is open dvd

Similar Questions

• Pavilion s5-1234: button s5-1234 Pavilion not not opening DVD player

  A customer brought me a Pavilion s5-1234 with a dead hard drive to be replaced. I replaced the drive and ready to reinstall the OS, but pressing the eject button on the front panel has nothing. I was able to open the front cover and press eject directly on the drive manually and it works beautifully.  I can't see any type of mechanical connectivity related to the button from the front before activating the drive, so I'm puzzled as to why it does not work. It is obviously the original DVD drive that came with the unit.

  Any suggestion would be appreciated.

  Too bad, people!  The cable of the activation of the switch of the Panel front and DVD player had been disconnected when you remove the hard drive.  I missed it when he put it back together.  Once connected, all is well with the world!

• I:\ is not accessible .__Incorrect function___and in the other CD as__Blank that allowing open, DVD RAM, changing to CD player by inserting a correct DVD.

  System configuration: Windows XP with SP3 (Original) and all other Microsoft updates. An engraver of DVD from LG (HL - DT - ST DVDRAM) - SATA & Samsung DVD writer (TSSTcorp CDDVDW SH-S222A SCSI) - PATA later do IE August 2010 & September 2010 with the latest firmware, Nero 8.

  On a previously written DVD Insert, complete correct IE fully functional in other dvd burners / rom, DVD RAM icon changes to CD with two blank CD showing player one and not accessible with the message above in the other happening too the DVD-RAM to CD drive.

  Not understand, reported the problem to the company service centers assuming failed drive to be replaced during the warranty period. Provided with other drives of different model but unfortunately same case again. Searched the Internet, consulted and I have tried all sorts of remedies, but without success. Although all CDs, written or purchased fully functional, only previously written DVD.

  Then tried the solution of Microsoft Solution Center as "Mats_Run.dvd". Same here as that 'Please insert media readable by the CD/DVD drive [I:].  Windows tried to open the CD/DVD drive for you. "and finally as ' media in the CD / DVD drive is not readable (TSSTcorp CDDVDW SH - S222A SCSI CdRom Device' with the status"not set".)

  Wasted a lot of money and time behind this problem try this this, but without success. So looking forward to you for that my major problem not identified as an emergency like with me for needing to use these data. Again, no problem at all on my side of the machine and quality DVD that are required to access. And kindly, as soon as possible. Thank you.

  Lately, just after the announcement of this problem, insert a blank DVD to check DVD writing. And yet even ONCE - DVD RAM changing to CD player in both and in the above statement PATA and SATA a blank CD. Sense DVD is not reading as well as writing. Please add this also.

  Hi Sreeparno Baksi,

  Try the methods below:

  Method 1:

  Uninstall Nero 8 on your computer. You can check the link that help you with the steps to uninstall program to add or remove function below: how to change or remove a program in Windows XP: http://support.microsoft.com/kb/307895

  Method 2:

  Delete manually the filter upper and lower filters from the registry editor. See: (Section: fix it myself: your CD-ROM drive or DVD drive is missing or is not recognized by Windows or other programs:http://support.microsoft.com/kb/982116 )

  See also the link below: Advanced Troubleshooting for issues that occur when you are installing a new CD or DVD drive in Windows XP: http://support.microsoft.com/kb/314096

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• used open DVD player and is not detected by my computer or Device Manager

  Portable Hi, im having a problem with my dvd player, it worked fine, then I stop my computer one night, woke up the next day, tried to open my dvd drive but it used open... so I checked my computer and it has not been detected there, so I took the next step and active Device Manager... it has not been shown here either ive deleted filters upper and lower, but nothing works, I still have to check the bios because im not sure 100% what to look for or even how to check the bios, Ive only had my laptop a year and keep it in good condition... I hope it's a software problem and I don't have to send it for repair.

  any advice would be appreciated

  OK, I tried the sfc/scan command prompt now he got 77% and said that he could not perform the requested operation, I'll try a few more things you have posted and get back to you with the results

  Thanks for the help.

  I took your advice and tried Panda antivirus so far its adware found one, an attepmts of two Trojans and blocked to high jack my wifi connection, it's much better than my old av that has not detected any of these things!

  OK I just finished trying all the checks you mentioned... but nothing helps, looks like it's a hardware faliure after all, well.

  Thanks for the help anyway.

• I tried to burn some pictures with music on a DVD using Windows DVD maker, but others cannot open or run the disc. I tried to use DVD-R and DVD + R, but nothing works. Any suggestions?

