IRQL_NOT_LESS_OR_EQUAL Windows 7
I was doing a bsod IRQL_NOT_LESS_OR_EQUAL approximately one minute after that I start windows. I can run it in SafeMode very well, and I have not recently installed a new hardware or software.
Technical information: * STOP: 0x0000000A (0 x 0000000000000000, 0 x 0000000000000002, 0 x 0000000000000001, xFFFFF80003A89C3F)
Any suggestions are appreciated. I am a noob to this computer stuff, so if I need to give more info just tell me where.
Thank you!
Patrick
Happy to help you.
You still have remnants of installed Symantec (ccsetx64.sys). You must use Symantecs uninstaller to get rid of all the bits.
These 2 were from the pilot checked and linked to the pilot of ndisrd.sys assistance NDISRD NT Kernel Resources. I would remove at least to test or so critical to current update
Microsoft (R) Windows debug 6.3.9600.17237 AMD64 Version
Copyright (c) Microsoft Corporation. All rights reserved.
Loading dump file [C:\Users\Ken\Desktop\New Minidump\110414-38360 - 01.dmp]
The mini kernel dump file: only registers and the trace of the stack are available
Symbol of validation of the path summary *.
Location of response time (ms)
Deferred SRV * D:\symbols* http://msdl.microsoft.com/download/symbols
Symbol search path is: SRV * D:\symbols* http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 7 Kernel Version 7601 (Service Pack 1) MP (8 procs) free x 64
Product: WinNt, suite: TerminalServer SingleUserTS
By: 7601.18409.amd64fre.win7sp1_gdr.140303 - 2144
Computer name:
Kernel base = 0xfffff800 '03 has 63000 PsLoadedModuleList = 0xfffff800' 03ca 6890
The debugging session: killed Nov. 4 16:08:18.919 2014 (UTC - 05:00)
System Uptime: 0 days 0:04:08.777
Loading the kernel symbols
...............................................................
................................................................
..........................................
Loading user symbols
Loading unloaded module list
....
*******************************************************************************
* *
* Bugcheck analysis *.
* *
*******************************************************************************
Use! analyze - v to obtain detailed debugging information.
BugCheck C4, {40, 0, fffff9800d128c00, 0}
WARNING: Unable to verify timestamp for ndisrd.sys
ERROR: Module load completed but symbols can be loaded for ndisrd.sys
Probably caused by: ndisrd.sys (ndisrd + 2716)
Follow-up: MachineOwner
---------
6: kd >! analyze - v
*******************************************************************************
* *
* Bugcheck analysis *.
* *
*******************************************************************************
DRIVER_VERIFIER_DETECTED_VIOLATION (c4)
A device driver attempting to corrupt the system has taken. It comes
because the driver was specified in the registry as being suspect (by the)
Administrator) and the kernel has allowed substantial control of this driver.
If the pilot attempts to corrupt the system, looking for bugs, 0xC4, 0xC1, and 0xA
Be one of the most commonly seen crashes.
Arguments:
Arg1: 0000000000000040, acquire a spinlock at IRQL level locking<>
Arg2: 0000000000000000, current IRQL
Arg3: fffff9800d128c00, address spinlock
Arg4: 0000000000000000
Debugging information:
------------------
BUGCHECK_STR: 0xc4_40
CURRENT_IRQL: 0
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: VERIFIER_ENABLED_VISTA_MINIDUMP
Nom_processus: NetSvcHelp.exe
ANALYSIS_VERSION: 6.3.9600.17237 (debuggers (dbg). 140716-0327) amd64fre
LAST_CONTROL_TRANSFER: from fffff80003f654ec to fffff80003ad8bc0
STACK_TEXT:
"fffff880 '0bb2f688 fffff800' 03f654ec: 00000000 ' 000000 c 4 00000000'00000040 00000000'00000000 fffff980 ' 0d128c00: nt! KeBugCheckEx
fffff880 '0bb2f690 fffff800' 03f762bf: 00000000'00000002 fffffa80 '066652e0 00000000 00000000' fffff800' 03f7369b: nt! VerifierBugCheckIfAppropriate + 0x3c
