Inter routing VLANs with this config

Similar Questions

• I have a Macbook Pro mid 2012 edition, i7 and 8 GB (2 x 4 GB) of RAM DDR3 (1600 MHz). Can I add any RAM with this config?

  I want to upgrade my RAM 16 GB (2x8GB) and also to change the hard drive (750 GB) to a 250 GB SSD. I was going through the forum and people have posted that they have improved their RAM with no problems. I visited the local electronics market and is the knowledge that they have a Kingston 8 GB DDR3 1600 MHz RAM. I just want to know if it is safe to add that RAM for my MBP or not? One of my friends told me that the MBP requires a different sort of RAM so I am confused. In addition, I was intending to buy a single 8 GB and set up my MBP with 12 GB (8 + 4) RAM and then replace the other 4 GB with an 8 GB to make eventually 16GB. Will there be a problem with this approach? Also can I add any SSD fits laptops from my system? I found an SSD 240 GB (uv300) Kingston. Please suggest if I can add that.

  You can fit a maximum of 16 GB, if you choose compatible Ram.

• help config VLANs and inter routing VLANs on SF - 300

  Hi all.

  I divided the routing problem "SF-300 (Layer 3) can be connected to the bridge." I did not put in the entry door. Too bad, I have encountered with Packet Tracer 5. I can attach a file. Leave everything to me.

  Thank you.

  # config - code

  IP routing

  VLAN 10

  VLAN 20

  VLAN 30

  interface FastEthernet0/1

  switchport access vlan 10

  switchport mode access

  interface FastEthernet0/6

  switchport access vlan 20

  switchport mode access

  interface FastEthernet0/11

  switchport access vlan 30

  switchport mode access

  interface Vlan10

  IP 192.168.10.1 255.255.255.0

  interface Vlan20

  address 192.168.20.1 255.255.255.0

  Vlan30 interface

  192.168.30.1 IP address 255.255.255.0

  The configuration of the switch is fine. My only question is your computers. Example of

  Computer on fa1.

  Should be something like

  192.168.10.100

  255.255.255.0

  192.168.10.1

  Computer on Fa6

  192.168.20.100

  192.168.20.1

  255.255.255.0

  Also avoid any simultaneous wireless connection and you may want to disable things like firewalls of the window.

  -Tom
  Please mark replied messages useful

• Voice VLAN with SRW224G4P

  Hi all

  I tried to config a vlan voice in this switches for the last 3 hours and for me it's impossible... I know how to do it in a switch IOS but with this switches is a nightmare...

  I have this topology

  PC - telephone to IP - SW1 SRW224G4P - SWCORE SRW2024 - router 2921 CME

  I have this config in my router,

  interface GigabitEthernet0/0

  no ip address

  automatic duplex

  automatic speed

  !

  interface GigabitEthernet0/0.1

  LAN description

  encapsulation dot1Q 1 native

  IP 192.168.5.95 255.255.255.0

  IP virtual-reassembly in

  !

  interface GigabitEthernet0/0.100

  Description VLAN VoIP

  encapsulation dot1Q 100

  IP 192.168.251.1 255.255.255.0

  IP virtual-reassembly in

  !

  SW1 created the VLAN 100 and activated as VLAN VOIP

  The first 3 octes for the mac on my phone is inserted into the Table YES telephony

  Belonging to a VLAN automatic voice is enabled in the port where the phone is attached.

  The port connected to the SWCORE has the vlan configured as labeled 100.

  SWCORE has created the VLAN 100 and activated as VLAN VOIP

  The port connected to SW1 has the vlan configured as labeled 100.

  The port connected to the router CME has the vlan configured as labeled 100.

  If I have another config port in SWCORE with 100 VLAN Tag I can ping from FMC to this host.

  Could be the problem, an error of spread vlan?

  Could someone help me? I'm desperate...

  Thank you in advance.

  Hi David,

  Thank you for the purchase of the switch.

  . Like what, even riding a bike, the switch is actually very easy to set up, if you practice on it...

  You mentioned that you use the 'phone YES picture' I assume you have a SF300 - 24 p or p/n command SRW224G4P-K9-NA.  Please be specific with the models of switches you use.

  Using the old SRW series or refreshed in the kernel SRWxxx-K9 (300 series) switch?

  First of all, make sure that you are using version 1.1.0.73 of the switch firmware. This change now or check that 1.1.0.73 is the active image on the switch.

  The switch has two areas to store the firmware images.  It stores the new firmware in the area of the image unused.  The administration for the firmware update Guide and select new firmware for the next reboot.

  CDP is enabled on the switch when using the new software, did not exist with older firmware, where my insistence to upgrade the firmware.

  ( Personally I would prefer that you have a role of catalyst for switching to your CME ISRG2 application, for purposes of support tech.) But this is the land of freedom..)

  I found the following when I added my SG300 - 28 p to a conscious UC500 of VLAN.

  The UC500 was vlan100 of advertising as a vlan voice, configured by Cisco Configuration Assistant, you could try CCP on your ISR.

  I got an IP phone that is plugged into the port of switch in the G7 and uplink to my UC500 via the Gig27 port.

  What follows in blue is a screenshot of my 300 series switch CLI interface.

  You will notice that the switch already filled both VLAN and port information, the only command that I added was "don't activate any complexity of passwords" and some usernames, including free from the screenshot below.

  the configured basically switch itself.

  -See the establishment of the system-

  Description of the system: 28 ports Gigabit PoE managed switch

  System of the time (days, hours: min: sec): 00, 00:12:04

  Contact system:

  Name of the system: switch4cf17c

  System location:

  System MAC Address: d0:d0:fd:4 c: f1:7 c

  System object ID: 1.3.6.1.4.1.9.6.1.83.28.2

  Fans Status: OK

  -See the version-

  SW version 1.1.0.73 (date, June 19, 2011 time 18:10:49)

  Start the version 1.0.0.4 (April 8, 2010 time 16:37:57)

  HW version V01

  Location of activity IP gateway Type.

  ----------------------- ----------------------- --------

  192.168.10.1 active dhcp

  IP address I / F Type of status

  ------------------- --------- ----------- -----------

  192.168.10.17/24 vlan 1 DHCP valid

  -show ipv6 interface-

  IPv6 is disabled on all interfaces

  -show running-config-

  interface gigabitethernet7

  Storm-control broadcast level 10

  output

  interface gigabitethernet7

  Storm-control include multicast

  output

  interface gi27

  point to point spanning tree-type of link

  output

  database of VLAN

  VLAN 100

  output

  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___

  Add a voice vlan Yes-table 00036 b Cisco_phone___

  Add a voice vlan Yes-table 00096e Avaya___

  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___

  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone

  Add a voice vlan Yes-table 00d01e Pingtel_phone___

  VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075

  Add a voice vlan Yes-table 00e0bb 3Com_phone___

  hostname switch4cf17c

  No complexity of passwords allow

  No server snmp Server

  interface gigabitethernet7

  macro description ip_phone_desktop

  output

  interface gigabitethernet27

  description of the macro "pass | valeur_log | switch ".

  output

  interface gigabitethernet7

  ! next order is internal.

  macro auto smartport dynamic_type ip_phone_desktop

  switchport trunk allowed vlan add 100

  output

  interface gigabitethernet27

  ! next order is internal.

  switch dynamic_type macro auto smartport

  switchport trunk allowed vlan add 100

  output

  switch4cf17c #sh cdp nei

  Ability code: R - router, T - bridge Trans, B - road Source bridge

  S switch, H - host, I - IGMP, r - Repeater, P - VoIP phone

  M - managed remote-device, C - CAST phone Port,

  W - two port MAC relay

  Device ID Local time from Port platform capacity ID Adv

  The interface direct worm.

  ----------------- ----------- ---- ------- ---------- ------------ -----------

  SEP503De50F133A gi7 2 158 H P CISCO IP eth0

  Phone

  SPA525G2

  68bdab0fdcfd gi27 2 169 S I Cisco SG gi9

  300 10 P

  (PID:SRW2008P - K9) - VOD

  switch4cf17c #sh vlan

  VLAN name Ports type permission

  ---- ----------------- --------------------------- ------------ -------------

  1 1 article gi1-28, required to Po1 - 8 by default

  100 100 gi7, required permanent gi27

  Automatically numbers which ports need to be listed in VLAN 100.

