Invalid header, lack of payload SA!

Community salvation.

I'm creating a L2L VPN between Cisco ASA and Cyberhome and get the error message on ASA below and my tunnel is not started:

07 June-07:08:36 [IKEv1] IP = XXX.XXX.XXX.XXX invalid header, lack of payload SA! (next payload = 4)

07 June 07:08:55 [IKEv1] IP = XXX.XXX.XXX.XXX invalid header, lack of payload SA! (next payload = 4)

07 June-07:09:36 [IKEv1] Group = XXX.XXX.XXX.XXX, IP = XXX.XXX.XXX.XXX, impossible to find a group valid tunnel, abandonment...!

07 June 07:09:46 [IKEv1] IP = XXX.XXX.XXX.XXX invalid header, lack of payload SA! (next payload = 4)

07 June at 07:10:06 [IKEv1] IP = XXX.XXX.XXX.XXX invalid header, lack of payload SA! (next payload = 4)

07 June 07:10:47 [IKEv1] Group = XXX.XXX.XXX.XXX, IP = XXX.XXX.XXX.XXX, impossible to find a group valid tunnel, abandonment...!

What can be the reason for this?

Kind regards.

Hello

Please check the configuration of tunnel of the relevant peer group.

It seems that the IP address of the Cyberhome is incorrect on the ASA or we do not have any group configured tunnel.

Please check name of tunnel group and key shared before.

Kind regards

Aditya

Please evaluate the useful messages and mark the correct answers.

Tags: Cisco Security

Similar Questions

  • Cannot install the program, the error message: Server error 145905 [invalid header] communications failure

    Original title: communication failure 145905 [invalid header]

    When you try to install a program I always get this error each time message: Server error 145905 communication failure [invalid header] would appreciate any help that anyone can provide. Thank you.

    Hello

    That is the application that you are trying to install?

    I suggest you follow these methods and check.

    Method 1: Run the hotfix to correct the following problems with programs that cannot be installed or uninstalled

    http://support.Microsoft.com/mats/Program_Install_and_Uninstall/

    Method 2: Perform the clean boot, try to install application.

    Follow the suggestions of this link.

    http://support.Microsoft.com/kb/310353

    NOTE: Once you check the functionality, follow the suggestions under steps to configure Windows to use a Normal startup state.

    If the problem is specific to the program, I suggest you please contact the manufacturer of the program for utilities.
     

    I hope this helps!

  • ERROR: Not supported format the disk (VMDK sparse invalid header)

    Hi all

    I just met ovftool and gave it a try. I am fairly new to the world of VMware.

    I have a. OVF I exported customer using vSphere 4.0. It. OVF consists of 3 Suse Linux based virtual machines. that is, I created a vApp on host ESX (4.1) in this TIME, I put my 3 VMs of SLES and then exported in file OVF.

    It has a total area of about 4.5 GB.

    Now, I ran this command to compress it. OVF and gave the opportunity to create a deltadisks.

    C:\ > ovftool - compress = 9 - makeDeltaDisks - skipManifestCheck MyVMCluster\MyVMCluster.ovf E:\

    output:

    {{{

    The manifesto does not validate
    Generate records of delta for 2 discs (40960 MB capacity)
    Playing discs
    Transfer complete disc

    Determine the optimal configuration for the Group of capabilities
    Configuration of disk write
    Transfer complete disc

    Completed successfully

    }}}

    Now, when I checked my E:\ He had created a folder with the same name and place the associated files. I saw a significant reduction in the new vmdk format. (about 2.3 GB now)

    So, when I deploy this new ovf vSphere client manually, it will up to certain age % and then reports an error:

    {{{

    Error loading file to the server (E:\MyVMCluster\disk3.vmdk.gz) not a supported (header invalid sparse vmdk) disc format

    }}}

    and then it stops and all rolledback.

    Pointers?

    Thank you

    Madalena

    use the data - store = datastore2 (no space)

    Eske

  • L2TP - impossible to find a group valid tunnel

    Hello

    I'm sure this is a simple solution, but I don't see what I'm missing.

    Any help please?

    Get the following errors in debugging.

    [IKEv1]: invalid tunnel, leaving group = 95.83.254.91, IP = 95.x.x.x, impossible to find a group...!
    23 September 14:26:05 [IKEv1]: IP = 95.x.x.x, invalid header, lack of payload SA! (next payload = 4)

    Group of tunnel I want to use is Remote-L2TP

    Attached config.

