Is a Windows XP pro 32-bit is supported by the motherboard ASUS P8Z68 - V LX with an Intel i3-2000?

Similar Questions

• Windows 7 Pro (64 bit) has no install the AHCI Driver

  When I built my current computer system in May 2011, I have not encountered this problem with installing 64-bit Windows 7 Pro on the new 500 GB Western Digital HARD drive.  In fact, I installed Win7 three times (to wipe the drive with DBAN after the first and second installs) before I was satisfied with the third installation.

  Before the first installation, I configured the BIOS of card mother Gigabyte GA-890FXA-UD5 (Maj) SATA AHCI (with SATA 3.0) and copy the driver AHCI of CD Gigabyte on a SanDisk Cruzer USB (4 GB).  The GA-890FXA-UD5 (revision 2.1, version of the F6 BIOS) has an AMD chipset.

  During each installation, the Win7 Installer reported that she could not find a HARD drive and offered the option to load a driver.  I used this option, and the installation program displays a dialog box with whom I sailed the Cruzer to select AHCI driver.  Each time, Setup loaded the driver with success smoothly.  Of course, I still have the installation of Microsoft Windows 7 Pro DVD, purchased with a full license of the retail.

  Example: two years later, after that I started to meet various problems for which I could find no cause, no resolution, I suspected malware or corruption of the registry.  To make a long story short, eventually I decided to erase the internal HARD drive once again, after you save the data files on an external USB HDD.

  Win7 Setup now follows the same routine, of course.  Except that now, it will fail to load the driver AHCI of the SanDisk Cruzer (!).  I've also removed the Win7 installation DVD, loaded the CD Gigabyte, sailed to the driver and selected.  The Win7 Installer is always not load.  In addition, before you run the Win7 Installer for other attempts, I connected the USB HDD external and sailed to a copy archived AHCI driver on it, but Win7 Setup could not load.  I have made many and repeated attempts, with all the storage media at hand, that contains a copy of the driver AHCI files, but not joy.

  For what it's worth, I also ran the software on the repair disk I did shortly after installing Win7 Pro, and he couldn't load the driver AHCI of the SanDisk Cruzer with CD Gigabyte, respectively.

  Then I reconfigured the BIOS of the motherboard to SATA IDE (with SATA 3.0) and rebooted the system.  You might think that Win7 Setup would have a suitable driver for the AMD SATA IDE, since she has one for the reader to optical disc Samsung DVD-Writer (obviously), but it did not find a HARD drive.  Then I sailed in the appropriate driver AMD x 64 on the CD of Gigabyte IDE files, but Setup cannot load it, too.

  Question: why Windows 7 Pro 64-bit Setup does not install the driver AHCI, and what can I do about it?

  Hello

  Thanks for posting your query on the Microsoft Community.

  AHCI (Advanced Host controller) makes the NCQ (Native Command Files) with connection to warm or hot swapping through host controllers SATA Serial - ATA possible; Vista was the first to offer this feature. The problem with AHCI is that it must be enabled in BIOS before the installation of the OS. After installing the operating system will disable the PC. The reason why Windows disable the AHCI drivers not not needed during installation.

  I suggest you activate the AHCI after installing the operating system if you already enable AHCI in the BIOS, when you installed the operating system.

  Warning: This section, method, or task contains steps that tells you how to change the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  322756 (http://support.microsoft.com/kb/322756/ )
  How to back up and restore the registry in Windows

  1. in the window for the start menu search box, type regedit, click with the right button on the entry, click run as administrator, enter your credentials of the user for the UAC prompt, and then click Yes to Open regedit.
  2. in regedit, navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services.
  3. in the left pane, click msahci, in the right pane, double-click Start to change.
  4. in the window that opens, change the value to 0 (zero), and then click on OK.
  5. in the left pane, click on iaStorV (if he), in the pane, double-click Start to change. Repeat step 4and continue with step 6 below.
  NOTE: From: Error Message Occurs after you change the mode of the boot drive SATA
  6. close the registry editor.
  7. now you will need to reboot the PC and go into the BIOS and enable the AHCI. When Windows starts, it will finish installing the AHCI drivers.
  8. you will need a final restart to complete the process once the drivers are installed.

