Internet connection with only a single cable to the ADSL PoRt ADSL in windows7

Similar Questions

• No internet connection with C6300 only cable modem/router - No. Ethernet cable plugged

  About once or twice a week I wake up my desktop PC and see an icon (bottom right) which indicates that I have no internet connection. When I run the troubleshooter network (right-click on the icon) it says to plug in my ethernet cable. I replaced the cable with another know good cable, but the problem continues to return (though intermittently). If I unplug the ethernet cable from the port of my C6300 Netgear and plug it back in the same or another port, the internet connection is restored. I'm on Windows 10 edition 64 - bit OS on my desktop tower PC (Dell). My internet provider is Cox Communications through their cable with up to 100 Mbps of speed. My Netgear firmware version is V1.02.20 to help you can provide me to solve this problem would be appreciated.

  Well, it has been a few weeks of performance without error since I replaced the Netgear C6300. So I close this investigation as "FIXED."

• PC cable loss of internet connection with router WRT160N V2

  I'm new to routers and I just added a router WRT160N (V2).  Wireless through my laptop is great. However, I have 1 PC connected physically to the router. The internet connection is sporadic on this PC. I have "wireless" internet service high speed and sometimes you click internet or check your emails, and there is no internet connection. It seems to be after the PC has been idle for a while. When you click on the internet icon PC on the router not even flashes her - it's like the PC and the router do not speak. If it does not connect, the connection is great. Any help would be appreciated!

  There is a known problem with intermittent connectivity and firmware to build 11 for the WRT160N V2. 11 is the current firmware on the Linksys site. Check if you have 11 build if your router is a V2.
  Downgraded to build 8 fits usually correct these deficiencies, but Linksys told several people that they do not have firmware version 8 to give end users.

  It's ONLY for the WRT160N V2 router. This firmware will not work on WRT160N V1.

  You can find it at http://audipages.com/router/

  Follow download them and instructions to downgrade firmware on this page.

• Internet connection with Windows XP, SP3 and Airport Extreme - the status is always "absorbing network address.

  My Airport Extreme connected my IMac immediately, but I am not able to connect on the side PC. Airport utility does not 'no matter what Airport wireless devices". When you check the status of the internet connection with PC tools, the correct network is indicated and shows an excellent signal strength. The status is: "absorbing the network address. However, nothing happens.

  Under 'Repair the wireless network connection', it shows, "Windows is taking the following steps: your IP address renewal" even once, nothing happens.

  Under hardware I show Atheros Wireless Network Adapter and the mention: "this device works correctly.

  Yet, no network connection. Any help will be greatly appreciated.

  Hello

  Keep the changes and open the wireless. For example, to disable security in the router (turn on when to managed to connect).

  You can also try the wireless in a friends house, or an Internet café to get a frame of reference for this behavior elsewhere.

  -------------------

  Wi - Fi in general.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled).

  If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• Windows vista-internet connection is only local. Worked fine until Vista has been reloaded.

  Internet connection is only local. Worked fine until Vista has been reloaded.

  Choose the manufacturer of your computer in the list and get them from there.

  Driver downloads:

  Acer:

  http://us.Acer.com/AC/en/us/content/drivers

  ADVENT:

  http://www.adventcomputers.co.UK/product-downloads

  Alienware:

  http://support.Alienware.com/Support_Pages/Restricted_Pages/driver_downloads.aspx

  ASUS:

  http://www.ASUS.com/support

  Dell:

  http://www.Dell.com/support/drivers/us/en/19/ProductSelector

  eMachines:

  http://www.eMachines.com/EC/en/us/content/drivers

  Fujitsu:

  http://www.Fujitsu.com/us/support/

  Gateway:

  http://us.gateway.com/GW/en/us/content/drivers-downloads

  HP:

  http://WWW8.HP.com/us/en/drivers.html

  Lenovo:

  http://support.Lenovo.com/en_US/downloads/default.page#

  LG:

  http://www.LG.com/us/support/software-manuals

  Samsung:

  http://www.Samsung.com/us/support/downloads

  Sony Vaio:

  http://eSupport.Sony.com/Perl/select-System.pl?Director=driver

  Toshiba:

  http://support.Toshiba.com/drivers

• My Windows Vista computer displays a black screen with only a white arrow to the mouse cursor.

  I have a black screen with only a white arrow to the mouse cursor.  I tried to start in safe mode, safe mode with networking, and safe mode in the command prompt. Each time, I just get a black screen with a white arrow cursor.  How can I get my screen back?

  original title: black screen

  Hello

  Remember to make changes to the computer before the show?

  Try the following methods and check the status of the issue.

  Method 1:

  Disconnect an external device connected to the computer with the exception of the keyboard and mouse and check if it helps.

  Method 2:

  If you have the Windows Vista disc, the computer by using the startup disk and perform the Startup Repair. See the following links:

  What are the system recovery options in Windows Vista?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  Make repairs to the system from the Windows recovery environment.

  http://Windows.Microsoft.com/en-us/Windows-Vista/make-system-repairs-from-the-Windows-recovery-environment-from-Windows-Vista-inside-out

  Method 3:

  If the method above does not solve the problem, then try to perform a restore of the system from the Windows Recovery Console. You can see the link provided in method 2.

• Connect with * address email is removed from the privacy * is blocked for one of the following reasons:

  Hi, Im Mohamed, I sigfn I http://www.hotmail.com whith my ID show this maseg

  Connect with * address email is removed from the privacy * is blocked for one of the following reasons:

  • Someone has entered the password wrong too many times.
  • If you registered for this ID through an organization, you may not be able to use the account again.

  How to unlock my mail,

  NOTE: I tried reset my password security Question, write the correct answer, then show

  This option is temporarily unavailable because incorrect information was entered too many times. Please, try another option or try again later.