    ASA Version 8.2 (5)
    !
    ciscoasa hostname
    domain xxxxx.local
    activate 8Ry2YjIyt7RRXU24 encrypted password
    2KFQnbNIdI.2KYOU encrypted passwd
    names of
    name 192.168.1.40 description CCTV system CCTV_System
    name x.x.x.x outside outside interface description
    description of the SERVER name server 192.168.1.1
    !
    interface Ethernet0/0
    switchport access vlan 2
    !
    interface Ethernet0/1
    switchport access vlan 12
    !
    interface Ethernet0/2
    !
    interface Ethernet0/3
    !
    interface Ethernet0/4
    !
    interface Ethernet0/5
    !
    interface Ethernet0/6
    !
    interface Ethernet0/7
    !
    interface Vlan1
    nameif inside
    security-level 100
    192.168.1.222 IP address 255.255.255.0
    !
    interface Vlan2
    nameif outside
    security-level 0
    IP address outside 255.255.255.252
    !
    passive FTP mode
    clock timezone GMT/IST 0
    summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00
    DNS domain-lookup outside
    DNS server-group DefaultDNS
    Server name 89.191.34.249
    domain xxxxx.local
    object-group service CCTV tcp
    port-object eq 9010
    object-group service CCTV_NEW tcp - udp
    port-object eq 9091
    object-group service BlackBerry tcp - udp
    port-object eq 3101
    object-group service NSM tcp - udp
    port-object eq 886
    object-group service RDP tcp - udp
    EQ port 3389 object
    object-group Protocol TCPUDP
    object-protocol udp
    object-tcp protocol
    outside_access_in list extended access allowed object-group TCPUDP any host outside eq 9091
    outside_access_in list extended access allowed object-group TCPUDP any host outside eq 886
    outside_access_in list extended access allowed object-group TCPUDP any host outside eq 3101
    outside_access_in list extended access permit tcp any host outside eq https
    outside_access_in list extended access permit tcp any interface outside eq pptp
    outside_access_in list extended access allowed esp any external interface
    outside_access_in list extended access permit udp any interface outside isakmp eq
    outside_access_in list extended access permit udp any interface outside eq 4500
    outside_access_in list extended access permit udp any interface outside eq 1701
    standard access list for distance-VPN-Gp_splitTunnelAcl permit 192.168.1.0 255.255.255.0
    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.25.0 255.255.255.192
    RemoteVPN_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
    VPN-GP_splitTunnelAcl-list of allowed access standard 192.168.1.0 255.255.255.0
    standard L2TP_splitTunnelAcl-Remote Access-list allowed 192.168.1.0 255.255.255.0
    pager lines 24
    Enable logging
    asdm of logging of information
    Within 1500 MTU
    Outside 1500 MTU
    mask of local pool Remote-DHCP-POOL 192.168.25.10 - 192.168.25.50 IP 255.255.255.0
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    don't allow no asdm history
    ARP timeout 14400
    Global 1 interface (outside)
    NAT (inside) 0-list of access inside_nat0_outbound
    NAT (inside) 1 0.0.0.0 0.0.0.0
    public static 9091 9091 CCTV_System netmask 255.255.255.255 interface tcp (indoor, outdoor)
    public static 886 886 SERVER netmask 255.255.255.255 interface tcp (indoor, outdoor)
    public static 3101 3101 SERVER netmask 255.255.255.255 interface tcp (indoor, outdoor)
    public static tcp (indoor, outdoor) interface https SERVER https netmask 255.255.255.255
    public static tcp (indoor, outdoor) pptp pptp netmask 255.255.255.255 SERVER interface
    Access-group outside_access_in in interface outside
    Route outside 0.0.0.0 0.0.0.0 89.191.53.17 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    Floating conn timeout 0:00:00
    dynamic-access-policy-registration DfltAccessPolicy
    the ssh LOCAL console AAA authentication
    AAA authentication http LOCAL console
    Enable http server
    http 192.168.1.0 255.255.255.0 inside
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    Crypto ipsec transform-set esp-3des esp-sha-hmac trans
    Crypto ipsec transform-set trans transport mode
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    Crypto-map Dynamics dyno 20 transform-set trans
    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    card crypto 20-isakmp ipsec vpn Dynamics dyno
    vpn outside crypto map interface
    Crypto ca trustpoint _SmartCallHome_ServerCA
    Configure CRL
    Crypto ca trustpoint ASDM_TrustPoint0
    registration auto
    name of the object CN = ciscoasa
    Configure CRL
    Crypto ca certificate chain _SmartCallHome_ServerCA
    certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
    308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
    010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
    30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
    13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
    0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
    20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
    65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
    65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
    30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
    30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
    496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
    74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
    68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
    302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
    63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
    010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
    a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
    9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
    7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
    15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
    1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
    18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
    4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
    81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
    082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
    7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
    ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
    45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
    2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
    1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
    03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
    69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
    02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
    6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
    c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
    69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
    1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
    445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
    1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
    2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
    4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
    b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
    99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
    481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
    b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
    5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
    6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
    6c2527b9 deb78458 c61f381e a4c4cb66
    quit smoking
    string encryption ca ASDM_TrustPoint0 certificates
    certificate 5eb57b56
    3082016a 30820201 a0030201 0202045e b57b5630 0d06092a 864886f7 0d 010105
    3111300f 05003045 06035504 03130863 6973636f 61736131 30302e06 092 has 8648
    09021621 63697363 6f617361 2e627574 6 c 657274 6563686e 6f6c6f67 86f70d01
    6965732e 6c6f6361 6c301e17 313630 39313931 33303732 395a170d 32363039 0d
    a 31373133 30373239 5 304531 11300f06 03550403 13086369 73636f61 73613130
    2a 864886 f70d0109 6973636f 02162163 6173612e 6275746c 65727465 302e0609
    63686e6f 6c6f6769 65732e6c 6f63616c 30819f30 0d06092a 864886f7 0d 010101
    8 D 003081 89028181 05000381 008e76a6 2ad8e079 15814471 df2c3309 abdc0ae7
    1c665f5f bb09154b 1ac3fd81 930b29cb 6da29338 738c 9373 a0b30f61 a1d08aa9
    f5ef926b 11ef1e22 e8beeb5f c6606090 7a71b367 cad571c5 56331678 d83d4bb4
    9f98a565 577cccd6 dc20e190 c7128cf2 e38d3ad1 37807440 3da501c2 14bbbe02
    45abf677 89248633 d 05589d 4886f70d 01010505 55 75020301 0001300 06092a 86
    000a7b9d 00038181 3e29b1d9 8459309b 5e24606a cae0710e b9e264f4 a61125b9
    2f431f3a 5c4a9485 fe9bc0b0 9f9f7072 13abd978 243e0542 e34642d6 ae33028d
    be03b9e9 56c693ab b082932d b44ab014 9366c0d4 529a7ff5 818f7293 2026521b
    52fcf5c7 d623f7fa 54019c 86 e64a4212 08444c 58 8ccd11d8 4297d18a c4b2de33
    2003eaf5 e2
    quit smoking
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH 192.168.1.0 255.255.255.0 inside
    SSH 0.0.0.0 0.0.0.0 outdoors
    SSH timeout 30
    SSH version 2
    Console timeout 0
    dhcpd outside auto_config
    !

    a basic threat threat detection
    Statistics-list of access threat detection
    a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
    NTP 79.125.112.210 Server
    NTP server 193.1.193.157 prefer external source
    WebVPN
    port 8443
    allow outside
    DTLS port 8443
    SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
    SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2 image
    Picture disk0:/sslclient-win-1.1.4.176.pkg 3 SVC
    enable SVC
    attributes of Group Policy DfltGrpPolicy
    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
    WebVPN
    SVC request enable
    internal RemoteVPN group strategy
    attributes of Group Policy RemoteVPN
    value of server DNS 192.168.1.1 192.168.1.2
    Protocol-tunnel-VPN IPSec
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list RemoteVPN_splitTunnelAcl
    XXXX.local value by default-field
    internal strategy group at distance-VPN-GP
    remote control-VPN-GP group policy attributes
    value of 192.168.1.1 DNS server
    Protocol-tunnel-VPN IPSec
    XXXXX.local value by default-field
    internal strategy group to distance-L2TP
    L2TP remote group policy attributes
    value of server DNS 192.168.1.1 192.168.1.2
    VPN-tunnel-Protocol webvpn
    username privilege 15 encrypted v5FJjvsPy8PsIOtZ xxxxpassword
    attributes of username xxxx
    VPN-group-policy RemoteVPN
    xxxxx YeC9t79Bj2E5FxxV username encrypted password
    attributes of username xxxxx
    Strategy-Group-VPN Remote - L2TP
    2KXeP2Ggcoa6BTsozucgAA password xxxxx user name is nt encrypted
    remote access of type tunnel-group to distance-VPN-GP
    distance-VPN-GP-global attributes tunnel-group
    Remote control-DHCP-POOL-pool of addresses
    Group Policy - by default-remote control-VPN-GP
    tunnel-group GP-remote control-VPN ipsec-attributes
    pre-shared key *.
    type tunnel-group Remote-L2TP remote access
    attributes global-tunnel-group Remote-L2TP
    Remote control-DHCP-POOL-pool of addresses
    Group Policy - by default-remote-L2TP
    tunnel-group Remote-L2TP ipsec-attributes
    pre-shared key *.
    tunnel-group Remote-L2TP ppp-attributes
    ms-chap-v2 authentication
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    inspect the pptp
    !
    global service-policy global_policy
    context of prompt hostname
    anonymous reporting remote call
    Cryptochecksum:c4b7c39420a91e2f7bb4adc5e5a8539b
    : end
    ciscoasa (config) #.

    Hello

    I see same Phase 2 is completed in the newspapers, so more than a customer issue.

    On the Security tab in the connection on the client profile, check if you have allowed the correct password and security protocols:

    https://www.SoftEther.org/4-docs/2-HOWTO/9.L2TPIPsec_Setup_Guide_for_Sof...

    Kind regards

    Aditya

    Please evaluate the useful messages and mark the correct answers.

  • Questions from VPNTunnel Watchguard & ASA

    I am creating a Site at the tunnel site of Cisco ASA 5510 to Watch 500th guard & iam getting the error in the logs on the SAA below

    Invalid header, lack of payload SA! (next payload = 4)

    Tunnel, abandonment... valid IP = x.x.x.x, impossible to find a group!

    Group = x.x.x.x, IP = x.x.x.x, drop table homologous counterpart has no, no match!

    pls help

    Create a new group and isakmp identity address.

  • Question of L2TP with ASA

    HI.i want to connect from xp client PIX via L2TP IPsec connection, but I cant.this is my network.

    PIX:

    outside = 15.15.15.1/24

    inside = 10.10.10.1/24

    XP = 15.15.15.2 (connected to the AAS outside interface) client

    PIX config:

    !!!!!!!!

