WRE54G canmot associated not with this access point in Repeater mode.

Similar Questions

• WiFi HP ENVY 4500 with several Access Points - same SSIS Configuration

  Hello

  We just got a HP ENVY 4500.  I have a main homenetwork with a wifi Modem/Router and an old router acting as an Access Point to the floor to extend coverage.

  Both have the same SSID and password and are set to different channels.

  My HP ENVY 4500 fails to connect when the Access Point is lit.

  It will connect with it.

  Once connected, I can turn on the PA and all is well.

  The two router an AP using WPA-PSK/WPA2-PSK encriptación

  The router (that it connects to) should have a better sgnal when both are on, so I do not understand why they need the AP to be turned off to connect.

  Any thoughts people?

  Eserim

  I think he has always had problems with several access points.  Try this, what ever AP is closest to the printer, set it to channel 1.  Then try channel 11.  Try now.

• Impossible to access wifi with other access points

  WNDR4500v3 with firmware V1.0.0. I32

  I bought this router on dec 25 2015 to replace a dead linksys router.
  The router feeds a switch of 16 points from one of the 4 ports.
  I have a win 7 pc connected to one of the other routers 3 ports.
  Then a VoIP connected to port 3 of the router.
  I have 2 other wireless access points connected to the port 16.
  We feed a remote building through a wired connection to the firset access point
  The other access point is also fed by a wired connection.
  The old linksys router had him for 4 years.

  As I said I bought this router as a replacement... but since its worthless and the two wireless access point do not have internet connection.
  So either I get it work or will return it for a refund within 24 hours.

  Figured that out it was Network Manager and windows share the unknown connection of marking.

  In advanved sharing setting I have to change to use for user accounts and passwords to connect to other computers

  Then all the problems went away.

  No more giving up connection and with no internet connection.

• WAP54G Access Point using wireless mode, but not worked. :(

  I bought today WAP54G.
  My son and I have PC but we distance between our room each other and
  wireless signal is not strong enough sometimes.
  My son has wired Internet w / WRT54GS router and I have wireless
  USB G adapter to my room.
  Cat w / Linksys rep, the other day and he recommended buying WAP54G and I could leave this AP @ salon and do not need to have the connection cable.

  Anyway, I don't know how to install this customer service, called today
  and she told me that I need to install the CD in my computer. But there is no
  connection by cable or router and I cannot install CD in my computer.
  So, I installed the CD in the PC of my son who has wired Internet and
  router. The installation has been completed.
  After the installation, turn off AP and move on to the living room.
  Then, there is no "link" light on. Lamp only Power and act on.

  Tried chat w / online but offline and it is really difficult to chat w /.
  them.

  Please let me know:
  1. can I use this without wired access point?
  I would like to implement the AP @ living room (between my son and my room)
  2. which PC do I need to install CD? But once again, my PC have no cable
  connection and cannot install the CD.

  I am very beginner wireless and PC so please tell me step by step.
  I read manual and I used the installation CD Wizard but still do not work.

  Please someone help me.

  I think that you must configure your AP as Repeater wireless... Follow the link here , make sure that when you set your Access Point to the "Wireless Repeater" mode, this device will communicate only with a different Access Point Linksys (WAP54G) and wireless G of Linksys (WRT54G) router...

• Intel WiFi Link 1000 bgn @ E220s: visible, but will not connect to access point

  Hello

  just got my new E220s - love it! Only problem is that I can see the wireless access points, but whenever I try to connect to them it says: "Windows could not connect to '.»»

  My setup is a Lenovo TinkPad E220s: Intel Core i5, Intel WiFi Link 1000 bgn, Bluetooth 3.0, 7200 RPM 320 GB HDD, 4 GB RAM, Windows7 Home Premium.

  My system is up to date with regard to the update of Windows and Lenovo BIOS update.