  I have created a slideshow with background music using Windows DVD maker on a DVD-R and DVD + R and others cannot open or run the disc. I can't run into a DVD player, but my computer it plays very well. Any suggestions?

  Lol it won't play in my DVD player either. Just the computer.

  =====================================
  This could be a hardware problem with your DVD writer
  but here's something you can try.

  Create your slideshow (photos and music) in the film
  Creator of... and then publish the file to a folder on your hard drive
  walk in the .wmv format.

  Windows Vista
  Getting started
  Windows Movie Maker
  http://Windows.Microsoft.com/en-us/Windows-Vista/getting-started-with-Windows-Movie-Maker

  Windows Vista-
  Publish a movie in
  Windows Movie Maker
  http://Windows.Microsoft.com/en-us/Windows-Vista/publish-a-movie-in-Windows-Movie-Maker

  Then try to use the following free software to burn your DVD:

  (FWIW) It's always a good idea to create a system
  Restore point before installing software or updates)

  DVD Flick
  http://www.dvdflick.NET/

  Be sure to read the Guide:
  http://www.dvdflick.NET/Guide.php

  If you have problems to download DVD Flick...
  Try the following direct link:
  http://tinyurl.com/yzx9sck
  or...
  http://downloads.sourceforge.NET/project/dvdflick/dvdflick/DVD%20Flick%201.3.0.7/dvdflick_setup_1.3.0.7.exe?use_mirror=SoftLayer

  Save the file to a folder on your hard drive and
  install from there.

  Tutorials:

  Tutorial DVD Flick
  http://beginwithsoftware.com/videoguides/DVD-flick-Guide.html

  Burn any Format video DVD PC
  http://www.freevideoworkshop.com/dvdflicktutorial.htm

  To create a video DVD base that should play in a free
  permanent drive DVD... try the following...

  Good luck.

  First... read the DVD Flick Guide to familiarize
  with the program.

  Open DVD Flick and insert a blank DVD in your drive.

  If the window of Autorun from your computer... just close it.

  Click the project settings button and check... Video /.
  Target format... residents United States... Choose... NTSC /.
  Accept.

  The title button left click Add and navigate to your
  Video clips and select the ones you want on the DVD.

  You can have by selecting one and then use
  the up and down buttons.

  Left click on the button create DVD / OK / Yes / Yes.

  Please wait while the DVD is created.

  When the text "Completed successfully" is displayed you
  DVD Flick can close. Now you can eject your DVD
  and play in your DVD player.

  At some point you might want to buy more
  Advanced Cyberlink, Nero, Roxio, software
  Ulead, etc... but at least it is a start.

  Good luck.

  John Inzer - MS - MVP - digital media experience

• Satellite A50-109: manages the CD but not DVD player

  Hello

  I write from Türkiye.
  I have a problem on dvd rom. My dvd - rom can open the CD but not open DVD.
  What can be the problem? Can you help me please?

  Thank you very much right now...

  Sorry, but your ad does not give us enough information for a better understanding of the problem. You mean what DVD? You write about the original DVD movies or some created cottages, films, copies or what?

  Please test with different content (movies, the saved files and so on) and let us know exactly what is happening.

• 23 Pavilion: Pavilion 23 dvd

  I tried to play videos on my Pavilion 23 Office all-in-one running Windows 8 and nothing happens. What are the steps to fix thios dilemma? Please

  Hello

  Your machine must have a software called Power DVD or a similar name. Please try:

  b press Win key then pree Q.

  (b) type power... on the search box,

  c select Power DVD (or similar) to open it.

  d open DVD and play

  Next time, you don't need to repeat the steps above.

  Kind regards.

• 27-inch Imac (2011) will play is more DVD

  It wasn't a problem, before I've upgraded to El Capitan. But having received only a few new commercial DVDs I tried to run and each time they were ejected after 30 seconds without explanation. I know that the DVD themselves are ok because work on an ancient mac laptop. When I tried a job formerly DVD, it worked but when I tried to eject it, the app froze and I had to use force them to leave. DVD player smoking but the DVD would not eject. I tried various tricks to eject it but ultimately had to do a restart. After the reboot, this old DVD has been treated as the nine. My machine does not recognize. Later, I opened the drive DVD of Launchpad, inserted the new DVD and recalled in the file menu "Open DVD Media". If it showed two folders "Audio_TS" and "Video_TS" all the files in the folder have been listed, but is not accessible. Clicking play gave me the message "the disc supported is not available" (although at this time, he showed as an icon on the desktop. Then I got the beachball dead and when I opened it the player after the force quit I was still this beachball and no further response. When I did drag the icon of the DVD disc in the trash, Finder became unresponsive and I had to restart, the DVD disc has disappeared from the top of the desk, wrapped around but does not eject. Finally I ejected it with the keyboard button. When I restarted DVD player without the drive it seemed to work, IE no beachball, so I re inserted the annoying disc and this time, it worked.

