Period of Continous Pings VPN

Similar Questions

• Problem with ping VPN cisco 877

  Hi all!

  I have a working VPN between a fortigate and a Cisco.

  I have a problem with ping network behind the cisco of the network behind the forti.

  When I ping to vlan2 cisco without problem (192.168.252.1) interface, but I can't ping a server in the vlan2 (192.168.252.2) behind the cisco.

  However the Cisco I can ping the server. In the forti, I see that ping to the interface vlan2 and server in vlan2 take in the same way, and I can see package.

  I post my config could see it it as blocking the ping from 10.41.2.36 to 192.168.252.2 while 192.168.252.1 ping is OK?

  IPSEC #show run
  Building configuration...

  Current configuration: 3302 bytes
  !
  ! Last modification of the configuration at 14:42:17 CEDT Friday, June 25, 2010
  ! NVRAM config update at 14:42:23 CEDT Friday, June 25, 2010
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime localtime show-time zone
  encryption password service
  !
  IPSEC host name
  !
  boot-start-marker
  boot-end-marker
  !
  logging buffered 1000000
  enable secret 5 abdellah
  !
  No aaa new-model
  clock timezone GMT 1
  clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00
  !
  !
  dot11 syslog
  IP cef
  No dhcp use connected vrf ip
  DHCP excluded-address IP 192.168.254.0 192.168.254.99
  DHCP excluded-address IP 192.168.254.128 192.168.254.255
  !
  IP dhcp DHCP pool
  network 192.168.254.0 255.255.255.0
  router by default - 192.168.254.254
  Server DNS A.A.A.A B.B.B.B
  !
  !
  no ip domain search
  name of the IP-server A.A.A.A
  name of the IP-server B.B.B.B
  !
  !
  !
  !
  !
  crypto ISAKMP policy 1
  BA aes 256
  preshared authentication
  Group 5
  ISAKMP crypto key ciscokey address IP_forti
  !
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac vpntest
  !
  myvpn 10 ipsec-isakmp crypto map
  defined by peer IP_forti
  Set transform-set vpntest
  match address 101
  !
  Archives
  The config log
  hidekeys
  !
  !
  !
  !
  !
  interface Tunnel0
  IP 2.2.2.1 255.255.255.252
  source of Dialer0 tunnel
  destination of IP_forti tunnel
  myvpn card crypto
  !
  ATM0 interface
  bandwidth 320
  no ip address
  load-interval 30
  No atm ilmi-keepalive
  DSL-automatic operation mode
  !
  point-to-point interface ATM0.1
  MTU 1492
  bandwidth 160
  PVC 8/35
  VBR - nrt 160 160
  PPPoE-client dial-pool-number 1
  !
  !
  interface FastEthernet0
  switchport access vlan 2
  !
  interface FastEthernet1
  !
  interface FastEthernet2
  !
  interface FastEthernet3
  switchport access vlan 2
  !
  interface Vlan1
  IP 192.168.20.253 255.255.255.0
  IP nat inside
  no ip virtual-reassembly
  !
  interface Vlan2
  IP 192.168.252.1 255.255.255.0
  IP nat inside
  IP virtual-reassembly
  !
  interface Dialer0
  bandwidth 128
  the negotiated IP address
  NAT outside IP
  no ip virtual-reassembly
  encapsulation ppp
  load-interval 30
  Dialer pool 1
  Dialer-Group 1
  KeepAlive 1 2
  Authentication callin PPP chap Protocol
  PPP chap hostname [email protected] / * /
  PPP chap password 7 abdelkrim
  myvpn card crypto
  !
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 Dialer0
  IP route 10.41.2.32 Tunnel0 255.255.255.240
  !
  no ip address of the http server
  no ip http secure server
  The dns server IP
  translation of nat IP tcp-timeout 5400
  no ip nat service sip 5060 udp port
  overload of IP nat inside source list NAT interface Dialer0
  !
  IP access-list standard BROADCAST
  permit of 0.0.0.0
  deny all
  !
  NAT extended IP access list
  IP enable any host IP_cisco
  deny ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
  !
  access-list 101 permit ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
  public RO SNMP-server community
  3 RW 99 SNMP-server community
  SNMP-server community a RO
  SNMP-Server RO community oneCommunityRead
  not run cdp
  !
  !
  !
  control plan
  !
  !
  Line con 0
  password 7 abdelkrim
  opening of session
  no activation of the modem
  line to 0
  line vty 0 4
  password 7 aaaaa
  opening of session
  escape character 5
  !
  max-task-time 5000 Planner
  NTP-period clock 17175037
  Server NTP B.B.B.B
  Server NTP A.A.A.A

  end

  Alex,

  It's your GRE tunnel:

  interface Tunnel0
  IP 2.2.2.1 255.255.255.252
  source of Dialer0 tunnel
  destination of IP_forti tunnel
  myvpn card crypto

  You also have routing set by it.

  You don't need a GRE tunnel, nor do you need the road to tunnel if you want just IPsec tunnel.

• Cannot ping vpn client of 1721 cli on the tunnel endpoint

  I have a 1721 fortunately supporting ipsec vpn client connections. With one small exception, everything works perfectly fine.

  The VPN pool is 10.10.10.1 - 10.10.10.254

  The interface internal f0 is attributed to 192.168.1.254/24.

  In my example:

  Ip address of the VPN client is 10.10.10.5

  The host address of an arbitrary machine on the internal lan is 192.168.1.151

  I am able to ping 192.168.1.151 10.10.10.5

  I'm * not * able to ping 10.10.10.5 192.168.1.254 using the cli on the 1721.

  There is a very good reason to want to solve this problem. I would like to be able to access a tftp server on the client vpn directly from the router in order to download the new startup-config files. Is it possible to get the traffic of vpn-/ tunnel-point endpoint client tftp to travel through the tunnel?

  When you ping from the CLI on the router, the packet will be from the external interface, not the IP address fa0 interface. The VPN client and the router only built a tunnel from the 10.10.10.5 address the 192.168.1.0 network, then the router not cryptera a package that her origin is outside the IP address.

  Try to ping extended to 10.10.10.5 and source of 192.168.1.254 package and see if it works. If it does, you will have also to the source of your TFTP packets from inside interface, you can do with:

  IP tftp source interface fa0

• Inside the server can't ping remote vpn client

  My simple vpn client can accumulate the tunnel vpn with my Office ASA5510 success and my vpn client can ping the internal server. But my internal server cannot ping the remote vpn client. Even the firewall vpn client windows is disable.

  1. in-house server can ping Internet through ASA.

  2 internal server cannot ping vpn client.

  3 Vpn client can ping the internal server.

  Why interal Server ping vpn client? ASA only does support vpn in direction to go?

  Thank you.

  Hello

  Enable inspect ICMP, this should work for you.

  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the icmp
  inspect the icmp error

  inspect the icmp

  

  To configure the ICMP inspection engine, use the command of icmp inspection in class configuration mode. Class configuration mode is accessible from policy map configuration mode.

  inspect the icmp

  HTH

  Sandy

• Site to site VPN router-ASA5505

  Hello

  I have a problem with the VPN between ASA5505 and 3825 router.

  behind the ASA, we have a server that serves the specific port. If for any reason any link is disconnected assets if the VPN will become not we do not generate traffic to this server. After generating even a ping VPN immediately become active and communication starts. another case is when you reboot ASA the VPn is not created without ping server behind this ASA.

  How we could solve this problem without sending a traffing who serve?

  How remote access to this ASA, I can access internal interface? If I open access on port 443 on the external interface of asa could I access it? or I must also exclude this traffic VPN

  I used the VPN Wizard to configure on asa and CLI on router

  some troubleshootingand configuration commands, if this is not enough please let me know what you otherwise.

  Thanks in advance for your help

  ciscoasa # sh crypto isakmp his

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: 10.10.10.1
  Type: L2L role: initiator
  Generate a new key: no State: AM_ACTIVE

  Configuration of the SAA.

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  card crypto outside_map 1 match address outside_1_cryptomap
  card crypto outside_map 1 set pfs Group1
  card crypto outside_map 1 set counterpart 10.10.10.1
  map outside_map 1 set of transformation-ESP-DES-MD5 crypto
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 30
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  the main router configuration

  crypto ISAKMP policy 1
  preshared authentication
  !
  crypto ISAKMP policy 5
  BA 3des
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 10
  preshared authentication
  Group 2
  crypto ISAKMP key 6 _JQfe [BeRGNBCGfbGxxxxxxxxx address 10.10.10.10

  Crypto ipsec transform-set esp - esp-md5-hmac xxxxx

  ETH0 2696 ipsec-isakmp crypto map
  defined peer 10.10.10.10
  Set transform-set xxxxx
  match address 2001

  access-list 2001 permit ip any 192.168.26.96 0.0.0.7

  Post edited by: adriatikb
  I just read somewhere that might change the type VPN "bi-direcitonal' two 'initiator' or 'answering machine' could help me but I test and no results.

  I had the same problem last week, and told the TAC engineer on our service ticket downgrade from IOS 8.2 (3) 8.2 (1).  Since then, it works fine.

• Rattling at startup on Acer 7720

  I posted about it before, but despite the change in power I get it again? To work around the problem, I do a forced reboot and then asks him to load windows normally... .so no problem any ideas? Can you do a test on a test of POST?

  below is the original announcement:

  Convince Folks, can you help me with a problem... I've been using this laptop for some time without problem using windows 7 Ultimate. At the beginning I had problems with the icons when I open a particular program icon I'd get another program?

  So I thought that it is just a mistake and began a reboot... then I had continous ping, but windows starts after 30 to 45 seconds, but with some of the issues previously reported... Then I took the ram and made sure that they were clean and firmly installed and rebooted, but the same issue continues? I then cleaned the system and also checked for viruses, but all came to own. My next step is to Flash the bios and had once again the ping? Puzzled on this I decided to take the laptop to a computer specialist, but took the laptop and not food... when I arrived I went to demonstrate the problem but couldn't? I tried 5 times to shut down and restart and all icons worked with no beep, I couldn't believe it... I took the laptop back at home plugged the power and back came the Bing and errors? IF BY CHANCE it seems to be something to do with food? I leave the laptop a bit run down and then began a reboot... NO rattling? So what - the? any ideas... another .the question I suffer with is when typing the cursor jumps to the top of the window, I type in? also when holding an adventure when you scroll down it immediately jumps back... Its got that me confused! PS: I did a restore to an earlier date and still no go... again I have used this laptop several times before with the same power supply and no problem either!

  Close this thread because it is resolved. And open another thread with your new question/topic. In this case, others can find answers better if they have the same problem. Do not hesitate to give congratulations.

• How to get the status of the servers indeign

  I use indesign server.
  I want to detect if the server is frozen / crashed. Y at - it a command to get the console out permanently. I met heartbeatupdateinterval command line parameter. but I don't know how to use it, because it is not well documented.
  

  Or is there another way to say IndesignServer 'give me an update (console output or any other)"to check the health of InDesign Server.

  heartbeatUpdateInterval is a server parameter that indicates the interval of time (in seconds) during which the last active timestamp of InDesign server is updated on the console.

  Consider using the module with LBQ related to the status of commands like:

  -GetVersion

  -JobStatus

  -QueueStatus

  -IDSStatus

  and also some administrative commands:

  - Ping

  -Kill

  The ping command is what might interest you:

  It would give you timestamp active last server. This command requires no parameters.

  So, you could have your client installation to periodically hit the Ping command for LBQ-health surveillance.

  You could hit more orders as shown above for more details on the State of the server.

• Drops after vMotion network

  Hi all

  I have a problem with vMotion in vSphere and I was wondering if someone could help.

  I currently have 2 hosts which were entirely patches. I have 2 vSwitches. One for management (SC and VMK) and the other for the Virtual Machine. Each vSwtich has 2 adapters physical 1000FDX assigned. The cluster has active HA but DRS not activated and I don't use of FT.

  When I vMotion machines among hosts I loose the customary ping of the virtual machine, but also intermittently the VM gets disconnected for about 2-3 minutes. Probably to about 30% of my vMotions not this way. During this period, you cannot ping the server or anything from the ping server.

  I tried setting the port speed on the network cards on the vSwitch to 1000FDX, tried different vNIC on virtual machines (VMXNET2 and VMXNET3) but still the same problem, but not all the time and it doesn't seem to follow all of the grounds.

  At any come across this before, and how can I solve this problem.

  John

  Could be a problem with your physical switches?

  Can you try to enable RSTP or FastPort?

  You have a single switch or more?

  André

• VPN works, causes periodic freezes of BEFSX41

  I use a BEFSX41 as a firewall/router and site to site vpn.

  While the vpn tunnel is up the router seems to freeze every minute (sometimes after 45 seconds or 30 seconds.

  This is easily evindent when ping the router from another machine on the side of the intranet. While the average ping time is less than 1 milliseconds, every minute it will be 500 milliseconds or more. A ping to a machine on the remote side of the vpn is usually 80 milliseconds and every minute or so it goes up to 2 seoconds for a few pings.

  If I take the vpn to the bottom of the judgment of the problem (i.e. ping the router/firewall to the intranet side is consistently below 1 millisecond)

  I discovered that these freezes/delays coincides with information in the vpn log file, it looks like this:

  2008-12-04 12:46:01 IKE[1] Set up ESP tunnel with 206.xxx.xxx.xx Success !2008-12-04 12:46:012008-12-04 12:46:34 IKE[1] Rx << QM_I1 : 206.xxx.xxx.xx HASH, SA, NONCE, ID, ID2008-12-04 12:46:34 IKE[1] **Check your Local/Remote Secure Group settings !2008-12-04 12:47:012008-12-04 12:47:01 IKE[1] Tx >> MM_I1 : 206.xxx.xxx.xx Error !2008-12-04 12:47:02 IKE[1] Rx << MM_R1 : 206.xxx.xxx.xx SA, VID2008-12-04 12:47:02 IKE[1] ISAKMP SA CKI=[342ed619 c59fed01] CKR=[kkkk1954 ffff4e87]2008-12-04 12:47:02 IKE[1] ISAKMP SA 3DES / MD5 / PreShared / MODP_1024 / 3600 sec (*3600 sec)2008-12-04 12:47:02 IKE[1] Tx >> MM_I2 : 206.xxx.xxx.xx KE, NONCE2008-12-04 12:47:03 IKE[1] Rx << MM_R2 : 206.xxx.xxx.xx KE, NONCE2008-12-04 12:47:03 IKE[1] Tx >> MM_I3 : 206.xxx.xxx.xx ID, HASH2008-12-04 12:47:05 IKE[1] Rx << MM_R3 : 206.xxx.xxx.xx ID, HASH2008-12-04 12:47:05 IKE[1] Rx << QM_R1 : 206.xxx.xxx.xx HASH, SA, NONCE, ID, ID2008-12-04 12:47:05 IKE[1] Tx >> QM_I2 : 206.xxx.xxx.xx HASH2008-12-04 12:47:05 IKE[1] ESP_SA 3DES / MD5 / 3600 sec / SPI=[nnnn7daf:mmmm9ee9]2008-12-04 12:47:05 IKE[1] Set up ESP tunnel with 206.xxx.xxx.xx Success !2008-12-04 12:47:052008-12-04 12:47:32 IKE[1] Rx << QM_I1 : 206.xxx.xxx.xx HASH, SA, NONCE, ID, ID2008-12-04 12:47:32 IKE[1] **Check your Local/Remote Secure Group settings !2008-12-04 12:48:012008-12-04 12:48:01 IKE[1] Tx >> MM_I1 : 206.xxx.xxx.xx Error !2008-12-04 12:48:02 IKE[1] Rx << MM_R1 : 206.xxx.xxx.xx SA, VID2008-12-04 12:48:02 IKE[1] ISAKMP SA CKI=[60e98e30 f5831f66] CKR=[kkkk6675 ffff38d1]2008-12-04 12:48:02 IKE[1] ISAKMP SA 3DES / MD5 / PreShared / MODP_1024 / 3600 sec (*3600 sec)2008-12-04 12:48:02 IKE[1] Tx >> MM_I2 : 206.xxx.xxx.xx KE, NONCE2008-12-04 12:48:03 IKE[1] Rx << MM_R2 : 206.xxx.xxx.xx KE, NONCE2008-12-04 12:48:03 IKE[1] Tx >> MM_I3 : 206.xxx.xxx.xx ID, HASH2008-12-04 12:48:05 IKE[1] Rx << MM_R3 : 206.xxx.xxx.xx ID, HASH2008-12-04 12:48:05 IKE[1] Rx << QM_R1 : 206.xxx.xxx.xx HASH, SA, NONCE, ID, ID2008-12-04 12:48:05 IKE[1] Tx >> QM_I2 : 206.xxx.xxx.xx HASH2008-12-04 12:48:05 IKE[1] ESP_SA 3DES / MD5 / 3600 sec / SPI=[nnnn65e5:mmmm2ea9]2008-12-04 12:48:05 IKE[1] Set up ESP tunnel with 206.xxx.xxx.xx Success !2008-12-04 12:48:05
  

  The situation described above repeats adfinium

  To be clear, the vpn works (with the exception of periodic delays) throughout several days

  I think that my settings may not completely right, butI don't know how to interpret the log above

  Found.

  I had disabled PFS. I enabled PFS and the problem disappeared.

  http://en.Wikipedia.org/wiki/Perfect_forward_secrecy

  See sections 8-10 http://www.ietf.org/rfc/rfc2409.txt to see why

• ASA VPN cannot ping ip local pool

  Hello

  We have ASA 5510 a device be deployed for a period of time. Everything works fine except customers local VPN cannot ping local customer VPN which get their IP address to the local swimming pool. They can ping anywhere on the local network of company, but not each other. I don't know there's a logical explantion for this because of an ACL but all appreciated the advice...

  Thanks in advance

  Keith

  Hi Keith,

  I think that, in order to allow a customer VPN reach another VPN client, the SAA should turn the VPN traffic (because it will receive the traffic of a VPN tunnel and re - again to send another tunnel.)

  Can you add "same-security-traffic intra-interface permits" and try again?

  Federico.

• The VPN Clients cannot Ping hosts

  I'll include a post my config. I have clients that connect through the VPN tunnel on the 180.0.0.0/24 network, 192.168.1.0/24 is the main network for the office.

  I can connect to the VPN, and I received a correct address assignment. I belive tunneling can be configured correctly in the aspect that I can always connect to the internet then on the VPN, but I can't ping all hosts on the 192.168.1.0 network. In the journal of the ASDM debugging, I see pings to the ASA, but no response is received on the client.

  6

  February 21, 2013

  21:54:26

  180.0.0.1

  53508

  192.168.1.1

  0

  Built of ICMP incoming connections for faddr gaddr laddr 192.168.1.1/0 (christopher) 192.168.1.1/0 180.0.0.1/53508

  Any help would be greatly appreciated, I'm currently presuring my CCNP so I would get a deeper understanding of how to resolve these issues.

  -Chris

  hostname RegencyRE - ASA

  domain regencyrealestate.info

  activate 2/VA7dRFkv6fjd1X of encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  name 180.0.0.0 Regency

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  link to the description of REGENCYSERVER

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  link to the description of RegencyRE-AP

  !

  interface Vlan1

  nameif inside

  security-level 100

  192.168.1.120 IP address 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.248

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS lookup field inside

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Server name 208.67.220.220

  name-server 208.67.222.222

  domain regencyrealestate.info

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 Regency 255.255.255.224

  RegencyRE_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0

  outside_access_in list extended access permit icmp any one

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  mask Regency 180.0.0.1 - 180.0.0.20 255.255.255.0 IP local pool

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ICMP allow all outside

  ASDM 255.255.255.0 inside Regency location

  ASDM location 192.168.0.0 255.255.0.0 inside

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 12.186.110.2 1

  Route inside 192.0.0.0 255.0.0.0 192.168.1.102 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  LOCAL AAA authentication serial console

  http server enable 8443

  http 0.0.0.0 0.0.0.0 outdoors

  http 0.0.0.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 15

  SSH version 2

  Console timeout 0

  dhcprelay Server 192.168.1.102 inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  NTP server 69.25.96.13 prefer external source

  NTP server 216.171.124.36 prefer external source

  WebVPN

  internal RegencyRE group strategy

  attributes of Group Policy RegencyRE

  value of server DNS 208.67.220.220 208.67.222.222

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list RegencyRE_splitTunnelAcl

  username password encrypted adriana privilege 0

  christopher encrypted privilege 15 password username

  irene encrypted password privilege 0 username

  type tunnel-group RegencyRE remote access

  attributes global-tunnel-group RegencyRE

  Regency address pool

  Group Policy - by default-RegencyRE

  IPSec-attributes tunnel-group RegencyRE

  pre-shared key R3 & eNcY1.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:35bc3a41701f7f8e9dde5fa35532896d

  : end

  Hello

  -be sure that the destination host 192.168.1.x has a route towards 180.0.0.0 by the ASA gateway.

  -Configure the following figure:

  capture capin interface inside match icmp 192.168.1.x host 180.0.0.x

  capture ASP asp type - drop all

  then make a continuous ping and get 'show capin cap' and 'asp cap.

  -then check the ping, the 'encrypted' counter is increasing in the VPN client statistics

  I would like to know about it, hope this helps

  ----

  Mashal

• Remote access VPN client to connect but cannot ping inside the host, after that split tunnel is activated (config-joint)

  Hello

  I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.

  is hell config please kindly and I would like to know what might happen.

  hostname horse

  domain evergreen.com

  activate 2KFQnbNIdI.2KYOU encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  ins-guard

  !

  interface GigabitEthernet0/0

  LAN description

  nameif inside

  security-level 100

  192.168.200.1 IP address 255.255.255.0

  !

  interface GigabitEthernet0/1

  Description CONNECTION_TO_FREEMAN

  nameif outside

  security-level 0

  IP 196.1.1.1 255.255.255.248

  !

  interface GigabitEthernet0/2

  Description CONNECTION_TO_TIGHTMAN

  nameif backup

  security-level 0

  IP 197.1.1.1 255.255.255.248

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  Shutdown

  No nameif

  no level of security

  no ip address

  management only

  !

  boot system Disk0: / asa844-1 - k8.bin

  boot system Disk0: / asa707 - k8.bin

  passive FTP mode

  clock timezone WAT 1

  DNS server-group DefaultDNS

  domain green.com

  network of the NETWORK_OBJ_192.168.2.0_25 object

  Subnet 192.168.2.0 255.255.255.128

  network of the NETWORK_OBJ_192.168.202.0_24 object

  192.168.202.0 subnet 255.255.255.0

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  the DM_INLINE_NETWORK_1 object-group network

  object-network 192.168.200.0 255.255.255.0

  object-network 192.168.202.0 255.255.255.0

  the DM_INLINE_NETWORK_2 object-group network

  object-network 192.168.200.0 255.255.255.0

  object-network 192.168.202.0 255.255.255.0

  access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any

  access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any

  Access extensive list permits all ip a OUTSIDE_IN

  gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

  standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0

  gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

  standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  backup of MTU 1500

  mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm-645 - 206.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  !

  network obj_any object

  dynamic NAT interface (inside, backup)

  Access-group interface inside INSIDE_OUT

  Access-group OUTSIDE_IN in interface outside

  Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10

  Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  Enable http server

  http 192.168.200.0 255.255.255.0 inside

  http 192.168.202.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  monitor SLA 100

  type echo protocol ipIcmpEcho 212.58.244.71 interface outside

  Timeout 3000

  frequency 5

  monitor als 100 calendar life never start-time now

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  backup of crypto backup_map interface card

  Crypto ikev1 allow outside

  Crypto ikev1 enable backup

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  !

  track 10 rtr 100 accessibility

  Telnet 192.168.200.0 255.255.255.0 inside

  Telnet 192.168.202.0 255.255.255.0 inside

  Telnet timeout 5

  SSH 192.168.202.0 255.255.255.0 inside

  SSH 192.168.200.0 255.255.255.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 15

  SSH group dh-Group1-sha1 key exchange

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntunnel strategy

  Group vpntunnel policy attributes

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntunnel_splitTunnelAcl

  field default value green.com

  internal vpntunnell group policy

  attributes of the strategy of group vpntunnell

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl

  field default value green.com

  Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password

  attributes of user name THE

  VPN-group-policy gbnlvpn

  tunnel-group vpntunnel type remote access

  tunnel-group vpntunnel General attributes

  address VPNPOOL pool

  strategy-group-by default vpntunnel

  tunnel-group vpntunnel ipsec-attributes

  IKEv1 pre-shared-key *.

  type tunnel-group vpntunnell remote access

  tunnel-group vpntunnell General-attributes

  address VPNPOOL2 pool

  Group Policy - by default-vpntunnell

  vpntunnell group of tunnel ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns migrated_dns_map_1

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the migrated_dns_map_1 dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565

  Hello

  1 - Please run these commands:

  "crypto isakmp nat-traversal 30.