fffff880 '0bb2f6d0 fffff880' 0316a 716: fffffa80 ' 0cfceec0 fffff980 '0d128bb0 fffff980' 17ab4fb0 fffff880 ' 0bb2f798: nt! VerifierKeAcquireSpinLockAtDpcLevel + 0xa0
fffff880 '0bb2f730 fffffa80' 0cfceec0: fffff980'0d128bb0 fffff980 '17ab4fb0 fffff880' 0bb2f798 00000000' 00000000: ndisrd + 0 x 2716
fffff880 '0bb2f738 fffff980' 0d128bb0: fffff980'17ab4fb0 fffff880 '0bb2f798 00000000 00000000' fffff880' 0316bb99: 0xfffffa80'0cfceec0
fffff880 '0bb2f740 fffff980' 17ab4fb0: fffff880 '0bb2f798 00000000 00000000' fffff880' 0316bb99 00000000'00010001: 0xfffff980'0d128bb0
fffff880 '0bb2f748 fffff880' 0bb2f798: 00000000 00000000' fffff880 '0316bb99 00000000'00010001 fffff980' 17bd0ff0: 0xfffff980'17ab4fb0
fffff880'0bb2f750 00000000' 00000000: fffff880 '0316bb99 00000000'00010001 fffff980' 17bd0ff0 00000000' 00000000: 0xfffff880'0bb2f798
STACK_COMMAND: kb
FOLLOWUP_IP:
ndisrd + 2716
fffff880'0316 has 716? ???
SYMBOL_STACK_INDEX: 3
SYMBOL_NAME: ndisrd + 2716
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: ndisrd
Nom_image: ndisrd.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 4fc6df85
FAILURE_BUCKET_ID: X64_0xc4_40_VRF_ndisrd + 2716
BUCKET_ID: X64_0xc4_40_VRF_ndisrd + 2716
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:x64_0xc4_40_vrf_ndisrd + 2716
FAILURE_ID_HASH: {30bca9d7-111a-da6d-af09-4e1e9b7679e4}
Follow-up: MachineOwner
---------
Tags: Windows
Similar Questions
-
Hey guys, I had a few problems with the blue screens.
First of all, I'm on a brand new computer, hardware nine and new installation of Windows 7, including windows updates and all updates of pilot (that I know), as well as other software (eg games).
However, when I browse with Firefox (watch Youtube) or game too long, my computer blue screen and the blue screen tends to change. Sometimes, I have no information on the blue screen, sometimes it says IRQL_Not_Less_Or_Equal but sometimes also to mention storport.sys.
Upon restart, my blue screen error code is as follows:
Signature of the problem:
Problem event name: BlueScreen
OS version: 6.1.7601.2.1.0.256.48
Locale ID: 1033More information about the problem:
BCCode: d1
BCP1: 0000000000000000
BCP2: 0000000000000002
BCP3: 0000000000000000
BCP4: FFFFF880019750D2
OS version: 6_1_7601
Service Pack: 1_0
Product: 256_1I downloaded a .zip file of my minidumps, but also a sysdata.xml and a photo of the blue screen of my phone.
https://SkyDrive.live.com/?CID=e77c3ddd6b4ad7d1&ID=E77C3DDD6B4AD7D1! 316
Thank you very much in advance, I am really puzzled as to what to do.
Hello
Thanks for choosing Microsoft Community Forums.
According to the description, it seems that you are having problems with BSOD error messages while browsing the YouTube site with the FireFox browser. I will certainly help you fix this problem.
Since the system file posted, looks like you are having problems with the Intel AHCI drivers on your computer.
(1) was there any update of hardware controller or drivers of storage recently controller?
(2) have you made changes on the computer before this problem?
Method 1: If so, I suggest you to make back the drivers to the previous version and check if it helps.
Method 2: If this isn't the case, I suggest you to install drivers AHCI update from the Intel Web site or the manufacturer's Web site and check.
I hope it helps. If you have any questions about Windows in the future, please let us know. We will be happy to help you.
-
Display driver stopped responding and has fixed
I get the above error, I tried to find the driver display LENOVO G565 (Machine in Windows 8) but did not.
This error also showed on my ultimate windos7 before I upgraded to Windows 8.
CPD Watchdog Violation Windows 8
I also had this problem, and
IRQL_NOT_LESS_OR_EQUAL windows 8.
Could someone, Why these errors are happening and how to solve them.