    PIX Version 7.2 (3)

    !

    pixfirewall hostname

    activate the password xxx

    names of

    !

    interface Ethernet0

    nameif outside

    security-level 0

    IP address 15.x.x.1 255.255.255.0

    !

    interface Ethernet1

    nameif inside

    security-level 100

    IP 10.10.10.1 255.255.255.0

    !

    interface Ethernet2

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Ethernet3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Ethernet4

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    passwd xxx

    passive FTP mode

    TR1 extended access list ip 10.10.10.0 allow 255.255.255.0 17.17.17.0 255.255.

    55.0

    TR2 extended access list ip 10.10.10.0 allow 255.255.255.0 17.17.17.0 255.255.

    55.0

    list of access allowed extended l2tp udp any any eq 1701

    pager lines 24

    Outside 1500 MTU

    Within 1500 MTU

    17.17.17.2 - 17.17.17.10 vpn IP local pool

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    NAT (inside) 0-list of access tr1

    group-access l2tp in external interface

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout, uauth 0:05:00 absolute

    Enable http server

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-3des esp-md5-hmac ipsec

    Crypto ipsec dy 1 transform-set dynamic-map

    crypto card cry 1-isakmp ipsec dynamic dy

    out cry crypto map interface

    crypto isakmp identity address

    crypto ISAKMP allow outside

    crypto ISAKMP policy 1

    preshared authentication

    3des encryption

    md5 hash

    Group 2

    life 86400

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    !

    !

    Sevan strategy of Group internal

    attributes of sevan group policy

    Protocol-tunnel-VPN l2tp ipsec

    Sevan username password xxx

    sevan username attributes

    Protocol-tunnel-VPN l2tp ipsec

    sevan tunnel-group type ipsec-ra

    tunnel-group sevan General attributes

    vpn address pool

    Group Policy - by default-sevan

    Sevan tunnel ipsec-attributes group

    pre-shared-key *.

    Sevan tunnel-group ppp-attributes

    No chap authentication

    ms-chap-v2 authentication

    context of prompt hostname

    Cryptochecksum:xxx

    : end

    in the client Xp I configured the vpn connection correctly according to the examples I found in the Cisco documents.

    When I try to connect from xp client nothing happens I turn on debugging and I get this error:

    Oct 07 12:04:51 [IKEv1]: group = 15.15.15.2, IP = 15.15.15.2, cannot

    find a group valid tunnel, abandonment...!

    Oct 07 12:04:51 [IKEv1]: = 15.15.15.2, IP = 15.15.15.2, peer group of withdrawal of

    table peer has failed, no match!

    Oct 07 12:04:51 [IKEv1]: group = 15.15.15.2, IP = 15.15.15.2, error: unable to r

    eMove PeerTblEntry

    Oct 07 12:04:52 [IKEv1]: IP = 15.15.15.2, invalid header, lack of payload SA! (n

    support useful ext = 4)

    Oct 07 12:04:54 [IKEv1]: IP = 15.15.15.2, invalid header, lack of payload SA! (n

    support useful ext = 4)

    Oct 07 12:04:58 [IKEv1]: IP = 15.15.15.2, invalid header, lack of payload SA! (n

    support useful ext = 4)

    Oct 07 12:05:06 [IKEv1]: IP = 15.15.15.2, invalid header, lack of payload SA! (n

    support useful ext = 4)

    Please help me find the problem! Thank you

    I recommend something similar. But instead to "no protocol-tunnel-vpn l2tp-ipsec", you can also place the order

    "vpn-tunnel-Protocol l2tp ipsec" in the DefaultRAGroup tunnel-group concerned both group policy. Just make sure you don't violate one of your other VPN. See this for more details:

    http://www.securityie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=10;t=001767

    Concerning

    Farrukh

  • L2l with certificates between 2 ASAs

    Hi all

    I want to set up a VPN L2L/Site-to-site tunnel, which authenticates by using certificates.

    In fact I am following this guide-> http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080aa5be1.shtml

    I configured the tunnel group on both ends, with the trustpoint configured, authenticated and accepted specified.

    I correspondent isakmp policies at both ends, and of course my cryptographic cards contains 3 identical lines - set peer match access-list and transformation-a set cryptomap. Next to those, there are 2 identical lines for life. I haven't specified the trustpoint in encryption card while it is not indicated in the top link (guide) to do, even if I tried, without different result. Debugs him happens exactly the same each time:

    Debug the cry isa 10: (on the remote end)

    TEST-ASA-RA # debug cry isa 10

    TEST-ASA-RA # Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + SA (1) the SELLER (13) + the SELLER (13) + the SELLER (13), SELLER (13) + (0) NONE total length: 208

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, SA payload processing

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Oakley proposal is acceptable

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received NAT-Traversal worm 02 VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, worm received 03 NAT-Traversal, VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received NAT - Traversal RFC VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received Fragmentation VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: true

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE SA payload processing

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build the payloads of ISAKMP security

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, construction of Fragmentation VID + load useful functionality

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + HER (1), SELLER (13) + (0) NONE total length: 108

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + KE (4) NUNCIO (10) + CERT_REQ (7) + CERT_REQ (7) seller (13) + the seller (13) + the seller (13) + the seller (13) + (0) NONE total length: 374

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, processing ke payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing ISA_KE

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, nonce payload processing

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment certificate request payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment certificate request payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, the customer has received Cisco Unity VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received xauth V6 VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment VPN3000 / ASA payload IOS Vendor ID theft (version: 1.0.0 capabilities: 20000001)

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received Altiga/Cisco VPN3000/Cisco ASA GW VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building ke payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building nonce payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building certreq payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build payloads of Cisco Unity VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, constructing payload V6 VID xauth

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Send IOS VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, ASA usurpation IOS Vendor ID payload construction (version: 1.0.0 capabilities: 20000001)

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build payloads VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Send Altiga/Cisco VPN3000/Cisco ASA GW VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Generating keys for answering machine...

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + KE (4) NUNCIO (10) + CERT_REQ (7) seller (13) + the seller (13) + the seller (13) + the seller (13) + (0) NONE total length: 298

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, RRs would fragment a new set of fragmentation. Removal of fragments of old.

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, assembled with success an encrypted pkt of RRs would be fragments!

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + ID (5) + GIS (9) + IOS KEEPALIVE (128) + CERT (6), SELLER (13) + (0) NONE total length: 1987

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing ID

    Jul 07 11:36:18 [IKEv1 DECODER]: IP = 80.62.240.136, ID_IPV4_ADDR received ID

    80.62.240.136

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing cert

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment of RSA signature

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, calculation of hash for ISAKMP

    Jul 07 11:36:18 [IKEv1 DECODER]: Dump of Signature received, len 256:

    0000: 8D97FE83 CDA9CEB2 A5D7F63F 0FAA76A4...? ... c.

    0010: 21F229A8 2A714C2D 12F16ABF 08E44664!.). *... qL j... FD

    0020: 0D95A510 0AFFA63B 815CCBB0 B7C708CF...; \......

    0030: 31246316 0E93E084 59395461 118C 9251 $1 c... Y9Ta... Q

    0040: 823A36CB 55F2F59C 3342326D 251F8B7A. : 6.U... 3B2m %... z

    0050: B9C9F916 C403A4D1 59DA3AA8 932312C 0... Y.:.. #..

    0060: 88476460 E9C9A07C 5671C18D A9202382. GD'... | DV... #.

    0070: 441F47AF 74E407B1 DB06B929 406E993D D.G.t...) @n. =

    0080: A7C149FA 1677D1A2 E3105356 4E205E45... I have... w... SVN ^ E

    0090: 06D2CB2A B6BF638E 0910283C 7FF6BAE2... *... c... (<>

    00 to 0: 3F97ADF5 19B 78872 69C0346B 7EF89FAE?... ri.4k... ~

    00B 0: 456E26CF 52CC296B 11F6AE68 2498024C en &. R) k...h$... L

    00C 0: 74658112 you 16121A 68 h

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IOS treatment keep alive payload: proposal = 32767/32767 sec.