  * A tried to connect to a FritzBox 7141 (b, g, g ++ standards)

  * with WPA - PSK: entered the password-> problem as above

  encryption-> problem as above

  * Connection I tried with 'eduroam' (wifi popular education in the world)-> problem as above

  * Using the driver Lenovo 14.0.1-> problem as above

  * Manually install driver Intel 14.1.1.3-> problem as above

  'Manual Diagnostic tool' Intel:

  * test hardware: past

  * pilot: past

  * radio test: past

  * scan test: past

  * association test: failed

  * other tests: does not work

  Some diagnoses more Windows:

  Details about network adapter diagnosis: Network adapter Wireless Network Connection driver information: Description . . . . . . . . . . : Intel(R) WiFi Link 1000 BGN Manufacturer . . . . . . . . . : Intel Corporation Provider . . . . . . . . . . . : Intel Version . . . . . . . . . . . : 14.0.0.113 Inf File Name . . . . . . . . . : C:\Windows\INF\oem14.inf Inf File Date . . . . . . . . . : Tuesday, November 09, 2010 8:43:32 AM Section Name . . . . . . . . . : Install_MPCIEX_Lenovo_1000_HMC_BGN_WIN7_64 Hardware ID . . . . . . . . . . : pci\ven_8086&dev_0084&subsys_13158086 Instance Status Flags . . . . . : 0x180200a Device Manager Status Code . . : 0 IfType . . . . . . . . . . . . : 71 Physical Media Type . . . . . . : 9

  Hello

  Problem solved. Of wire antennas was not of all attached to the card and the other it has established relationships by chance. It took me 3/4 of an hour to turn off the battery, remove the keyboard, attach wires to the NIC (quite difficult due to lack of space) and put it all together. Then everything worked fine.

  Thanks for the help, forum!

  E220s rocks!

• Problem with internet access point

  Hello, I saw that this question was asked before, but has never seen a solution to my problem, I will explain:

  I have like 5 months with this problem. I have a TP-LINK 300Mbps Wireless N Router, model No. TL-WR841ND. The fact is that when I plug in my router to the Modem, my wireless network seems to work fine, but when I try to connect to my computer or any other device to the network (mobile phones, playstation 3, tablets, etc.), I am unable to do so. On my laptop, I get the message: 'Problem with wireless adapter or access point', but the most confusing thing is that sometimes I can connect to the Internet via my network wireless without any problem.

  This time I decided to post my problem, because I'm tired of it. Sometimes it happens, sometimes it doesn't. Right now, I have two days without Internet connection (Via router), because my modem works properly.

  PS: I have another router (Linksys) and I can connect to this network, but I want to solve my problem with the TP-Link because the signal is stronger. Help!

  See links.

  How to install a TP-LINK wireless routers (Recommended)?

  http://www.TP-link.com/LK/article/?faqid=92

  Why can I not access the Internet after connecting the TP-LINK router to my modem.

  http://www.TP-link.com/LK/article/?faqid=138

  TP-Link FAQ.

  http://www.TP-link.com/LK/support/FAQ/?keywords=TL-WR841ND

• Power Save Polling (PSP) leads to problems in connection with some access points

  Symptoms:
  The following symptoms may be seen if an access point Wi - Fi (AP) or router Wi - Fi broadband does not properly support the Power Save Polling (PSP) feature:

  • Intermittent loss of Wi - Fi
  • Unable to open a connection Wi - Fi
  • Poor Wi - Fi connection data performance

  These symptoms may be more pronounced when on battery.

  Cause:
  The PSP mode is a feature that provides the long battery life for laptops. It requires coordination between the AP or router and the Wi - Fi adapter. Intel has discovered that some APs or routers may not implement the feature correctly or completely.

  Socorro

  Heard different things people try, depending on their wireless adapter.

  Start, control panel, device, netowrk, their adapter, power management Manager. Clear the checkbox to allow windows to turn off this device to save power

  Start, control panel, device, netowrk, their adapter, advanced management. Looking for antenna diversity. Some cards have it and others don't. Replace the Auto antenna by supply diversity

  Some have disabled Wireless N of their card and achieved good results.

  Some Wireless N adapters operate ONLY on the 2.4 GHz frequency.

  Using these parameters of the recommended wireless router I use channel 11, have GREAT results. I usually recommend creating a new SSID to make the connection easier. Wireless devices also needs to connect to the NEW network.

  Rick

• Setting up roaming with 1300ag access points

  Hello

  I have been give two 1300ag access point to set up

  I was asked to make sure that customers can place a PSA without disconnecting from the network (roaming is the right term?)

  I was told that I need to put the same SSID and different channels on two access points

  I doesn't seem to work.

  What else needs to be configured?

  Thanks for any help

  The APs owe me locayed so that... you should be able to detect the wireless signal between access points... should not be a coverage GAP between access points...

  Exam...

  > Scope of coverage should not be as below...

  AP1                                                              AP2

  <----------------------------------------------->                 <-------------------------------------------------------->

  <--------------->

  no overlap of signal

  > Scope of coverage should be like this...

