IPsec site2sitevpn and DMVPN on a single WAN port

Similar Questions

• iTunes does not recognize my iPod or my iPhone. And nothing worked I tried. I have the latest version of everything. I uninstalled and reinstalled my iTunes. I restarted my iPod and phone and your PC severally. And I tried every single USB ports.

  Yesterday I gor the latest version of iTunes, but it does not recognize my iPhone or iPod. So I put them both to the latest iOS update. He still does not recognize my device. I upgraded Windows 10 because that's what one of the websites I visited told me to do. But it is still worse. Now my PC says that it does not recognize the USB when I plug my iPhone or iPod, but something always pops up asking what I want to do with my camera. I have uninstalled and reinstalled iTunes and even my Apple device Service. I tried practically everything that is currently on the Internet. I just don't understand. Please help me.

  Try the following:

  1. Open Control Panel > Device Manager
  2. Plug in your device
  3. Locate Universal Serial Bus Controllers > Apple Mobile Device USB Driver
  4. Right-click and select software update of the driver...
  5. Click Browse my computer for driver software
  6. Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
     C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers
  7. Click on let me pick from a list of drivers for devices on my computer
  8. Click on Apple Mobile Device USB Driver
  9. Click Next, then close and exit the Device Manager

  TT2

• HP 8600: impossible to Scan of both flat and ADF in a single document [new]

  This particular issue was published earlier, with no response. Since the November 2015 update, you cannot scan ADF and flat in a single pdf document. This will be corrected, or is the lost capacity for ever?

  Hello

  Full features software has this feature to select 'Source': ADF or Scan glass.

  If you prefer, you can try this:

  HP extended Scan

  FTP://FTP.HP.com/pub/scanners/HPScanExt/HPScanExt.msi

  Once it has downloaded and installed, go to start > all programs > HP > HP Scan extended > Run "HP Scan extended.

  Let us know if it works.

• Termination of IPSEC Services and anonymous logon

  Ending IPSEC Services

  , I receive the following event in the log to start. I also have a message of success for a logon by ANONYMOUS. I realize that this account peut be an issue of access network system using the (intentionally by MS?) Scary ID of ANONYMOUS but I am concerned about the fact that it could be something nasty.

  Details

  Product: Windows Operating System

  ID: 7023

  Source: Service Control Manager

  Version: 5.2

  Symbolic name: EVENT_SERVICE_EXIT_FAILED

  Message: The %1 service is stopped with the following error:

  %2

      

  Explanation

  The specified service has stopped unexpectedly with the error specified in the message. The service closed safely.

   

      

  User action

  To fix the error:

  Check the error information displayed in the message.

  To view error WIN32_EXIT_CODE SCM met, at the command prompt, type

  SC query service name

  The displayed information can help you troubleshoot the possible causes of the error.
  I tried every combo of syntax, that I can think of, but I can't this query to run.
  I got up and down from behind firewall router firewall protection more live Superantispyware more live Winpatrol and regularly scan with Malwarebytes and Microsoft Security Essentials. Secunia PSI keep an eye on the status of my programs. In this case, I ran additional full scans with all that I have more than 3 online scanners known.  All say CLEAN but I still get these messages. BTW account 'Guest' is disabled.
  
  
  Any help please?
  
  

  Hello

  Have you made changes on the computer before this problem?

  The following articles could be useful.
  IPSec tools and settings
  http://TechNet.Microsoft.com/en-us/library/cc738298%28WS.10%29.aspx
  IPSec troubleshooting tools
  http://TechNet.Microsoft.com/en-us/library/cc784300%28WS.10%29.aspx

• IPsec vpn and Anyconnect is denied by the ACL (unknown)

  I am trying to configure IPsec VPN and I used the wizard of asdm (asdm version 8.4, ASA version 8.4). At the moment he is not in production and is in a test environment. Whenever I try to VPN in I get an error on the asdm syslog saying "TCP access denied by ACL from x.x.x.122 to outside:x.x.x.225/443. So I allowed all VPN traffic to this IP address that is currently the IP address as the external interface. My acl is as follows:

  outside_in list extended access permit tcp any interface outside eq https

  outside_in list extended access permit tcp any host x.x.x.225 eq https

  Access-group outside_in in external interface

  Yet, I still get the same exact error. The strange thing about this error is that it does not give me the specific ACL that denies access. There is no other access lists that could possibly block this traffic.

  No idea what could be the cause this problem because I am confused.

  So far, if you have configured following does not require an acl.

  ciscoasa(config)#webvpn
  ciscoasa(config-webvpn)#enable outside
  ciscoasa(config-webvpn)#svc enable
  You can post configuration here someone can have a look on that.
  Thanks
  Ajay
  
  
  
  

• I'm trying to export a package layout custom in jpeg format of 3 photos that have been edited and arranged on a single printed page.  This was possible on LR4, but I just upgraded to LR6 and don't see how to do it?

