Satellite L - a single USB port works

Similar Questions

• Satellite Pro L10-103 - USB ports not working not

  Hi, my Satellite Pro L10 - 103 USB Ports do not work. I tried different things and finally my Advisor rubbed my computer clean of all programs and operating system. After reloading of the set up disc and having lost my dear some programs I am no further forward. It still does not.

  Anyone know if this means that it is a mechanical problem with the computer? (I use Windows XP). Your help would be greatly appreciated.

  Hey Buddy,

  As wrote Akuma did you use the Toshiba Recovery disk or the Microsoft Windows disk?

  After installing XP, make sure that Service Pack 3 is installed. It contains important updates and can be downloaded on the official page of Toshiba.

  In addition, try to remove all the USB ports on the Device Manager, restart the computer. Ports will still be recognized and ready to use once.

• USB ports work very strange on my new Satellite L650D-100

  Hello, toshiba loaptop users and professional!

  Last week, I bought toshiba L650D-100 with windows 7, 64 bit. Everything is good, but the USB ports work strange:

  USB mouse works ok at a port and does not to another. It is not in the windows Device Manager, but if I connect or disconnect the device, it sounds "ding".
  With USB storage there is another problem: it appears in Device Manager and it is shown that drivers are ok and the device are working properly, but if I try to open it in Explorer, it crashes, green progress bar grows and stops at the end. This problem appears in the two ports.

  If I reboot laptop with usb storage pluged, it can start to work correctly, but if I unplug and plug again the problem reappear.

  Usb storage and usb mice work well on another computer. I've updated the bios, but it does not help.

  Help, please. Maybe I should try to reinstall the chipset driver? If so, where could I get?

  Hey,.

  > This may somehow worry about supply management food or feeding issues?
  In my opinion it has nothing to do with the power supply, or you may notice that the problem appears not on battery mode?

  In my opinion, you should follow the instructsions posted by Akuma. Recovery facility will show you if it s a hardware or software problem. ;)

• Satellite C650 problem with USB ports

  Hello

  I have a problem with my laptop, with my USB ports.

  A few days ago, I plugged my mp3 to charge its battery. I did when system Windows began and after a few ports seconds has stopped working. They work for one to five minutes after starting my computer, but only after my laptop's turn off for a few hours at night for example.

  They work fine and all of a sudden we hear the sound of a disconnected device and usb ports turns off. I tried many solutions but nothing worked. I removed all the USB ports in Device Manager.

  I checked in the BIOS, but everything seems to be okay. I tried to disable the disconnection of usb ports to save energy, nothing. Tools that have been provided by Toshiba to check hardware see as usb ports work correctly. Only usbdview program sees as unknown device, I tried to uninstall it through this program but still nothing.

  You have an idea, what could happen? Or if there is no possibility to fix without service visit?
  I would appreciate your help.

  Hello

  Have you tested these ports USB plug a USB mouse or a USB keyboard?
  These devices work properly?

  I don t think you need a visit to the service.
  I think that it s just a software problem
  Given that the USB ports are controlled by the chipset, I would recommend reinstalling/updating the chipset driver

  The alternative is a bit drastic, I think about the recovery of the laptop...
  It might be possible that the registry has been confused upward or some 3rd party software preinstalled on the laptop could affect the USB ports.

  I remember that my USB ports do not work after installing iTunes.
  I had to reinstall the operating system once more to get the USB port work even more funny is that I installed iTunes once more and USB worked correctly

• HP 15-AC152TX: NO USB PORT WORK

  Recently I bought HP 15-ac152tx and intalled Windows 7 ultimate (64 bit) using the CD player, but none of the USB ports work. I had already installed "Intel USB 3.0 host controller driver" always without success.

  Please give me the right solution for it.

  Hello:

  For the USB3, download, unzip and run the file setup.exe from the link below...

  https://Downloadcenter.Intel.com/download/22824/USB-3-0-driver-Intel-USB-3-0-Extensible-host-controller-driver-for-Intel-8-9-100-series-and-C220-C610-chipset-family

  Ethernet:

  This package contains the Realtek driver local area network (LAN) that allows the NIC (NIC) Realtek chip in the notebook models that are running an operating system supported.

  File name: sp71268.exe

  Video controller:

  This package provides the driver that allows graphics Intel high definition (HD) in the notebook models that are running an operating system supported. If the video output high-definition multimedia interface (HDMI) is supported, this package also installs the HDMI Audio Driver.

  File name: sp72651.exe

• No USB port works, code 32.

