internet disconnection but to maintain the local network connections

Similar Questions

• ASA 5505 IPSEC VPN connected but cannot access the local network

  ASA: 8.2.5

  ASDM: 6.4.5

  LAN: 10.1.0.0/22

  Pool VPN: 172.16.10.0/24

  Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

  I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

  Here is my setup, wrong set up anything?

  ASA Version 8.2 (5)

  !

  hostname asatest

  domain XXX.com

  activate 8Fw1QFqthX2n4uD3 encrypted password

  g9NiG6oUPjkYrHNt encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.1.1.253 255.255.252.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP XXX.XXX.XXX.XXX 255.255.255.240

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS server-group DefaultDNS

  domain vff.com

  vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

  access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  logging trap warnings

  asdm of logging of information

  logging - the id of the device hostname

  host of logging inside the 10.1.1.230

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-server protocol nt AD

  AAA-server host 10.1.1.108 AD (inside)

  NT-auth-domain controller 10.1.1.108

  Enable http server

  http 10.1.0.0 255.255.252.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 10.1.0.0 255.255.252.0 inside

  SSH timeout 20

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntest strategy

  Group vpntest policy attributes

  value of 10.1.1.108 WINS server

  Server DNS 10.1.1.108 value

  Protocol-tunnel-VPN IPSec l2tp ipsec

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntest_splitTunnelAcl

  value by default-domain XXX.com

  disable the split-tunnel-all dns

  Dungeon-client-config backup servers

  the address value vpnpool pools

  admin WeiepwREwT66BhE9 encrypted privilege 15 password username

  username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

  the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

  tunnel-group vpntest type remote access

  tunnel-group vpntest General attributes

  address vpnpool pool

  authentication-server-group AD

  authentication-server-group (inside) AD

  Group Policy - by default-vpntest

  band-Kingdom

  vpntest group tunnel ipsec-attributes

  pre-shared-key BEKey123456

  NOCHECK Peer-id-validate

  !

  !

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege show import at the level 5 exec mode command

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege, level 3 see fashion exec command eigrp

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege see the level 3 exec command mode dynamic filters

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  privilege clear level 3 exec command mode dynamic filters

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

  : end

  Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

  The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

  On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.

• Time Machine backs up only on the local network connection

  Hello

  I have a LAN Ethernet and a wireless connection to the same network. Is it possible to force the backup Machien time to use only the ethernet LAN connection in all cases? I want to warn the TMB to limit the bandwidth of my wireless network.

  Ethernet to be the highest network interface ordered to force, and as long as you're connected Ethernet, it be the interface for all traffic.

  System-> network preferences

  

  If you want seamless switching between WiFi and Ethernet, then your router book the same IP address for the interface Ethernet and WiFi connections.  This is done differently by the router of different brands and models.  For an Airport Extreme/Time Capsule, it would be done by giving your Ethernet and TCP/IP WiFi of the same name from DHCP reservations settings, and then associate the DHCP reservation name with an IP address in Airport Extreme network settings.

• How to isolate 1 of 2 PC connected to the local network connected to an Internet EXTENDED?

  I have 2 XP PC and a new HP printer; all are connected by wire to a Linksys router who is connected to a modem, DSL - Internet AT@T so both computers can use the printer. How do I isolate one of the PC from the Internet?

  If you do this, you may want to assign a static IP address to the computer you want to isolate from the wan.  Ohterwise the IP address will change periodically

  http://PortForward.com/Networking/static-XP.htm

• the resulting network - failed to add the local network connection

  Dear all,

  the network problem - not getting the images mounted VM LAN and it allocates any intellectual property, to be neither we are able to assign.

  Please find screen captures below

  

  We have tried to add maps with flexible network, E1000 etc. but, no gain...

  

  Details of the env

  

  Appreciate the help and advice to proceed

  Thanks and greetings

  JO

  I'm a little confused on the material that is shown in the screenshot. It is a newly installed virtual machine or do you convert it? If so do you convert using the converter version 4.1 indicated in your first post or version 5.0 converter that supports Windows 7/2008?

  André

• Customer Cisco PIX 501 VPN connects but no connection to the local network

  Hi all:

  I am able to make a VPN connection to a PIX 501. The remote client is assigned an IP (192.168.2.1) also, but not able to access all the machines in the local network connected to the PIX.

  I have attached the PIX configuration.

  Advice will be greatly appreciated.

  ********************

  6.3 (5) PIX version

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxxx

  pixfirewall hostname

  domain ciscopix.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  access-list 102 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool ippool 192.168.2.1 - 192.168.2.5

  location of PDM 192.168.2.0 255.255.255.0 outside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) - 0 102 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup vpn3000 ippool address pool

  vpngroup vpn3000 Server dns 68.87.72.130

  vpngroup vpn3000-wins 192.168.1.100 Server

  vpngroup vpn3000 split tunnel 101

  vpngroup vpn3000 downtime 1800

  password vpngroup vpn3000 *.

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:xxxx

  ****************

  The DNS server is the one assigned to me by my ISP.

