
  3. What is an AGP bios on A7V8X - LA motherboard problem?

  Thanks in advance,

  Thom

  People,

  Not one night white, but close enough. After crossing scenarios and options, try different drivers and pieces of hardware, I found a solution. Problems with possible HDMI and its conflict with its edge (from Paul - thanks!) gave me the idea. I also found the driver AMD AGP hotfix file.

  When I started this process, install Win 7 Home Premium 32-bit on a new HD in a S6500NX I did with the Creative Sound Blaster installed PCI (disabled people onboard in the bios) and the 4670 HIS HD Radeon Itceq AGP 8 X graphics card installed (AGP / enabled in embedded bios). I knew that I had to install a separate driver to get the new 4670 to work with Win 7 (from the list of compatibility with MS). I've always done the express installation. Because the card has never been recognized automatically and manually select a driver always gave place to a yellow '! ' in Device Manager, I have assumed that the existence of a conflict, but didn't know where to start. Reading the various posts here and elsewhere, brought me to believe it was a problem of cpu/bios/agp. It was not, well not quite, at least not the mobo directly.

  I suspect that the conflict was with the device IRQ audio and HDMI sound IRQ, but it is also a matter of AMD AGP with the driver. Once I found the driver 12.3 hotfix (12.4 pilot btw does not work either) AMD, I decided to do a custom installation and do not check the HDMI Audio option (so it should not be installed). Now, at this point, I had taken on the Sound Blaster and always had the sound edge off, so no sound, but has not removed the Creative drivers. Rebooting the system after installation of the driver of 12.3 hotfix for the HD 4670 (without the HDMI sound) Windows 7 recognized the graphics card! The Catalyst Control Center worked, graphic refresh rate and the monitor are now available: everything worked!

  Now, sound. I reinstalled the Sound Blaster card and booted up the system. It worked also. The system is now complete! Ecstatic!

  I'm exhausted. I suspect that the problem is somewhere in the allocation of resources for audio devices, simply not ready to everything tear and test this theory (i.e., re-installation of the verified audio HDMI driver AMD should lead the 4670 is not recognized due to a conflict with the sound card or indeed integrated sound card). In addition, there was the problem with AMD and AGP drivers.

  I finished.

  However, one thing still (somewhat) bothers me: why is there never a Compaq/HP logo at startup (no option in the bios to disable/enable) given that in all likelihood, it would take... This is the life. Maybe it has something to do with "service packs" (whatever they are - jk) and the 'care' of Compaq/HP files (could care less).

  Thom has left the building - good day to all.

  Blessings to all,

  Thom

• 3 TB Canvio Stor.E not recognized correctly in the USB 3.0 port

  I have four of the HDWC130EK3J1 external Stor.E Canvio Desktop HDDs.
  If more than one USB 3.0 drive is connected the partitions are not recognized.

  The GPT partitions are displayed as MBR partition protection.
  The MBR partitions are displayed as never applied.

  The drive is detected correctly after that he was to reinsert and close ofd.
  At the same time, only 1-3 partitions are recognized correctly.
  This problem can be reproduced 8.1 running Win and Win 7 64 bit using two different computers, by using the USB Intel and Nec controller.

  Currently, BIOS, update driver update. The HDDs are checked to find errors.
  Is there an update to flash ready or a replacement for the external hard drive option?
  Please note that a replacement with the same model makes no sense.

  My German Embassy has been blocked so I translated it. Sorry the only translator Google

  There could be a simple answer to this problem:
  There are two standards different MBR and GPT partitions.

  MBR works with drives up to 2 TB in size, but it can record handle t with more than 2 TB of space. MBR also only supports up to four primary partitions if you want more, you have to do one of your primary partitions an extended partition and create logical partitions inside.

  GPT (GUID Partition Table) is a new standard which replaced the MBR. The TPG requires UEFI. This standard isn't limited like MBR and readers can be much larger and size limits depends on the system and its file systems. It allows an almost unlimited amount of partitions.

  I guess that the system cannot recognize the partitions (from additional external HDD) due to the limitation of the MBR.

• HDD and dvd are not recognized in the configuration menu, what could be the problem?

  The hard drive and dvd drive are not recognized on the configuration menu for my desktop Pavilion a4316f.  What is a controller failure?  A PCI controller can be used to replace the motherboard controller?

  dhobs,

  Anguish, that the suffering of the faulty motherboard has been aggravated by your actions. Why you decided to perform a restore (which re - formate the disk, erase all your data files (documents, photos, videos to misic,) is really amazing.)

  You had a viable BONE, work and the data store. You he clobbered with recovery. As explained, the 'tattoo' reads the embedded hardware configuration and will stop at the resumption of treatment if it detects a change.

  Only temporary help I can offer is to open the computer case and install a small 12v on the NVidia chip fan. IF the chip is not 100% burned, you can earn low enough time to reinstall the operating system and then add the map.

