Cable modem has no WAN port

Similar Questions

• RV042 Dual WAN Port DMZ not acquire an IP from ISP

  Hello

  I am trying to replace my router with the more robust RV042 of current load balancing. Installation seems simple enough. However, I am having an issue gets an IP address of the DMZ port in load balancing mode.

  The two WAN is the same ISP and is both DSL, using the same models of DSL Modem. #1 WAN port works perfectly.

  Indeed, when an independent piece of equipment is installed in the #2 DSL modem, this gives an IP address instantly...

  The two DSL lines only require a MAC address to get their IP addresses, and none of the static values are allowed, perhaps to test only.

  The issue of intellectual property has been seen before. I can't find any reference to the iton this site.

  Thank you

  Steve

  Glad to hear that it works.

  The "save the settings and restart" is not all that rare, although it is not typical for your model.

  The obligation of power off is certainly not normal. He told me that some sort of electric lock has occurred. This could be a unique thing, caused by a discharge of static electricity, or it could indicate a manufacturing defect. If this is the first case he did re - is probably. If it is the latter, then it will need a trade at any given time.

  In any case, it seems that the MAC address index has been at least partially useful.

  Good luck, somone will be here if you need assistance once again.

• Connect the Airport Extreme via Powerlink to the cable Modem

  I have problems with wifi at home as the location where the my cable modem is far from ideal. I currently connected to an Airport Extreme, which works like the router (the cable modem has the router function disabled). Attached to the AE is also a powerlink and I have an Airport Express connected to the powerlink, which has its own network.

  I was wondering if it would make sense to connect the powerlink directly to the cable modem and then put my Airport Extreme, a more central location in my home connected via Powerlink and there accumulate this way, rather than the current configuration.

  I'm getting a second Airport Extreme soon as well and I have several express in my house, but the problem is that my wifi is not fast at all.

  Powerlink adapters are Devolo 600 & 1200.

  Thank you

  I was wondering if it would make sense to connect the powerlink directly to the cable modem and then put my Airport Extreme, a more central location in my home connected via Powerlink and there accumulate this way, rather than the current configuration.

  It's always a good idea to place the 'main' AirPort router as close as possible of the area where most of the wireless devices should be used in this sense, your idea is a good thing... and in theory at least. ... .the powerline adapters allow you to do.

  However, in practice... you won't really know how well... or even if... this type of installation will work until you try you. The reason for this is there is so many different things that can affect the performance of a type of current line of the installation program.

  If you have time, there is certainly no harm in trying this type of configuration.  Post your results if you decide to try it.

• Cable modem of CM600 default after large downloads

  Hi-

  I use a CM600 modem with a router WNDR-3700v4.

  Recently, the cable modem has started to behave very strangely after the download of large files (1 GB or more seem to be the trigger point). Once the download is complete, I started experiencing excessive latency and packet loss to external sites. Ping times jump around 20ms for 3000ms and package loss ranges from 0% to more than 50%. Restart the modem cable does not resolve the issue until I download another file of large size. Interestingly, I found that if I disconnect the cable modem LAN cable when it is defective, the modem still shows an activity and a LAN link on it. I expect the activity ceases when he is physically disconnected and link drop. I swapped the ethernet cable and it made no difference.

  If anyone of you thin people have ideas?

  Thank you very much!

  The modem has been replaced and the problem disappeared. Yay guaranteed.

• my modem STC (Saudi Arabia) SAGEM 007 has 4 ethernet ports. two of them do not work. (in red)

  my modem STC (Saudi Arabia) SAGEM 007 has 4 ethernet ports. two of them do not work. (in red)

  Hello

  You should check with the help of the manufacturer modem and if it is provided by your ISP support.

  Not really a Windows problem.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Can I connect printer to the usb port on the cable Modem CM100

  Hello

  This may seem like a stupid question, but here goes... I know that the usb port on my Linksys Cisco CM100 cable modem is an optional way to connect the modem to the computer. I wonder if I can use the usb port to connect my HP 1020 laser printer instead.