  My internal network connected to the PIX is 192.168.1.1 - 192.168.1.33 and the VPN ip pool is 192.168.2.1 - 192.168.2.5

  "isakmp nat-traversal 20" can do the trick.

• 3 local network connection and local network connection

  I have a Dell with Netgear router wireless. On my computer, I have two connections to the LAN. 3 local network connection and local area connection. When I activate 3 internet works on the computer, but the wifi does not work. When I activate the connection to the internet LAN doesn't work at all. someone know how to fix the wifi?

  What else shows in network connections (start > run > ncpa.cpl > OK)?  Please list all icons.

  On the Local network connection, right click and select Properties.  Which shows in the 'Général' tab in the box under "connect using"?

  On Local Area Connection 3, right-click and select Properties.  Which shows in the 'Général' tab in the box under "connect using"?

  • With both items enabled, open a command prompt window (start > run > cmd > OK).
  • Type the following command in the black command prompt window and press ENTER after each line

  ipconfig/all > "% userprofile%\Desktop\ipinfo.txt".
  Notepad '% userprofile%\Desktop\ipinfo.txt '.

  • Copy the contents of the Notepad window and paste it into your reply here
  • Close Notepad and windows command prompt and remove the file ipinfo.txt to your desktop

• How can I disconnect from the internet but to maintain my connection to the local network in Windows 7?

  I need to disconnect internet to my PC Windows 7 while maintaining my LAN network. Can anyone help?

  Hello

  If you want to disconnect Internet on the Windows 7 computer, then you can follow the steps mentioned below. These steps would help you to disconnect from the wired connection, while the connection is still active.

  (a) click Start.

  (b) type network and sharing Center in the start search bar and press ENTER.

  (c) in the left pane, click on change adapter settings

  (d) it would be to open a window with the connection to the wired LAN.

  (e) now, right click on the wired LAN connection icon and select Disable. (Provide the password if necessary).

  (f) it would disconnect the computer from Windows 7 to connect to the local network.

• Connected to the local network, but can not use internet

  I recently had problems with access to the internet after reinstalling windows 7. Before the reinstall worked very well.

  I can connect to the local network without problem, and it shows that the internet is connected. Yet I can not access the internet. When I disconnect and reconnect, I get a few seconds of internet work before it stops working.

  When a diagnosis in the network and sharing Center, I get the error "default gateway is not available" and occasionally "the connection between your access point, etc. and internet is broken"

  Other computers and devices using the network are working properly, although there was a 'competitor IP address' error on another pc, which, after a reconnection, solved itself.

  I use an edimax 802.11n wireless card and a D-link router

  I tried several things to make it work again, but without result. Any help would be greatly appreciated

  disable TCP/IPv6 had no effect.

  I think I can have fixed me, I installed the driver microsoft before the reinstall instead of the driver edimax and internet suddenly started working.

  Thanks for the help of yor

• I can connect to the local network, but not to the internet

  Why in an internet connection, I can connect to the Local network, but not to the Internet.
  I have valid IP address and configuration is good.

  I recommend you read some threads here in the forum about similar issues.
  If this problem occurs using the WiFi network, then check if you can use the connection to the local network.
  Using the WiFi network, you must check if the common WLan parameters are favourable;
  Check if the encryption key is right; turn off filtering by mac address, check the TCP/IP protocol settings if it has been set to automatic, disable the firewall settings, rest you WLan router, check if you connected to the right SSID.

  Good bye

• In the Internet properties and connections and the local network settings, I uncheck the box for a proxy server, but in a few moments, the computer checks the box

  In the Internet properties and connections and the local network settings, I uncheck the box for a proxy server (because it is blocking my access to Internet Explorer), but within moments, the computer checks the box. What can I do to stop the area of the check proxy server box?

  original title: LAN settings

  Have you checked for viruses?

  http://www.eset.com/us/online-scanner/

  It is very common that the virus to do.

• I lose the internet connection randomly but never lose my wireless network connection.

  I use a hp pavilion dv9500 with 64-bit vista sp2 and built in a wireless adapter that will fall randomly my internet wireless connection, but maintains my wireless network connection with an excellent signal strength.

  My (non-permanent) fixed
  I know how to reconnect to the internet, but it forces me to diagnose a repair my connection. It then displays "cannot connect to Server primary dns (75.75.75.75)"after which it gives "things to try" who never work and a button 'Reset the ip address' that I click. " repair bar will fill up to half way and go to a new screen solution that shows more 'solutions' and a "reset wireless adapter" button which I click. the remedy bar will fill and then display windows can not solve the problem and go for help. I then manually disconnect from the wireless network and my computer will automatically reconnect to the network and to the internet. It takes about five minutes to fix, but it happens so often that it is getting boring. The process will not work if I only to reset the ip address and then disconnect from the network, only to reset the wireless adapter and then disconnect, or just disconnect from the network and reconnect. I have to reset the ip address and the wireless adapter and then disconnect from the network.

  The internet connection will tend to disconnect when I watch a lot of youtube videos, when I download large files like a game on steam, or just just randomly when I use it. I'll use it for a long time and he can't let it go, but sometimes it will go down to ten minutes after I had just reconnected in a drop-down list. It happens randomly without another warning that download time will increase from 2 mb to 50 k in two seconds all about or stop the loading of a youtube video when I look at it.