  I did not switch it was connected to VLAN100. I don't have add vlan100 to the database for VLAN.

  Get the ISR router to announce VLAN100 as a vlan voice.

  Best regards, Dave

• two questions of routing VLAN fast

  Let's say that I have spend a routing 4 L3 VLAN

  VLAN 1 192.168.10.0/24, virtual interface of the switch is 192.168.10.254 inside this vlan
  VLAN 2 is 192.168.20.0/24, the virtual interface of the switch is 192.168.20.254 inside this vlan
  VLAN 3 is 192.168.30.0/24, the virtual interface of the switch is 192.168.30.254 inside this vlan
  VLAN 4 192.168.40.0/24, virtual interface of the switch is 192.168.40.254 inside this vlan

  There is that a single router out of this switch at the net, and lets say that it is in VLAN 1 and its address is 192.168.10.1

  first question - inside the L3 switch I need to add a default route 0.0.0.0 0.0.0.0 192.168.10.1

  to ensure that all traffic not matching only a 192.168.x.x address not know where to go to the net, correct?

  Second - when this router, is there a difference if I use the following static route:

  192.168.20.0 255.255.255.0 192.168.10.254

  Instead of

  192.168.20.0 255.255.255.0 192.168.20.254

  ?

  Whatever happens, the package comes to switch L3, but in one case, what happened to it through the interface VLAN 1 VLAN and in the other case, he gets there through the interface VLAN VLAN for which traffic is intended anyway. is what im trying to figure out, this will make a difference at all? especially with regard to broadcast packets?

  If it makes no difference, then it is safe to say that the following static route would be optimal?

  192.168.0.0 255.255.0.0 192.168.10.254

  Re "of all". Fix. The L3 switch will route traffic based on its routing table. By default, he knows all IP subnets, it is directly connected to, i.e. all subnets VLAN. If you must add a route by default manually or not depends on the exact implementation. It would be nice if the L3 switch will use the no default for routing gateway that you use for the switch IP parameters itself (if there is an option in the web interface to set a default gateway). If you cannot define a default gateway on the L3 switch, you might have to manually add a static route. The easiest way would be to check the current routing table and see if there is a default or not gateway.

  Re "then." A router can only transfer the packets to the next hop router. The next hop router must be connected to this router. The route "192.168.20.0 255.255.255.0 192.168.10.254" is correct for a router with IP address 192.168.10.1 and 255.255.255.0 as 192.168.10.254 subnet mask is connected to the router. "192.168.20.0 255.255.255.0 192.168.20.254" is not correct. The router cannot learn the path to a subnet specific 192.168.20.0/255.255.255.0 using a gateway on that subnet. It is not correct to use this kind of a route and do not use it even if it might work even (because the router is a simple query ARP to find the MAC address of the 192.168.20.254 and your L3 switch will respond to the ARP request, even if it's on the internet of 192.168.10.254). At the same time that another router between 10 and 20 subnets it would work no more...

  Re your conclusion: I recommend to keep four static routes to subnets existing on the L3 switch instead of put in a single subnet more great which includes a lot of addresses that are not connected here. Technically, this works if you only use working IP addresses. But you will see some loops if you send something to 192.168.55.50 or similar. The gateway router it will send to the L3 switch that will return to the catwalk. They should understand it's a loop, but still, I would not recommend this type of installation... Add routes for each of the L3 switch subnet...

• The problems of routing VLAN?

  Hello

  I'm trying to get our network out of a topology of flat to work with the hardware I have on the spot I have setup the network and local networks virtual, but could not get any other VLAN to carry. Here is what I use:

  Reference Dell PowerConnect 6248 as my router from Layer 3 and three PowerConnect 2748 detach the 6248 in three GAL groups all with four ports together. I have VLAN 10-50 for various average things regime 192.168.10.0/24, 192.168.20.0/24, 192.168.30.0/24 ect.