  We hope that this information helps to let us know the State of the question, we will be happy to help you.

• Windows 7 Pro 64 bit and slow down the performance of the system

  Its week Tuesday I had to buy a new motherboard for my computer as a (ASUS M5A97 THE R2.0) upgrade from my old Board that was used at the time. At present, I suffer from these setbacks and problems that I don't understand completely at all on the right, or what reasons is causing my system to the right way to work. From this moment everything that I know, is installed correctly with all the appropriate drivers (x 64) are also installed for the chipset on the map, the video card (XFX Radeon HD 6770) as well and nothing else that needed to be installed at the time because the operating system running the version of Windows 7 Pro 64 bit. The problem that I'm facing here is that for some reason, my system is now slowly in response to any kind of program or an application (either Internet Explorer, Windows Update). I have flashed the BIOS and there now the most recent version, and the system is upgraded to SP1. Any ideas?

  Good so I found the problem. It was real HARD drive I had in my system. After you told me to do what you had posted, I started thinking and wanted to try a theory. I connect a spare hard drive I had in another computer, I like a build up of hobby. It's only 200 GB, but still more than enough. Anyway, when about and installed the operating system on it and of course I could tell a MAJOR DIFFERENCE in the overall performance!

  The original HARD drive that is a Western Digital 500 GB took more than 2 1/2 hours to install completely; the Seagate 200 GB took only 20 minutes! In addition, I have much better overall system stability. So for now I'll stick with the smaller drive, until I can get a HARD drive more be my main in my system.

• Windows 7 Pro 64-bit not start after the first update.

  Integrated system:

  Motherboard: Version of the BIOS Gigabyte GA-X58A-UD3R revision 2.0: FA

  CPU: Intel Core i7-930

  Memory: 6 GB Corsair PC3-12800 DDR3 Triple channel

  HD: Western Digital Black 500 GB SATA 3 Gb/s

  Water cooler: Corsair H50

  The operating system has been installed and running perfect. Readers for the mobo has been installed and and all is well. I can see everything on my computer, network, disks, programs, Device Manager and etc.

  First update for the system, only the important updates were downloaded and after the reboot, the system will not start. The system to start repairing the system but found no problem and restart again and return to the screen of system repair.

  The operating system has been installed 5 times and I had the same problem after the first update, the system unbootable. I tried to boot from the Windows dvd, but I had the same problem again.

  Can someone help me with this problem?

  Thank you

  M. Vilela

  Hi Danielle,

  In addition to the suggestion of Rock Star, you can try the following steps and check if it helps.

  Step 1

  You can first try to start the computer in safe mode and check if you can boot to the desktop. Access the link below and follow the steps to boot to the desktop. To boot to the desktop in safe mode keep tapping key F8 during restart. Once you see the option to start in safe mode select and press to enter.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2

  If you are able to boot to the desktop in safe mode, you can access to view the history of update on your computer and search for the error code and the updates that failed to install and post it back.

  To view the update history, follow the steps below:

  A. open the control panel (all items view) and click the Windows Update icon.

  B. click on the link to view update history.

  To view the details of a single Windows Update. Select and right-click on a Windows Update list, and then click details.

  Step 3

  I would say also allows you to perform a system restore in safe mode to see if you can restore the computer to an earlier date when it was working fine.

  To restore the operating system to an earlier point in time, follow these steps:

  a. Click Start, type system restore in the search box and then in the list click on the system restore program.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  b. in the System Restore dialog box, click on choose a different restore point and then click Next.

  c. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  d. click Finish.

  The computer restarts and system files and settings are back to the State they were in when the restore point was created.

  Access the link below to learn more about how to repair the operating system and how torestore configuring operatingsystem to a point in time earlier in Windows:

  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Installation of Windows XP Pro on a new configuration of the motherboard. Installation locks a blue screen during the installation of devices. Assistance from ms said why, but not healing. Anyone know an answer?