  The printer is not a network printer, and so I know that it may not work, but I have seen a few cases where a virtual port and install it as a local printer got to work.

  If I can connect the printer to the modem, and then he would give me a way to print from my laptop in the other room.  My printer is just beside my modem configuration and the router. I have a Linksys router WGR614 wireless who sees the devices on my network share, so I think he could see the printer connected to the modem (?)

  I couldn't find the answer to this anywhere. I didn't damage my equipment by blindly try this without knowing a little something. (I assume that the heart of my question is, on the CM100 usb port can be used for any usb device)?

  (I have Windows 7 64-bit operating system, in case you need to know).

  Thanks to anyone who can answer.

  djoseph

  A standard print server will allow you to connect a USB printer to your network. There are models wired and wireless depending on how you want to connect to the network.

• 2611XM gets WAN IP cable modem, but internet does not work

  Hello

  I have a strange problem with my 2611XM router. At home, that I que je suis am put my cable modem in Bridge mode and try to configure internet access via 2611XM router. Here are details on the configuration of the ILO

  interface FastEthernet0/0

  WAN description
  DHCP IP address
  NAT outside IP
  IP virtual-reassembly
  route IP cache flow
  automatic duplex
  automatic speed
  !
  interface FastEthernet0/1
  LAN description
  192.168.99.1 IP address 255.255.255.0
  IP nat inside
  IP virtual-reassembly
  automatic duplex
  automatic speed
  No mop enabled
  !
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 FastEthernet0/0
  !
  !
  IP http server
  local IP http authentication
  IP http secure server

  IP nat inside source map route SDM_RMAP_1 interface FastEthernet0/0 overload

  !
  access-list 101 permit ip 192.168.99.0 0.0.0.255 any
  !
  allowed SDM_RMAP_1 1 route map
  corresponds to the IP 101
  !
  !
  !
  control plan
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  Line con 0
  line to 0
  line vty 0 4
  privilege level 15
  password XXX
  local connection
  transport input telnet ssh
  !
  NTP-period clock 17208167
  !
  end

  The problem is that the internet is not accessible from 192.168.99.0 network. I can't even ping any public ip address of the router. Although I get successfully WAN ip on the fa0/0 interface of the cable modem. Any help appreciated.

  Thank you

  Hello

  Try below:

  no ip route 0.0.0.0 0.0.0.0 FastEthernet0/0
  no nat ip inside the source map route SDM_RMAP_1 interface FastEthernet0/0 overload
  no access list 101 didn't allow ip 192.168.99.0 0.0.0.255 any

  IP route 0.0.0.0 0.0.0.0 dhcp
  access-list 1 permit 192.168.99.0 0.0.0.255
  IP nat inside source list 1 interface FastEthernet0/0 overload

• Network: 2 routers Apple broadcasting separate wireless networks; one (Xfinity/Comcast) cable modem

  Hello community!  Need help, I want to use two routers to establish two separate wireless networks on a cable modem connection.  I searched for my answer and see some other threads on this topic, but all are either a bit too technical for me, are incomplete on the answers to my questions - and all seem to be locked.  I have also searched YouTube and only see videos to extend a network with two routers - not my goal.  So here is a long, but a detailed post on what I need someone help with - thank you very much in advance if anyone can all small-not me-I hope it will be useful to others in the future.

  The program installation/hardware: I have internet Comcast/Xfinity that runs to a Motorola surfboard cable modem (SB6141).  I also have two routers apple - a Time Capsule from Apple AirPort (to end 2013) and a new (2016) AirPort Extreme.

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  My plan is to have the cable modem Surfboard connect to airport Time Capsule, which will then connect to AirPort Extreme (even if it could be reverse - no difference, except that the data that I show below comes from the time Capsule, which is currently connected to the modem cable).