We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.WE NEED AT LEAST TWO FILES DMP TO SPOT TRENDS AND TO CONFIRM THE DIAGNOSIS.
Please follow our instructions to find and download the files, we need to help you fix your computer. They can be found at hereIf you have any questions regarding the procedure, please ask -
Dv6-1020el: windows 10 dv6-1020el irql_not_less_or_equal
Hello
I've updated my laptop DV6-1020el of W7 to W10 (32 bit).
After updating I got often and randomly 0x00000a irql_not_less_or_equal error message.
The RAM is OK and no virus found.
She seems a driver issue, but how can I find what is the driver indicted?
Thx a lot.
KR
Unfortunately, there is no HP Win10 driver for your device. HP is not no matter what timetable indicating when, or IF, they will produce drivers for older machines.
You can try to use Windows updates to find the drivers from Microsoft deposits for your device: http://support.hp.com/us-en/document/c03330139
If that does not do anything, you should read this another link: http://support.hp.com/us-en/product/HP-Pavilion-dv6-6000-Entertainment-Notebook-PC-series/5048664/model/5077076/document/c04758308/
If Windows Update doesn't give new drivers, you can pursue alternative which are described in the linked Microsoft Windows Insider community thread: http://answers.microsoft.com/en-us/insider/wiki/insider_wintp-insider_devices/how-to-install-and-update-drivers-in-windows-10/a97bbbd1-9973-4d66-9a5b-291300006293
If you then run into trouble, install the drivers through Windows Update, you can try to use of Microsoft Windows Update Troubleshooter: http://windows.microsoft.com/en-us/windows7/open-the-windows-update-troubleshooter
Good luck -
IRQL_NOT_LESS_OR_EQUAL 0x0000000A after installing Windows updates
Blue screen with the following information:
IQRL_NOT_LESS_OR_EQUALSTOP: OxOOOOOOOA
I get this error for the second time in two months on a Lenovo R61 laptop after installation of the latest version of Windows Update there is very little time. Sometimes after a few minutes after the start-up of the machine without provication. The first time was the same scenario, but seemed to go away after a week or so mysteriously. I used the laptop for almost a year with no problems before installing updates.
I have Vista pre-installed with the recent updates installed.
I don't have a new hardware or drivers that could lead to conflict - it comes factory all installed on the laptop.
I have 2 GB of RAM, but I have a NVIDIA chipset.
I tried the defragmentation tools, system repair, etc. without change to the problem. Any advice?
Hello
Check the updates of Windows to see if a driver has been updated all the time that these questions came.
Cause
This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.
The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.
If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.
Solve the problem
If a kernel debugger is available, get a stack trace.
To resolve an error caused by the faulty device driver or service system, BIOS
- Restart your computer.
- Press F8 to character-based menu that displays the choice of operating system.
- In the Windows Advanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.
To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool
- Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
- Try disabling the cache in memory of the BIOS.
- Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
- Make sure that the latest Service Pack is installed.
- If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
- For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.
If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.
Comments
Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.
--------------------------------------------------------------
My generic bluescreen problem:
Hello
Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
information on all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.
You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
system installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-----------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
smile, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob - bicycle - Mark Twain said it is good.
-
When you install Windows XP I IRQL_NOT_LESS_OR_EQUAL error message
IRQL_NOT_LESS_OR_EQUAL, STOP: 0X00000000A (0X00000002, 0X00000000, 0X00000010, 0X8051AA58)
I have a brand new everything except the hard drive and hard drive. When I try to install Windows XP from the Dell Windows Professional CD it will install on the Setup screen when you partition the hard drive, but when it starts to install Windows its self, it will go to a blue screen after about 30 seconds.My computer is a NZXT 59 tour a Corsair 400w power supply, a mother DG41TY, a processor E5300, Council a HDD Maxtor 500 g and 1 GB of DDR2 RAM.
Well, the main issue is that you cannot use a Dell Windows XP reinstall on one different computer than Dell drive. You don't have a Dell computer because the motherboard came not from Dell. The only thing you can do is purchase a classic Microsoft Windows XP Professional or better yet, buy Windows 7 Professional. Carey Frisch
-
I'll try to be complete, I'm quite technically competent in implementing network and equipment and have been working on this for over a week.
