IPMI over LAN

Similar Questions

• iDRAC on Dell R610 problem

  Hello

  I just got a new Dell R610 and I tried to configure the iDRAC on her card. I have it configured on interfaces of multiple T300 Dell and the ILO on the different models of HP servers successfully. But for some reason, I'm going to have serious problems with it.

  I think he got an iDRAC Express card as there is no extra ethernet port on the server, just the standard 4 integrated NETWORK interface the iDRAC BIOS are version 1.70 I understand is the last.

  In the screen configuration (Ctrl + E) iDRAC, iDRAC and IPMI over LAN are enabled. Selection of NIC is set to shared so for active LOM, it reports 'No. Active LOM'. VLANs are disabled, iDRAC Express stand them? -Once it works I would like to enable it if possible.

  Only NIC1 (eth0) is connected to the switch. I tried configuring it with DHCP, but he never does an address even if the operating system gets a.

  To remove the switch / VLAN even tried to connect NIC1 directly on an other server tcpdump and running with iDRAC configured with a static IP (the default value of 192.168.0.120). Did not get a thing of it. I could see the arp requests going out but not responses to iDRAC.

  So, how do you get the iDRAC to work?

  Thank you.

  Today technician Dell replaced our motherboard and this fixed a problem with the DRAC.

  New motherboard uses older versions of BIOS and DRAC BIOS main:

  principal: was 3.0.0, now for 2.0.11
  DRAC: was 1.70.21, now 1.41.13

  DRAC works now, and, Yes, she has the web interface.

  PS unfortunately, but this will not be fixed another issue we have with H200 controller or it's linux driver mpt2sas: https://bugs.launchpad.net/linux/+bug/777441 (ClxAdmin, if you use Linux on that server, what distribution of linux/version you are using?)

• Remote access suitable for BMC on PE T110II

  Hello

  I have a question. We have a T110II EP with only available for Remote Mgmt BMC.  What would be the good way/tool to access the BMC to restart the PowerEdge server for example remotely?

  I know that BMC and the share of the NIC system.  In the screenshot I joined, the system seems to complain about the shared NIC...  (not sure if properly configured)

  Thank you

  : o).

  Hello

  This wiki article has instructions on the use of the IPMI remote commands. I've skimmed the article and didn't see any reference to enable IPMI over LAN. Some of our CR/iDRAC require IPMI over LAN is enabled in order to use IPMI on a GROUND connection, you may need to allow that as well.

  http://de.community.Dell.com/TechCenter/systems-management/w/wiki/485.IPMI-uber-bmc-MIT-PowerEdge-server-nutzen-Englisch

  CMechtilde

  I know that BMC and the share of the NIC system.  In the screenshot I joined, the system seems to complain about the shared NIC...  (not sure if properly configured)

  This isn't an error message. It's just a warning message. If you have shared active NIC you should have no interface shared as a member of a team of network or LAG.

  Thank you

• BMC is not detected.

  Hi all. I have a PowerEdge R200 server with bmc, but I can't connect to the bmc over LAN. I set up a network through ipmitool.

  ipmitool lan print 1
  Current value: complete Set
  AUTH Type Support: MD5, MD2 NO PASSWORD
  AUTH Type Enable: Reminder: MD2, MD5
  : User: MD5, MD2
  : Operator: MD2, MD5
  : Admin: MD2, MD5
  : OEM: MD2, MD5
  Source IP address: static address
  IP address: 192.168.162.75
  Subnet mask: 255.255.255.0
  MAC address: a4:ba:db:df:9 c: 6th
  SNMP community string: public
  IP header: TTL = 0 x 40 flags priority = 0x40 = 0x00 TOS = 0 x 10
  Default IP gateway: 192.168.162.254
  MAC default gateway: 00:00:00:00:00:00
  Backup gateway IP: 0.0.0.0
  MAC backup gateway: 00:00:00:00:00:00
  802 1 q VLAN ID: disabled
  802 1 q VLAN Priority: 0
  Cipher Suite private Max: not available

  IPMI Version: 1.5

  Firmware revision: 1.83

  I can't ping, but there in the ARP table.

  ARP - a
  ? (192.168.162.75) to a4:ba:db:df:9 c: 6th [ether] on em1
  ? (192.168.162.74) to a4:ba:db:df:a1:51 [ether] on em1
  ? (192.168.162.84) to d4:ae:52:64:a2:24 [ether] on em1

  I tried to connect to the port via netcat 623

  NC - uv 192.168.162.75 623
  Connection to 192.168.162.75 port 623 [udp/asf-rmcp] was successful!