  To read the previous discussions, it seems that the starting point would be: modem router #1 Ethernet WAN, then a router cable #1 LAN Ethernet to the Router #2.

  First issue of clarification - the connecting cable should go to the Ethernet WAN port on the Router #2 or a LAN Ethernet port?

  Now that the first easy question is the road, I need help to configure two routers connected to allow two separate networks.  A lot of discussions about the positions of static IP addresses, cascade, etc..  I need specific help with AirPort Utility on what to change on what router.  It seems obvious that the settings under the 'Internet' and 'Network' tabs are those who need to set - the 'wireless' tabs simply treats the name of the wireless network and settings - these, at least I can understand!

  I'll organise this tabbed - here go us.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Next up, the 'Network' tab utility AirPort/window.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  If I click on the 'Network Options' button at the bottom of the window, it takes me to the "Networking Options" window Here I have areas of entry to specify the DHCP lease duration, can specify the DHCP IPv4 range, as well as part of the extended DHCP IPv4 comments.  There are checkboxes: enable NAT Port Mapping Protocol. Select the host by default (with input if selected text box); Enable the IGMP Snooping; Block incoming IPv6 connections; Allow the Teredo Tunnels; and allow inbound IPSec authentication.

  For this window, here is the current settings on the Router #1:

  DHCP lease is 1 day; Beach DHCP IPv6 is 10.1.2 to 200; Hosts IPv4 DHCP Range is 172.16.42.2 to 200.  The following check boxes are enabled/checked: enable NAT Port Mapping Protocol. Block incoming IPv6 connections; And allow inbound IPSec authentication.

  Who can help me? What parameters, if all do I need to change the #1 router?  How to set up router #2 to make a second wireless network?

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  What you really need is a combination router / Ethernet switches that s supports VLANdedicated. Given that Apple routers do not, at best, you can potentially get the results that you are looking for, but at a performance cost. In other words, you can have two separate WiFi networks where clients connected to a network can not 'see' those related to another and both routers will always provide access to the Internet through Comcast modem. Note: Arris / Motorola SB6141 isn't a gateway device. Instead, it's a simple modem. A gateway is a router modem combination.

  To do this, should do the following:

  • The Time Capsule (TC) would need to be directly connected to the modem using an Ethernet cable. This base station would remain in its default configuration of the router. In other words, the router Mode (in AirPort Utility) would establish: DHCP and NAT.
  • AirPort Extreme would be directly linked to TB by Ethernet. The cable must be connected to one of the LAN ports on the TC on the WAN port to the extreme. It must also be configured as a router. However, there are differences in the extreme:
    • Use a different name to the Wi - Fi network.
    • Use another range of IP DHCP address. By default, Apple base stations use IP addresses in the 10.0.x.x range. I suggest that you set the base station of the second on 192.168.x.x range.

  There is a major drawback with this configuration. The second base station will be in a State of "Double NAT". Although this "separating" the two networks on different subnets, this condition is not very effective and connected to this network of customers will get lower throughput performance. There is no way around it and it is not recommended.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  The two should be: DHCP.

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  These leave it as what. The TC is information of IP address of the modem. The extreme, he'll get the TC.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  These leave it as what.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Unless your ISP provides your IPv6 service, change the IPv6 configuration option to: 'Link-local only' on two base stations.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  Router mode should be: DHCP and NAT to two base stations. Ignore the DHCP reservations and Port settings for now. Let the current DHCP range for the TC. Change the DHCP range for extreme for: 192.168.1.2 a.200. At this point do not access control for each base station.

  Since you seem to need the step by step instructions or need help to understand the different terms networking, I highly recommend that you help you to become familiar with networking, specifically on Apple systems. I suggest you consider taking the e-Book to the next control: take control of your Wi - Fi Applehttps://www.takecontrolbooks.com/apple-wifi network

• The WAN Port is communicating with the Ethernet switch?

