IR remote control does not work with the new imac

Similar Questions

• HP laserjet p1102w: wireless printer does not work with the new wireless network

  My office moved recently and we have a new wireless network. My printer always wireless worked perfectly on the previous network, but it does not work with the new network. I get a message "the printer is offline. I don't know how to reconfigure so that it detects the new wireless network. Can anyone help? Thank you

  Hi Shlomi,
  Thanks a lot for the info. I'll give it a try today...

• 128 - GB MicroSD card does not work with the new Clip +.

  My old Clip + (black, 8 GB) was getting very long in the tooth, so I ordered a replacement off Amazon.  As far as I know, it is identical to the old, but a very unpleasant difference is presented - it does not work with the MicroSD card which has been a huge part of why I got a Sansa at all.  He acknowledges, but after a media updated I'm lucky if more than one album appears.  And that's what's so crazy!  You just blow through the update in a few seconds, and when I navigate on the map, there is nothing or a handful of albums random, orphaned.  That's happened?  I updated the new Clip + for the current firmware (as I had done with previous); I made sure to reproduce all the parameters that I would be put in place before--I can't imagine what could be the cause!

  Treats quick closing:

  The card is formatted in FAT32 with the same sector size in storage aboard the player (32 768 bytes).

  A 64 GB card format works even without any problem.

  I tried to update the media in MTP and MSC mode; the problem is the same in both.

  There is ample space for MTABLE. SYS - I have not yet loaded all the music on the Clip + itself.

  Rockbox plays the card without problem, but the sound quality is horrible (at least on this player; I'm sure that other versions sound best), and its interface is a headache.  No thanks.

  HM.  Looks like to run CHKDSK /F on the map the problem resolved!

• Satellite A110 - switch WiFi does not work with the new WiFi card

  Hello everyone

  I have a problem with my laptop Toshiba Satellite A110 - 178 (PSAB0E). I replaced the original Intel 3945abg with Intel Link 5100 WIFI card and on the new wifi hardware wifi card switch does not work.

  New wifi card is discovered and drivers to the correct job but when I try to search with the Intel Pro/Wireless software wifi networks I message to turn on hardware switch, but there light and not work. The old wifi card swich works OK - orange light is on. On the new map light is off and swich does not work.

  Help, please

  Hello

  Do you have also enabled the WLAN functionality by pressing FN + F8?
  Check it!

  In addition, I think the case is clear: the new wireless LAN card isn't compatible with Satellite A110.
  So in my opinion, you must use remove the new card Intel and install the old card that works fine in your laptop.

• Portege M200: Rotation utility does not work with the new driver

  Hello

  I have a Portege M200 with the Gforce 5200Go. Since the last officially available graphics driver is the 46,44 I changed the 93.71 and installed. But the Rotation Utility does not work with this driver.

  When I use the driver nv for the rotation of the screen the tabletpen's is more synchronized: move the tabletpen left results in movement of the mouse to the top etc.

  Anyone any ideas?

  Hello

  You must use the page of the Toshiba driver graphics driver and not the original on the graphics card manufacturing site

• Utility HP does not work with the new update of Mac software

  I downloaded the latest version of the software for my Mac and now utility HP will not work! Any advice? Thanks, Chris

  Hey Chris. Looks like you may have the old software out there which is not compatiable with the new version of Mac OS X. What I would do is a complete uninstall of the HP software you have. Let's try this:

  We will uninstall with the option 'raccoon' like this:

  1. go in Applications/Hewlett Packard / click on uninstall HP and click on continue

  2. Select your device in the left pane
  3. hold the keys Ctrl, Opt and Cmd and click on uninstall
  4. There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  5. click on continue and let it finish

  Now run a software update. Before doing the next step make sure you connect your printer to the computer through USB. Then click on the Apple in the upper left corner of the screen, then clicking on software updates.

  If my instructions don't do because here's a little video to help out you:

• HP Color LaserJet CP2025n Prin: I need to download the older driver because a program does not work with the new driver

  Where can I find the olderdriver that I can use windows 64 bits 10,

  because a program does not with the new driver.

  The year may be 2014 or almost.

  Your Timo

  @tisalmet

  Thanks for the reply with the details,

  You can activate the Device Manager to view hidden devices by following the steps mentioned below:

  To work around this behavior and display devices when you click Show hidden devices:

  1. Click Start, point to programs, point to Accessories, and then click command prompt.
  2. At a command prompt, type the following command and press ENTER:

     Set devmgr_show_nonpresent_devices = 1

  3. Type the following command a command prompt and press ENTER:

     Start devmgmt.msc

  4. Troubleshoot the devices and drivers in Device Manager.

  For more details: click here

  Uninstall all software and drivers for printers:

  When you need to uninstall a driver completely, the best and safest method is to use the uninstaller of the device (if it has one). If you have added the device to your system with a Setup program (as is the case with most of the graphics card and sound card drivers, for example), you can uninstall it as you would any other program.

  1. Click Start, type uninstall program, and then press enter.
  2. In the uninstall window, which appears, scroll through the list and find your device or drivers. Double-click the entry to start the uninstall process.

  Sometimes devices will not have an uninstall program or the uninstall program will not appear in the list. In these cases, you can use Device Manager to remove the driver completely.

  1. Click Start, type Device Managerand press enter.
  2. Find and double click on the category of the device you want to uninstall (for example, the graphic card would be listed under display card) driver.
  3. Right click on the device, and then click Uninstall.
  4. Windows prompts you to confirm the removal of the device. Click OK to remove the driver.
  5. Once the uninstall is complete, restart your computer as soon as possible.