  Why am I having to go through all this palaver?

  But hang in there! as soon as I tried to play it it told me he was unaware of the damaged areas, (this plays on my laptop, however) and after a few minutes we were at the beachball. Error 69902 then reported as a DVD Player system error. Then it crashed. Not one of the 6 new DVDs that is given to me for Christmas would load or play. Now we're back to not even have an icon on the desktop and the discs eject automatically after a minute

  The issue has nothing to do with El Capitan, I got El Capitan installed on my iMac 2011 for months and have never had any problems with DVD playback. Your problem may be a dirty or faulty drive or the computer may need a simple reset. First make a few resets base as a SCM and reset the PRAM, the indications are in iMac SMC and reset the PRAM. If the reset does not work, go to your local office supply store and get a CD/DVD cleaning kit, follow the directions and clean the lenses. There are lasers for CD and DVD in the SuperDrive, one of you maybe just dirty or it may have failed. IF the cleaning kit does not resolve your problem, you will need to replace the drive. You can either get another drive SuperDrive (not recommended because of the expenditure) or you can get an external drive. If you decide to take an external hard drive I recommend contacting OWC (www.macsales.com) and they can help you to choose the one that fits your needs.

• How to burn DVDs on XP?

  My situation is:

  I loaded video files from a sony handycam, convert to wmv for use in WMM. I made movies, saved in .avi format and tried to use PMB to burn a dvd. The files show too big (11 + gb) to burn it to a dvd. Since I'm on XP, I do not have DVD maker. What are my options to get these files to a size to burn a dvd?

  Thank you!

  My situation is:

  I loaded video files from a sony handycam, convert to wmv for use in WMM. I made movies, saved in .avi format and tried to use PMB to burn a dvd. The files show too big (11 + gb) to burn it to a dvd. Since I'm on XP, I do not have DVD maker. What are my options to get these files to a size to burn a dvd?

  Thank you!

  =================================
  The software free DVD Flick might be worth a try:

  (FWIW) It's always a good idea to create a system
  Restore point before installing software or updates)

  DVD Flick
  http://www.dvdflick.NET/Download.php
  (the download is: "dvdflick_setup_1.3.0.7.exe")

  Save the file to a folder on your hard drive and
  install from there.

  Be sure to read the Guide:
  http://www.dvdflick.NET/Guide.php

  Tutorials:

  Tutorial DVD Flick
  http://beginwithsoftware.com/videoguides/DVD-flick-Guide.html

  Burn any Format video DVD PC
  http://www.freevideoworkshop.com/dvdflicktutorial.htm

  To create a video DVD base that should play in a free
  permanent drive DVD... try the following...

  First... read the DVD Flick Guide to familiarize
  with the program.

  Open DVD Flick and insert a blank DVD in your drive.

  If the window of Autorun from your computer... just close it.

  Click the project settings button and check... Video /.
  Target format... residents United States... Choose... NTSC /.
  Accept.

  The title button left click Add and navigate to your
  Video clips and select the ones you want on the DVD.

  You can have by selecting one and then use
  the up and down buttons.

  Left click on the button create DVD / OK / Yes / Yes.

  Please wait while the DVD is created.

  When the text "Completed successfully" is displayed you
  DVD Flick can close. Now you can eject your DVD
  and play in your DVD player.

  At some point you might want to buy more
  Advanced Cyberlink, Nero, Roxio, software
  Ulead, etc... but at least it is a start.

  Good luck.

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• Conversion of project movie maker Windows DVD player

  Can a project created with windows movie maker (and shown through media player) be converted so that it plays in a normal DVD player? If so, how?

  Can a project created with windows movie maker (and shown through media player) be converted so that it plays in a normal DVD player? If so, how?

  ========================================
  Yes... and since you post in the XP forum... you
  must run XP with Movie Maker 2.1?

  OK, you need to save your project in .avi or .wmv
  film format. Then you need DVD Aurhoring software for
  create a video DVD. The software free DVD Flick can do...
  (How to record in .wmv or .avi... pasted below)

  DVD Flick
  http://sourceforge.NET/projects/dvdflick/

  (the file you need to download and install is:)
  "dvdflick_setup_1.3.0.7.exe")

  Be sure to read the Guide:
  http://www.dvdflick.NET/Guide.php

  Tutorials:

  Burn any Format video DVD PC
  http://www.freevideoworkshop.com/dvdflicktutorial.htm

  Tutorial DVD Flick
  http://beginwithsoftware.com/videoguides/DVD-flick-Guide.html

  Here are some basic instructions:

  To create a video DVD base that should play in a free
  permanent drive DVD... try the following...

  First... read the DVD Flick Guide to familiarize
  with the program.

  Open DVD Flick and insert a blank DVD in your drive.

  If the window of Autorun from your computer... just close it.

  Click the project settings button and check... Video /.
  Target format... residents United States... Choose... NTSC /.
  Accept.

  The title button left click Add and navigate to your
  Video clips and select the ones you want on the DVD.

  You can have by selecting one and then use
  the up and down buttons.

  Left click on the button create DVD / OK / Yes / Yes.

  Please wait while the DVD is created.

  When the text "Completed successfully" is displayed you
  DVD Flick can close. Now you can eject your DVD
  and play in your DVD player.

  At some point you might want to buy more
  Advanced Cyberlink, Nero, Roxio, software
  Ulead, etc... but at least it is a start.
   
  Finally... Here's how to Save Movie Maker:

  To save in a .wmv movie file...
  Type of... CTRL + P to open the movie recording Wizard.
  Choose... My computer.
  Next /.
  Enter a name and a location.
  Next /.
  ICT... "Best quality for my computer.
  Next /.
  Wait while the movie is saved.
  Finishing...

  To save a .avi movie file...
  (and other options)
  Type of... CTRL + P to open the movie recording Wizard.
  Choose... My computer.
  Next /.
  Enter a name and a location.
  Next /.
  Show more choices.
  Other parameters.
  Open the window of the droplet and choose... DV - AVI.
  Next /.
  Wait while the movie is saved.
  Finishing...

  Good luck...

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• How do I see what I burn on my aloan stand home dvd player.

  I burned a dvd. But I can watch the dvd on my computer, but not on my reader dvd standaloan. It gets more complicated all the time. the closest I can fill a dvd successfully, it seems to be that I'm missing. I have read the guide dvdflick and attempted to finalize my burn, but then burn IMG takes over and img burn not adopted for ntsc format. Can some a unmask for me what I am doing wrong...

  Some free-standing DVD players will not play a DVD-video made home.

  In any case... maybe the info will help you:

  Tutorial DVD Flick
  http://beginwithsoftware.com/videoguides/DVD-flick-Guide.html

  Burn any Format video DVD PC
  http://www.freevideoworkshop.com/dvdflicktutorial.htm

  AVI to DVD with DVD Flick Guide
  http://www.Digital-Digest.com/articles/AVI_to_DVD_using_DVD_Flick_page1.html

  To create a video DVD base that should play in a free
  permanent drive DVD... try the following...

  First... read the DVD Flick Guide to familiarize
  with the program.

  Open DVD Flick and insert a blank DVD in your drive.

  If the window of Autorun from your computer... just close it.

  Click the project settings button and check... Video /.
  Target format... residents United States... Choose... NTSC /.
  Accept.

  The title button left click Add and navigate to your
  Video clips and select the ones you want on the DVD.

  You can have by selecting one and then use
  the up and down buttons.

  Left click on the button create DVD / OK / Yes / Yes.

  Please wait while the DVD is created.

  When the text "Completed successfully" is displayed you
  DVD Flick can close. Now you can eject your DVD
  and play in your DVD player.

  At some point you might want to buy more
  Advanced Cyberlink, Nero, Roxio, software
  Ulead, etc... but at least it is a start.

  Good luck.

• DVD burning Info

  I tried to burn a dvd using Windows Movie Maker and DVD Flick slideshow. Unfortunately, I was cheated to achieve my goals with each attempt. I am running Microsoft Windows Professional version 2002 service Pack 3. My computer is running [R] Intel Pentium [R] 4 CPU 3 .00GHz, with 480 MB of RAM. And ATAPI CD RW 52 x 32 and the CD-ROM/DVD-ROM drive. CD-ROM standard drive HL-DT-ST DVD - ROM GDR8164B CD-ROM drive. In addition, its Realtek AC 97, audio and video controllers. My computer runs the wrong hardware to burn DVDs, or I go to write the wrong way. I have went hollow IMG burn fine and have been paying attention to the details. Do I need to use wmv or avi files? Help please!

  FWIW... the following information can help you with DVDFlick:

  WMV or AVI should work in DVDFlick

  Be sure to read the Guide:
  http://www.dvdflick.NET/Guide.php

  Tutorials:

  Tutorial DVD Flick
  http://beginwithsoftware.com/videoguides/DVD-flick-Guide.html

  Burn any Format video DVD PC
  http://www.freevideoworkshop.com/dvdflicktutorial.htm

  AVI to DVD with DVD Flick Guide
  http://www.Digital-Digest.com/articles/AVI_to_DVD_using_DVD_Flick_page1.html

  To create a video DVD base that should play in most
  free-standing DVD players... try the following...

  First... read the DVD Flick Guide to familiarize
  with the program.

  Open DVD Flick and insert a blank DVD in your drive.

  If the window of Autorun from your computer... just close it.

  Click the project settings button and check... Video /.
  Target format... residents United States... Choose... NTSC /.
  Accept.

  The title button left click Add and navigate to your
  Video clips and select the ones you want on the DVD.

  You can have by selecting one and then use
  the up and down buttons.

  Left click on the button create DVD / OK / Yes / Yes.

  Please wait while the DVD is created.

  When the text "Completed successfully" is displayed you
  DVD Flick can close. Now you can eject your DVD
  and play in your DVD player.

  At some point you might want to buy more
  advanced as Sony, Cyberlink, Nero, software
  Roxio, Ulead, etc... but at least it is a start.

  Good luck.

• I would like to know why I can't burn a dvd

  I tried to burn DVDs with windows media center of Utorrent and when I en cert in my magnovox dvd player they won't play. I would like to burn DVDs for my grandchildren to use when they go down for Christmas. I go from FLV converters and all sorts of programs that do not work for me. There must be a combonation of free software that I can use to achieve my goal of making my happy babies. I'm not rich or well offshore. But I would like to help. Thanks forume...

  FWIW... some DVD players will not play a home
  on DVD...

  That said...

  To create a video DVD that will play in a free
  Standing DVD player... you need Authoring DVD
  software.

  The following freeware can be worth a try:

  (FWIW) It's always a good idea to create a system
  Restore point before installing software or updates)

  DVD Flick
  http://www.videohelp.com/tools/DVD_Flick
  (the download is: "dvdflick_setup_1.3.0.7.exe")
  (Download from (direct link) is the fastest.

  Save the file to your desktop or a folder on your
  hard drive and install from there.

  Be sure to read the Guide:
  http://www.dvdflick.NET/Guide.php

  Tutorials:

  Tutorial DVD Flick
  http://beginwithsoftware.com/videoguides/DVD-flick-Guide.html

  Burn any Format video DVD PC
  http://www.freevideoworkshop.com/dvdflicktutorial.htm

  AVI to DVD with DVD Flick Guide
  http://www.Digital-Digest.com/articles/AVI_to_DVD_using_DVD_Flick_page1.html

  To create a video DVD base that should play in most
  free-standing DVD players... try the following...

  First... read the DVD Flick Guide to familiarize
  with the program.

  Open DVD Flick and insert a blank DVD in your drive.

  If the window of Autorun from your computer... just close it.

  Click the project settings button and check... Video /.
  Target format... residents United States... Choose... NTSC /.
  Accept.

  The title button left click Add and navigate to your
  Video clips and select the ones you want on the DVD.

  You can have by selecting one and then use
  the up and down buttons.

  Left click on the button create DVD / OK / Yes / Yes.

  Please wait while the DVD is created.

  When the text "Completed successfully" is displayed you
  DVD Flick can close. Now you can eject your DVD
  and play in your DVD player.

  At some point you might want to buy more
  Advanced Cyberlink, Nero, Roxio, software
  Ulead, etc... but at least it is a start.

  Good luck.

• When you use Windows Movie Maker, I can only burn a CD when I want to burn a DVD, why I can't burn a DVD Slideshow?

  I have pictures saved on my hard drive and I want to burn a DVD, but Microsoft Movie Maker will only burn to a CD.  How can I burn to a DVD?  I was told that it is possible.

  The only version of Windows XP that has a DVD option in Movie Maker
  is the "Windows XP Media Center Edition 2005"...

  If you want to burn a video DVD that will play in a free-standing DVD
  Drive on an XP system, you need DVD Authoring software.

  There are many choices in retail, but to get started the following freeware
  may be worth a try:

  (FWIW) It's always a good idea to create a system
  Restore point before installing software or updates)

  DVD Flick
  http://www.Digital-Digest.com/software/download.php?sid=1246&SSID=0&did=2
  (the download is: "dvdflick_setup_1.3.0.7.exe")

  Save the file to your desktop or a folder on your
  hard drive and install from there.

  Be sure to read the Guide:
  http://www.dvdflick.NET/Guide.php

  Tutorials:

  Tutorial DVD Flick
  http://beginwithsoftware.com/videoguides/DVD-flick-Guide.html

  Burn any Format video DVD PC
  http://www.freevideoworkshop.com/dvdflicktutorial.htm

  AVI to DVD with DVD Flick Guide
  http://www.Digital-Digest.com/articles/AVI_to_DVD_using_DVD_Flick_page1.html

  To create a video DVD base that should play in a free
  permanent drive DVD... try the following...

  First... read the DVD Flick Guide to familiarize
  with the program.

  Open DVD Flick and insert a blank DVD in your drive.

  If the window of Autorun from your computer... just close it.

  Click the project settings button and check... Video /.
  Target format... residents United States... Choose... NTSC /.
  Accept.

  The title button left click Add and navigate to your
  Video clips and select the ones you want on the DVD.

  You can have by selecting one and then use
  the up and down buttons.

  Left click on the button create DVD / OK / Yes / Yes.

  Please wait while the DVD is created.

  When the text "Completed successfully" is displayed you
  DVD Flick can close. Now you can eject your DVD
  and play in your DVD player.

  At some point you might want to buy more
  Advanced Cyberlink, Nero, Roxio, software
  Ulead, etc... but at least it is a start.

  If you decide to go on the road to detail... This article may
  be useful: he compares 15 of the most popular applications.

  Best video 2011, magazine publishing and software comparisons
  http://video-editing-software-review.TopTenReviews.com/

  Good luck.

• How to make a dvd using windows movie maker

  How to create a dvd with movie maker. film downloaded from camara tried to create a dvd, but it won't let me it will only do CD that I can't read on my computer or dvd player

  The only version of XP WIndows Movie Maker who has
  a DVD option is WIndows XP Media Center Edition 2005.

  You need DVD creation software to create a DVD-video...
  the following freeware can be worth a try:

  (FWIW) It's always a good idea to create a system
  Restore point before installing software or updates)

  DVD Flick
  http://www.dvdflick.NET/Download.php
  (the download is: "dvdflick_setup_1.3.0.7.exe")

  Save the file to your desktop or a folder on your
  hard drive and install from there.

  Be sure to read the Guide:
  http://www.dvdflick.NET/Guide.php

  Tutorials:

  Tutorial DVD Flick
  http://beginwithsoftware.com/videoguides/DVD-flick-Guide.html

  Burn any Format video DVD PC
  http://www.freevideoworkshop.com/dvdflicktutorial.htm

  AVI to DVD with DVD Flick Guide
  http://www.Digital-Digest.com/articles/AVI_to_DVD_using_DVD_Flick_page1.html

  To create a video DVD base that should play in a free
  permanent drive DVD... try the following...

  First... read the DVD Flick Guide to familiarize
  with the program.

  Open DVD Flick and insert a blank DVD in your drive.

  If the window of Autorun from your computer... just close it.

  Click the project settings button and check... Video /.
  Target format... residents United States... Choose... NTSC /.
  Accept.

  The title button left click Add and navigate to your
  Video clips and select the ones you want on the DVD.

  You can have by selecting one and then use
  the up and down buttons.

  Left click on the button create DVD / OK / Yes / Yes.

  Please wait while the DVD is created.

  When the text "Completed successfully" is displayed you
  DVD Flick can close. Now you can eject your DVD
  and play in your DVD player.

  At some point you might want to buy more
  Advanced Cyberlink, Nero, Roxio, software
  Ulead, etc... but at least it is a start.

  Good luck.