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, DPD received VID

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, trying to find the group via IKE ID...

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, connection landed on tunnel_group 80.62.240.136

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, ID type homologous 1 received (IPV4_ADDR)

    Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, identity of IKE for peer name incompatibility Cert subject Alt

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, case of mistaken IKE MM Responder WSF (struct & 0xd3dcecf0) , : MM_DONE, EV_ERROR--> EV_COMPARE_IDS--> MM_BLD_MSG6, MM_BLD_MSG6, NullEvent--> MM_BLD_MSG6, EV_VALIDATE_CERT--> MM_BLD_MSG6, EV_UPDATE_CERT--> MM_BLD_MSG6, EV_TEST_CERT--> MM_BLD_MSG6, EV_CHECK_NAT_T, EV_CERT_OK--> MM_BLD_MSG6

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, IKE SA MM:1e531705 ending: 0x0100c002, refcnt flags 0, tuncnt 0

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, sending clear/delete with the message of reason

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, payload of empty hash construction

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, constructing the payload to delete IKE

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, build payloads of hash qm

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 5a228b67) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80

    Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, Removing peer to peer table does not, no match!

    Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, error: cannot delete PeerTblEntry

    Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)

    Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68

    Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)

    Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68

    Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)

    Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68

    Then, it waits a bit and start over. No matter if I am trying to establish the tunnel network or remote endpoint - there is no difference in the result.

    I made a line of debug output "BOLD" - I don't the have not seen this before, don't think that devices Cisco used this alternative area? Thought it was Microsoft?

    1 thing is a reference to the certificates - I use my won Microsoft PKI based on 2003 servers. I have 1 Root CA and 2 subordinates. The root CA is stopped. During the construction of my trustpoints, I start to do my request, give it to one of subordinates, gets my identity certificate and save it on my computer. Then check the chain, which looks always good - RootCA-> SubordinateCA-> ClientCert. Then I extracted the subordinate cert, to authenticate my trustpoint and finally I import the certificate of identity. No complaints, it of all good - and actually working like a charm for my EZVPN configurations.

    So I do not think the problem it's with the certificates, although the release said that there is an incompatibility with the other name in question.

    The debugging online after this statement, I understand not quite - maybe someone can help me with this? Because right after this line, he begins to destroy the tunnel.

    I can provide from configs if necessary, but really, it corresponds to the configuration contained in the guide.

    / Peter

    Can you check the "crypto isakmp identity" command on both sides?  He looks like a side sends the IP, when it expected the certificate DN is the name so it can match the value in the cert.

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, ID type homologous 1 received (IPV4_ADDR)

    Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, identity of IKE for peer name incompatibility Cert subject Alt

    -Jason

  • Period of Continous Pings VPN

    Thanks in advance.

    I have an ASA5505 to a remote location and an ASA5550 to my loocation...

    I get the following info in my logs:

    IP = 62.73.210.70, invalid header, lack of payload SA! (next payload = 4)

    Group = 62.73.210.70, IP = 62.73.210.70, no pre-shared key configured for group

    Group = 62.73.210.70, IP = 62.73.210.70, impossible to find a group valid tunnel, abandonment...!

    Group = 62.73.210.70, IP = 62.73.210.70, Removing peer to peer table does not, no match!

    Group = 62.73.210.70, IP = 62.73.210.70, error: cannot delete PeerTblEntry

    Copy config as follows:

    Distance: 172.25.62.226 has been statically NAT' public 62.73.210.70 ed.

    Remote configuration:

    interface Vlan1
    nameif inside
    security-level 100
    IP 10.200.1.209 255.255.255.240
    !
    interface Vlan2
    nameif outside
    security-level 0
    IP 172.25.62.226 255.255.255.248
    !
    interface Ethernet0/0
    switchport access vlan 2

    10.200.1.208 IP Access-list extended sheep 255.255.255.240 allow 10.199.1.0 255.255.255.0
    10.200.1.208 IP Access-list extended sheep 255.255.255.240 allow 10.10.144.0 255.255.252.0
    Access extensive list ip 10.200.1.208 VPNL2L allow 255.255.255.240 10.199.1.0 255.255.255.0
    Access extensive list ip 10.200.1.208 VPNL2L allow 255.255.255.240 10.10.144.0 255.255.252.0
    allowed extended access list 100 tcp host 89.254.12.35 host 10.200.1.213 eq www
    pager lines 24
    Within 1500 MTU
    Outside 1500 MTU
    ICMP unreachable rate-limit 1 burst-size 1
    don't allow no asdm history
    ARP timeout 14400
    Global 1 interface (outside)
    NAT (inside) 0 access-list sheep
    NAT (inside) 1 0.0.0.0 0.0.0.0
    Route outside 0.0.0.0 0.0.0.0 172.25.62.225 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    the ssh LOCAL console AAA authentication
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp - esp-md5-hmac mytrans
    address for correspondence card crypto mymap 10 VPNL2L
    card crypto mymap 10 peers set 65.181.59.210
    mymap 10 transform-set mytrans crypto card
    3600 seconds, duration of life card crypto mymap 10 set - the security association
    mymap outside crypto map interface
    crypto isakmp identity address
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10
    preshared authentication
    the Encryption
    md5 hash
    Group 2
    life 86400
    Crypto isakmp nat-traversal 2

    tunnel-group 65.181.59.210 type ipsec-l2l
    IPSec-attributes tunnel-group 65.181.59.210
    pre-shared-key *.
    !
    class-map inspection_default
    match default-inspection-traffic

    My location Config:

    interface GigabitEthernet0/0
    nameif outside
    security-level 0
    IP 65.181.59.210 255.255.255.240
    !
    interface GigabitEthernet0/1
    nameif inside
    security-level 100
    IP 10.199.1.2 255.255.255.0

    DNS server-group DefaultDNS

    permit same-security-traffic inter-interface
    permit same-security-traffic intra-interface
    WML tcp service object-group
    Description of the data access remote wits
    Beach of port-object 1 65535

    access-list extended aclin allowed object-group DM_INLINE_PROTOCOL_5 10.199.1.2 host 65.181.59.210

    Note to access local rules no.-nat-list
    access-list no. - nat extended ip Rignet 255.255.255.0 allow 10.10.144.0 255.255.252.0
    Note to access local rules no.-nat-list
    access-list extended no. - nat ip Rignet 255.255.255.0 ConocoNova 255.255.255.240 allow
    Note No.-nat-ConocoNova access list

    access-list no. - nat extended ip Rignet 255.255.255.0 allow ENI 255.255.255.240
    access-list no. - nat extended ip 10.10.144.0 allow 255.255.252.0 ENI 255.255.255.240
    access-list extended no. - nat ip Rignet 255.255.255.0 Norway_Office 255.255.255.240 allow
    access-list no. - nat extended ip 10.10.144.0 allow 255.255.252.0 Norway_Office 255.255.255.240
    access-list extended no. - nat ip Rignet 255.255.255.0 BobbyVPN 255.255.255.0 allow
    access-list no. - nat extended ip 10.10.144.0 allow 255.255.252.0 BobbyVPN 255.255.255.0