  I have a Comcast gateway that the router is disabled in so it acts only as a modem. This is related to an Airport Extreme, which serves as my router via the WAN on the AE port. I created a different WAP with a Capsule temporal from the airport, located downstairs with an Ethernet cable from one of the Ethernet ports on the AE to the WAN on the TC port. I think it's what we call a 'roaming network.

  My question is, can I connect my switch Gigabit 8 ports in one of the Ethernet ports on the TC to complete connections wired to all devices connected on it, or should I first connect EI to the switch 8 ports and then connect the switch to the port WAN TC to complete my network "roaming"? In other words, plug it into the port WAN AE or TC still allows you to use other Ethernet ports as a switch?

  Thank you!

  can I plug my Gigabit 8 ports switch in one of the ports Ethernet on the TC to complete wired connections to all devices connected on it

  Yes, assuming that the TC has been configured to run in Bridge Mode, which would be normal.

  or should I first connect EI to the switch 8 ports and then connect the switch to the TC WAN port to complete my network "roaming"?

  It would be considered preferable to wiring, if it is convenient to do so.  For example, in the configuration of the wiring in the previous example just above... If there is a problem with the time Capsule, then all devices connected to the switch to the time Capsule would have a problem as well.

  If the switch is connected to the AirPort Extreme, and the TC is then connected to the switch... If the TC has a problem, the other devices connected to the switch of will not be affected.

• LAN/WAN ports not supposed to be Gigabit? Capped at 250Mbps, NOT because of the ISP LAN devices.

  Hi all

  Have a bit of a problem here. I have Internet Fiber-to-the-home (FTTH) with Bell Canada and have their Fibe Gigabit service which is 940/120 speeds up and down, respectively. I was able to bypass his combo modem/router using a switch connected to the optical network terminal (HAVE) where the fiber cable enters the House (which serves mainly my base modem) and using custom settings of VLAN and DNS in ports specific for my fiber IPTV service Bell and receivers work together through my router.

  So, I have a few routers that I tried this with to try to solve my problem. My Asus RT-AC5300 and others have no problem with having me my subscribed speed - certainly through devices connected to gigabit LAN and also via WiFi on compatible devices. But I'm not concerned about WiFi - it is specifically wired ethernet devices that are the cause. I use CAT5e and CAT6 cables only because he is a Gigabit connection. The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this? Is there something my Time Capsule prevents leave the LAN ports operating at gigabit full transfer speed? It is not only a device - I have multiple gigabit devices I tested, on all three of the TC ports, and none of them exceed 250Mbps. Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  Thanks for any ideas, comments or suggestions. Y at - it a setting I have accidentally enabled that is the cause? I had much rather use the TC of the most convenient airport for my network I was planning on getting multiple Airport extreme to position around the House to cover literally home WiFi and LAN bridges through the simple installation of these devices, but I do if I can't use my fiber subscribed speed.

  OR maybe I have a defective unit. Thanks again for the help!

  See you soon

  The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this?

  Apple AirPort routers have been designed to work with the cable standard and DSL connections.  The fiber is the new ball game, and Apple knows yet how to play the game, let alone to understand the rules.

  Most of the problems associated with connections to high speed on airports is a result of the decision of Apple to eliminate any kind of manual settings to manually adjust the speed of the WAN port on the router... and are based rather on an "Auto" setting.  Automatic adjustment seems to work pretty well on the fiber up to approximately 100 Mbps connections, but the WAN port is struggling to negotiate with high-speed connections when it is connected directly to the fiber. LAN ports can also be affected.

  Some users have reported that insert a Gigabit switch between the connection of the fiber and the Time Capsule or AirPort Extreme has helped with speeds. The theory here is that the switch can negotiate with the fiber connection much better than the WAN port on the Apple device.  If you have a handy Gigabit Ethernet switch, that it could not hurt to try this "Workaround".  Other users report no benefit when they try it.

  Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  The time Capsule is not directly connected to the fiber connection, so it OK to talk and negotiate with what he sees as a 'normal' a conventional router connection.

  Don't forget also that the 802.11ac products were designed before 2013. Current products have not changed since their introduction in June 2013.

  The bottom line... Apple needs to decide whether it wants to be an actor, or leave the routing other players company established. Such what, Apple is far behind the curve... my opinion.

  While it might not hurt to take the time Capsule to an Apple Store to check over the machine, you might want to ensure that they have in fact a fiber connection high speed to test.

• Router is not connecting to the new cable modem

  Time Warner has replaced my cable modem with a Motorola SBV1521 and my Linksys BEFSR81 router cannot connect to it.  No lights for the WAN port when the modem is connected. I have tried everything what Linksys said in their "set up a Linksys router with cable Internet Service" including the upgrade of the firmware and pwer cycling. (I can connect to the modem when it is plugged into a LAN port, but not when it is plugged into the WAN port as it should). Any ideas?

  As a last resort, I swapped the two cables (one of the modem router and the other between the router and the main computer). It worked!

  Do not know why. The two are category 5 cables and the original path was working with the previous modem.

  I would be interested if anyone can explain this to me.

• cable modem-wireless combination or not?

  Hi, I'm going to switch from DSL to cable T - W (the only option in my building). I have an Airport Extreme on my TimeCapsule (it is the 500 GB disk version), that I use with my laptop. The iMac is connected to the router. I looked around at best buy where they sell T - W "approved" networking gear. Modems cable, all seem to be modem + units of combination of WiFi router at various points in price between about $80-200. My question is this: that any type of material that I use as long it's T - W compatible/approved. Any thoughts on the units of combination or is a cable modem + my Airport Extreme way to go. Not sure of the speed yet, but it is unlikely that I will contract for what that either more than 50 Mbit/s and perhaps even to 15 Mbps. Support some of the Motorola units that I was looking for very high flow rates, but they use the channel binding to achieve this goal. I read somewhere that if you buy the combined devices, you cannot update the firmware, but that doesn't make sense to me.

  Ask TW a modem without router built-in. And then run an Ethernet cable from the Ethernet port of the modem on the WAN on your AEBS port. You can connect your computer to the router either wired or wireless. It is the best configuration.

  If you do not need for Ethernet, then you can use a modem cable with router Wi - Fi as well. The main disadvantage is the difficulty you might have try to expand the modem/router using Apple hardware.

• WAG320N and cable modem connection

  I have a small question,

  You could point me to some reference material on my WAG320N configuration to use my modem cable via Ethernet 1 port. I saw that he mentioned it's possible, but I have been unable to me sorting.

  And before ask you, I put the DSL router that I move in the next 12 months and my new base will not have access to cable internet and I'll be going back to DSL.

  Thanks in advance,

  Phil

  Actually in this case your bad, but thank you for the quick response.

  After a few game, it seems that the WAG320N is specifically configured to configure Ethernet Port 1 WAN port and you can route all internet traffic through the modem cable via the WAN port, you just set up.

  If anyone is interested, then load up your routers page 192.168.1.1 default config.

  Click Setup

  - Ethernet

  Next to Ethernet connection: select the button labeled radio like Port WAN

  Most of the stand-alone cable modems will have a static IP address both under the list of connection

                           down box  Select the static IP address.

  Enter the IP address of your cable modem, subnet mask, gateway and DNS address by default. (These items must have all be supplied by your ISP)

  And finally click on Save settings at the bottom of the screen to validate your changes.

  Then connect to your WAG via the Ethernet switch or wireless connection and you should be good for surfing the web.

  I hope this helps someone else who tries to use a modem cable through the WAG320N or similar device.

• OfficeJet J6450 - printer connects wireless but does not print job cable modem replacement

  Material: My printer is an OfficeJet J6450. I am running Windows Vista, current update.

  Probably triggering the event: I replaced my modem docsis 3.0 with a doscis 2.0 modem. PSI has remained the same. All other software and firewall remained the same.