  "crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.

  The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.

  Please let me know.

  Thank you.

• How to disable IMAQdx periodically sending a 'discovery' to 255.255.255.255 Ping?

  IMAQdx seems any GigE cameras by periodically (about every seconds) sending a Ping of 'discovery' to 255.255.255.255.
  As my vision system does not use any camera GigE (FireWire only) I would like to get rid of these "Pings of discovery."
  Is there a recommended way to achieve this?

  Best regards, Guenter

  Hi Guenter,

  Windows is not currently a way to disable the GigE Vision support in installer. However, you can disable the mechanism of Autodiscover with the following registry key:

  You should be able to save the following in a .reg file and then import it:

• AFTER VPN CONNECTED TO OFFICE VPN, PING TO A CERTAIN DESTINATION UNREACHABLE HOST BACK

  Hello!

  I have setup a connection to the vpn pptp from my home to my office.

  I've successfully connected to my office vpn.

  I can remote desktop to several server in my office, but there is that I can not remote to a pc desktop.

  When I try to ping it will return the destination unreachable host

  ping 192.168.9.50

  Impossible to reach the destination response 192.168.0.1 host

  it becomes instead of 192.168.9.50 192.168.0.1

  Can someone help with this problem?

  I really do work in this pc and I don't no how to connect there?

  I'm pretty remote desktop is allowed in this pc.

  Thank you

  GUKGUK

  The 192.168.0.1 address seems to be a gateway address.  VPN gateway may have no route to that particular system, either by design or due to oversight.  You should be facing this problem with your personal COMPUTER. Brian Tillman [MVP-Outlook]
  --------------------------------
  https://MVP.support.Microsoft.com/profile/Brian.Tillman
  If a response may help, please vote it as useful. If a response to the problem, please mark it as an answer.

• QuickVPN - could not do a ping the remote VPN router!

  Hello

  I have a RV042 (VPN router) and I have some problems to run properly using the QuickVPN client.

  Here is the Log of the QuickVPN client.

  2008-10-15 20:14:38 [STATUS] a network interface detected with 192.168.0.104 IP address
  2008-10-15 20:14:38 [STATUS] connection...
  2008-10-15 20:14:38 [STATUS] connection to a remote gateway with IP address: 96.20.174.84
  2008-10-15 20:14:38 [WARNING] server certificate does not exist on your local computer.
  2008-10-15 20:14:44 remote gateway [STATE] has been reached with https...
  2008-10-15 20:14:44 [STATUS] commissioning...
  2008-10-15 20:14:51 [STATUS] Tunnel is connected successfully.
  2008-10-15 20:14:51 [STATUS] verification of network...
  2008-10-15 20:14:55 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:14:58 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:01 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:05 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:08 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:11 [WARNING] Ping has been blocked, which can be caused by an unexpected disconnection.
  2008-10-15 20:15:19 [STATUS] disconnection...
  2008-10-15 20:15:25 [STATUS] Tunnel is disconnected successfully.

  I don't know how it is implemented, but if WuickVPN wait a form ping my router, it will not happen. I was never able to ping my router ouside of my ISP network.

  There is a way to disable the Ping process and continue with the VPN connection?

  QuickVPN try ping on the router via the VPN tunnel to check the connection. It should work without worrying about whether your ISP filters ICMP messages or not. The tunnel is encrypted your ISP won't know what you're doing.

  Please post the corresponding on the RV042 VPN log. That is expected to see how far you get.

  You have a firewall running on the computer? I think that some firewalls have difficulty with the traffic of ESP.

  What is the router that is connected to the computer? How is it that is configured?