    Note to inside_access_in access list block port 135 for the port scan
    inside_access_in list extended access deny 135 a
    inside_access_in list extended access allowed object-group DM_INLINE_PROTOCOL_4 10.10.144.0 255.255.252.0 Rignet 255.255.255.0
    test the access list extended permit icmp any any echo
    test from the list of access permit icmp any any echo response
    Allow InsideNOV_access_in to access extended list ip 10.200.0.0 255.255.0.0 10.10.144.0 255.255.252.0
    InsideNOV_access_in list extended access allow DM_INLINE_SERVICE_7 of object-group a
    InsideNOV_access_in list extended access allowed object-group DM_INLINE_SERVICE_4 Rignet 255.255.255.0 10.10.144.0 255.255.252.0
    InsideNOV_access_in list extended access allowed object-group DM_INLINE_PROTOCOL_12 Norway_Office 255.255.255.240 10.10.144.0 255.255.252.0
    InsideNOV_access_in list extended access allowed object-group DM_INLINE_PROTOCOL_8 BobbyVPN 255.255.255.0 10.10.144.0 255.255.252.0
    inside_acl list extended access allow DM_INLINE_SERVICE_8 of object-group a
    inside_acl list extended access allowed object-group DM_INLINE_SERVICE_5 10.10.144.0 255.255.252.0 Rignet 255.255.255.0
    inside_acl list extended access allowed object-group DM_INLINE_SERVICE_6 Rignet 255.255.255.0 10.10.144.0 255.255.252.0
    inside_acl list extended access allowed object-group DM_INLINE_PROTOCOL_10 10.200.0.0 255.255.0.0 255.255.255.0 Rignet
    inside_access_in_1 list extended access allowed object-group DM_INLINE_PROTOCOL_7 BobbyVPN 255.255.255.0 255.255.255.0 Rignet
    allow inside_access_in_1 to access extended list ip 10.200.0.0 255.255.0.0 255.255.255.0 Rignet
    outside_cryptomap list extended access allowed object-group DM_INLINE_PROTOCOL_13 65.181.59.210 host 10.200.1.222
    inside_access_in_2 list extended access allowed object-group Rignet DM_INLINE_SERVICE_11 255.255.255.0 255.255.255.0 Rignet
    outside_cryptomap_1 list extended access allowed object-group DM_INLINE_PROTOCOL_14 65.181.59.210 host 10.200.1.222
    pager lines 24
    Enable logging
    asdm of logging of information

    ASDM image disk0: / asdm - 621.bin
    don't allow no asdm history
    ARP timeout 14400
    Global 1 interface (outside)
    Global (inside) 2 65.181.57.51 mask 255.255.255.255 subnet
    NAT (outside) 1 0.0.0.0 0.0.0.0
    NAT (inside) - access list 0 no - nat
    NAT (inside) 1 Rignet 255.255.255.0
    NAT (inside) 1 0.0.0.0 0.0.0.0
    public static 65.181.59.222 (Interior, exterior) 10.199.1.23 netmask 255.255.255.255
    public static 65.181.59.219 (Interior, exterior) 10.199.1.27 netmask 255.255.255.255
    public static 65.181.59.216 (Interior, exterior) 10.199.1.29 netmask 255.255.255.255
    Access-group aclin in interface outside
    inside_access_in_1 access to the interface inside group

    Route outside 0.0.0.0 0.0.0.0 65.181.59.209 1
    Route inside 153.15.156.217 255.255.255.255 65.181.57.51 1

    dynamic-access-policy-registration DfltAccessPolicy

    Sysopt connection tcpmss 1100
    Sysopt noproxyarp inside
    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set esp - esp-md5-hmac RIGHT
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    dynamic-map crypto myDYN-card 5 transform-set RIGHT
    set life - the association of security crypto dynamic-map myDYN-card 5 28800 seconds
    kilobytes of life Dynamics-card crypto myDYN-card 5 set security-association 4608000
    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    card crypto myMAP 1 match address outside_cryptomap_1
    card crypto myMAP 1 set peer 62.73.210.70
    card crypto myMAP 1 transform-set RIGHT
    dynamic crypto 65000 isakmp ipsec myDYN-map myMAP map
    myMAP outside crypto map interface
    Crypto ca trustpoint Intelliserv.rignet.local

    Crypto ca trustpoint ASDM_TrustPoint3
    Configure CRL
    Crypto ca trustpoint ASDM_TrustPoint0

    crypto isakmp identity address
    crypto ISAKMP allow outside
    crypto ISAKMP policy 1
    preshared authentication
    the Encryption
    md5 hash
    Group 2
    life 86400
    Crypto isakmp nat-traversal 21

    attributes of Group Policy DfltGrpPolicy
    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
    internal group myGROUP strategy
    Group myGROUP policy attributes
    Split-tunnel-policy tunnelspecified
    allow to NEM
    internal group ENI policy
    attributes of ENI Group Policy
    Protocol-tunnel-VPN IPSec

    IPSec-attributes tunnel-group DefaultL2LGroup
    pre-shared-key *.
    type tunnel-group mytunnel remote access
    tunnel-group mytunnel General-attributes
    strategy - by default-group myGROUP
    mytunnel group of tunnel ipsec-attributes
    pre-shared-key *.
    tunnel-group 164.85.0.18 type ipsec-l2l
    IPSec-attributes tunnel-group 164.85.0.18
    validation by the peer-id cert
    string
    tunnel-group 62.73.210.70 type ipsec-l2l
    tunnel-group 62.73.210.70 General-attributes
    Group Policy - by default-ENI
    by default-group DefaultL2LGroup tunnel-Group-map
    !
    class-map inspection_default
    match default-inspection-traffic

    I don't see a group of tunnel and psk associated with your primary location for the remote site 5505 outside interface.

    Sent by Cisco Support technique iPad App

  • Update Vista SP2 - lack of File_CSI_0x00000002_\winsxs\x86_microsoft-windows-sidebar_ payload

    When you try to install the Vista SP2 I get errors - following
    (f) lack of payload file CSI 0 x 00000002 \winsxs\x86_microsoft-windows-sidebar_31bf3856ad364e35_6.0.6000.16386_none_cca5e9c129bd0a02\settings.ini Microsoft-Windows-Sidebar, Culture = neutral, Version = 6.0.6000.16386, PublicKeyToken = 31bf3856ad364e35, ProcessorArchitecture = x 86, versionScope = NonSxS
    (f) lack of payload file CSI 0 x 00000002 \winsxs\x86_microsoft-windows-sidebar_31bf3856ad364e35_6.0.6000.16615_none_ccf09e9d29852489\settings.ini Microsoft-Windows-Sidebar, Culture = neutral, Version = 6.0.6000.16615, PublicKeyToken = 31bf3856ad364e35, ProcessorArchitecture = x 86, versionScope = NonSxS
    (f) lack of payload file CSI 0 x 00000002 \winsxs\x86_microsoft-windows-sidebar_31bf3856ad364e35_6.0.6000.20740_none_cd54ca3242bf9973\settings.ini Microsoft-Windows-Sidebar, Culture = neutral, Version = 6.0.6000.20740, PublicKeyToken = 31bf3856ad364e35, ProcessorArchitecture = x 86, versionScope = NonSxS
    (f) lack of payload file CSI 0 x 00000002 \winsxs\x86_microsoft-windows-sidebar_31bf3856ad364e35_6.0.6001.18000_none_cedcabbd26a81ad6\settings.ini Microsoft-Windows-Sidebar, Culture = neutral, Version = 6.0.6001.18000, PublicKeyToken = 31bf3856ad364e35, ProcessorArchitecture = x 86, versionScope = NonSxS

    and
    Found 4 errors
    CSI lack payload Total number of files: 4
    CSI information Total Count: 1

    I tried all the suggestions like running the Mr. Fixit, System tool and downloaded the file and install from my hard drive - nothing works. I bought my laptop with Vista pre-installed and there is no way for to run me a repair, it seems, unless anyone has any suggestions - it seems that I re - install everything from scratch or perhaps upgrade to Windows 7.

    It's the only update that seems to have the problem - as the individual updates through the fine.

    Any suggestion or help would be greatly appreciated.

    You don't want to try a Win7 update with the computer in its current state.

    If your computer came with a set of disks, there is a hidden restore partition (not to be confused with the system restore, please) you would use to reinstall Vista.

    Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support, initially planned to end on November 26, 2009, has been extended until February 26, 2010. Availability of support chat or messaging differs depending on your location. Some questions may require that more support for which he is advanced a charge.  Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; Problems after installing a service pack).

    ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • Use of id id push and BB10 payload?

    I'm relatively new to push stuff so this may be covered elsewhere. I can't find anything by searching in the forums.

    When you push send, the PAP contains a push-id attribute. This seems to be an arbitrary string that I can specify.

    When you receive a helping hand, the PushPayload has an id() which is a string, also described as "Returns the identifier push.". It seems it can be defined by the system and not related to what whatsoever in the offensive itself and so far seems to have the value "_".

    Is there a relationship between these?

    What is the purpose of the attribute id push?  I do shoot 'open loop' through BIS with the Push of basic service (no further), so my assumption is if I were using more or send Push through BES10 it would be a symbol that is useful to query the status of the push.

    What is the purpose of the id property of PushPayload, and whether it was true that the docs say it returns the identifier of 'push', then what is the identifier to push and there at - it unconnected with the id push above property?

    Thanks for any comments you may have.

    Hi Peter,.

    What you think makes sense however, after receiving a history lesson on the whole situation, I found that it is essentially a bug. Really the push-id value must get past and power be read from the field PushPayload #id however the Push server don't currently even past this value down to the client. The push-id is useful today if you push through a BES or push more to query the status of a sudden thumb or cancelling a helping hand.

    The field read you of PushPayload #id is actually automatically generated on the client if no ID push is received, which explains why he has no resemblance with... something useful.

    There is a solution! You can add this header to the payload section to push your server 'Push-Message-ID' Push, giving your payload with a structure like:

    -asdfglkjhqwert
    Content-Type: text/plain
    Push-Message-ID:


    -asdfglkjhqwert-

    I tried this out and it works well, gives the expected client-side value.

  • Service SQL Server 2014 will not start start after the update sp1 (KB3058865, KB3075950, KB3094221)

    Hi, my SQL Server 2014 works very well in my server with WIndows 2012 until I installed the new day & service pack that was required for server hardening.

    I successfully installed SP1 KB 3058865 first, then discovered that the services do not start. After so much research to fix, I came with the 2 cu updates KB3075950, KB3094221 in knowing that it could solve my problem but unfortunately is not.

    I also tried to change the service account that many suggest, but his does not work.

    I tried to replace the master file & maslog but also failed.

    I tried to run etc and unique usermode and restore master db... also failed.

    Here is the log file:

    16/02/01 15:21:21.83 Server Microsoft SQL Server 2014 (SP1 - CU3) (KB3094221) - 12.0.4427.24 (X 64)
    October 10, 2015 17:18:26
    Copyright (c) Microsoft Corporation
    Standard Edition (64-bit) on Windows NT 6.2 (build 9200 :) (hypervisor)