  AP1

  <----------------------------------------------->AP2

  <-------------------------------------------------------->

  <---------->

  signal overlap

  This can be done by installing the AP on the roof and then around homelessness. or even not by any software survey site Cisco ACU or ADU.

  Concerning

  Surendra

• WCS does not see any access point, but see the 4400

  I have WCS, A 4400 and 1130ag access points. WCS see 4400s but none of the ap

  Hmmm... Is it APs running in stand-alone mode or lwapp? They must be using lwapp (lightweight) to be controlled by the regulator

• WAP54G Access Point in Client Mode

  A client mode Linksys Wireless-G Access Point can communicate with a wireless-n wrt300n router?

  I continue to see the next note that worries me, it won't work:
  NOTE: The WAP54G will communicate only with an another WAP54G when the value for the Client Access Point.

  If this is not the case, what can I use to connect my PC to the floor to my router to wide band wireless downstairs. I prefer to use something other than a wireless NETWORK card because the PC is in a bad spot in the House.

  Thank you.

  Thank you.

• Xbox Live with Mobile access point

  Someone had some luck using Xbox Live with the Mobile Hotspot app on Verizon's network? I was finally able to connect to Live using an open network, such as using WPA2 has never worked. However, it doesn't have any way for me to get a NAT open, so I can't play with most of my friends.

  And Yes, before you say anything, I know games by phone is not large. But it is faster than the satellite connection, I'm stuck with otherwise.

  Any help is appreciated.

  Hello and welcome to the forums;

  According to some google actually associated research to be able to connect to Live but not to join friends, looks like the Xbox 360 may need some specific ports forwarded. Unfortunately for now, the Mobile Hotspot app doesn't support port forwarding, and I suspect that's the reason of your difficulties.

  I would recommend which suggests adding this feature for our developers to www.palm.com/feedback .

  Life moves fast. Don't miss a thing.

  TreoAide

• HP 15-Ay007la: Wi - Fi does not detect wifi access points. HP AY007LA downgraded to Windows 7.

  Hi again once, I went down my laptop for windows 7. And one, I installed the drivers Wi - Fi, Web page of drivers and works, but when I reboot, the wifi no longer works, I tried to download, uninistalling, install again too many times and do not work. Map Wi - Fi are correctly installed and windows doesn't detect not all bad. But do not work, displays a red one does not detect a Wi - Fi connection. Map of the Internet: bcm43142

  Have you tried pressing the F12 key to enable the wireless?

  The one with the airplane on the key icon.

  It would be the only suggestion I can offer.

  If the bluetooth driver was not installed, try the previous version...

  This package contains the Broadcom Bluetooth driver and software for models supported that are running a supported operating system. Broadcom Bluetooth 4.0 driver is required to enable the Broadcom Bluetooth 4.0 devices and is compatible with Broadcom Bluetooth 3.0 and earlier versions.

  FTP://ftp.HP.com/pub/SoftPaq/sp71001-71500/sp71440.exe

• no icons on the desktop or the taskbar to normal startup, only starts with this access in safe mode. Currently, able to restart in safe mode to return to normal.

  tried everything, run mcafee, malware bytes, cc cleaner, mircosoft Mr fix it, cleaned up my Start menu.  recently downloaded from the apple software updates, this problem has produced about the same time, but not quite sure?  all the scans came back with nothing.  otherwise, pc works fine, very weird.

  Hello

  Follow the procedure described here clean boot to isolate the problem: http://support.microsoft.com/kb/929135

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• MAC filter with autonomous access points

  Hi all

  A very simple question... I want to create local wireless networks using autonomous APs for the first time. I know this can all do with a trivial way controller, but this project can't stretch to that...

  • Can I use MAC filtering on autonomous APs to restrict clients associate?
  • I think that it will be 1240AG devices, but I guess the answer is the same for all models?
  • Can I mix MAC filtering with WEP/WPA? And use MAC filtering without encryption?

  Thank you!

  Paul

  PS. I know filtering MAC is terribly weak, but it is a requirement here...

  Yes, you can:

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15filt.html#wp1034987

  Stupid requirements.

  Thank you

  Chris

• How can I cancel? This access point sucks

  I hate this, .i wanted to create my own stuff and it is impossible to fInure out, I come to cancel but could not find the option too

  Cancel see answer #1 in https://forums.adobe.com/thread/2023066 - includes a link to Chat from Monday to Friday