HP Pavilion under Vista SP2 desktop computer. 2x2gb sticks of RAM.PC a friend, apparently blue screened during the connection of its new iPhone 5. As I said in the title, the blue screen seems to alternate between Memory_Management and IRQL_NOT_LESS_OR_EQUAL. I can start in safe mode but impossible to activate the Windows service install. I installed SafeMSI and always impossible to uninstall anything. I installed Revo Uninstaller, uninstall of Windows/application still does not work, but I used it to remove iTunes, Apple Mobile Device Support, etc. Also, I can't use any network in safe mode even when the boot safe mode with networking so I can't check for solutions online. I did comprehensive RAM test-run Windows diagnostics, diagnostics of HP, MemTest86 or about (ran without error) 8, tried with each RAM stick only, tried with each in different locations, tried with two other sticks of 1 GB matched RAM, try with a different from 2 GB RAM stick, tried in all four memory locations. I also ran ComboFix and MalwareBytes, Chkdsk, sfc /scannow...and probably others that I can't think of right now. I was going to just to reinstall Windows, but when you start the ISO that he allow me to upgrade, it will wipe the data. Same thing when running in safe mode. It blue screens a few seconds to load the office so I have no time to do anything normal start-up. Oh, I also did a start diagnosis "clean boot", etc. - blue screen every few seconds. When I boot mode safe, it works well with the obvious exception of services that I have to solve it. I also tried to boot to the last good configuration, try the Startup Repair and attempted a system restore, but event viewer informed me that all the restore points had been deleted for one reason or other. Any help would be appreciated.Thank youChrisChris
More than 80% of them were directly related to your Symantec and many others indirectly. I would also like to delete AVG.
I would replace both with MSE. BTW, you win most DMP files presented by a long shot (255).
Symantec is a common cause of BSOD.
I remove and replace it with Microsoft Security Essentials at LEAST FOR TESTER
http://us.Norton.com/support/kb/web_view.jsp?wv_type=public_web&docURL=20080710133834ENUse it to Norton 360 http://Symantec.pcperformancetools.com/Norton-360-how-to-uninstall.html -
I have Windows Vista. It crashes on me. The last message I got was:
PILOT: IRQL_NOT_LESS_OR_EQUAL
STOP: 0 x % x 081 (0 x %p, 0 x %p, 0 x %p, 0 x %p)
Please help me solve the problem.
Original title: frequent dumps
The main question in bold:
Update your drivers for chipset NVIDIA nForce for later.nvmfdx32 nvmfdx32.sys Wednesday May 21 13:47:38 2008 (4834603A)
NVRAID nvraid.sys Wed Jun 06 16:34:41 2007 (46671A 61)
nvstor32 nvstor32.sys Fri Jun 06 22:07:49 2008 (4849ED75)---------------------------
The value of the bios Optimized Defaults.
---------------------------
Update Realtek HD Audio codec driver on their main page on the right side.
---------------------------
Delete this file, and then restart:
C:\Windows\System32\drivers\PxHelp20.sys
PxHelp20 PxHelp20.sys Wed Mar 12 21:57:44 2008 (47D88A18)
Then fix the CD/DVD drive with the manual method here:
http://support.Microsoft.com/kb/314060
-----------------
Update Driver graphic card for more later:
nvlddmkm nvlddmkm.sys Thu May 22 18:51:06 2008 (4835F8DA)
http://www.nvidia.com
-
Here is the block reports Poblem in Control Panel.
Signature of the problem
Files helping to describe the problem (some files may be is no longer available)
Additional information about the problem
Information about the server: 07578b82-1d9f-411b-95f5-1460cdc12f6a
Hello
Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65----------------------------------------------------------
BCCode: 0a 0x0000000A
Drivers could be at fault, however the problems of disk or security/antivirus/antispyware products are
just as likely to be the root cause that they can force a driver to corrupt or go out of bounds.
The video driver or something affecting it would be questionable.At the end of this message, I'll post a bluescreen generic and in the next convenience store
How do to update the drivers and BIOS but also to check memory message.-----------------------------------
BCCode: 0a 0x0000000A
Cause
This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.
The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.
If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.
Solve the problem
If a kernel debugger is available, get a stack trace.