  Once the above steps are done, click here to download the full software features for your printer and follow the Setup process to start to use your printer again.

  I would like to know if these measures worked for you.  If they did, it's great!  Give us some reinforcements by clicking on the solution and laurels, buttons that help and others see that we have the answers!
  Good luck.

• Satellite L40-143 - WLAN does not work with the new router

  WLAN on my Satellite L40-143 does not work since I Modem Alice-1121.

  Who can help me, please!

  Hi kenny_21,

  If you have a new WLAN router you must change the configuration that I think

  The new router is visible under WLAN connections and can connect?

  If so try to connect. The standard router password can be found in the manual of it and no doubt, there will be new addresses MAC first before connect you. I put t know the exact configuration.

  Also check the options the WIRELESS card with TCP/IP. Usually, you need automatic IP addresses.

• Wireless camera does not work with the new router

  Hello, I'm having a problem with a camera D-Link DCS932L after you set up the EA4500.  The manual of the camera can be found here.

  http://d2okd4tdjucp2n.CloudFront.NET/DCs-932L_A1_Manual_v1.00 (NA) - en.PDF

  It worked fine with my old D-Link router.  The rest of the House has not had a problem with the EA4500.  There is a level of criticality around this camera certail and if I can't make it work, I'll have to return the router.  Configure the redirection of port as 5556 ~ 5559, TCP protocol (but I tried "Both" as well"with the IP address of the camera.  It still does not work.

  I craft but not in networks, i.e. I'm not stupid with tech but port quarrels is out of my comfort zone.  This camera with our old router setup took minutes.  I spent five hours trying to make it work on the EA4500.

  I guess you have the static IP value, or having a reserve of DHCP MAC address for the camera, network OK settings.

  What was the authentication wireless on the old router and that you use the new 4200?

  Is it possible that the camera does not support the encryption used by the 4200, i.e. wpa2-personal?

  Have you tried WEP to see if the unit works then?

• little emoji and emoji does not work with the new iOS update

  After installing the new iOS does not work. I uninstalled two emoji and re-installed. Does not work. Ideas?

  bitmoji has just released a new update today to correct this, check the app store for the update.

• My Norton anti-virus software used to work and now it does not work with the new Firefox update. This corrected soon? Otherwise, I will not use the product

  Since your last update that my Norton toolbar will not work... If it does not work, will not use your product. Can it be fixed quickly?

  According to the article, I linked to before, you will need to update the norton version 2015.2.1.13 toolbar that is compatible.

• Satellite L655-149: recovery does not work with the new HARD drive

  Satellite L655-149

  PSK1JE

  Windows 7 Home Premium 64-bit (factory installed)

  Recovery of HARD drive on drive D (factory installed)

  My old toshiba (MK5065GSX) 500 GB hard drive became too noisy and slow so I plan to replace it with the new drive hard toshiba (MK5059GSXP) 500 GB.

  I created USB Flash HARD drive recovery.
  When the installation is complete and Setup installs devices an error "Windows Setup couldn't configure windows to run on a hardware on this computer.

  I've updated the bios
  I loaded by default in the bios
  I changed the SATA AHCI mode to compatibility IDLE

  assistance in this regard will be highly appreciated

  Set the BIOS to the default settings and try again.

  With the installation of recovery, there is a problem: either it works or not. If this isn't the case, bad luck and the only solution for you is to order original Toshiba recovery DVD on https://backupmedia.toshiba.eu/landing.aspx

  By the way: do you use that stick of recovery for the first time?

• RoboFrom does not work with the new version of firefox v30.0

  My Firefox has been updated on 10-06-14 and now my RoboForm does not work

  Version 7.9.7
  http://www.RoboForm.com/platforms/Windows/Firefox

• Photomatix plugin does not work with the new update

  I use the Plugin "Merge to 32-bit" with the photomatix software make my HDR editing. With the new update of Adobe, this plugin has stopped working. Anyone know if it's because Adobe LR has blocked or something in that sense or is it just a bug in the new update?

  Photomatix has decided to go back to me again and this time with a link that fixes all photomatix plugins in LR. I've already tested and all included plugins fusion to 32 bit running again. Thanks to the team of photomatix.

  Photomatix Pro Plus Bundle Installer

• Remote control does not work, and the load does not appear on Apple TV

  Hello

  I just returned from vacation and my remote seems has stopped working.   Naturally, my first assumption was that the charge was simply exhausted.

  Apparently that was the case.   He seems to have just died.

  I did pay for more than two hours and it still does not appear under devices Apple TV.

  My Apple TV 4 works very well because I use the remote control of my phone to navigate through it.

  If I understand correctly what I look at you, it seems that the remote control is same not synchronized or recognized by Apple TV more.

  Any suggestions on how to fix this?

  A reset is complete? Restart... no change.

  Thank you

  Bob

  1. Have you tried pressing the menu and the button for a few seconds while it now an inch or two away from the Apple TV, if successful, you should see a message on the screen saying the remote was paired.
  2. If you have an older remote from a previous model MacBook or Apple TV, you can use to restore the Apple TV, which, in many cases, has been sufficient to reactivate the remote Siri. You must complete all upward to undertake a restoration.
  3. If you have a USB cable - C you can try to restore by connecting it to iTunes on a computer.
  4. If you have tried all of these steps, don't have a distance sooner or a USB - C cable or their use is too inconvenient, return it to the store where purchased for a replacement, or to couple for you.