  I'm trying to export a layout "custom package" as a single JPEG which consists of 3 photos that have been published and willing on a single printed page.  This was possible on LR4, but I just upgraded to LR6 and don't see how to do it?  Suggestions?

  It is still available in LR 6.  Exactly what did you do that you don't?  You may be using the wrong wording.  This is not a function of export; It's a "print to: JPEG File" in the print Module

  

• Can I use creative cloud on 2 computers (Mac and Windows) with a single license?

  Hello

  I have an individual license of creative cloud. Can I use creative cloud on 2 computers (Mac and Windows) with a single license?

  Yes, your single-user license allows unlimited installations (but limited to, at most, two concurrent connections and you can use only one at a time).

  Just install the application of cc desktop on any computer that you want to use with your subscription to the cc, Download Adobe Creative Cloud apps | CC free trial Adobe

• Can I run Premiere Pro CS6 and CC on a single computer?

  Can I run Premiere Pro CS6 and CC on a single computer?

  which means... then I installed it and used also (just in case) at the same time?

  THX in advance

  You can run as many versions of Adobe programs you want. For now, you can download and install PP CS6, CC and CC2014. If you want to install older versions (not only update this one you already have) you need to choose the previous Versions of the list of filters & Versions
  

• PIX 501 NAT and PAT with a single IP address

  Using the following configuration, on my first PIX 501, I am unable to provide a server of mail to the outside world and allows inside customers to browse the Internet. :

  6.3 (5) PIX version

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxx

  hostname fw-sam-01

  SAM domain name

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  No fixup not protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  outside access list permit tcp any host 62.x.x.109 eq smtp

  access the inside to allow tcp a whole list

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside the 62.177.x.x.x.255.248

  IP address inside 192.168.45.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 192.168.45.2 255.255.255.255 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  public static 62.177.x.x.x.45.2 (Interior, exterior) mask subnet 255.255.255.255 0 0

  outside access-group in external interface

  group-access to the Interior in the interface inside

  Route outside 0.0.0.0 0.x.x.x.177.208.105 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.45.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet 192.168.45.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd lease 3600

  dhcpd ping_timeout 750

  : end

  It is I'am using access list and groups wrong or am I wrong in PAT/NAT configuration.

  Please advise...

  Hello

  I went through the ongoing discussion. The pix configuration should be fine for now according to suggestions. The problems seems to be on the server. If it is a new installation of windows, then there is an option not to accept requests that are not local network.

  If you want to check if pix allows connections and then when you telnet to port 25 of the outside, just run the xlates control.

  SH xlate and it should show you a translation for the inside host. More than a quick test if pix allows traffic is to check 'sho-outdoor access list' and see if the counters are increasing.

  Hopefully this should help you.

  Arun S.

• Cable modem has no WAN port

  I have XFinity for my cable and internet services.  We just moved into a house built in 1850 and due to the size of the House and horse hair plaster, upstairs gets very little signal WiFi.  I want to extend the reach of WiFi and intended to do with a couple of Airport extreme.  The only problem is, every tutorial I watch shows the first Airport Extreme being plugged into the WAN port on the modem cable suppliers.  My router/modem, made by Cisco, has no port Ethernet WAN port only 4.  Can I connect the Airport Extreme on port 1 and then put in place using the Airport according to normal or need a WAN port?

  If you have a modem/router, then you would connect an Ethernet cable from one of the four ports Ethernet LAN <>-... choose any you want, they are all the same... to the "O" on the AirPort Extreme WAN port.

  Then use Configuration utility of Apple AirPort "Wizard" to configure AirPort Extreme to create a wireless network that uses the same exact wireless network and the same password that the wireless Cisco uses.

  The wizard will apply automatically other correct parameters... Mode Bridge, by example... so you don't have to worry about things like that.

• The WAN Port is communicating with the Ethernet switch?

  I have a Comcast gateway that the router is disabled in so it acts only as a modem. This is related to an Airport Extreme, which serves as my router via the WAN on the AE port. I created a different WAP with a Capsule temporal from the airport, located downstairs with an Ethernet cable from one of the Ethernet ports on the AE to the WAN on the TC port. I think it's what we call a 'roaming network.

  My question is, can I connect my switch Gigabit 8 ports in one of the Ethernet ports on the TC to complete connections wired to all devices connected on it, or should I first connect EI to the switch 8 ports and then connect the switch to the port WAN TC to complete my network "roaming"? In other words, plug it into the port WAN AE or TC still allows you to use other Ethernet ports as a switch?

  Thank you!

  can I plug my Gigabit 8 ports switch in one of the ports Ethernet on the TC to complete wired connections to all devices connected on it

  Yes, assuming that the TC has been configured to run in Bridge Mode, which would be normal.

  or should I first connect EI to the switch 8 ports and then connect the switch to the TC WAN port to complete my network "roaming"?