  Here's the question: 10.0 network works fine, but on any other VLAN, I get an IP address from the DHCP server, but I can't ping my gateway let alone ping another VLAN.

  Heres my living room will be output:

  console#show run
!Current Configuration:
!System Description "PowerConnect 6248, 3.3.11.2, VxWorks 6.5"
!System Software Version 3.3.11.2
!Cut-through mode is configured as disabled
!
configure
vlan database
vlan 5,10,20,30,40,50
vlan routing 20 1
vlan routing 30 2
vlan routing 40 3
vlan routing 50 4
vlan routing 1 5
vlan routing 10 6
exit
stack
member 1 2
exit
ip address 192.168.6.6 255.255.255.0
ip default-gateway 192.168.6.1
ip address vlan 5
ip routing
ip route 0.0.0.0 0.0.0.0 192.168.1.1
interface vlan 1
routing
ip address 192.168.1.2 255.255.255.0
exit
interface vlan 10
name "Servers"
routing
ip address 192.168.10.1 255.255.255.0
bandwidth 10000
ip mtu 1500
exit
interface vlan 20
name "Production"
routing
ip address 192.168.20.1 255.255.255.0
ip helper-address 192.168.10.110
exit
interface vlan 30
name "WD Staff"
routing
ip address 192.168.30.1 255.255.255.0
exit
interface vlan 40
name "Non WD Offices"
routing
ip address 192.168.40.1 255.255.255.0
exit
interface vlan 50
name "Church"
routing
ip address 192.168.50.1 255.255.255.0
exit
username "misterp" password beda28c8e29f04603da19eb1b3b239ee level 15 encrypted
!
dhcp l2relay vlan 20
dhcp l2relay circuit-id vlan 20
dhcp l2relay remote-id 1 vlan 10
dhcp l2relay remote-id 20 vlan 20
!
interface ethernet 1/g1
switchport access vlan 10
exit
!
interface ethernet 1/g2
spanning-tree portfast
switchport mode general
switchport general allowed vlan add 20,30,40,50 tagged
exit
!
interface ethernet 1/g3
channel-group 1 mode on
exit
!
interface ethernet 1/g4
channel-group 1 mode on
exit
!
interface ethernet 1/g5
channel-group 1 mode on
exit
!
interface ethernet 1/g6
channel-group 1 mode on
exit
!
interface ethernet 1/g7
channel-group 2 mode on
exit
!
interface ethernet 1/g8
channel-group 2 mode on
exit
!
interface ethernet 1/g9
channel-group 2 mode on
exit
!
interface ethernet 1/g10
channel-group 2 mode on
exit
!
interface ethernet 1/g11
channel-group 3 mode on
exit
!
interface ethernet 1/g12
channel-group 3 mode on
exit
!
interface ethernet 1/g13
channel-group 3 mode on
exit
!
interface ethernet 1/g14
channel-group 3 mode on
exit
!
interface ethernet 1/g15
switchport mode trunk
switchport trunk allowed vlan add 10,20,30
exit
!
interface ethernet 1/g16
switchport access vlan 10
exit
!
interface ethernet 1/g17
switchport access vlan 10
exit
!
interface ethernet 1/g18
switchport access vlan 10
exit
!
interface ethernet 1/g19
switchport access vlan 10
exit
!
interface ethernet 1/g20
switchport access vlan 10
exit
!
interface ethernet 1/g21
switchport access vlan 10
exit
!
interface ethernet 1/g22
switchport access vlan 10
exit
!
interface ethernet 1/g23
switchport access vlan 10
exit
!
interface ethernet 1/g24
switchport access vlan 10
exit
!
interface ethernet 1/g25
switchport access vlan 10
exit
!
interface ethernet 1/g26
switchport access vlan 10
exit
!
interface ethernet 1/g27
switchport access vlan 10
exit
!
interface ethernet 1/g28
switchport access vlan 10
exit
!
interface ethernet 1/g29
switchport access vlan 10
exit
!
interface ethernet 1/g30
switchport access vlan 10
exit
!
interface ethernet 1/g31
switchport access vlan 10
exit
!
interface ethernet 1/g32
switchport access vlan 10
exit
!
interface ethernet 1/g33
switchport access vlan 10
exit
!
interface ethernet 1/g34
switchport access vlan 10
exit
!
interface ethernet 1/g35
switchport access vlan 10
exit
!
interface ethernet 1/g36
switchport access vlan 10
exit
!
interface ethernet 1/g37
switchport access vlan 10
exit
!
interface ethernet 1/g38
switchport access vlan 10
exit
!
interface ethernet 1/g39
switchport access vlan 10
exit
!
interface ethernet 1/g40
switchport access vlan 10
exit
!
interface ethernet 1/g41
switchport access vlan 10
exit
!
interface ethernet 1/g42
switchport access vlan 10
exit
!
interface ethernet 1/g43
switchport access vlan 10
exit
!
interface ethernet 1/g44
switchport access vlan 10
exit
!
interface ethernet 1/g45
switchport access vlan 10
exit
!
interface ethernet 1/g46
switchport access vlan 10
exit
!
interface ethernet 1/g47
switchport access vlan 10
exit
!
interface ethernet 1/g48
switchport access vlan 10
exit
!
interface port-channel 1
spanning-tree disable
spanning-tree mst 0 external-cost 5000
switchport mode general
switchport general pvid 10
switchport general allowed vlan add 10
switchport general allowed vlan add 20,30,40,50 tagged
switchport general allowed vlan remove 1
exit
!
interface port-channel 2
spanning-tree disable
spanning-tree mst 0 external-cost 5000
switchport mode general
switchport general pvid 20
switchport general allowed vlan add 10
switchport general allowed vlan add 20,30,40,50 tagged
switchport general allowed vlan remove 1
exit
!
interface port-channel 3
spanning-tree disable
spanning-tree mst 0 external-cost 5000
switchport mode general
switchport general pvid 10
switchport general allowed vlan add 10
switchport general allowed vlan add 20,30,40,50 tagged
switchport general allowed vlan remove 1
exit
exit

  As a side note, I don't have really messed with other VLAN only 20.

  Any help would be great. I'm just puzzled.

  Thanks Daniel, I understand this problem. on the 27xx series switches I was marking traffic on clients without realizing it was not labeled. New network equipment in collaboration with a Cisco and DELL all this background I've ever had to deal with THIS a marking was done automatically.

• 2600 router: faced with setting up the accounts user and AAA

  I use SDM to configure easy VPN connection and being a newbie I'm fighting with AAA and the creation of the necessary user account. The SDM Assistant said I must have active AAA and a user account. I found this doc from Cisco using google:

  http://www.Cisco.com/en/us/docs/iOS/12_2/security/configuration/guide/scfathen.html#wp1000971

  and following the instructions, I entered these commands in the cli:

  Router (config) #aaa new-model

  Router (config) #aaa authentication login default local

  but my normal connection and the user name and password do not work in the CLI as soon as I did it. I have the router powerdown and restart it to retrieve the control.

  To be honest, I found things really hard Cisco instructions, I don't understand method-list RADIUS Kerberos GANYMEDE stuff so I was wondering if there was simple instructions there to set up the user account necessary to go forward with the vpn Wizard easy in SDM.

  Thanks for the pointers.

  Hello Anthony,.

  Once you enable the aaa new-model, all applied to the invalid lines previous authentication mechanisms. That's why you should do one of the following values

  Do not issue 'aaa authentication login default local' or if you are forced by SDM, or create a username for yourself with high private, because this command will effect console or VTY lines that their authentication is left by default and require the username and password each time you connect, or you can create a list that has 'no' as a method and apply to the console line to ignore the console authentication.

  username anthony priv 15 password xxxx

  Once you enter a username as shown above, you can connect via the console with this username and pass if "aaa authentication login default local" is issued.

  RADIUS and Ganymede methods are servers that has the ability to contain the names of users with more advanced configurations. For simple authentication, you can use local authentication, this is why you should not mess with Radius or Ganymede at the moment.

  Concerning

• message keeps coming up ' is a problem with this Web page then it has been reloaded.

  My woman keeps getting the message on his ipad when she tries to use the internet "is a problem with this Web page then it has been reloaded. What happens whenever she tries to go to a Web page. It all started last night when she tried to open a file attached to an email zip. Could not be linked. What should she do?

  Do a restart forced his iPad: press and hold the home button and sleep, wait for the Apple logo, release the buttons. While waiting for the reboot also restart the WiFi router by pulling on the power of him, wait a minute, then plug it in again.

• Satellite P100-160 refuses to connect to my router 3Com with WPA - PSK

  Help! My new laptop Toshiba refuses to connect to my router 3Com (f/w 2.06T13) model 3cWDR100A on WPA - PSK. The router only supports TKIP (no AES).

  The laptop, a Satellite P100-160 is under Vista Home Premium with the latest Intel 3945 11.5.0.32 driver and I tried the version of the site Web of Toshiba version mentioned in other threads (and a few other versions also).

  Either way, I don't like latest driver hit with content identical binary files and different date stamps or running of the anonymous installers that have not been digitally signed.

  The problem is that non-encrypted, or WEP works perfectly, but WPA - PSK is not. It fails with a diagnostic message 'timeout for secondary keys. The thing will be very occasionally connect to the network without a timeout (before I tried to improve things with the last pilot about 1 in 20 attempts after a reboot, now it comes rather from 1 to 100). If I can be sure that the password is correct. When it connects everything is fine and stable with excellent signal until the first suspended and then the connection is lost. It's more than a little irritating.

  I see several topics of doom similar networks to Vista support groups. They all seem to hinge around WPA - PSK TKIP and WiFi Intel chipset x 945 in combination with certain models of router. Please can anyone help solve this mess?

  I've seen other threads of networking in Vista by users with this specific Intel chipset and my router model having exactly the same problem and so far nobody has found a solution. I checked the basics of knowledge (MS & 3Com) and tried a few plausible fixes, but nothing helped. I'm out of ideas.

  It seems a little absurd to demote network security to make the latest PC works correctly. Dumping Vista (however tempting) is not an option.

  Thanks for any suggestions or diagnostics.

  Kind regards
  Martin Brown

  Hello Martin

  As you can see this is not Toshiba specific stuff and if there is no 'global solution' I don't really know what Toshiba should do about it. As you all know it should support hardware and software (driver), but if not I don't really see a solution for this.
  Who should offer a solution? Toshiba or Intel?  :|

• Can see router WLAN with Satellite A100 - PSAANE Vista

  Hello

  I have a satellite A100 PSAANE running Vista Ultimate that has trouble finding WIFI (atheros wlan card). The router is a Siemens gigaset transmitting the WPA2-PSK / WPA - PSK with dynamic channel assignment. In the past, I was able to get a wireless connection to my router with this laptop, but did find it difficult to detect the WIFI network sometimes.

  Location:
  Active wireless switch. Different WLAN of the A100 see whenever I update the list in Vista.
  Ever - at least most of the time that I do not see my own network.

  Other laptops running Windows XP however found my WLAN in these moments there.
  This implies a malfunction on the A100.
  Update (28/10) drivers for Atheros and Vista resulted in no w-network at all.

  Reset did not help. A reset of the router does not work nor the laptop next to the router of positioning.
  The failure of detection is a recurring event with this router.

  Currently the situation is that no WLAN is detected, then things got worse.

  Everyone has the same problems in a similar configuration?
  I feel that I might have a problem of material here.

  Thank you very much

  I had a similar situation with my two laptops Toshiba (new Satellite A200 and older Tecra M1). I was confused why the WIFI network is not visible the two notebooks. After a few reboots (laptop computers and router) I again was able to use the WLAN.

  I do not really understand what was wrong, but now it works again. Try the same thing. Stop the router for awhile and turn it back on.

• Flag 23: HP Pavilion 23 - USB Modem is not compatible with this version of Windows.

  I just got a message saying that the USB Modem is not compatible with this version of Windows. I use a wireless router. What's to worry?

  It is not the number of product that I asked.

  You can find it in a number of places.