  Original title: no USB ports work

  All 3 ports on my Asus laptop don't work, here is the error message in the Device Manager ' a driver (service) for this device has been disabled.  Another driver can provide this functionality. (Code 32) ». Check updates, tried to uninstall & reinstall the drivers, nothing helps. The error message makes me think that perhaps something has disabled drivers, I might have accidentally downloaded a program that attempts to control the usb ports? Urrgh computers, not very good at this sort of thing talk in the language of the toddler please!

  [Moved from comments]

  I suggest you add updates at a time, until find you that is causing the problem.  Then uninstall it and install the rest.

• I can't do all the USB ports work - Evesham Style II Mini Office in Windows XP

  I'm looking for the chipset & drivers for my grandaughters computer, AFAIK is drawn next to a reading Speccy.

  O/S

  Windows XP Pro 32-Bit

  CENTRAL PROCESSING UNIT

  Intel Pentium 4 2.80 GHz

  Motherboard

  Manufacturer - Eveshamvale.

  Vend. ATI chipset.

  Chipset model - ID5833.

  Model Southbridge - SB200

  The downloaded manual provides the following information

  Model = P4SBA

  = North Bridge chipset; SiS 651 - South Bridge SiS 962

  CPU = Supports Socket 478 - Supports 400/533 MHz FSB

  I'd appreciate any help possible, that someone can give me as well as the Office works currently can't do all the USB ports work, they worked until I had to change the hard disk, but do not have the installation diskettes or the drivers.

  Hi Graham,

  Thanks for posting your query in the Microsoft Community Forums.

  I understand from the description of the problem, the USB ports don't work on Windows 7 computer.

  I understand this must be frustrating, but don't worry, we're here to help and guide you in the right direction.

  Method 1

  Run this fix - it and check if it helps.

  Diagnose and automatically fix the Windows USB problems

  http://support.Microsoft.com/mats/Windows_USB_diagnostics

  Method 2

  Reinstall the USB controllers.

  This method addresses the steps where the USB driver currently loaded became unstable or corrupted.

  To remove and reinstall all USB controllers, follow these steps:

  (a) click Start, click run, type sysdm.cpl in the Open box, and then click OK.

  (b) click on the hardware tab.

  (c) click the Device Manager button.

  (d) expand Bus USB controllers.

  (e) right click on each device under the Bus USB controllers node and then click Uninstall to remove them one at a time.

  (f) restart the computer and reinstall the USB controllers.

  (g) connect the removable USB storage device and perform a test to ensure that the problem is solved.

  I suggest you to contact the computer manufacturer and download the latest chipset drivers and check if it helps.

  It will be useful.

  Let us know if you encounter problems with Windows in the future. We will be happy to help you.

• None of my USB ports work

  My problem is the same... None of my USB ports work. I have disabled by mistake all and then discovered that my keyboard and mouse no longer work. I went into Setup and tried to allow them this way, but it did not work. I can go to Safe Mode and my arrow keys of the keyboard and enter the key work, but when it starts the key job. I am not able to get to Device Manager to turn them back on. I need help.
  TKS,
  Paul

  the work of the previous days your restore is completed.

  Use the restore option!
  Good luck!
  Chambers!

• After a reboot, none of the usb ports work and USB problems-uninstalled USB Ports

  I just bought a Seagate external drive, but none of my usb ports work. I looked into it and followed what it says on the uninstall of my USB ports, bad move on my part. Now, after a reboot, no usb port works, I've tried all microsoft support said to do and nothing seems to work. I think I need to reinstall my usb root hub? Perhaps, but I can't seem to find anyway to do. Help, please!

  Hello

  Check the status of the device in Device Manager. Follow the steps for the same thing:

  a. click on start

  b. click Run, in the Run dialog box type devmgmt.msc

  c. in the Device Manager window, locate the USB key and expand the drive, double-click the sub element to check if an error message or error code is listed.

  If there is no error message highlight Bus USB controllers and then click Action select check for material changes.

  You can check the link below: advanced troubleshooting tips for General USB for Windows XP problems: http://support.microsoft.com/?kbid=310575

• Satellite A200-1tw psae6e - USB ports not working not

  I use windows 7 ultimate on Satellite A200-1tw (psae6e-06u030du) and my usb ports no longer works correctly.
  In fact they recognize certain usb devices, but not all (for mouse and printer example work, but my USB does not work)

  Looking at the Device Manager, everything seems OK... No problem!

  Does anyone have a solution for my problem.