  When try to connect, I get an error

  IPMISH > connect ip - 192.168.162.75 u root Pei admin
  (0xae) error: error BMC - BMC is not accessible.
  IPMISH >

  You have an idea, which would solve this problem?

  Hello

  In the BIOS system under devices integrated Serial Port 1 is on? When you start to CTL E is IPMI over LAN active?

  Thank you

• WOI for Poweredge 1950

  I have a rack with several different generations of Poweredge 1950 servers and a few R610s.  I would like to distance the departure (WOI), stop and use the systems in the basket.  Systems do not have the DRAC cards installed.

  I WOL installation for all systems and can start and stop all on the local network very well.  If I can start a unique system of p1950 remotely, then I can easily start and stop all the systems using this unique system.

  But I can't do simple p1950 system to remote start.  I put the Port Forwarding on my router/modem DSL to transfer 9 UDP to the system and sees the magic packet very well... but it will not turn on.

  I am familiar with the planks of the DRAC and the various management tools remotely, but reading that I did... it seems possible to be able to power and turn off the machine to the Internet.

  Please can someone explain what I need to be able to remotely turn on the system?

  I can do without a DRAC card installed?

  This software is required to send to connect with the system and send the signal from power?

  Thank you!

  You can use the ipmitool to turn on and turn off the server. For this you require not DRAC. You must follow the steps below to configure this

  1. Configure the IP address and compatible IPMI over LAN to iDRAC or BMC.
     1. R610 will have default iDRAC. For more details see section "Using the iDRAC6 Configuration utility" on iDRAC user's Guide. You can download the iDRAC from here user guide

        FTP://FTP.Dell.com/manuals/all-products/esuprt_electronics/esuprt_software/esuprt_remote_ent_sys_mgmt/integrated-Dell-remote-access-cntrllr-6-for-monolithic-Srvr-v1.95_User%27s%20Guide_en-us.PDF

     2. 1950, you need to configure BMC. You can configure the IP address and IPMI over LAN at similar to R610 boot
  2. Install ipmitool on a client computer. You can download ipmitool from here
  3. Run the following command to power on the server

  ipmitool - I lanplus h u Pei power on

  Run following command to get help on this command

  ipmitool - I lanplus h u Pei power

• Dell PowerEdge 2950 of installation

  I'm testing DPM on a Dell PowerEdge 2950.  To make this work, I have need to configure IPMI if I can have a server go to safe mode and out of safe mode.  I've been Googling like crazy, but have been unable to find an answer on how to get this working.  Whenever I try to put my host in standby I get this message:

  vCenter has determined that it cannot resume host & lt; hostname & gt; standby; Therefore, the eve of the entry task was suspended.
  Confirm that IPMI/ILO is configured correctly for host & lt; hostname & gt;.  Or, configure vCenter to use WoL, making sure there are at least two or more hosts in the cluster, and then try the task again.

  A couple of things about this error: an it is a cluster two host (for testing purposes).  Two, I use Dell hardware so I have to use IPMI not ILO.

  I have connected my DRAC page and enabled IPMI over LAN, but I don't know what else to do here, and I don't know where all the parameters concerning this in vCenter or ESX.  Any help would be appreciated.

  Gunnar

  I used the setting of Dell OpenManage.

  Under system / main system / remote access, you can see:

  Select the IPMI Over LAN-> Yes (don't forget it is YES)

  SOIL active Yes

  XXXXXXXXXX MAC address

  IPv4 address

  IP address static Source

  YYYYY IP address

  In ESX, under Configuration / PowerManagement / properties I use:

  BMC IP: YYYYY

  BMC MAC: XXXXX

  André

• Check the consistency of the regular Raid

  Is it possible to put in place a regular Raid consistency check to say occur every weekend?  We have a T420 with a 310 Perc controller.

  Hello Nick

  I'm not aware of an option in one of our applications to automate the consistency checks. I can think of do the simplest is to use a script and a task scheduler in the host operating system. I don't know that you can script to a remote system via IPMI over LAN as well.

  For this you need the RACADM capacity, so you would need to install something like node to manage OpenManage Server administrator on the system, you run the commands from. Then, create a batch file. See page 154 of the guide of the user of the OMSA for the syntax:

  User Guide

  omconfig storage vdisk action = checkconsistency = 0 = 0 vdisk controller
  omconfig storage vdisk action = checkconsistency = 0 = 1 vdisk controller
  omconfig storage vdisk = checkconsistency controller action = 0 vdisk = 2

  You can use omreport about what your controller and virtual disk ID are. If you have multiple virtual disks, then you can have multiple orders in the same batch as my above command file. You don't need to put anything else in the orders except the omconfig command file. Put just the Task Scheduler to open the batch file when you want than to start consistency checks.