    2016-02-01 15:21:21.84 setting the server UTC: 08:00
    2016-02-01 15:21:21.84 Server (c) Microsoft Corporation.
    2016-02-01 15:21:21.84 server all rights reserved.
    2016-02-01 15:21:21.84 server process ID is 5128.
    2016-02-01 15:21:21.86 Server system manufacturer: "Microsoft Corporation", model of system: 'Virtual Machine '.
    2016-02-01 15:21:21.86 the server's authentication mode is MIXED.
    2016-02-01 15:21:21.86 Server record SQL Server messages in file ' C:\Program Files\Microsoft SQL Server\MSSQL12. MSSQLSERVER\MSSQL\Log\ERRORLOG'.
    2016-02-01 15:21:21.86 Server service account is "NT Service\MSSQLSERVER". This is an informational message; no user action is required.
    2016-02-01 15:21:21.86 registry server startup parameters:
    -d C:\Program Files\Microsoft SQL Server\MSSQL12. MSSQLSERVER\MSSQL\DATA\master.mdf
    e C:\Program Files\Microsoft SQL Server\MSSQL12. MSSQLSERVER\MSSQL\Log\ERRORLOG
    l C:\Program Files\Microsoft SQL Server\MSSQL12. MSSQLSERVER\MSSQL\DATA\mastlog.ldf
    2016-02-01 15:21:21.86 Server startup command line parameters:
    s 'MSSQLSERVER '.
    2016-02-01 15:21:22.27 Server SQL Server has detected 1 struggling with 1 cores per socket and 1 logical processors per socket, 1 total logical processors; using 1 logical processors based on SQL Server licenses. This is an informational message; no user action is required.
    2016-02-01 15:21:22.27 Server SQL Server starts at the normal base priority (= 7). It is an informational message only. No user action is required.
    2016-02-01 15:21:22.28 Server has detected 7999 MB of RAM. This is an informational message; no user action is required.
    2016-02-01 15:21:22.28 Server using conventional memory in the memory manager.
    2016-02-01 15:21:22.33 default server collation: SQL_Latin1_General_CP1_CI_AS (us_english 1033)
    2016-02-01 15:21:22.37 Server this instance of SQL Server is a latest report by using a process ID of 1600 at 01/02/2016 15:13:12 (local) 01/02/2016 07:13:12 (UTC). This is an informational message only; no user action is required.
    2016-02-01 15:21:22.38 the maximum number of connections administrator dedicated to this server instance is '1 '.
    2016-02-01 15:21:22.38 configuration of server node: node 0: CPU mask: 0 x 0000000000000001:0 Active CPU mask: 0 x 0000000000000001:0. This message provides a description of the NUMA configuration for this computer. It is an informational message only. No user action is required.
    2016-02-01 15:21:22.40 allocation of dynamic locking using the server.  Initial allocation of blocks of lock of 2500 and 5000 per node lock owner.  It is an informational message only.  No user action is required.
    2016-02-01 15:21:22.43 spid8s start database 'master '.
    2016-02-01 15:21:22.49 Server CLR version loaded v4.0.30319.
    2016-02-01 15:21:22.51 spid8s d - 8 operations in the database 'master' (1:0). It is an informational message only. No user action is required.
    2016-02-01 15:21:22.61 Server common language features (CLR) runtime initialized using CLR version C:\Windows\Microsoft.NET\Framework64\v4.0.30319\ v4.0.30319.
    2016-02-01 15:21:22.62 spid8s 0 operations cancelled in database 'master' (1:0). It is an informational message only. No user action is required.
    2016-02-01 15:21:22.62 spid8s Recovery is writing a checkpoint in database 'master ' (1). It is an informational message only. No user action is required.
    2016-02-01 15:21:22.79 spid8s SQL Server Audit begins audits. This is an informational message. No user action is required.
    2016-02-01 15:21:22.80 spid8s SQL Server Audit has begun audits. This is an informational message. No user action is required.
    2016-02-01 15:21:22.88 spid8s Trace SQL ID 1 was launched by the "sa" login
    2016-02-01 15:21:23.28 spid8s server name is "UATCASADB". It is an informational message only. No user action is required.
    2016-02-01 15:21:23.28 spid13s A self-generated certificate was loaded successfully for encryption.
    2016-02-01 15:21:23.33 spid13s Server listens on ['none' 1433].
    2016-02-01 15:21:23.40 spid13s Server listens on ['none' 1433].
    local connections provider 2016-02-01 15:21:23.44 spid13s server is ready to accept connection on [\\.\pipe\SQLLocal\MSSQLSERVER].
    local connections provider 2016-02-01 15:21:23.44 spid13s server is ready to accept connection on [\\.\pipe\sql\query].
    2016-02-01 15:21:23.48 Server Server listens on [: 1 1434].
    2016-02-01 15:21:23.49 Server Server listening on [127.0.0.1 1434 ].
    2016-02-01 15:21:23.49 connection admin support dedicated server was created for locally listening on port 1434.
    2016-02-01 15:21:23.49 Server SQL Server attempts to save an of Service Principal name (SPN, service principal name) for the SQL Server service. Kerberos authentication is not possible, until a name for the SQL Server service is SPN. This is an informational message. No user action is required.
    2016-02-01 15:21:23.60 spid14s A new instance of the full-text filter daemon host process has been started successfully.
    2016-02-01 15:21:23.71 Server SQL Server Network Interface library successfully registered the Service Principal Name (SPN) [MSSQLSvc/UATCASADB.onenetworkbank.com.ph] for the SQL Server service.
    2016-02-01 15:21:23.72 Server SQL Server Network Interface library successfully registered the Service Principal Name (SPN) [MSSQLSvc/UATCASADB.onenetworkbank.com.ph:1433] for the SQL Server service.
    2016-02-01 15:21:23.97 spid17s start database 'msdb '.
    2016-02-01 15:21:23.98 spid18s database startup "ReportServer".
    2016-02-01 15:21:23.98 spid19s database startup 'ReportServerTempDB '.
    2016-02-01 15:21:24.03 spid9s start database 'mssqlsystemresource '.
    2016-02-01 15:21:24.08 spid9s the base resource database build version is 12.00.4427. It is an informational message only. No user action is required.
    Error logon 2016-02-01 15:21:24.11: 18401, severity: 14, State: 1.
    2016-02-01 15:21:24.11 of logon login failed for user "NT SERVICE\ReportServer". Reason: The server is in script upgrade mode. Only one administrator can connect at this time. [CLIENT: ]
    2016-02-01 15:21:24.18 spid19s 1 transactions rolled forward in the 'ReportServerTempDB' (6:0) database. It is an informational message only. No user action is required.
    2016-02-01 15:21:24.28 spid19s 0 transactions cancelled in the database 'ReportServerTempDB' (6:0). It is an informational message only. No user action is required.
    2016-02-01 15:21:24.44 spid17s 133 transactions rolled forward in the database 'msdb' (4:0). It is an informational message only. No user action is required.
    2016-02-01 15:21:24.73 spid17s 0 transactions cancelled in the database 'msdb' (4:0). It is an informational message only. No user action is required.
    2016-02-01 15:21:24.74 spid17s Recovery is writing a checkpoint in database 'msdb' (4). It is an informational message only. No user action is required.
    2016-02-01 15:21:24.79 spid9s start database 'model '.
    2016-02-01 15:21:25.01 spid9s clearing tempdb database.
    2016-02-01 15:21:25.94 spid9s start database 'tempdb '.
    2016-02-01 15:21:26.12 spid20s The Service Broker endpoint is in a disabled or stopped state.
    2016-02-01 15:21:26.12 spid20s The Database Mirroring endpoint is disabled or stopped state.
    Manager of Service Broker 2016-02-01 15:21:26.15 spid20s began.
    2016-02-01 15:21:27.32 spid8s database 'master' is upgrading script 'msdb110_upgrade.sql' of level 201328592 level 201331019.
    2016-02-01 15:21:27.32 spid8s-
    2016-02-01 15:21:27.32 spid8s start PRE_MSDB execution. SQL
    2016-02-01 15:21:27.32 spid8s-
    2016-02-01 15:21:28.36 spid8s configuration database COMPATIBILITY_LEVEL option for 100 for database 'msdb '.
    2016-02-01 15:21:28.56 spid8s-
    2016-02-01 15:21:28.56 spid8s start PRE_SQLAGENT100 execution. SQL
    2016-02-01 15:21:28.56 spid8s-
    2016-02-01 15:21:28.60 spid8s configuration database option COMPATIBILITY_LEVEL of 120 for the database 'msdb '.
    2016-02-01 15:21:28.77 spid8s Configuration option 'allow updates' goes from 1 to 1. Run the RECONFIGURE statement to install.
    2016-02-01 15:21:28.77 spid8s Configuration option 'allow updates' goes from 1 to 1. Run the RECONFIGURE statement to install.
    Error logon 2016-02-01 15:21:29.18: 18401, severity: 14, State: 1.
    2016-02-01 15:21:29.18 of logon login failed for user "NT SERVICE\ReportServer". Reason: The server is in script upgrade mode. Only one administrator can connect at this time. [CLIENT: ]
    2016-02-01 15:21:31.84 spid8s attempting to load library 'xpstar.dll' in memory. It is an informational message only. No user action is required.
    "2016-02-01 by using spid8s 15:21:31.86"xpstar.dll' version ' 2014.120.4100 ' to run the extended stored procedure 'xp_instance_regread '. This is an informational message only; no user action is required.
    2016-02-01 15:21:31.89 spid8s DBCC TRACEOFF 1717, process server ID (SPID) 8. This is an informational message only; no user action is required.
    2016-02-01 15:21:31.89 spid8s DBCC execution completed. If DBCC printed in error messages, contact your system administrator.
    2016-02-01 15:21:31.90 spid8s
    2016-02-01 15:21:31.90 spid8s create table temp_sysjobschedules
    2016-02-01 15:21:32.20 spid8s
    2016-02-01 15:21:32.20 spid8s Alter table sysdownloadlist...
    2016-02-01 15:21:32.22 spid8s
    2016-02-01 15:21:32.22 spid8s Alter table sysjobhistory...
    2016-02-01 15:21:32.24 spid8s
    2016-02-01 15:21:32.24 spid8s Alter table systargetservers...
    2016-02-01 15:21:32.25 spid8s
    2016-02-01 15:21:32.25 spid8s Alter table sysjobsteps...
    2016-02-01 15:21:32.40 spid8s Configuration option 'allow updates' goes from 1 to 0. Run the RECONFIGURE statement to install.
    2016-02-01 15:21:32.40 spid8s Configuration option 'allow updates' goes from 1 to 0. Run the RECONFIGURE statement to install.
    2016-02-01 15:21:32.42 spid8s
    2016-02-01 15:21:32.42 spid8s-
    2016-02-01 15:21:32.42 spid8s PRE_SQLAGENT100 execution. Full SQL
    2016-02-01 15:21:32.42 spid8s-
    2016-02-01 15:21:32.46 spid8s DMF pre-shaping within walking distance...
    2016-02-01 15:21:32.83 spid8s DC pre-shaping within walking distance...
    2016-02-01 15:21:32.83 spid8s check if Data collector config table exists...
    2016-02-01 15:21:32.84 spid8s State of collector of data before the update: 0
    2016-02-01 15:21:32.84 spid8s pre_dc100::Check if syscollector_collection_sets_internal table exists...
    2016-02-01 15:21:32.84 spid8s pre_dc100::Capturing Collection to define the status of temporary table...
    2016-02-01 15:21:33.05 spid8s Deleting cached generated automatically collect T - SQL packages to msdb data...
    2016-02-01 15:21:33.05 spid8s end of the DC pre-staged to level as follows.
    2016-02-01 15:21:33.05 spid8s DAC pre-shaping within walking distance...
    2016-02-01 15:21:33.06 spid8s from CAD pre-shaping within walking distance...
    2016-02-01 15:21:33.06 spid8s end of the CAD pre-staged to level as follows.
    2016-02-01 15:21:33.06 spid8s-
    2016-02-01 15:21:33.06 spid8s start execution of MSDB. SQL
    2016-02-01 15:21:33.06 spid8s-
    2016-02-01 15:21:33.19 spid8s Configuration option 'allow updates' from 0 to 1. Run the RECONFIGURE statement to install.
    2016-02-01 15:21:33.19 spid8s Configuration option 'allow updates' from 0 to 1. Run the RECONFIGURE statement to install.
    2016-02-01 15:21:33.37 spid8s check the size of the MSDB.
    2016-02-01 15:21:33.63 spid8s error: 8966, severity: 16, State: 2.
    2016-02-01 15:21:33.63 spid8s can not read and lock the page (1:56616) with lock type SH. page no ID invalid. has failed.
    2016-02-01 15:21:33.63 spid8s error: 8946, severity: 16, State: 12.
    2016-02-01 15:21:33.63 spid8s Table error: Allocation page (1:56616) has invalid header values to the PFS_PAGE page. The type is 0. Check the type, unit ID of ID and the ID of the page on the page.
    2016-02-01 15:21:33.63 spid8s error: 912, severity: 21, State: 2.
    2016-02-01 15:21:33.63 spid8s Script level upgrade for database 'master' failed because upgrade step 'msdb110_upgrade.sql' has detected 3601, an error state 5, severity 25. It is a serious condition that could interfere with the normal operation and the database is taken offline. If the error occurred during the upgrade of the 'master' database, it will prevent the entirety of a SQL Server instance to start. Review the previous entries in the error log, take appropriate corrective action and restart the database so that the script upgrade steps run until the end.
    2016-02-01 15:21:33.64 spid8s error: 3417, severity: 21, State: 3.
    2016-02-01 15:21:33.64 spid8s cannot recover the master database. SQL Server cannot run. Master of restoring a full backup, repair or rebuild. For more information on how to rebuild the master database, see the SQL Server online documentation.
    2016-02-01 15:21:33.64 spid8s stop SQL Server launched
    2016-02-01 15:21:33.64 spid8s trace SQL stopped due to server shutdown. Trace ID = "1". This is an informational message only; no user action is required.
    2016-02-01 15:21:34.70 spid8s error: 25725, severity: 16, State: 1.
    2016-02-01 15:21:34.70 spid8s an error occurred trying to empty sessions extended all running events.  Some events may be lost.
    2016-02-01 15:21:34.71 spid13s the SQL Server Network Interface library could not deregister the Service Principal Name (SPN) [MSSQLSvc/servername.urldomain] for the SQL Server service. Error: 0x2af9, State: 61. Administrator should deregister this SPN manually to avoid client authentication errors.
    2016-02-01 15:21:34.71 spid13s the SQL Server Network Interface library could not deregister the Service Principal Name (SPN) [MSSQLSvc / servername.urldomain:1433] for the SQL Server service. Error: 0x2af9, State: 61. Administrator should deregister this SPN manually to avoid client authentication errors.