  (1) BIOS--> information system tab

  (2) HP Support Assistant at the bottom of the window HPSA.

  If you do not experience a problem marketing online then is there really a problem at all?

  Check in the Device Manager to see if there is a peripheral usb modem it without a driver installed. If it's a real modem, as in for telephone line connection, it isn't something you need to worry.

• EA4500: There is a problem with this Web site's secure certificate.

  When I navigate to the Web page of the router, I get a message that "there is a problem with this Web site's secure certificate."

  I'm using https.

  Does this mean that https does not work on the EA4500?

  N °, this means that the browser does not trust the certificate sent by the router. The connection is always encrypted.

• WRE54G canmot associated not with this access point in Repeater mode.

  Hello

  Because of the concrete walls, I have a weak signal to use the WRE54G to extend my existing wireless network. However, I installed an Ethernet cable and found possible to connect the WRE54G access point. This is my extension of network is via a connection to an Ethernet cable. Is seems to work fine, it allows communications to the internet and shows a power good signal from a remote PC. But it works only in unsafe mode.

  Although I tried to reset, and then follow the instructions to set up a new WEP or WPA encryption, the installation program recognizes the WRE54G, but does not allow me to save the configuration.

  The error it says it is "WRE54G canmot not associate with this access point in Repeater mode.

  Help, please

  Make sure your router's wireless settings and WRE are the same. Try changing the channel on your router, if your router's wireless channel is the default after the procedure, your WRE is unable to communicate with your wireless router.

• Attempt to create overlay route map with...

  Hi all

  I am trying to create a route for the updated plan overlay direct semi. Currently, I'm trying to understand how the game a value in pixels in the command ForeignWindow transperant so I can draw my lines inside, then superimpose on mapview. It appers that the only possible pixel values available are between 0 and 255, which leads me to believe the transparency with this control is not always possible because with this limit, I can even clone the image under my control.

  Is there a way I can manually pull on any other control to achieve the desired effect?

  Kind regards

  -J

  Pixels have an RGBA value, where RGB is the color between 1 and 255, and A is the alpha value, carried out by Alpha Composition. For each pixel and it associated the pointer, R = [point], G = [pointer + 1], B [pointer + 2] = and a = [pointer + 3]. Focus on changing the alpha value of your pixels.

  On a side note, I tried to do a very similar thing on another project. I don't know that it is possible, in some way, with a bitmap image.

• Belkin router low with USB for storage drive and Windows 7 do not get along?

  Hi all!

  We have a Belkin N wireless router + with a USB stick 'slot' in the back with the rest of the cables. The USB option is actually the only thing that made me buy the router in the 1st place! Anyway, it does not work when connected to the router, even if the network is running perfectly. It is a Seagate external hard drive and when it is plugged it's high lights of the page, there is no power cable so that it can be plugged into the wall. NTFS system I think. I use Windows 7. I tried so many different things, trying to connect this dag on drive to the router, I've exhausted all efforts, it seems. On belkin under my model site there a Belkin Storage Manager, but there isn't even a request, is just a plateau that is located on the bottom of my screen, the only thing I can do for her, is shut, it is the only command that opens. Oh and the website says also I can enter my routers address in IE followed by a slash and the name of my seagate... the drive is H, so I tried different versions of H:, tried FreeAgentDrive, etc...

  .. I think it is a windows problem, b/c not only not Seagate turn on, under the watch USB (via IE, default routers page layout), the connected router settings. In addition to the light on the front of the router is 'active', blue and work.

  HM... I run windows 7 Professional / 64-bit / don't know not what other information I have to give... I don't think that the external hard drive would have it's own IP address when you are connected to the router... could it? Also, my service is comcast with dynamic IP address assignments... so it would not stay dry alike... correct?

  Oh, and the external hard drive works wonderful connected directly to my laptop and an XP computer at work... so router maybe not is not talking computer properly the drive... I should have some sort of security "allowances" on this drive until I put it on belkin?

  I'm sorry this is a NOVEL, someone help please? I've been addressed under and turned off for a year... I get very frustrated with this!

  : D

  Try changing the drive letter and y or X. mohanad