  Thank you

• HOWTO specify the zone on UCS C220 M3 by CLI

  Hello, I have configured NTP in the GUI, but bad weather due to a time zone is not OK

  I can't change the time zone in the GUI, so I looked for some CLI commands.

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/SW/CLI/config/Guide/1-3-1/b_CLI_Config_Guide_1_3_1/CLI_Config_Guide_1_3_1_chapter33.html#task_A14B792FD20A458E8990E93368F5B222

  According to this article, it should be possible to use the system to scope, but this command is not available in my CLI:

  BKS-C220-FCH1743V1FY #.
  commit the changes to batch validation
  connect to Connect to another console
  discard discard all changes
  out of the shell
  scope changes the current mode
  set property values Set
  view the system information see the
  top of the page to go to higher mode

  BKS-C220-FCH1743V1FY #.
  BKS-C220-scope FCH1743V1FY #.
  BIOS system BIOS: Basic Input/Output System
  certificate of security for SSH & SSL certificates
  Chassis server items in stock
  MMIC Cisco Integrated Management Controller
  Configuration of alerts on the platform event/fault fault
  Protocol http Hyper Text Transfer Protocol
  IPMI Intelligent Platform Management Interface
  console keyboard video mouse KVM to host
  LDAP Lightweight Directory Access Protocol
  salt of the system event log
  sensor sensors
  SNMP Simple Network Management Protocol
  ground Serial Over Lan (console character of host mode)
  SSH Secure Shell Configuration
  local users of the user of this CIMC
  sessions active user of user on this MMIC session
  VMedia Virtual Media (local media on the host mount)
  xmlapi Configuration API XML

  BKS-C220-scope FCH1743V1FY #.
  % Incomplete command
  BKS-C220-FCH1743V1FY #.

  How should I change the time zone?

  Hello

  Unfortunately you have checked a guide old enough to UCSM 1.3 (we went through UCSM 1.4/2.0/2.1 and currently on 2.2 already), and that server you are trying to set up seems to be offline...

  For a stand-alone server of series C, only 2 how time management is in the BIOS or Setup NTP (counting 1.5 MMIC) but not their time zone.  See the screenshots attached.

  If you join the server with UCSM then you can configure the time zone.

  -Note ALL useful answers

  -Kenny

• HP Z420: Other devices (missing drivers)

  Hello world

  For the life of me, there are two devices in Device Manager that I can't seem to update:

  PCI serial port
  SAS controller

  In both devices, this is the last 2 timestamp description which is noted:

  PCI serial port

  1)

  Device PCI VEN_8086 & DEV_1D3D & SUBSYS_1589103C & REV_05\3 & 11583659 & 0 & B3 requires installation.

  2)

  Device PCI VEN_8086 & DEV_1D3D & SUBSYS_1589103C & REV_05\3 & 11583659 & 0 & B3 has been configured.

  Driver name: null
  The class GUID: {00000000-0000-0000-0000-000000000000}
  Driver date:
  Driver version:
  Driver provider:
  Section of the driver:
  Rank of pilot: 0x0
  Matching device ID:
  Advanced driver:
  Update of the device: false
  Device of parents: ACPI\PNP0A08\0

  I think it's the guest card Vantec PCIe RAID (UGT-ST644R).  I installed the drivers from Win10... but it does not go away.

  SAS controller

  1)

  Device PCI VEN_8086 & DEV_1D6B & SUBSYS_1589103C & REV_05\4 & a95f37b & 0 & 0088 has been configured.

  2)

  Driver name: null
  The class GUID: {00000000-0000-0000-0000-000000000000}
  Driver date:
  Driver version:
  Driver provider:
  Section of the driver:
  Rank of pilot: 0x0
  Matching device ID:
  Advanced driver:
  Update of the device: false
  Parent device: PCI\VEN_8086 & DEV_1D3E & SUBSYS_1589103C & REV_05\3 & 11583659 & 0 & 88

  Device PCI VEN_8086 & DEV_1D6B & SUBSYS_1589103C & REV_05\4 & a95f37b & 0 & 0088 requires installation.

  I don't know what helps me to do now... Any suggestions on how to solve this problem would be fantastic!

  See you soon,.
  -Richard

  Hi, Richard:

  The PCI Serial Port device needs this driver...