  My old motherboard gave the soul, and I have now installed a Gigabyte GA-880GM-UD2H with an AMD Phenom 6 processor and 4 GB of RAM.  The 2 HD is a Maxtor Sata 1 300 GB ones. One is divided into 2 equal partitions, the other has a single partition. During installation, it hangs at a blue screen during the "installing devices" and towards the end of the indicator. Removing everything except the essential, makes no difference.
  With 0x0000000A IRQL_NOT_LESS_OR_EQUAL error message States. This rising on the MS, it indicates:-stop this message indicates that a kernel-mode process or driver tried to access a memory address in which he was not allowed to access. The most common cause of this error is a bad or corrupted pointer that refers to an incorrect location in the memory. A pointer is a variable used by a program to designate a block of memory. If the variable has an incorrect value, the program tries to access memory that it shouldn't. When this occurs in a user mode application, it generates an access violation. When it occurs in kernel mode, it generates a STOP 0x0000000A messages. If you encounter this error during the upgrade to a newer version of Windows, it could be caused by a device driver, system service, a virus scanner, or backup tool which is not compatible with the new version.

  I start with new parts, except the DVD & HDs drive and with a start-up Virgin & installation process. I'm not upgraded to the BONE, that's the one I was using before the reconstruction. The supplier of components, suspected of defective parts and cooperated in the provision of a set of replacement of parts, but there is no change in the problem.

  Can someone explain what I can do to start?   Thank you!

  Hello

  See the article below which might help you.

  You receive an error message "Stop 0x0000000A" in Windows XP
  http://support.Microsoft.com/kb/314063

• Unsupported personality: PCL on print Laserjet 1012 from Windows 7 Pro 64-bit

  I have an HP Laserjet 1012.  My PC has Windows 7 Pro 64 bit.  I used the Laserjet 1015 PCL 6 drivers.  When I printed the first two times, it worked fine.  Now each page just print "Unsupported personality: PCL ' at the top.

  What should I do now?

  Thank you for your ' Experts for a day Tech Support.

  Mark

  Hi rbarbo43,

  I found the following thread that will help you during the installation of the printer in Windows 7. Let me know if you need assistance?

  http://h30434.www3.HP.com/T5/printer-networking-and-wireless/LaserJet-1012-driver-for-Windows-7/m-p/351356#M16114

• HP Photosmart 3210 will not install on Windows 7 Pro 64 bit.

  HP Photosmart 3210 will not install on a brand new desktop running Windows 7 Pro 64 bit.  I downloaded the latest software, and when I run it, the installation window disappears shortly after it starts.  No error message.  I ran into several related issues lately.  I can't install a ScanJet 5590 on a new laptop running Windows 7 Pro 32-bit.  Said it ends, but nothing is installed.   Could the fact that there are other HP printers installed on these computers (network printers) installed using driver only before attempting to install the software cause problems?  I spent hours trying to solve these.

  OK, much better progress!

  If the software is always installed, tell him you'll connect later.

  Go to devices and printers, look for the printer here, make sure you that no documents waiting to print and delete the printer if it is there.

  Then go into Device Manager and remove all photosmart series 3200 drivers you find, you may need to click displays hidden on the view menu.

  Thirdly, go back to the devices and printers. Select another printer, as the writer XPS comes with Windows. Along the top, with adding a device, add a printer, print server, you will see properties. What to choose and go to the tab drivers. If you have the HP drivers in there you do not, select them and choose delete and "delete the driver only."

  Now restart and go to your Start menu and your HP folder. You must have installed the software, just no device driver, select "add a device" or "printer setup and software." Installation should complete without problem.

  One last thing, you must temporarily turn off firewall and antivirus installation, in which case he mistakingly tries to block the attempt to install.

  Good impression!

• Looking to download a 64-bit Microsoft Virtual PC version that works on Windows 7 Pro, 64-bit operating system.