To resolve an error caused by the faulty device driver or service system, BIOS
- Restart your computer.
- Press F8 to character-based menu that displays the choice of operating system.
- In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.
To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool
- Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
- Try disabling the cache in memory of the BIOS.
- Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
- Make sure that the latest Service Pack is installed.
- If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
- For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.
If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.
Comments
Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.
BCCode: 0a 0x0000000A<-- read="" this="">-->
* 1025.html http://www.faultwire.com/solutions-fatal_error/IRQL-not-less-or-Equal-0x0000000A-==================================================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
hangs and displays information about all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do without if needed fail or the Vista DVD or recovery command prompt mode
Options if your system was installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
I tried to update my system Windows 7 to Windows 10, but during the installation, I got the IRQL_NOT_LESS_OR_EQUAL blue screen and after it restored to Windows 7 I got the notification that the installation of Windows 10 stopped with the 0xC1900101 error code - 0x2000C.
After I disabled most of my hardware and uninstalled all of my programs, who have used the virtual hardware and I still have this error I tried to reinstall Windows 7. But during the installation, I got a blue screen with the same error and technical information, I do not understand:
(Sorry, I don't have all of the 2nd to the last line, but the only thing missing is a 0)
So I guess it must be a hardware problem. Can someone identify what problem it is maybe?
As I read somewhere, it might be due to the RAM, I ran MemTest86, but unfortunately I do not know how to interpret the results. I only noticed, which proved of MemTest86 memory, addresses that should not exist as far as I know that (I) have 8 GB of RAM and the only errors were produced in some of these addresses:
That would mean, the RAM is responsible for the blue screen? And if so, can it be fixed, or I have to buy new RAM?
My system:
CPU: Intel i5-750
GPU: MSI GTX 970 games 4G
RAM: 2 x G.Skill 4 GB DDR3 DIMM Kit - 1600
Radio: Samsung EcoGreen F2 1.5 TB, SATA 3 Gb/s (HD154UI)
Thank you in advance for your help!
If you need additional information, feel free to ask.
Enter the BIOS a voltage increase of memory by a small amount, and then relaunch Memtest86. As is - what you are configured to use XMP mode?
You have the most recent version
Memtest86 +:
This is going from a boot floppy / CD or USB and must eliminate or confirm if one or more of your sticks of memory are bad or the values of the SPD in the BIOS are correct.
Let it run for as long as you can: 2,4,6,8 or several hours (at least 3 full passes), if no errors at that time then your ram is OK.
Memtest86 + Guide/How To (use the.) ISO to create a bootable CD)
http://www.overclockers.com/forums/showthread.php?t=409152
Auto Installer for USB:
http://www.memtest.org/download/5.01/Memtest86+-5.01.USB.Installer.zip
J W Stuart: http://www.pagestart.com
-
I just got it, I had to launch a Malwaresbytes update and PrivaZer was launched and at the same time. This is the first time I see that the origin of the problem, generally, it is my software Bitdefender that do.
General informationBug check code
0x0000000A Bug control chain
IRQL_NOT_LESS_OR_EQUAL 1 listen
0xFFFFF88000961008 2 listen
0 x 0000000000000002 3 listen
0 x 0000000000000001 4 listen
0xFFFFF80003674AE9 Date of the crash
19/03/2015-05:37 Architecture
x 64 Major version
15 Minor version
7601 Number of processors
4 Size dump file of the
256 KB Crash of the sourceCrash of the source
Hidclass.sys + 20006370F20 Path
C:\Windows\system32\drivers\hidclass.sys Description
HID class library Version
6.1.7601.18199 Company
Microsoft Corporation Size
75 KB Call stackAddress of the stack
Ntoskrnl.exe + 74469 Address of the stack
Ntoskrnl.exe + 23AE9 Address of the stack
Hidclass.sys + 20006370F20 Address of the stack
Ntoskrnl.exe + 377420 Sorry it's in French but the locations are the same as in English.
Hello
References to Vista also apply to Windows 7.
This is my generic how updates of appropriate driver:
This utility, it is easy see which versions are loaded: run DriverView - set the VIEW to hide
Microsoft drivers - update those without drain in their names. (Also update the BIOS and the weak)
level chipset drivers on the site of the constructor/the system motherboard.)-Free - DriverView utility displays the list of all device drivers currently loaded on your system.
For each driver in the list, additional useful information is displayed: load address of the driver,
Description, version, product name, company that created the driver and more.
http://www.NirSoft.NET/utils/DriverView.htmlFor drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
Control Panel - device - Graphics Manager - note the brand and complete model
your video card - double - tab of the driver - write version information. Now, click on update
Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
Uninstall - REBOOT it will refresh the driver stack.Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
with their own software and drivers and all other main drivers that you have.Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
BIOS, Chipset and software updates on the site of the manufacturer of the system here.)Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
each installation.Always check in the Device Manager - drivers tab to be sure the version you actually install
presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
in particular that) so to install a driver - reboot - check that it is installed and repeat as
necessary.Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
manually by model.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers to 7 (updated drivers manually using the methods above is)
to ensure that the latest drivers from the manufacturer of system and device manufacturers are are preferably)
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlIf you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
Updates, this leaves ONE of Windows updates, but it will not install the drivers who will be generally
be older and cause problems. If updates offers a new driver and then HIDE it (right click on it)
and then go look for new ones manually if you wish.How to stop Windows 7 automatically install drivers
http://support.Microsoft.com/kb/2500967==========================================
Tests of memory intercept all errors such as memory do not match (possible even for sticks
seemingly identical) and when the faster memory is placed in system behind the slower memory.
So it is best to Exchange also sticks in and out to check for those, even if all the tests of memory do not
show a problem.To test the RAM here control - run 4 + hours or so.<-- best="">-->
www.memtest.orgFor the Windows Memory Diagnostic tool.
Start - type in the search-> memory box - find top - click - right Memory Diagnostics tool
RUN AS ADMIN follow the instructionsWindows Vista: How to scan / test your memory with Windows Vista memory or RAM
Diagnostic tool
http://www.shivaranjan.com/2007/11/01/Windows-Vista-how-to-scan-test-your-RAM-or-memory-with-Windows-Vista-memory-diagnostic-tool/How to run the diagnostic tool memory in Windows 7
http://www.SevenForums.com/tutorials/715-memory-diagnostics-tool.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
Windows 7 error: IRQL_NOT_LESS_OR_EQUAL Stop: 0x0000000A
I have a laptop Dell Inspiron.
I installed the OS from Vista to Windows 7
I think that the upgrade successfully compleed... There was no failure I've seen during the upgrade.
Immediately after the upgrade, reagardless of what app I'm running, I repeatidly receive the IRQL_NOT_LESS_OR_EQUAL Error in a few minutes.
Hello
1. which edition of Windows are you running?
Example: Windows 7 Professional 64-bit
2. When you receive this error message?
Please follow the links below to solve the problem.
Method 1Resolve stop (blue screen) error in Windows 7
http://windows.microsoft.com/en-us/windows7/Resolving-stop-blue-screen-errors-in-Windows-
Method 2Please download and install this fix to see if the problem is resolved.Stop error message when there is a request to allocate a large contiguous physical memory amount in Windows Server 2008 R2 or Windows 7: "Stop 0x000000A (IRQL_NOT_LESS_OR_EQUAL) error code.Method 3
Try to run in a clean boot state and look for errors.How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
Note:
please follow step 7 of the article mentioned above to start the computer normally, once you have completed the necessary troubleshooting.Please post the results of the resolution of the problems.I hope this helps.
-
IRQL_NOT_LESS_OR_EQUAL update windows 8.1
Hey,.
I tried to update my windows computer 8.0 to 8.1 and when this is done, the computer gives me a blue screen and indicates that an error was foundError: "IRQL_NOT_LESS_OR_EQUAL"I found other answers for this error, but not for the update to 8.0 8.1 tilAll my cables plugged in, and I have no idea what to do!I heard the update was very cool and I really want it!
Thanks :)Andi
You drag the files to the desktop? If you can't we file, we cannot tell you what the problem is.
-
Windows 8 bluescreen IRQL_NOT_LESS_OR_EQUAL
so I get this blue screen about once a day only when playing League of Legends
IRQL_NOT_LESS_OR_EQUAL (e22w8x64.sys)
any thoughts on this problem you can be?
A nailed! :) Thank you for sticking with it!
Crash details.
Use! analyze - v to obtain detailed debugging information.
BugCheck D1, {fffff88010fe7000, 2, 0, fffff8800661c353}
Cannot load the image \SystemRoot\system32\DRIVERS\e22w8x64.sys, 0n2 error Win32
WARNING: Unable to verify timestamp for e22w8x64.sys
ERROR: Module load completed but symbols can be loaded for e22w8x64.sys
Probably caused by: e22w8x64.sys (e22w8x64 + c 1 353)Follow-up: MachineOwner
DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)
An attempt was made to access an address pageable (or completely invalid) to a
application interrupt level (IRQL) that is too high. It is usually
caused by drivers using a wrong address.
If the kernel debugger is available, get a stack backtrace.
Arguments:
Arg1: fffff88010fe7000, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000000, value 0 = read operation, 1 = write operation
Arg4: fffff8800661c353, address memoryDebugging information:
------------------Now, here's what you need to do. Take the steps in the link below, and monitor the system.
http://service.msicomputer.com/msi_user/support/TechFAQdetail.aspx?formid=3054
If accident stops, then you're good to go.
In addition, please uninstall each instance of NTIOLib_X64.sys and any program or utility.
Description of the driver: Driver MSI Afterburner ( known problems with Windows BSOD ) also found that part of MSI Live Update 5
NTIOLib_X64 NTIOLib_X64.sys Thu Oct 25 06:27:58 2012 (5089142E)
NTIOLib_X64_fffff8800daf8000 NTIOLib_X64.sys Thu Sep 25 21:46:44 2012 (5089EB84)
NTIOLib_X64_fffff8800db16000 NTIOLib_X64.sys Sun Nov 18 23:32:58 2012 (50A9B67A)
NTIOLib_X64_fffff8800db1d000 NTIOLib_X64.sys 20 Mar Nov 03:14:23 2012 (50AB3BDF)
NTIOLib_X64_fffff8800db24000 NTIOLib_X64.sys 20 Mar Nov 03:19:18 2012 (50AB3D06) -
IRQL_NOT_LESS_OR_EQUAL BSOD Windows 8
My computer has recently been blocked every time the screen goes blue and it says the cause of was irql_not_less_or_equal, has happened four times now, I have reinstalled my graphics drivers from AMD, twice, twice the completely uninstalled and then reinstalled, it still happens so I don't think that is the problem... even though most of the posts online say that it is probably the cause. It happened once in game, and then all other times happened while on Skype and I watch a video, or alt-tabing out a game on, most of the time Skype. I bought this laptop 2 months ago, and all I've done is played games on it and installed the necessary software and all my drivers updated. I don't have a clue as to what caused it or what to do... Help please thank you. Blue screen display gave me this-
042014-60793 - 01.dmp 20/04/2014-19:19:46 IRQL_NOT_LESS_OR_EQUAL 0x0000000a 000000 a 6 '673bfb10 00000000' 0000000f 00000000 00000001' fffff803' bbc47367 hal.dll hal.dll 37367 + x 64 + 5 ntoskrnl.exe has 440 C:\Windows\Minidump\042014-60793-01.dmp 4 15 9200 280 784 4/20/2014 19:21:50
and this-
041814-49967 - 01.DMP 18/04/2014 22:32:02 IRQL_NOT_LESS_OR_EQUAL 0x0000000a 000000 a 0'21defc58 00000000' 0000000f 00000000 00000000' fffff801 449953 c 0 hal.dll hal.dll + 373c0 x 64 + 5 ntoskrnl.exe has 440 C:\Windows\Minidump\041814-49967-01.dmp 4 15 9200 280 728 4/18/2014 22:33:44
In addition, another answer on this site said to CBS in CMD, I don't know how the read or know what to do with it but the CMD says he found that he could not fix corrupt files... Here is a link to the CBS.log https://www.mediafire.com/?bzas4ak0w99ihbz newspaper
I have no idea how to read this or the blue screen information and have no idea what to do... If someone could tell me what I can do to stop these errors, it would be a great help.
Also, I'm sorry if I've put this in the wrong topic, could not choose between repair and recovery, or performance and maintenance.
Worlds
Service of soluto was referenced in this crash, but not a direct involvement.
1: kd >! analyze - v
*******************************************************************************
* *
* Bugcheck analysis *.
* *
*******************************************************************************IRQL_NOT_LESS_OR_EQUAL (a)
An attempt was made to access an address pageable (or completely invalid) to a
application interrupt level (IRQL) that is too high. It is usually
caused by drivers using a wrong address.
If a kernel debugger is available, download the stack trace.
Arguments:
Arg1: 000000a6673bfb10, memory referenced
Arg2: 000000000000000f, IRQL
Arg3: 0000000000000001, bit field:
bit 0: value 0 = read operation, 1 = write operation
bit 3: value 0 = not an enforcement operation, 1 = performance operation (only on chips that support this level of State)
Arg4: fffff803bbc47367, address memoryDebugging information:
------------------WRITE_ADDRESS: GetPointerFromAddress: unable to read from fffff803bbfd4168
Unable to get nt! MmPoolCodeStart
Unable to get nt! MmPoolCodeEnd
000000a6673bfb10CURRENT_IRQL: f
FAULTING_IP:
HAL! HalpPciReadMmConfigUlong + 7
fffff803'bbc47367 8902 mov dword ptr [rdx], eaxDEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
BUGCHECK_STR: 0XA
Nom_processus: SolutoService.
TRAP_FRAME: fffff8801c0df190-(.trap 0xfffff8801c0df190)
NOTE: The frame trap does contain not all registers.
Some registry values can be set to zero or incorrect.
Rax = 0000000000404000 rbx = 0000000000000000 rcx = ffffffffffd0e000
RDX = 000000a6673bfb10 rsi = 0000000000000000 rdi = 0000000000000000
RIP = fffff803bbc47367 rsp = fffff8801c0df328 rbp = ffffffffffd0e000
000000000000008c = c 000000000000008 r10 = 0000000000000000 R8 = r9
R11 = fffff803bbc52f60 r12 = 0000000000000000 r13 = 0000000000000000
R14 = 0000000000000000 r15 = 0000000000000000
iopl = 0 nv up ei pl zr po nc
HAL! HalpPciReadMmConfigUlong + 0x7:
fffff803 'bbc47367 8902 mov dword ptr [rdx], eax ds:000000 a 6' 673bfb10 =?
Reset the default scopeLAST_CONTROL_TRANSFER: from fffff803bbcd5769 to fffff803bbcd6440
I suggest that you remove AVG completely and replace with Windows defender, at least for a period of time to see if the crashes stop.
AVG REMOVER
http://www.Avg.com/us-en/utilities
How to turn Windows Defender real-time Protection on or off in Windows 8 and 8.1
http://www.eightforums.com/tutorials/21962-Windows-Defender-turn-off-Windows-8-a.html
Also uninstall and reinstall the service of soluto, although I recommend to leave uninstalled.
Maybe you are looking for
-
Impossible to cancel always "use private surfing."
I have checked the box 'always use private surfing'.After the installation of 35.0 I can't turn.As soon as I uncheck this box FF restarts. BUT even once in private. And the box remains checked.I tried everything: config setting 'browser.privatebrowsi
-
I did the ios 9.3.1 update for my Iphone no longer live 6s April 1. After updating my phone gets hot in normal use wifi and battery drains too quickly. is there anyone facing the same problem too? my phone will not last for the full load of the day.
-
Get the event 680 Viewer when the guest account is disabled in Windows 2003
Hello We have "guest" account disabled on Windows 2003, but again we see events like this 2 Jul 01:58:33 192.168.80.11 security MSWinEventLog 0 5768968 Sun Jul 01 15:58:32 2012 has 680 xxxxhostnamexxx Audit of the failures of the security user SYSTEM
-
Bluetooth Peripheral device drivers are not installed. (code28)
Good day to you, Sir I USE THE SONY VAIO VGN - CR 37GN, I HAVE THE DRIVERS FOR BLUETOOTH PROBLEM DEVICES ARE NOT PROPERLY INSTALLED AND CODE IS 28 CAN YOU ME DO CERTAIN THINGS TO SOLVE THE PROBLEM THANKING YOU EMMANUEL
-
I accidentally burned some photos on a disk already on her vacation photos. the photos are now removed the disk and I have no other copie.s have I lost forever. Please help me. my girlfriend will be happy