  Dysfunction: After the replacement of cable modem, I found that I could print is no longer in my HP OfficeJet 6450. I would get an error in the printer window ' error - print. "  After the reboot after the publication of the initial error, I would get the error "error - sent to the printer.

  What I did:

  As a first step, I've uninstalled and reinstalled the HP software for the printer (complete package with exception of PhotoSmart and HP customer monitoring program).

  Use the connection for the network printer wizard, I entered the router password wireless to the printer. At first I don't have a connection. Then I rebooted the computer and the printer. I also returned to the default setting of network on the printer and repeated the configuration of the network. The connection was finally successful.

  The automatic test of the network page and the network printer wizard confirms the connection. Digital display of the printer and the HP diagnostic utility has also confirmed the connection. But the diagnostic utility is unable to print a test page and throw an error - "Print Test failed.

  The result disappointing:  I still can't anything to print wireless.

  ... Thanks in advance for your suggestions to get my printer back on...

  Go to start > Control Panel > printers and delete all instances of the printer.

  Then re-add the printer:

  1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing.  Get IP address of a Test of Netowork wireless on the front of the printer (usually in the network menu).
  2. click on > start > Control Panel > printers.
  3. click on add a printer
  4. Select local printer
  5. Select create a new port and select Standard TCP/IP Port, and click Next.
  6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
  7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
  If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
  8. If prompted, use the driver that is currently installed.
  9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
  10. we may ask you to share the printer. Choose No.
  11. the printing area of Test Page is displayed. Go ahead and print it out.
  12. click on finish.

• HP Laserjet Pro P1102w printer: HP P1102w wireless printer will not pair with a SBG6782-AC Motorola Wireless Cable Modem Gateway

  I already had Internet AT & T U-verse using a Wireless Modem Arris IPDSL NVG510 gateway.  My laptop HP running Windows 8.1 and the HP LasrJet Pro P1102w wireless Prnter systematically and automatically connected to the wireless network NVG510 with no problems over the past two years and the wireless printer works without problem.

  I recently replaced the Internet AT & T U-verse connection a connection of Mbs Comcast Xfinity Intrnet 25, using a Motorola Arris SURFboard SBG6782-AC Wireless Cable Modem Gateway.   My HP under Win 8.1 Pro laptop connects to the network and access to Internet without any problems what-so-ever.  However, the HP LaserJet Pro P1102w wireless printer connects to the wireless network and I can't print at all from my laptop.

  I tried all the suggestions P1102w Wireless Configuration of the printer on the HP printer Support Site, but nothing helped.  I've also updated the firmware of the printer and Loaded the latest driver Installation & full product software.  I tried and re-tried these suggestions over the past two days, but without success.

  I would be very appreciately all help experts in this Forum.  to get the printer working wirelessly, since we also wireless print to this printer of IPads and other wireless laptops.

  Hi @Atmasin,

  I see that you have trouble connecting the printer to the new router. I want to help you.

  I would like to reset the printer first to clear the previous network settings.
  Turn the printer off, press and hold the wireless button and cancel (x button) while turning the printer on and do not release both buttons until the printer stops making the noise.

  Print a configuration report and check the SSID address and IP are disabled.
  Print a Configuration Page.

  If the network name has spaces or special characters, the printer may not recognize it.

  The printer is able to send/receive in the 2.4 ghz band.

  If it is set to 5 GHZ network, you may need to change to 2.4 ghz. (rename the 5 ghz or turn it off)

  The WPA key setting must be on AES to work properly not TKIP.

  Multi flow must be enabled.
  Router firewall must be open for printer ports.
  If you have Mac filtering give you printer hardware to meet the needs of the Configuration page.

  You may need to contact your router company to get help to check these settings.

  Try to run the Configuration Wizard wireless of the HP software to set up the printer on the network.

  If you appreciate my efforts, please click on the "Thumbs up" button below.

  If you have any questions, please let me know what steps you have taken and the results. Thank you.