  I searched everywhere for an answer, but it's as if it were a new problem for all humanity or just im the only person who does not know how to solve this problem, because there are no forums or FAQ not related to my problem. It is not so much a serious problem such as an irritating problem that appears at inconvenient times or when I just want to relax and watch a video. It takes some time to reconnect and even though I know how it would be better if my connection would just stay connected to the internet at any time.

  I have no idea what the problem could be that whenever I have find I never get related problems. all advice or solution would be great.

  I also share this modem with other three commonly used computers: a wired office and two other laptops that the two are connected wirelessly. both other laptops do not have the same problem as mine. My router is a linksys e3000 wireless router.

  Hi DustinMoor3,

  Follow the troubleshooting steps posted by Shekhar (marked as the answer) in this thread to solve the problem with no connection to the primary DNS server, in particular the method 2 worked for other users.

  * These steps should also work for Vista *.

• Impossible to connect to the wireless network when the wireless Internet is filled to connect to the Local network

  I tried to fill the connection between my laptop Wi - Fi and an ethernet cable LAN via the connection to the Local network for my xbox 360. However, when the connections passed the wireless connection would show that it is disconnected and would not reconnect. When I tried to repeat the process sometimes the same thing happens sometimes it says that it is still connected.

  However, be that as it may, both times I could not load any page of the website from my laptop and xbox connect any.
  How can I create a network bridge and get the wireless internet to connect please?

  Any help to fix this would be appreciated,
  P

  This Microsoft Knowledge Base article might help: bridge may not work with a Non-Promiscuous Mode network card .

  If not, I recommend to delete the network bridge and enable sharing of Internet connection on the wireless network connection. Boulder computer Maven
  Most Microsoft Valuable Professional

• No Internet access, the 'Connect to the Local network' and 'Wireless network connection' are "Local only".

  I'm portable computer maintenance of the customer, a Toshiba Satellite L305-S5885, under Vista Home Premium x 86 SP2, with infections by malicious software and internet connection problems. I have managed to get rid of all of its 251 infections and I am now addressing the connectivity problem. I'm unable to achieve on its ethernet or a wireless connection to Internet. The two network status of connections 'Unidentified network', and also ' access: Local only ' all other machines hooked up to my router via CAT5e and some via 802.11 g/n, have excellent speeds with internet connectivity, so I know that the problem is limited to his machine. I tried the following:

  Deactivation and reactivation of these two connections: FAIL.

  "Diagnose and repair" on the two connections: FAIL.

  Under dynamic I.P. type to static/static to the dynamic: FAIL.

  Uninstalled all network via Device Manager devices, then restart: FAIL.

  Manually uninstalled all the drivers and utility and installed the latest versions: FAIL

  The command ipconfig/all text follows:

  ----------------------------------------------
  Microsoft Windows [Version 6.0.6002]
  Copyright (c) 2006 Microsoft Corporation. All rights reserved.

  C:\Users\Brooklyn's>ipconfig/all

  Windows IP configuration

  Name of the host...: Brooklyns-PC
  Primary Dns suffix...:
  Node... type: broadcast
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Intel (r) Wireless WiFi Link 4965AGN
  Physical address.... : 00-21-5C-31-87-95
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.174.235 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  Description...: Realtek RTL8102E Family PCI - E Fast Ethern
  and NIC (NDIS 6.0)
  Physical address.... : 00-1E-33-4E-2E-F7
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.74.29 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {C41651CC-0B3D-411D-8187-745214 C 69}
  B4B}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {816357D 3-D 8-494C-AA09-F622AE861 44}
  0FA}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  C:\Users\Brooklyn's >
  --------------------------------------------------

  Guys, I'm really hitting my head against the wall on this one, and I would be VERY happy for any help through this. Thank you!

  I thought about it, there was a corrupted installation of Norton 360, the origin of the problem. I've used the Norton removal tool and voila! Internet! Thank you.

• Laptop wireless with NETGEAR router Home Windows Vista detects on the local network and internet

  We have a laptop Toshiba Satellite L505-S6946 with Windows Vista on it. We bought a router Netgear Wireless G WGR614V10 a few months ago and installed ok. It worked fine for a few months. Now the network connection to the bottom rhs shows tray icon: 'Local only' for the connection of the SSID, we have implemented. Technical support Netgear has determined that the router works fine. But they noted that the router might get a static IP address in his settings of the adapter wireless Vista. And they said that something should be changed in Vista to a direct connection with the modem works fine for internet access, but it's bulky. Someone please do you suggest to fix this error? Thank you!!!

  Hello

  A message in the small window that says connected wireless does not mean that you really have a valid functional connection.

  Linking the means of router you can enter the IP base of the router in an address bar in one go, being able to connect, see and configure the router menus (extended to the wireless router manual should explain how to do).

  If it will not connect to your wireless router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  ----------------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Firewall software can block traffic Local to the network that you are trying to use because it is not set to the network Zone Trust.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP (network IP number) of work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET