Invalid scaling method

Similar Questions

• Thermocouple readings of the CRIO

  Hello

  I am fairly new to work with Compact RIO and I have problems with thermocouples that I have connected. My Setup has two modules of thermocouple in the NI 9213, NI 9211.

  I have connected a Type K thermocouple (one of each) both of the units. I used the vi FPGA target for reading from the Thermocouple channels as well as the CJC values and put two modules. I also CRIO vi which reference the FPGA vi, and then uses the values and feeds them to the "voltage convert to Temperature.vi. I've attached screenshots of the vi.

  The problem is the output I get is - 2 or 1 degree. When I touch the thermocouple increses value to about 5 or 8 degrees.  The room temperature is about 24 degrees.

  Can someone please help with where I'm wrong.

  concerning

  Bastien.

  Yes, it's the bad VI to be used with CompactRIO.  I'm not 100% sure why this does not work, but I don't know that the scaling VI that you use is designed to be used with NOR-DAQ, not CompactRIO.  Please open the examples for your modules to see the correct way to the scale of the CompactRIO thermocouple data.  I hope that these scaling methods will work for you.  You should find the examples here:

  C:\Program NIUninstaller Instruments\LabVIEW 8.6\examples\CompactRIO\Module Specific\

  This is the best advice I can give you, unfortunately.  If you need more detailed help, maybe someone on the forum knows more what to do about the scale of the data of thermocouples cRIO in degrees celsius.

• Scale object with Panel programmatically?

  Is there a way to activate the 'Object of scale with Panel' property of an object to front panel by programming?  It doesn't seem to be possible, but I wanted to check before you give up and do a hack to find a different solution.

  I think that the component "scaling" method will work for you.

• problem with qmlRegisterType

  Hi I have a problem with qmlRegister for the use of an onFarenheitChanged signal for my weather app, when I build and run, has no problem except that when the application starts, the accident with a message like this

  Process 2016309487 (WeatherNow) terminated SIGSEGV code=2 fltno=11 ip=7844f196(/base/usr/lib/qt4/lib/libQtDeclarative.so.4.8.5@_ZN36QDeclarativePropertyValueInterceptorC1Ev+0x711) mapaddr=0014f196. ref=07a4f2f8 bdslot=1
  

  and this is the code

  CPP

  WeatherNowApp::WeatherNowApp()
  {
      QCoreApplication::setOrganizationName("conias media");
      QCoreApplication::setApplicationName("WeatherNow");
  
       qmlRegisterUncreatableType("bb.device", 1, 0, "BatteryChargingState", "");
       qmlRegisterType("My.Library", 1, 0, "QTimer");
       qmlRegisterType("Network.ExternalIP", 1, 0, "ExternalIP");
       qmlRegisterType("Weather.Now", 1, 0, "WeatherNowApp");
       //! [0]
  

  HPP

  #ifndef WEATHERNOWAPP_HPP_
  #define WEATHERNOWAPP_HPP_
  
  #include 
  #include 
  using namespace bb::cascades;
  
  namespace bb
  {
      namespace cascades
      {
          class Application;
      }
  }
  
  class WeatherNowApp : public QObject {
      Q_OBJECT
  
      Q_PROPERTY(bool useFarenheit READ useFarenheit WRITE setUseFarenheit NOTIFY useFarenheitChanged)
  
  public:
  
      WeatherNowApp();
      Q_INVOKABLE void showPhotoInCard(const QString fileName);
  
  Q_SIGNALS:
      void useFarenheitChanged();
  

  and the qml

  import Weather.Now 1.0
  
  attachedObjects: [
  WeatherNowApp {
              onUseFarenheitChanged: {
  
              }
          }
  ]
  

  the qml missing changes to the label and that, but it does not even withouth code in there, so this isn't a problem on the internal code, suggestions?

  SIGSEGV error basically tells you that your application's RAM that does not belong to her or trying to run a class via an invalid pointer method.

  Do I have reason to assume that the WeatherNowApp class is the UI of your main application class? If Yes, I am confused why you would be save with QML, then by attaching to a page in QML. It is not normal to save the UI class main QML in the constructor of this class even with qmlRegisterType().

  I think that maybe what you really do is pass the instance of the main application to QML as a context property. If you try to respond to a signal of your main UI in QML class, then you should do so with the connect() function. Something like this instead:

  WeatherNowApp::WeatherNowApp()
  {
      QCoreApplication::setOrganizationName("conias media");
      QCoreApplication::setApplicationName("WeatherNow");
  
      qmlRegisterUncreatableType("bb.device", 1, 0, "BatteryChargingState", "");
      qmlRegisterType("My.Library", 1, 0, "QTimer");
      qmlRegisterType("Network.ExternalIP", 1, 0, "ExternalIP");
  
      QmlDocument *qml = QmlDocument::create( "asset:///main.qml" ).parent( this );
  
      // ---Make this app object available in QML
      qml->setContextProperty( "app", this );
  }
  

  Page {
     id: myPage
     function onUseFarenheitChanged() {
        if (_WeatherNow.useFarenheit == true)
           weatherDataTemperature.text = Math.round((jsonweather.temp)*1.8+32);
        else {
           weatherDataTemperature.text = Math.round(jsonweather.temp);
        }
     }
     onCreationCompleted: {
        app.useFarenheitChanged.connect(myPage.onUseFarenheitChanged);
     }
  }
  

  BTW, it makes no difference to the code, but you poorly spelled fahrenheit.

• What is SIP/2.0 481 call Leg/Transaction does not means?

  Hello

  When call cme of sip trunk and hang up the phone call calling debug ccsip show:

  Jun 2 08:52:40.541: //-1/xxxxxxxxxxxx/SIP/Info/ccsip_new_msg_preprocessor: invite dialog box control
  Jun 2 08:52:40.541: //-1/xxxxxxxxxxxx/SIP/Error/sipSPISipIncomingMsg: invalid (STATE_IDLE) method: CANCEL
  Jun 2 08:52:40.545: //-1/xxxxxxxxxxxx/SIP/Transport/sipSPISendErrorRespNoCCB: send error no. RCC response to the transport layer
  Jun 2 08:52:40.545: //-1/xxxxxxxxxxxx/SIP/Transport/sipSPITransportSendMessage: msg = 0x88D771A0, addr = 172.19.1.78, port = 5060, sentBy_port = 5060, is_req = 0, transport = 1, switch = 0, call = 0 x 00000000
  Jun 2 08:52:40.545: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnectionIfExists: support connection for addr = 172.19.1.78 not found
  CME(config-SIP-UA) #.
  Jun 2 08:52:40.545: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: display send msg = 0x88D771A0, addr = 172.19.1.78, port = 5060, connId = 0 for UDP
  Jun 2 08:52:40.553: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
  Envoy:
  SIP/2.0 481 call Leg/Transaction does not exist
  Via: SIP/2.0/UDP 77.72.169.134:5060; branch = z9hG4bK49b6543463d947caa1e4b81bf0267d24; received = 172.19.1.78
  From: <> [email protected] / * /: 5060 >; tag = 4e0113ac4c050c86452e9
  To: [email protected] / * / add: 5060 >
  Call ID: 4c4d940ab840442cb123a51a893cf5f5
  CSeq: 3 CANCEL
  Content-Length: 0

  Hello

  This means that the bridge is not no matter what record in the appeal. It was not any call or that it has removed the information.

  Looking at the extract, this particular msg was sent in response to cancel event. Without seeing the debug, I'm assuming that GW has previously received cancel and delete the call and send response. But on the side of appellant sent another msg so cancel gw gives above msg

  Hope this helps

  Thank you

  -abu

• Try to resize a bitmap - FASTJPEG: progressive decoding is not supported

  Hi all

  I went through the forums and tried many examples to remedy this, but none of them have worked.

  I download a .jpg file from a URL of site Web, internal to our society, to get a photo of the employee.

  I then use the code to resize the image to 100 x 100, no matter what the image is the size I need to resize to 100 x 100.

  The last code I tried is as follows:

  EncodedImage image = EncodedImage.createEncodedImage(imageBytes, 0, imageBytes.length); 
  
          int currentWidthFixed32 = Fixed32.toFP(image.getWidth());
          int currentHeightFixed32 = Fixed32.toFP(image.getHeight());
  
          int width = 100;
          int height = 100;
  
          int requiredWidthFixed32 = Fixed32.toFP(width);
          int requiredHeightFixed32 = Fixed32.toFP(height);
  
          int scaleXFixed32 = Fixed32.div(currentWidthFixed32, requiredWidthFixed32);
          int scaleYFixed32 = Fixed32.div(currentHeightFixed32, requiredHeightFixed32);
  
          image = image.scaleImage32(scaleXFixed32, scaleYFixed32);
  
          return image.getBitmap();
  

  However, it is not hidden image and gives me the following error:

  FASTJPEG: Progressive decoding is not supported

  It does not for all images, only some of them.  I discovered that the images in this case on images jpeg at 300 dpi, while those who work well is 96 dpi.  Is this the reason why?  Is there a way that these images can be resized properly, even if they are 300 dpi?

  I have not control how these images are saved in our society, I just have to get them via Http and resize them to display nicely on the Blackberry screen.

  Thanks for any help you can give.  I will continue to try other things as much as possible.

  Kind regards

  David

  If you work with OS 5.0 +, you can try the native Bitmap scaling methods provided.

• ORA-19030: invalid method for the schema not based XML Documents

  Hi everyone can u help me please when I am trying to execute query below his throw errror

  DECLARE

  doc xmltype.

  BEGIN

  SELECT

  XMLAGG (XMLElement ("employee",

  XMLAttributes)

                    ' http://www.Oracle.com/emp_simple.xsd ' AS 'xmlns',

                    ' http://www.w3.org/2001/XMLSchema-instance ' AS ' xmlns: xsi ",

                    ' http://www.Oracle.com/emp_simple.xsd

  http://www.oracle.com/emp_simple.xsd'

  AS "xsi: schemaLocation").

  XMLForest (e.employee_id LIKE "EmployeeId",

  Select AS "name."

  e.job_id AS "Job."

  e.manager_id "MANAGER."

  e.hire_date AS "Hire Date"

  e.Salary AS "wages."

  e.commission_pct AS 'The Commission',

  XMLForest)

  d.department_id AS "DeptNo."

  d.department_name AS "DeptName",.

  d.location_id AS 'Place') AS 'Dept')))

  in the doc

  E employees, departments d

  WHERE e.department_id = d.department_id;

  doc.schemaValidate ();

  END;

  /

  The error I get is following

  ORA-19030: invalid method for the schema not based XML Documents

  Yes, Odie meant something like that.

  See how the employee node can now occur more than once in the employees node.

• Code error: invalid line number 1 for class RowSet method GetRow PCPC:67

  People,
  
  Hello. I am writing PeopleCode to manipulate data in the scroll bar on level 1. My component has 4 pages and its Structure is as follows:
  
  Scroll - Level0
  JournalHeader
  JournalLine
  JournalTotal
  JournalError
  
  Scroll - Level1 primary JournalLine1 Record
  
  While JournalLine1 is inside the JournalLine page and its fields are 'Account' and 'amount '. The page 'JournalTotal' field is 'amount '. My job is to add up all the numbers in the field "Amount" of "JournalLine1" and assign the total amount for the field 'Amount' of the page 'JournalTotal '. My PeopleCode is as follows:
  
  
  All local & RS lines;
  Local Row row & total;
  Local Record & rec;
  Local Field & field;
  
  & RS = GetLevel0() (2). GetRowSet (Scroll.JournalLine1); / * JournalLine is on the 2nd level 0 * /.
  & line = & RS. GetRow (1); / * What a "JournalLine1" line on level 1 * /.
  
  For & I = 1 to & row. RecordCount
  & rec = & rank. GetRecord (& I);
  & field. Value = & on the ground. Value + & rec. GetField (Field.Amount). Value;
  -End;
  
  & total = GetLevel0() (3); / * JournalTotal is on the 3rd at level 0 * /.
  
  and total. GetRecord (Record.JournalTotal). GetField (Field.TotalAmount). Value = & on the ground. Value;
  
  
  
  The PeopleCode above is compiled. But when I run the component in the browser, I got this error:
  
  "Invalid line number 1 for the class method GetRow PCPC:67 RowSet. Component.GBL.JournalLine1.Amount.FieldChange. A PeopleCode program called an object method with an invalid value for the line number parameter. The line number must be in the range of lines present in all lines. »
  
  I think this error is called "& rank = & RS. GetRow (1); "Because there is only one line"JournalLine1"in level 1, it seems correct to use GetRow (1). I also tried ' GetRow (0) ' and ' GetRow (2) ", but got the same error.
  
  Why do '& rank = & RS. GetRow (1); "get such a mistake? People can help solve the problem?
  
  
  Thanks in advance.

  Try to make it simple;
  & total = 0;
  & RS_LEVEL0 = GetLevel0();
  & Row_LEVEL0 = & RS. GetRow (1);
  & RS_LEVEL1 = & Row .getrowset (Scroll.JournalLine1);
  For & I = 1 to & RS_LEVEL1. Activerowcount;
  & Row_LEVEL1 = & RS_LEVEL1. GetRow (&I);)
  & Record_LEVEL1 = & Row_LEVEL1. GetRecord (Record.JournalLine1);
  & Field_LEVEL1 = & Record_LEVEL1. GetField (Field.Amount);
  & Amount = & Field_LEVEL1. Value;
  & Total = Total & + &Amount;
  -end;

  Your_Level_0_Record_Name.LEVEL_0_TOTAL_FIELD_NAME. Value = &Total;

  I hope this will work!

  Do not no matter what declearation will be declared automaytically.

  Thank you
  Amit

• Presentation cfadmin login password, I get "invalid method (http verb) is used."

  It is of occurring after a new installation of IIS and the cfadmin Web site is configured via WSCONFIG. I followed all the recommendations of the authorization of user Pete CF11 Lockdown Guide, with the exception of the IIS configuration (still have not removed the maps and have not added to any URL deny sequences under request filtering). Which later I will because that's the goal.

  This is what I get after I submit my login and my password. the last http request that is made is to CFIDE/administrator/enter.cfm, which responds with 405.0 method not allowed (method not valid http verb)

  

  After that I can keep going back to the page of connection without problem. I can access the cfadmin on Internet Explorer logged on as an administrator of the server user (2012) web itself.

  Hello

  In order to test this simply add permission in the directory config of ColdFusion11. It is impossible to read the dll.

  Thank you

  Priyank

• No credit card error invalid when you try to change the method of billing (CC) for Adobe CC subscription

  It is not a problem of card or browser. I don't call the USA of Ros. What is the alternative?

  Hi daevemancreative,

  Please see the Ko: http://helpx.adobe.com/x-productkb/policy-pricing/membership-subscription-troubleshooting-creative-cloud.html and contact our conversation of support in the event of another problem.

  Kind regards

  Romit Sinha

• Invalid signature against the launch system officers

  I was searching through google and I had a number of tabs open throughout the day. Basically, I was looking for a way to get access to my product key for Microsoft Office on my Vista laptop as he conked suddenly me after a windows update to use a recovery disk, an old and reinstalled to factory settings and used the Mac for my search engine that I have been putting in place of the windows machine and then I noticed towards the end of the day than my search , it's on the Mac since I like to use it to do all the research, has been autocompleting.

  It was like a Cyrillic text over each letter that was typed in and then it would just broad head on its own. Whenever I tried a Cyrillic text page wouldn't be here since I drew a box around it for the screenshot.

  So I ran EtreCheck and here is the result:

  EtreCheck version: 2.9.12 (265)

  Report generated 2016-05-17 22:44:31

  Download EtreCheck from https://etrecheck.com

  Time 02:19

  Performance: Excellent

  Click the [Support] links to help with non-Apple products.

  Click [details] for more information on this line.

  Verify the signatures of Apple: enabled

  Problem: No problem - just check

  Hardware Information: ⓘ

  iMac (27-inch, late 2012)

  [Data sheet] - [User Guide] - [warranty & Service]

  iMac - model: iMac13, 2

  1 2.9 GHz Intel Core i5 CPU: 4 strands

  16 GB expandable RAM - [Instructions]

  BANK 0/DIMM0

  OK 4 GB DDR3 1600 MHz

  BANK 1/DIMM0

  OK 4 GB DDR3 1600 MHz

  0/DIMM1 BANK

  OK 4 GB DDR3 1600 MHz

  BANK 1/DIMM1

  OK 4 GB DDR3 1600 MHz

  Bluetooth: Good - transfer/Airdrop2 taken in charge

  Wireless: en1: 802.11 a/b/g/n

  Video information: ⓘ

  NVIDIA GeForce GTX 660M - VRAM: 512 MB

  iMac 2560 x 1440

  Software: ⓘ

  OS X El Capitan 10.11.5 (15F34) - since startup time: less than an hour

  Disc information: ⓘ

  ST1000DM003 disk HARD APPLE disk0: (1 TB) (rotation)

  EFI (disk0s1) < not mounted >: 210 MB

  Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB

  Macintosh HD (disk 1) /: 998,97 go-go (821,82 free)

  Encrypted AES - XTS unlocked

  Storage of carrots: disk0s2 999.35 GB Online

  USB information: ⓘ

  Apple Inc. FaceTime HD camera (built-in)

  Apple Inc. BRCM20702 hub.

  Apple Inc. Bluetooth USB host controller.

  Lightning information: ⓘ

  Apple Inc. Thunderbolt_bus.

  Configuration files: ⓘ

  /etc/sysctl.conf - file exists but not expected

  Guardian: ⓘ

  Mac App Store and identified developers

  Launch system officers: ⓘ

  [operation] com.apple.Finder.plist (2015-08-23) -invalid signature!

  [loading] com.apple.FollowUpUI.plist (2015-08-22) -invalid signature!

  [loading] com.apple.ScreenReaderUIServer.plist (2015-08-23) -invalid signature!

  [loading] com.apple.powerchime.plist (2015-08-22) -invalid signature!

  [loading] com.apple.quicklook.32bit.plist (2015-08-22) -invalid signature!

  [operation] com.apple.quicklook.plist (2015-08-22) -invalid signature!

  [loading] com.apple.quicklook.ui.helper.plist (2015-08-22) -invalid signature!

  [loaded] 6 tasks Apple

  [loading] 163 tasks Apple

  [operation] 69 tasks Apple

  Launch system demons: ⓘ

  [loaded] 45 tasks Apple

  [loading] 158 tasks Apple

  [operation] 88 tasks Apple

  Launch officers: ⓘ

  [loading] com.google.keystone.agent.plist (2016-03-03) [Support]

  [operation] com.intego.commonservices.integomenu.plist (2013-12-13) [Support]

  [loading] com.intego.commonservices.taskmanager.plist (2013-11-12) [Support]

  [loading] com.intego.commonservices.uninstaller.plist (2013-12-03) [Support]

  [operation] com.intego.netbarrier.alert.plist (2013-09-23) [Support]

  [operation] com.intego.netupdate.agent.plist (2015-06-29) [Support]

  [operation] com.intego.virusbarrier.alert.plist (2013-09-06) [Support]

  [loading] com.oracle.java.Java - Updater.plist (05 / 05/2013) [Support]

  Launch demons: ⓘ

  [loading] com.adobe.fpsaud.plist (2016-05-09) [Support]

  [loading] com.google.keystone.daemon.plist (2016-03-03) [Support]

  [operation] com.intego.commonservices.daemon.integod.plist (2013-11-12) [Support]

  [operation] com.intego.commonservices.daemon.taskmanager.plist (2013-11-12) [Support]

  [loading] com.intego.commonservices.icalserver.plist (2013-11-12) [Support]

  [loading] com.intego.commonservices.metrics.kschecker.plist (2013-11-12) [Support]

  [operation] com.intego.netbarrier.daemon.logger.plist (2013-09-23) [Support]

  [operation] com.intego.netbarrier.daemon.monitor.plist (2013-09-23) [Support]

  [operation] com.intego.netbarrier.daemon.plist (2013-09-23) [Support]

  [operation] com.intego.netupdate.daemon.plist (2015-06-29) [Support]

  [loading] com.intego.virusbarrier.daemon.emlparser.plist (2013-09-06) [Support]

  [operation] com.intego.virusbarrier.daemon.logger.plist (2013-09-06) [Support]

  [operation] com.intego.virusbarrier.daemon.plist (2013-09-06) [Support]

  [operation] com.intego.virusbarrier.daemon.scanner.plist (2013-09-06) [Support]

  [operation] com.objective - see.ransomwhere.plist (2016-04-20) [Support]

  [loading] com.oracle.java.Helper - Tool.plist (05 / 05/2013) [Support]

  Other applications: ⓘ

  [ongoing] com.apple.AmbientDisplayAgent

  com.apple.BKAgentService [loading]

  com.apple.MailServiceAgent [loading]

  [ongoing] com.dashlane.DashlaneAgent

  [ongoing] com.etresoft.EtreCheck.46112

  [ongoing] com.Intego.VirusBarrier.daemon.realtime

  [loading] 405 tasks Apple

  [operation] 185 tasks Apple

  Plug-ins Internet: ⓘ

  FlashPlayer - 10.6: 21.0.0.242 - SDK 10.6 (2016-05-12) [Support]

  QuickTime Plugin: 7.7.3 (2016-05-17)

  AdobePDFViewerNPAPI: 15.010.20056 - SDK 10.8 (2015-12-18) [Support]

  AdobePDFViewer: 15.010.20056 - SDK 10.8 (2015-12-18) [Support]

  Flash Player: 21.0.0.242 - SDK 10.6 (2016-05-12) [Support]

  Default browser: 601 - SDK 10.11 (2016-05-17)

  JavaAppletPlugin: Java 8 update 91 build 14 (2016-04-22) , check the version

  Safari extensions: ⓘ

  ClickToFlash - Marc Hoyois - http://hoyois.github.com/safariextensions/clicktoplugin/ (2015-11-12)

  ClickToPlugin - Marc Hoyois - http://hoyois.github.com/safariextensions/clicktoplugin/ (2016-05-14)

  Dashlane - Dashlane Inc. - http://www.dashlane.com (2016-05-02)

  3rd party preference panes: ⓘ

  Flash Player (2016-05-09) [Support]

  Java (2016-04-22) [Support]

  Spelling (2009-12-24), [Support]

  TeXDistPrefPane (2016-03-05) [Support]

  Time Machine: ⓘ

  Skip system files: No.

  Mobile backups: OFF

  Automatic backup: YES

  Volumes to back up:

  Macintosh HD: Disc size: 998,97 GB disc used: 177,15 GB

  Destinations:

  [Network] data

  Total size: TB 3.00

  Total number of backups: 192

  An older backup: 28/04/13, 09:27

  Last backup: 17/05/16, 21:48

  Size of backup drive: Excellent

  Size of backup 3.00 TB > (disk size 998,97 GB X 3)

  Top of page process CPU: ⓘ

  2% fontd

  mdworker (10) 2%

  2% WindowServer

  2% SDM

  1% kernel_task

  Top of page process of memory: ⓘ

  Kernel_task 996 MB

  213 MB virusbarriers

  180 MB mdworker (11)

  180 MB mds_stores

  Ocspd 66 MB

  Virtual memory information: ⓘ

  11.00 GB of free RAM

  4.97 GB used RAM (3.55 GB being cached)

  Used Swap 0 B

  Diagnostic information: ⓘ

  May 17, 2016, 22:39:23 self test - passed

  May 17, 2016, 07:57:45 AM/Library/Logs/DiagnosticReports/IDSKeychainSyncingProxy_2016-05-17-075745_ [reda DECT] .crash

  /System/Library/frameworks/security.Framework/versions/A/resources/IDSKeychainS yncingProxy.bundle/Contents/MacOS/IDSKeychainSyncingProxy

  I deleted the cookies, cache and browsing history and restarted three times now, but the report stays even if these agents of the system are still loading or running seven of them have signatures not valid.

  UH I installed OS X Capitan earlier today.

  Any ideas as to why these launch system officers have invalid signatures? I guess that specifically, should I worry?

  Hello TomsApple,

  I can't help much with the issue of the police. I suggest you to start a new thread and concentrate on this. For your EtreCheck report, you see these failures signature because you had turned on the verification of the Signature by Apple. I disabled as default because too many executable files from Apple did not comply with the verification of signature. I check all the executables you listed, but I can confirm that PowerChime now has an invalid signature in 10.11.5. I would not be surprised if this was true for the other institutions.

  For now, I suggest that the verification of the Signature off Apple - default setting. I plan on it the reactivation in the next version, but I want to catalog all known chess before. Unfortunately, malware authors have now begun to usurp the identity of Apple. The only reliable method to detect this is to verify the signature. But if Apple cannot guarantee that he signed all its executables or them correctly signed, so there is no way to know if Apple just updated an application or if you have been hacked. Apple seems based on the Protection of the integrity of system being unbreakable. That is regrettable.

• HP Envy 14 LR198AV: HP sold me PC with no valid Windows 7 or at least an invalid Windows product key and product ID

  I bought this PC in July 2011 and it is out of warranty.  After that of being harassed at level to Windows 10 months I decided to do it, but rather than the upgrade, I did a clean install from the laptop was malfunctioning.  I read on the Microsoft site that we could do it as long as they have Windows product key for Windows 7 Home Premium Service Pack 1 that was already installed on the machine.  I wrote that down with the Windows ID (different number).

  I've updated by downloading Windows 10 to a USB key and then the installation.  Seemed to work very well (I think that I entered my product in the process ID).  Now, a few weeks later I get a message that I need to "activate windows".  I called MIcrosoft after it could not activate using the ID that I and after 30 minutes on the phone they me said my Windows product ID and both are my "invalid" Windows product key  I would call HP and get this sorted - I have the original order number and Microsoft said that's all I need for HP to help me - but I am out of warranty and apparently help me unless I pay them $60.  Another alternative is to buy a new copy of Windows 10 and pay MIcrosoft money.

  I am shocked, because I'm simply doing what Microsoft has been harassment to me.

  BTW, the PC seems to work fine except the message to activate windows.  I guess that another option is to do nothing.

  Any suggestions will be appreciated.

  Thank you.

  Available for the free upgrade until the end of July 2016, according to the latest rules from Microsoft Windows 10. Thus, you will be able to spend to Win 10 If you want. I'm not a fan of win 10, but if you want to upgrade to it I personally recommend the ISO for Win 7 upgrade method to win 10-

  # Download the ISO from MS site, burn it to a DVD, insert the DVD into the PC and start the process from inside Windows 7

  # Follow the on-screen instructions then

• Motherboard model H535 failure - the type of machine and the serial number invalid after replacement

  Does anyone know how to set the new Type of Machine and the serial number after a motherboard for a replacement model H535?

  The motherboard has recently failed on my model H535 (7 months after the expiration of the warranty - thanks, Lenovo). No local garage would agree to replace due to its nature of owners (thanks, Lenovo). I spent about four hours on the phone being bounced into back-and-forth between the many support staff (usually combined) Lenovo in sales, technical support, support of parts of IBM and various other departments (thanks, Lenovo), which one has suggested that I might have to try to find a motherboard on Ebay or Amazon for my computer in less-than-2-year-old. However, I finally get to someone at Lenovo, which has been able to sell a motherboard - for 2/3 of the cost of the original computer.

  Now, I installed the motherboard, and it works. However, during each boot, I get a POST with two beeps error which reads as follows:

  00CE error: Machine Type and serial number is INVALID

  Start of manufacturing sequence is taken if no selection is made

  I presume that the BIOS on the new motherboard must be programmed with the right Type of Machine and the serial number of my computer. I've read various things on the Internet about what to do, as updating the BIOS (I can not even find a BIOS under "downloads" of support for the H535 - thanks, Lenovo model), using WinPhlash (I apparently need one kind of BIOS ROM file to make it work, I don't have), getting a Lenovo hardware maintenance disk for my model (which apparently isn't available for other special people only me - thanks Lenovo), etc.

  The waiting time for Lenovo support are ridiculously long, and almost every customer support person is ridiculously uninformed on the difference between one of their computer models, and even less their motherboards (thanks, Lenovo). I am amazed and extremely frustrated. It shouldn't be rocket science.