  It would be considered preferable to wiring, if it is convenient to do so.  For example, in the configuration of the wiring in the previous example just above... If there is a problem with the time Capsule, then all devices connected to the switch to the time Capsule would have a problem as well.

  If the switch is connected to the AirPort Extreme, and the TC is then connected to the switch... If the TC has a problem, the other devices connected to the switch of will not be affected.

• Satellite L - a single USB port works

  Hello

  I've had this laptop for a few months and I could not do all the USB ports work, the system recognizes all the but work alone. If I check the system it says ports are working properly and that it has the latest driver but when I do anything, a mouse, USB KEY, connect headsets to listen nothing, only one of the ports to recognize hardware.

  Can someone help me?

  Hi alecarrill63,

  It would be interesting to know what laptop you have exactly and what operating system you are using.
  Can you post this important information?

  In your case, I will try to update the Web from Toshiba site chipset driver

  But theoretically, if only a single USB port works, the other ports may be defective and therefore, it would be necessary to replace the motherboard. :(

• LAN/WAN ports not supposed to be Gigabit? Capped at 250Mbps, NOT because of the ISP LAN devices.

  Hi all

  Have a bit of a problem here. I have Internet Fiber-to-the-home (FTTH) with Bell Canada and have their Fibe Gigabit service which is 940/120 speeds up and down, respectively. I was able to bypass his combo modem/router using a switch connected to the optical network terminal (HAVE) where the fiber cable enters the House (which serves mainly my base modem) and using custom settings of VLAN and DNS in ports specific for my fiber IPTV service Bell and receivers work together through my router.

  So, I have a few routers that I tried this with to try to solve my problem. My Asus RT-AC5300 and others have no problem with having me my subscribed speed - certainly through devices connected to gigabit LAN and also via WiFi on compatible devices. But I'm not concerned about WiFi - it is specifically wired ethernet devices that are the cause. I use CAT5e and CAT6 cables only because he is a Gigabit connection. The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this? Is there something my Time Capsule prevents leave the LAN ports operating at gigabit full transfer speed? It is not only a device - I have multiple gigabit devices I tested, on all three of the TC ports, and none of them exceed 250Mbps. Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  Thanks for any ideas, comments or suggestions. Y at - it a setting I have accidentally enabled that is the cause? I had much rather use the TC of the most convenient airport for my network I was planning on getting multiple Airport extreme to position around the House to cover literally home WiFi and LAN bridges through the simple installation of these devices, but I do if I can't use my fiber subscribed speed.

  OR maybe I have a defective unit. Thanks again for the help!

  See you soon

  The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this?

  Apple AirPort routers have been designed to work with the cable standard and DSL connections.  The fiber is the new ball game, and Apple knows yet how to play the game, let alone to understand the rules.

  Most of the problems associated with connections to high speed on airports is a result of the decision of Apple to eliminate any kind of manual settings to manually adjust the speed of the WAN port on the router... and are based rather on an "Auto" setting.  Automatic adjustment seems to work pretty well on the fiber up to approximately 100 Mbps connections, but the WAN port is struggling to negotiate with high-speed connections when it is connected directly to the fiber. LAN ports can also be affected.

  Some users have reported that insert a Gigabit switch between the connection of the fiber and the Time Capsule or AirPort Extreme has helped with speeds. The theory here is that the switch can negotiate with the fiber connection much better than the WAN port on the Apple device.  If you have a handy Gigabit Ethernet switch, that it could not hurt to try this "Workaround".  Other users report no benefit when they try it.

  Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  The time Capsule is not directly connected to the fiber connection, so it OK to talk and negotiate with what he sees as a 'normal' a conventional router connection.

  Don't forget also that the 802.11ac products were designed before 2013. Current products have not changed since their introduction in June 2013.

  The bottom line... Apple needs to decide whether it wants to be an actor, or leave the routing other players company established. Such what, Apple is far behind the curve... my opinion.

  While it might not hurt to take the time Capsule to an Apple Store to check over the machine, you might want to ensure that they have in fact a fiber connection high speed to test.

• R7000 WAN Port does not use LAN as a substitute?

  I have a problem with my R7000. The WAN port is dead. I used it in access point mode for some time connected to one of my LAN ports, but I need to go back to a main router. Is it possible to run it in router mode outside of a LAN port, or I'm out of options and need to replace the router? Past the WAN port, everything works fine. Thank you!

  Ive never used Merlin, but I think you need to activate the dual WAN mode and just use the secondary interface for your main WAN while leaving the other disconnected.

• LRT224 - Dual WAN port forwarding

  Can you move forward say port 80 1 Wan IP and port 80 from WAN 2 to a different IP address. ?

  Also can you somehow choose TCP & UDP rather large only one or the other?

  I just replaced 2 routers with LRT 214 and LRT 224 TPLink its all works well. Except port forwarding

  With LRT224, a port forwarding rule is applied to the two WAN ports and two rules are necessary if you want to ship to TCP and UDP to the same internal IP address.