• Installation of XP Prof on Tecra A9 PTS52E - SATA HDD is not recognized

  Hi all

  I have a "nine" Tecra A9 (PTS52E) with Vista Business installed. However, I need XP Prof and a CD of XP - SP2 slipstreamed. The SATA drive is not recognized XP installation, so I need a driver of "F6."

  There are a lot of howtos on this for the 945 chipset, but I couldn't solve this problem on my A9 (Mobile 965 Express Chipset). I don't want to buy a USB floppy for one-time-installation drive. So I have to build the driver (iastor.sys and more) in the XP installation disc.

  A few problems: there seems to be no easy way to do this, because intel only provides files *.inf for the ICH8R (RAID =) controller, which does not exist in the A9. So I have to change the *.inf files, correct?

  Another thing: I saw in an another post here the discussion on switching to AHCI in the BIOS in compatibility mode. I can't find a way to change this setting.

  Aargh, I need this laptop for my work on an A8 (which is also mine), I installed XP without any problem.

  Can anyone help?

  Thank you

  Michael

  Post edited by: michael-cologne

  Nice info I m interesting in the XP installation process.
  It would be great if you could post a few steps.

  Thank you

• Network controller is not recognized on Satellite A100 Windows XP

  Hi all!

  I bought a Satellite A100 PSAAR and I did a clean install of Windows XP on it. I installed all the drivers in the correct order (downloaded from the support page) but I still have a problem:

  Ethernet controller and network controller appear with a yellow exclamation point in Device Manager, and they are not recognized. I have downloaded the driver lan and I managed to do recognize the ethernet controller. However no matter how hard I tried, I can't find the correct driver for the NETWORK CONTROLLER, which still appears in Device Manager in yellow color.

  I really could use any help here... Thank you in advance.

  Hello

  Shouldn´t be a big problem to get some drivers for your machine's real lan. Just go here:

  http://www.Intel.com

  and download the intel proset for ethernet controller. If you didn t already installed the wireless card, do so. Otherwise the other network controller could be the bluetooth adapter.

  It would be nice to hear from you...

  See you soon

• Satellite A10 - recovery disk not recognized

  I want to format my hard drive and reinstall windows xp.

  Of course, I have Toshiba A10 laptop with HDD 160g, 1 g of Ram, cd/dvd player and the restore disc (cd).

  Problem: the restore disc is not recognized by the cd player. When I insert the disc, then again, boot sequence goes to hard drive and boots from there

  What I did:
  1. check if the reader sees another s cd. Answer Yes, Yes
  2 boot sequence of the bios checked as well as toshiba consoles set up made sure it is
  in "order"hdd, lan, floppy, cdrom", (I tried other combinations starting with cd as well).
  3. I cleaned the restore disc, didn't work
  4. I ordered another set of Toshiba restore disk, which did not work either, still not recognized
  5. I bought a cd/dvd external reader believe it or not, disc starts to work in this case, I get a warning screen shows all data will be lost and asks me to click if I want to continue, when I click it says will now restart the computer and it does but comes back and goes back on the hard drive and boots from there.

  I must also add; When I switch on I get "' pxe e61 media test failure, mof outgoing intel boot agt" msg, according to my search, this problem indicates hard disk.
  but my hard drive does not work,

  Will someone give me an advice?

  If the BIOS is set to boot from the local network first, before trying to boot from the HARD drive, you will see the error PXE.

  Have you tried to clean the lens in the DVD player? Wipe with a Microfiber cloth.

  try holding down "C" when you turn on the laptop, this will make it boot from the CD.

• Floppy USB drive not recognized when installing WinXP on Satellite Pro L40

  History:

  I bought a Satellite Pro L40, it came with windows vista. I can't stand vista windows for obvious reasons. so I formatted the HARD drive. I have a copy of windows XP.

  IV ' e read on the internet that I need Intel storage driver manager...

  IA´ve got the driver, he got on a floppy, and it does not, because when I start to install XP, it works (after pressing F6 & choose the driver to install). I come to the part of license agreement, press F8 accept...

  I select the partition I want to use (in format completely on vista). It starts to load more stuff... so he said "PLEASE INSERT LABELD - INTEL MATRIX STORAGE MANAGER DRIVER - DISK IN DRIVE A:" "PRESS ENTER WHEN READY."

  The disc that I used in the first place is always in. when I press on enter, nothing NOT to PAST (the USB floppy drive is not yet into action)

  How can I make it work? It is that I can get.

  I DON'T WANT BACK TO VISTA - HELP!

  This could happen if the floppy USB doesn t drive supports the standards of law. Some people have reported on different websites many floppy drives are not recognized.

  However, worry guy. I have a solution ;) (jeaaa: D)

  Try to create a new XP CD using the software called nLite!
  Then, you could include the SATA (Intel Matrix Storage Manager) driver in this new CD and then you could boot from the XP CD again.

  For details and how to use the nLite please Google because there are a lot of useful Web sites.

  Good bye