  Thanks :)

  Hello

  Try resetting the USB ports. This means that you need to remove the USB ports/hubs/controllers in Device Manager.
  Then, you have to restart the laptop to get new USB ports.
  In my case it has worked.

  By the way; I recommend upgrading the chipset driver and disable the feature for each energy-saving usb port.
  This can be done in the Device Manager-> port USB-> properties-> tab to save energy

• Satellite P200 - 17 c: USB ports do not work after BIOS update

  Hello

  Just updated my BIOS for my Satellite P200 - 17 c to version 1.80, running Vista Home.

  Now my USb ports do not work according to the normal when I insert flash drive microdrive or my Creative Zen MP3 player. (crash explore and not entirely file transfer)

  I just wanted to know if it is a known problem or is the problem unrelated to the update of the BIOS.

  Any info or advice would be great.

  See you soon.

  Glad you ve found a solution and thank you for sharing this with us

• Satellite C650 15Z two USB ports have stopped working / load

  Hi can someone throw their professional opinion on a current problem I am experiencing with my

  Satellite C650 15Z
  Windows 7

  There are 2 USB ports which are now both inoperative - there seems to be no power from them (ipad/phones do not charge) and any flash drive I insert does not appear as a drive in my computer
  and I don't hear audible alerts or message pop ups after insertion. Like I don't know what I look in Device Manager, I thought that someone may be able to help here?
  Thanks in advance

  Hello

  In Device Manager, you can try to delete and remove the USB host controller and USB hubs.
  All these devices are responsible for the functionality of USB ports.
  After you remove the USB host controller and USB hubs, restart the laptop.
  Usually the Windows operating system should recognize the devices automatically deleted after that, you can check if the USB feature is back.

• Satellite L855 - 14 p - USB ports do not work after the mode 'sleep'

  Heya guys,

  I have a strange problem today. The 2 USB inputs on the right side of the laptop (idk who is 2.0 or 3.0) does not work with the reason I can not perceive. These 2 guys are on different days, but in the same way. A month ago, I plugged the mouse USB wireless to one of them, then entered mode 'sleep'. When I came back, I discovered the work of mouse aint.

  Then I realized the port I plugged the key USB has no electiricity inside no more. I found it very strange and continuous without using the port of broken, until yesterday. Yesterday, I made the same mistake (a la mode "sleep" in a USB port plugged into the other port - work-) and I have re-opened, the 2nd port is broken in the same way, too. I've mastered Manager devices, regedit, but it has no use. This lead me to think his could be a hardware problem, but how can be possible? Is this a coincidence?

  Now, I have to use my 3rd and last port on the right side of the laptop with a USB duplicator.
  You have any ideas? Can it be a software problem?

  Understand this correctly? The USB ports mentioned don t work even after restarting a new laptop?

  In this case, it could be really a hardware problem
  But before talking about hardware problems, I recommend to recover the laptop using Toshiba recovery.

  Defining the notebook back to factory settings will help you identify the problem: If the USB ports wouldn't work, this s hardware problem.

• Satellite 4100XCDT: how the IRDA port works under DOS

  I have a Toshiba Satellite 4100xcdt. How do I assign a COM port to the IRDA (infrared) port in the BACK so I can use programs such as Winsamp
  http://www.veg.Nildram.co.UK/remote.htm

  The BIOS assigns COM1 and COM2 serial port to the built-in modem. However there is not a single option for the IRDA port not found.

  How can I make the IRDA port works under DOS?

  In my opinion it of not possible to use the IrDA DOS, because drivers must be installed and initialized.
  The IrDA port driver is a common Windows driver and the irda connection works only when windows was loaded

• L50-A-1FK satellite - cannot boot from USB port

  Hello

  I am a first user of this forum
  It is a problem with my computer and don't know how to fix it.

  My computer is a L50 A 1FK Satellite with Windows pre installed 8.1.

  I'm not impressed with new Windows10 and I'm back on Windows 8.1.

  What to do when I start to install a version of Linux Mint meadow look.
  It is impractical to restart the computer to. Al dough BIOS is changed by marketing, that to look for start-ups to the USB. It does not work. If I try the same thing is happening with a live CD or DVD.
  How can I make sure that there re-boot on the USB.

  As in advance,
  Rob (Wildspoor.nl)

  Hello

  In order to boot from external sources (CD or USB port - flash memory stick), you need to disable startup secure in the BIOS.

  There is also a startup mode option (UEFI).
  In case the new (Linux) system would not support UEFI mode, you must change this mode of CSM.