  This package contains version Intel Management Engine Software 11.0 for desktop models and operating systems supported. This package installs the latest drivers Management Engine Interface (MEI) and Serial-Over-LAN (GROUND), as well as the Intel Management and security status (IMSS), to support versions Intel Active Management Technology (AMT) 8.x and 9.x.

  FTP://ftp.HP.com/pub/SoftPaq/sp74001-74500/sp74499.exe

  Try to install the driver manually if automatic installation method does not work.

  Here's a partial copy and paste of the driver installation information file that shows the support of the drivers for the hardware ID you have posted.

  [Intel.NTamd64]
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1E3D & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1CBD & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1C3D & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1DBD & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1D3D & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_8C3D & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_9C3D & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_9CBD & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_8D3D & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_9D3D & CC_0700.
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_A13D & CC_0700.

  The 2nd device is a controller SAS of Intel and needs this driver...

  This package contains the Intel Rapid Storage Technology Enterprise (rest) drivers and the graphical user Interface (GUI) for controllers serial ATA (SATA) RAID in the models of desktop taken in charge who run a system of Microsoft Windows supported OS.

  FTP://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72212.exe

  Again, try to install the driver manually if auto installation does not work.

  Here's a partial copy and paste of the driver installation information file that shows support for the ID you have posted.

  % Intel_SAS_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D60 & CC_0107%
  % Intel_SATA_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D61 & CC_0107%
  % Intel_SAS_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D62 & CC_0107%
  % Intel_SAS_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D63 & CC_0107%
  % Intel_SAS_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D64 & CC_0107%
  % Intel_SAS_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D65 & CC_0107%
  % Intel_SAS_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D66 & CC_0107%
  % Intel_SAS_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D67 & CC_0107%
  % Intel_SAS_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D68 & CC_0107%
  % Intel_SAS_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D69 & CC_0107%
  % Intel_SATA_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D6A & CC_0107%
  % Intel_SATA_RAID. DESC = Intel_SCU_iaStorS_Inst, PCI VEN_8086 & DEV_1D6B & CC_0107%
  ;

• HP Compaq 6000 Pro AT492AV: Serial Port PCI Driver help - HP 6000 AT492AV Windows XP Pro

  Due to former software compatibility issues, I run Win XP on my computer HP Compaq 6000 Pro AT492AV.  I installed a new copy of XP OEM and have solved all driver except for 2 problems:

  (1) PCI Serial Port, here's the info from Device Manager:

  PCI serial port

  PCI bus 0, device 3, function 3

  PCI\VEN_8086 & DEV_2E17 & SUBSYS_3048103C & REV_03
  PCI\VEN_8086 & DEV_2E17 & SUBSYS_3048103C
  PCI\VEN_8086 & DEV_2E17 & CC_070002
  PCI\VEN_8086 & DEV_2E17 & CC_0700

  (2) unknown Device, here's the info from Device Manager:

  Controller of Interface LPC Intel(r) ICH10D - 3A1A

  ACPI\IFX0102
  * IFX0102

  I'd appreciate any help you can provide!

  All the best

  Hello:

  You need these drivers for devices...

  1.

  This package contains the Intel Local Management Service (LMS) and the support of Serial - over - LAN (SOL) for Intel Active Management Technology (AMT) for the supported desktop models and operating systems. This software is part of the Intel Digital Office Initiative.

  FTP://ftp.HP.com/pub/SoftPaq/sp45001-45500/sp45367.exe

  2.

  This package provides the device driver for the Infineon Trusted Platform
  Module (TPM 1.2) in office supported running models taken Microsoft support
  Windows XP operating system.
  
  FTP://ftp.HP.com/pub/SoftPaq/sp40501-41000/sp40553.exe

• dc7800p Convertible Minitowers: win 10 PCI Serial Port & PCI device drivers unknown misiing

  Have missing drivers - managed to solve PCI Simple Communication Device driver missing by downloading some drivers of HP support and running these '(Admin) command prompt' with them running in Win 7 Compatibility Mode.  What (s) that I have to run to remedy or if not where should I look to fix.

  Hello:

  You need this driver for the Serial Port PCI...

  This package contains the Intel Local Management Service (LMS) and the support of Serial - over - LAN (SOL) for Intel Active Management Technology (AMT) for the supported desktop models and operating systems. This software is part of the Intel Digital Office Initiative.

  FTP://ftp.HP.com/pub/SoftPaq/sp46001-46500/sp46134.exe

  Please post the hardware ID of the PCI device unknown that you are missing the driver.

  To find the hardware ID, go to the Device Manager and click on the unknown device needing driver.

  Then click on the Details tab in the upper part of the device window.

  Now you will see a drop-down list of property, and it will be set to the Description of the unit.