  On a side note, I initially bought the computer from Staples with a credit card with extended warranty protection, which means I can get a refund for repair. Although the motherboard came with a packing list, no Bill has been provided by Lenovo, and I couldn't make them send one - or maybe even with success to explain what a Bill is (thanks, Lenovo).

  Well, Lenovo support was useless, and any alleged authorized suppliers were in fact still suppliers or could help with my problem. But I was finally able to fix it myself. Once I found the right piece of software, it has been fixed in less than a minute.

  My BIOS is by American Megatrends, and I discovered that they have a set of utilities that includes a called AMIDEDOS. It is intended for manufacturers to be able to change the strings of text stored in the BIOS for things like the manufacturer, product name, Version, number series, UUID, SKU number, family, etc., that is what I had to do. It is not intended for use by consumers, but it's there.

  When I ran the "DMIEdit.exe" program AMIDEDOS (clicked and ran as administrator from 10 Windows) and click on "System information" from the list, I saw "Product Name | STRING | Invalid' and ' serial number | STRING | NOT VALID ". The other fields appeared to have valid entries. I double-clicked on the fields valid and changed their "H535 model" and the serial number of my computer, respectively and then clicked on "Update all" at the top.

  Much to my surprise, he reported that he had successfully registered the new information. And, perhaps even more surprising is the fact that, when I rebooted, the double beep and the warning about the type of computer not valid and serial number have disappeared. In addition, the BIOS showed I had entered the new values, and the 'Manufacturing Boot Sequence' option (I understand can be much slower than a normal boot) had disappeared.

  Again, I'm a little surprised simple it was actually solve the problem once I got the correct software, or Lenovo part nor American Megatrends apparently offers to the owners, and it took hours and hours of research and research to understand. Use this information at your own risk, however, as playing with BIOS apparently can lead to problems not easily solved. That said, the modification of these text strings seems relatively safe.

  I will mention that I also ended up changing the method of "LEGACY" to "UEFI" boot in the BIOS after noticing that the selection.

• 6008 analog input - invalid values

  Hello

  Does anyone know how the analog input voltage 6008 invalid handles?  Specifically, what happens if the circumstantial channel is configured for a 0 - 10 range v and a voltage negaitve, (-19.0) volts is placed on the analog input?

  I use the library, C/C++, OR-DAQMx library.  The call that I use to set up the port of AtoD is:

  DAQmxErrChk (DAQmxCreateAIVoltageChan (taskHandle, AINPSTR, "", DAQmx_Val_Diff, 0,0, (float64) s_dMaxAnalogInputVoltage, DAQmx_Val_Volts, ""));

  where: s_dMaxAnalogInputVoltage = 10.0;

  and

  DAQmxReadAnalogF64 (taskHandle, 1, 1.0, DAQmx_Val_GroupByChannel, values, 5, & not read, NULL);

  to read the circumstantial.

  What will happen if any illegal input voltage is applied.  I know that everything is a wide range, so I don't talk about something like -60 to + 60 volts.

  Thank you

  -Neil shore

  These specifications are in the datasheet of the product - link to it in the product specifications of the page tab.

  And no, there is no error generated when the input is out of reach.  Scaling the proper entry so that this doesn't happen. or if this is the case, your software recognizes that is higher than expected.

• reference not valid error 1026 to the runVI call the hand method exe-&gt; slot - VI-&gt; secondary

  Hello

  I have a main VI who Subvi inside case structures put in place to show FP when called and be modal.

  These subVIs have a secondary that will pull up a call using RunVI method dynamicVI. The dymaicVIs is built using the constant application directory + name of VI to the invoke method.

  now the main VI is built in exe with the dynamicVIs in the list always included.

  When I run the main exe I get error 1026 VI reference invalid.

  Help, please

  Thank you

  Choose the layout of the 8.X file will change the path that your screw referenced are when you build your executable file.

  http://zone.NI.com/reference/en-XX/help/371361K-01/lvconcepts/referencing_files_in_applications/

  If you choose this option of layout, you adress just the vi you are calling where having the option deselected will mimic your file structure layout it is developing.