  From what I've been able to 'collect', Microsoft Virtual PC may not be compatible with 64-bit operating systems, but if it is true, that I can't seem to find a version of downloadable copy of 32-bit that I can install on my HP Pro Book G3 450 who will install properly & appear in the "Programs and features" section of the control panel possibly listed as: "Windows Virtual PC.

  NOTE: my laptop operating system is: Windows 7 Pro, 64 bit.

  All the tips useful on this topic will be useful, & thanks, Chris Canfield.

  Microsoft provides two specific versions, Windows Virtual PC 32 and 64 bit for PC running Windows 7 32 or 64 bits respectively.

  https://www.Microsoft.com/en-US/Download/details.aspx?ID=3702

  You can use the 64-bit package to install and run 32 and 64-bit operating systems.

  Windows6. 1 KB958559 - x 64 - RefreshPkg.msu

  But you must install the package of law for your architecture.

• Error installation Windows 7 Pro 64 Bit OEM

  Dear all,

  I just confused with install windows 7 Pro 64 Bit OEM CD to the client PC and activate it already.

  I want to change it with Windows 7 Pro 32 Bit OEM CD(I have the cd and license) and activate it.

  The question is:

  1. can I reinstall Windows 7 Pro 32 Bit OEM CD and activate it?

  2. What is the license of Windows 7 Pro 64 Bit OEM? can I re use or sell to another customer?

  3. the procedure for my problem?

  Sincerely,

  Johan Effendy

  Dear all,

  I just confused with install windows 7 Pro 64 Bit OEM CD to the client PC and activate it already.

  I want to change it with Windows 7 Pro 32 Bit OEM CD(I have the cd and license) and activate it.

  The question is:

  1. can I reinstall Windows 7 Pro 32 Bit OEM CD and activate it?

  Answer: Yes

  2. What is the license of Windows 7 Pro 64 Bit OEM? can I re use or sell to another customer?

  Answer: No, once that you install on the customer's PC's linked to this PC / motherboard. There is a small chance that if you have another exact and model PC as the client, it "might" work.

  3       the procedure for my problem?

  For the 32 Bit just activate as you normally would.

  For the 64-bit version, you can try if installed on a similar PC phone activation.

  How to activate Windows 7 or Vista manually (activate by phone)
  http://support.Microsoft.com/kb/950929/en-us

  1) click Start and in the search for box type: slui.exe 4
  (2) press the ENTER"" key.
  (3) select your "country" in the list.
  (4) choose the option "activate phone".
  (5) stay on the phone * do not select/press any option * and wait for a person to help you.
  (6) explain your problem clearly to the support person.
  (7) the person must give you a confirmation ID, copy it down on paper,
  (8) check that the ID is correct in reading the support person.
  (9) to enter the ID number, then click 'Next' to complete the activation process.

  Activation and registration of a Microsoft product
  http://support.Microsoft.com/?kbid=326851
  Windows activation: (888) 571-2048
  (888) 725-1047 or 800-936-5700

  J W Stuart: http://www.pagestart.com

• Networking Windows 7 Pro 32-bit or 64 - bit

  My Windows 7 Pro 32 bit computer cannot access the computer of Windows 7 Pro 64 bit.  The convenience store said to ensure that the same router software is installed on both computers.  How can I check this?

  Hi Tom,

  According to the description provided that you are not able to connect to the 64-bit Windows 7 computer.

  Answering these questions that could help us to provide the best solution:

  1. What is the exact message displayed by the troubleshooter?

  2. what exactly happens when you try to connect to the 64-bit Windows 7 computer?

  3. how exactly you are trying to access the 64 bit Windows 7 computer?

  Visit this link and check:

  There are a number of reasons why you can't connect to other computers on your home network, or you can't share files and printers with them.

  Why can't I connect to other computers?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-other-computers

  Provide us with more information on the question for you more help.

• using Laserjet-Canon LBP 1120 printer on new HP ProBook 4350 s under Windows 7 Pro (64 bit).

  Hello everyone, I have a printer Canon Laserjet LBP 1120, I try to use via the new HP ProBook 4350 s under Windows 7 Pro (64 bit).  I tried the recommended troubleshooting options, nothing helps... Any suggestions?  Thanks a bunch

  All drivers/software from the Canon site, if they have win7 64 bit software and install according to Canon intstructions

• Why I can't install downloaded Acrobat XI Pro on Windows 7 Pro 64 bit.

  Downloaded Adobe Pro XI. Will not install on my Windows 7 Pro 64 bit pc. Get the message stating that the program is 32 bit and not compatible. I can only assume that the exe tries to load Acrobat in the folder 'Program folder' of 64 bits, and not the "Program Files (x 86)" folder for 32-bit applications. What can I do? Try to download another? Download the trial version and use the serial number that I got? If I can force the exe file to load in the (x 86) folder? Appreciate your help.

  Thank you both for responding. Solved the problem with the Online Chat Help. Re-uploaded the file from Adobe (essentially the previous suggestion of the post, but not the trial version). Agency of Online Chat stayed with me through the download, installation and launch the program. Best estimate is that the initial download has been altered somehow. All right.

  Joe

• ASUS VS247H 23.6 "LED LCD, is detected by the generic devices such as 'PNP monitor' Manager My video card is detected correctly. Win 7 Pro 64-bit. It also shows that Asus VS247 in devices and printers

  This monitor works fine but is detected by the generic as 'PNP monitor' Device Manager. My video card is detected correctly. I am running Windows 7 Pro 64-bit. It also shows that Asus VS247 in devices and printers. I checked the Asus support and they do not have a monitor driver.

  Any comments would be appreciated.

  Roger,

  I'm glad to hear that.

  Just to let you know, it is often the case with the monitors.

  They will be the "default"setting, but still have the correct driver.

  Happy computing,

  B Eddie

• Aurora running, but can not be played on Desktop Windows 7 pro 64-bit

  I've been using Aurora for several years with Windows 7 pro 64-bit with the two latest major 28/29 Auroa just missing from my desk after clicking on the icon on the desktop, I tried to uninstall, but the system told me I had still Aroura running uninstall so I had to reboot my PC, I could uninstall I then reinstalled Aurora and a pinned icon appeared in the taskbar, but when I clicked on the icon on the desktop the hourglass turned but no Aroura started on the desktop, so I went through the whole thing again and uninstalled Aurora and installed Firefox V26 and now it has progressed to the last version that has disappeared as exactly the same way.

  What can I do if I use Aroura again because it is very good and safe to use?

  I can't use the troubleshooting info as I can't see Aurora/Firefox to view or copy/paste the info shown.

  Pete

  Thank you solved the problem, I restarted the PC and now Aurora works again thanks.

• Maximum memory for Pavilion DV7t special edition running Windows 7 pro 64-bit with Intel i7 Q720

  I have an entertainment 2009 Dv7t Special Edition running on Windows 7 64 bit with intention processor i7 Q720 @1 .60GZ. I have 8 G of ram now but need to go to the top. Can I put two 8 G in the slots. Read some reviews say the software works and Windows 7 pro 64-bit can take up to 132 G RAM, if that was even possible. I run two internal drives. But with the addition of the cloud and running photoshop on cloud too much memory is used, slow down the computer. You want to go to 16. Everybody does and no problem?

  Thank you

  Hello

  As mentioned previously, there are SEVERAL dv7t editions and special editions. We have dv7t-3000, 4000-dv7t... and it is very difficult to find the right plug. Please use the following link to find the product/model number:

  http://support.HP.com/us-en/document/c00033108

  Your machine could be the following:

  http://h10025.www1.HP.com/ewfrf/wc/manualCategory?cc=us & dlc = in & lc = in & product = 5292645 &

  If so, the #4 on the following manual page it support 16 GB max:

  http://h10025.www1.HP.com/ewfrf/wc/manualCategory?cc=us & dlc = in & lc = in & product = 5292645 &

  You can have 2 x 8 GB, no choice. Only a few portable computers that have 4 slots and supports up to 32 GB. No way on this earth at this time, you can find a laptop that supports the 132 Gb of RAM.

  Kind regards.