  On this list and select the 3rd point (Hardware ID).

  After the first string of characters you see in the window.

• dc7900 KP719AV: drivers PCI Mising

  HP Compaq dc 7900 Convertible Minitowers

  Win Xp SP3 x 86

  After a new installation on the new drive HARD can't find the drivers for the below

  Device ID

  PCI\VEN_8086 & DEV_2E17 & SUBSYS_3035103C & REV_03\3 & B1BFB68 & 0 & 1 b
  PCI\VEN_8086 & DEV_2E14 & SUBSYS_3035103C & REV_03\3 & B1BFB68 & 0 & 18
  ACPI\IFX0102\1

  Concerning

  You are the very welcome.

  I checked the file of the driver of the dc7900 support page, and I am not in favour of the hardware ID you have posted.

  This is why it did not work.

  The HP Elite 8000 uses the same chipset as the dc7900 (basically, it's the next model with DDR3 memory and a different audio chip).

  The file from this PC has support for the ID you have posted, so this should work.

  This package contains the Intel Local Management Service (LMS) and the support of Serial - over - LAN (SOL) for Intel Active Management Technology (AMT) for the supported desktop models and operating systems. This software is part of the Intel Digital Office Initiative.

  FTP://ftp.HP.com/pub/SoftPaq/sp45001-45500/sp45367.exe

• Compaq 8000 Elite COnvertible: compaq 8000 elite minitour convertible pci driver windows 7

  Hello, I had trouble finding the right drivers for my port of compaq 8000 elite series minitour convertible pci and pci simple communication controller, running windows 7 ultimate 64-bit...

  I found a link in a different thread, but the link does not work...

  Could someone help me please? It would be greatly appreciated☻

  Kind regards

  David

  Hello:

  You need these drivers for devices...

  Simple Comms:

  This package contains the device driver Intel Active Client Manager Host Embedded Controller Interface (HECI) for desktop models and operating systems supported.

  FTP://ftp.HP.com/pub/SoftPaq/sp45001-45500/sp45411.exe

  Serial port:

  This package contains the Intel Local Management Service (LMS) and the support of Serial - over - LAN (SOL) for Intel Active Management Technology (AMT) for the supported desktop models and operating systems. This software is part of the Intel Digital Office Initiative.

  FTP://ftp.HP.com/pub/SoftPaq/sp45001-45500/sp45367.exe

• Compaq 8000 Elite: Driver missing: PCI\VEN_8086 & DEV_2E17 & SUBSYS_3648103C & REV_03 for windows Compaq 8000 Elite 10

  HP dear community,

  Been Searchin' the WWW for ages now.

  I installed Windows 10 on this PC and the following driver keeps bugging me:

  PCI serial port

  PCI\VEN_8086 & DEV_2E17 & SUBSYS_3648103C & REV_03

  I triend Intel Driver Update Utility, which breaks down, I tried the GROUND driver and the driver of the AMT. Alll of them fail or are already installed.

  Please help me with this driver.

  Thank you in advance,

  FSolleveld.

  Kind regards
  
  Frank Solleveld.

  Hello:

  You need the driver for this device...

  This package contains the Intel Local Management Service (LMS) and the support of Serial - over - LAN (SOL) for Intel Active Management Technology (AMT) for the supported desktop models and operating systems. This software is part of the Intel Digital Office Initiative.

  File name: sp45367.exe

• HP DC7700: Serial Port PCI and simple Communication controllers pilots missing in HP DC7700 windows 7 (32 bit)

  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2997 & CC_070002
  PCI\VEN_8086 & DEV_2997 & CC_0700

  and

  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2994 & CC_078000
  PCI\VEN_8086 & DEV_2994 & CC_0780

  Experts in the House should please come to my rescue.

  I just upgraded my Hp DC7700. I was able to get all the drivers except for SERIAL PORT PCI and PCI SIMPLE COMMUNICATIONS CONTROLLER missing. above are the two missing pilots hardware ID

  Hello:

  There is no W7 drivers for these devices.  You must use the Vista drivers and if auto installation does not work, you will need to install the drivers manually by navigating to the folder of the driver that was created when you ran the file from the device in the Device Manager (browse my computer for driver software).

  This package contains the driver Intel Host Embedded Controller Interface (HECI) for access to Active Management Technology (AMT) initiative of the Intel Digital Office for rated desktop models and operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34743.exe

  This package contains the Intel (LMS) Local Management Service and Serial - over - LAN (SOL) support for the technology of Directors Active (AMT) under the Initiative of digital office Intel for the supported desktop models and
  operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34744.exe