  Help me pz

  PZ send the response to this ID * address email is removed from the privacy * OR * address email is removed from the privacy * very thanks.

  Hi M-GhiathDakkak,

  Your question about Hotmail he will be better answered in forum Windows Live Hotmail . Please repost your question here.

• Connect with * address email is removed from the privacy * is blocked

  There was a problem with the song in my account (* address email is removed from the privacy *) a week before. He has temporarily blocked because of some spam massages. but I had recovered the use of password reset code.
  Now, I had this massage
  Connect with * address email is removed from the privacy * is blocked

  • Someone has entered the password wrong too many times.
  • If you registered for this ID through an organization, you will not be able to use the account again

  I got the link for the reset several times and I have reset the password but whenever I try to sing in. I use to get the same massage. What can I do to recover my account. He is my school and counts deal with work. I need to return, please help me

  This forum is for posting comments on Microsoft Answers web site, not to any other technical questions.

  For me it looks like you're talking about a Windows Live ID.  Questions about who belongs in the center of Windows Live Windows Live ID Portalsolutions.

• I can't open my application. My internet connection is OK. So what's the problem?

  I can't open my application. My internet connection is OK. So what's the problem?

  I try to reload the application several times- but nothing helps? Then what should I do?

  

  Hi Hanna,

  I think that you have found the "download error" in the Apps Panel.

  Please check the help below document:

  Download error in the applications tab of Creative Cloud Desktop Application

  You can also view the threads below:

  https://forums.Adobe.com/thread/1832357

  Persistent Cloud error - error download - creative

  Re: Creative Cloud "Download error" message

  Kind regards

  Sheena

• Hi, I'm developing a simple mobile app in DW CC 2015 using JQuery Mobile. LIKE I need the list view with description of the product, functionality and image, I would like to connect with database instead of "writing" all the tables in the bearings inside

  Hi, I'm developing a simple mobile app in DW CC 2015 using JQuery Mobile. LIKE I need the list view with description of the product, functionality and image, I would like to connect with database instead of "writing" all the tables in the bearings inside the Jquery page. In the future I would also be able to add, to remove the DB records. Any help, tutorial... Thanks TG

  I would like to connect with the database instead of "writing" all the tables in the bearings inside the Jquery page

  This is usually done with a CMS (content management system). There are commercial products CMS like WordPress, Joomla and perch. You create one or several layouts and then create pages of these page layouts using the CMS. In this way, it is possible to have hundreds of pages, each with unique content, but a page layout that can be managed in a place of sharing.

  CMSs on shelf don't require programming skills. Otherwise, some of us write our own CMS with custom functions, but this requires back-end, as with PHP programming.

• Can not connect to the server. My internet connections has always been. What is the problem.

  I have never been able to use creative application of cloud, I have to reinstall every time go. The question is always, it says can not connect to the server. My internet connections has always been. What is the problem.

  
  

  Thank you

  Log, activation, or connection errors. CS5.5 and later, Acrobat DC

  https://helpx.Adobe.com/x-productkb/policy-pricing/activation-network-issues.html

• 13 elements requires an internet connection?  I just paid $70 in the hope of avoiding the need to use internet!

  13 elements requires an internet connection?  I just paid $70 in the hope of avoiding the need to use internet!

  I'm sorry - never mind.  I think I found my problem...

• my cable internet connection is only 10Mbps and won't go to 100 Mbps windows Vista premium edition

  My inter connection wire line or hard earth runs only at 10 Mbit/s and should be 100 Mbit/s running vista Home premium and and using realtek rtl8168C (P) / 8111C (P) FAMILY GIGABIT ETHERNET NIC (NDIS 6.0).  How can I solve this problem.

  Hello

  I'm not aware of any Internet service provider that offers a 100 Mbps connection.

  The speed of the Internet connection is not a function of your material, but by the contract you have with the provider.

• Problems of Internet connection with Windows CE 6.0

  original title: frustrated

  I have a netbook with windows ce 6.0 and I tried each troubleshooting method that could think about my internet provider which is clear. The problem is when I'm at work I can use wifi there without any problem, but at home I can't all internet so the end result is clear wireless telling me that they do not support windows this. I know I'm not the only one with windows this or the one trying to get on the internet.

  Hello

  ·          You use a router to connect to the internet?

  ·          If Yes, have you tried if internet connection work when it is connected through an Ethernet cable?

  Question suits you best in the MSDN forums.

  http://social.msdn.Microsoft.com/forums/en/category/EmbeddedWindows

  Diana

  Microsoft Answers Support Engineer

• Computer internet connection drop (only configuring a connection)

  Good evening.  I am running Win7.  I have a modem/router Netgear connected with BT broadband and Ethernet connection between my computer and the router.

  When I switch off my computer for the night and resume the next day, the computer says that I have no network connection.  My wife's cell phone and the son can always access the internet via the wireless connection, and in all other respects, the network is functional.

  In order to restore the internet connection from my computer after power off, I have to reset the router.  Once this is done, the computer takes up his internet connection and network with all its cable systems and wireless connections continue to work perfectly.  In my view, that it is a software problem with the adapter to computer network, but beyond my ability to resolve.  Grateful for any help you can give.

  Go to Device Manager and uninstall your network card.  Restart the computer and it will reinstall it.

  If that does not resolve the problem, I suspect that your router has a problem.  I notice that you tell us that your router wireless works well, but your (and only you) wired is not.

  You can also try to change the cable, but it rarely makes a difference.  Try also using a different router port.

  Replacement is not big an investment and typically brings benefits, if you buy well.  A high price on a new router doesn't mean better.  Some of the costs down those are just as good.  The Dlink DIR L 605 is an example of a great router at a reasonable price.