    -----------------------------------------------------------------------------------------------

    I would be grateful for all the help I can get. Thank you.

    Hello

    Your question is beyond the scope of this community.

    Please repost your question in the SQL Server TechNet Forums.

    https://social.technet.Microsoft.com/forums/SQLServer/en-us/home?category=SQLServer

    TechNet Server forums.

    http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

    See you soon.

  • X 3000 of untrusted routing

    Hello

    I would just like to know if anyone heard about a future for the X 3000 firmware version that would solve the problems of routing.

    Since the day 1 (a few months ago), I've known routing performance in time with the X 3000. I use this unit only as a router, but it seems to lose track of the routing tables after a few days or a few weeks. Restart the modem solve the problem from time to time, but most of the time, I need to reset and reconfigure the entire thing. So I'm ok for a few days.

    My home network is very stable - no new deivces, regular operations and nothing fancy.

    The obvious problems, I noticed:

    * Some devices cannot access my NAS, while they could and will be able to after reboot of the router or the re-configuration.

    * List of DHCP clients completely wrong: LAN / WAN confusion, MAC address is not not the right device name, worn charracter set

    Web UI does not completely: the missing piece of information in the header, lack of menus (sharing), etc.

    * Identified a bug that is related to the SSID name: use of some characters (always in the spec of IEEE802.11) will prevent the DHCP client table to shown!

    If no new firmware is announced, I just bring this crapy device and get a refund. I'm done with exhibition using their clients as testers for their solfware.

    Routing of the stable seams with new MTU to 1400. The firmware is still buggy but to the less internet and local network access to ares mooth and without problem. Thank you.

  • Internet subscribers

    Hope someone can point me in the right direction. Due to problems of customer I can not use the option "transfer system." Can someone tell me the correct format to use to create a CSV file for Internet subscribers? I tried several combinations of headers but still get errors describing the invalid characters in the columns, or sometimes an error describing the header information not valid.

    Also is there a CSV file format to create several call handlers? Thank you

    Unity 4.0.4 SR1

    CCM 3.3.3 SR1

    It was just the commas to end that you had on all your lines... when the parser detects a comma, it is expected that there will be a field on the right side of it, non-empty (this is what is meant by '[] is an invalid header' - white is not legal).

    I removed your back commas and it imported just dandy on my test system.

  • Edition of sequences playing bigger than the original clips

    I'm a first novice user, although I have used the program for centuries in what looks like a different life, so I am still struggling to remember the basics! I have set up a project and was pleased to play the version over on my tv when do, I discovered that all the heads were cut off the video, when they look good on the clips of images. I'm sure it's a quick configuration change, but I can't just not work how to do this, then I would be very grateful if someone could help it. It's like the clips appear slightly larger in the modified version, and is why the heads lack.

    Thank you.

    Change the zoom is perhaps not the best solution to your problem - it's a band-aid on the problem and not a real difficulty.

    As others have mentioned, the sequence settings must match the sequence. Right click on a clip in the project bin and choose new sequence of the Clip , and then clips will be correct appearance in this sequence, then export with the same parameters (size of the framework, cadence, fields, the pixel aspect, etc.) for best results.

    The timeline will be always greater of your clips, don't you worry in this regard. When you export, it will export only at the end of the last item and no more.

    Thank you

    The f

  • I bought a new and a better computer, but now it is impossible to reinstall my CS6

    I bought CS6 in 2012. I bought a new and a better computer, but now it is impossible to reinstall my CS6. I get an error during installation (see below)

    a.jpg

    and some fetchers do not work (as when I try the recovery tool "save for web" I get: the system can not fined the specified path) .

    b.png


    What can I do?



    This is the log I get at the end of the installation:

    Exit code: 6

    Please see the faults and warnings below for troubleshooting. For example, ERROR: DW050...

    --------------- Summary ------------------------------

    -0 fatal Error (s), 12 (s), 0 warning (s)

    -Payload: {92D58719-BBC1-4CC3-A08B-56C9E884CC2C} Microsoft_VC80_CRT_x86 1.0.0.0.

    ERROR: Error 1327.Invalid Drive: F:\

    ERROR: Install payload MSI failed with the error: - 1603 Fatal error during installation.

    MSI error message: Error 1327.Invalid Drive: F:\

    -Payload: {7E91BB17-16A1-42CE-9502-D6C98BE04920} PDF settings CS6 11.0.0.0.

    ERROR: Error 1327.Invalid Drive: F:\

    ERROR: Install payload MSI failed with the error: - 1603 Fatal error during installation.

    MSI error message: Error 1327.Invalid Drive: F:\

    -Payload: {AC76BA86-1037-0000-7760-000000000005} Acrobat Professional 10.0.0.0.

    ERROR: Error 1327.Invalid Drive: F:\

    ERROR: Install payload MSI failed with the error: - 1603 Fatal error during installation.

    MSI error message: Error 1327.Invalid Drive: F:\

    ERROR: DW050: the following payload errors were found during the installation:

    ERROR: DW050:-Microsoft_VC90_CRT_x86: installation failed

    ERROR: DW050:-CS6 settings PDF: installation failed

    ERROR: DW050:-Microsoft_VC80_CRT_x86: installation failed

    ERROR: DW050:-Acrobat Professional: installation failed

    ERROR: DW050:-Adobe Mini Bridge CS6: installation failed

    ERROR: DW050:-standard Adobe 2.0: installation failed

    Hello

    Please visit https://helpx.adobe.com/creative-suite/kb/errors-exit-code-6-exit.html

    Hope that helps!

    Kind regards

    Sheena

Maybe you are looking for