ISO-> boot disk problems

Similar Questions

• Satellite Pro 430 CDT - boot disk problems

  I have a toshiba satellite pro 430 cdt which I am trying to re - install windows 95 (I have win 95 on cd) on with no luck at the moment.

  I downloaded the two files from bootdisk from www.bootdisk.com, win95a and win95b, but have neither the right cd rom driver, so then I got put www.driverguide.com driver this driver on startup disk and change the config file to use the correct driver and I always get the message that no driver for cd rom drive was found.

  I don't know if the cd rom drive no longer works, even if the green light on the side flashes when you eject the disc that told me that things seem ok (maybe wrong here however). I have the cd rom plugged into the Bay on the right side of the machine (internal) and drive in the caddy it is connected on the left side of the machine (external) and even if I swap them on the cd rom drive does not work but the floppy drive works in two ways. If the connector edge on the cd rom drive doesn't work properly or the drive itself is shot.

  If I remember correctly when the boot disk works correctly it should give you 3 or 4 options (don't remember that it was a long time ago I finally did, and I did not work boot disc, DOH!), which one should be something like, "install windows with the cd rom support" or something like that.

  Once I get this I am ok I have win 95 on cd, and it is quite simple installation there from there that I built a few pc and installed different versions of windows with no true front hassels.

  Did he have the same machine as me (uk version) and able to compress all the files on a boot floppy from win 95 work and e-mail it to me?

  Or just files autoexec.bat and config.sys are all I really need (as long as they work those). Anyone know anywhere I can get my hands on one set of diskettes originally supplied with the machine that I seem to have lost mine, I think there were two or three players but no windows cd, I bought my copy (legit) from a computer fair years.

  Will provide you with my e-mail address later if necessary.

  Thanx

  Steve Jones

  Hi Steve

  I found the information that the device was shipped with 10 x player XM - 1502-B.

  Check this box:
  http://www.cdrom-drivers.com/companies/1066.htm

  There you can find a lot of drivers for different units. But maybe it's something wrong with the occupation of s PIN. In addition, you can ask the service partner for advice.

  Good bye

• Boot disk problem

  Hey guys,.

  I'm in desperate need of help! My laptop froze on me today, forcing me to hard reboot.  In doing so, he was only a folder flashing with an exclamation mark on the subject.  I tried some of the troubleshooting tips I found and held R command to force the recovery of the internet, but don't have my usual disks part of utility of disc.  All I had were 'Disc O' and 'base system Mac X', who checked properly without a need of repair.  I then tried to reinstall OS X, but it lacked all the discs for me to choose as the destination of the installation.

  What can I do to start my computer? What is a hard drive problem? IM traveling to the India tomorrow and it's a real bummer that I do not have a working laptop the night before leaving... I'll take it to an Apple Store, but I was wondering if anyone has experienced the same thing I have.  It seems that some of the issues that have worked for others have not worked for me.

  Hard drive seems to be dead but may have gotten disconnected. One of these requires a repair.

  (145099)

• Receive error message "is not a boot disk" problem when starting Vista

  I need help!  I used Ubuntu for a class exercise.  When I have finished using the bootable cd and tried to go back to Vista I get the error message "is not a bootable floppy.  Please insert a bootable floppy disk and press a key to try again...? »

  starting the PC and if you see the splash screen, immediately press "esc". You should have an option to select your hard drive. Use the arrow keys to select and press ENTER to start Windows Vista.

• installed the file ISO of ESXI 5.5.0 of trialware on a PC at home that has a memory of 8meg, installed correctly, then on reboot I get 'no boot disk was detected or the drive failed', I'm boot from the hard disk, any ideas?

  installed the file ISO of ESXI 5.5.0 of trialware on a PC at home that has a memory of 8meg, installed correctly, then on reboot I get 'no boot disk was detected or the drive failed', I'm boot from the hard disk, any ideas?

  Welcome to the community,

  Please take a look at for example http://wp.secretnest.info/?p=697 to know if this is the problem you are facing.

  André

• Problem full boot disk

  I was struck with the dreaded full disk boot error message. I have a hard disk of 500 GB solid state. Disk utility, I opened, and he said I had about 44 GB of free space. If this should not be sufficient?

  In any case, I deleted my Aperture libraries and disk utility now says I have about 56 GB of free space. So, I went about my business when I suddenly got the message startup disk is full again. I checked the disk utility and discovered that she had changed to 56 GB less than 1 GB.

  So I restarted my laptop, and it's the same thing. What is going on?

  I have a possible answer: I checked Activity Monitor and discovered that there are some very big 'process' which had to be closed by force.  It is a problem, I thought I had solved a long time ago.

  If have several websites that I have developed on my laptop. If I open a web page in a browser, and this web page is linked/included in a missing file, then the page starts blocking memory. The only warning is that my computer started acting sluggish. I then open the activity monitor and usually have to force to close a series of rogue process maybe half a dozen. But which never resulted in a startup disk full message.

  I know that a web page of thugs would use additional memory, while a boot disk error seems to indicate a physical lack of SPACE.

  Anyway, does anyone have advice? Thank you.

  Stop the web server and see if the problem stops.

  Looks like your sites consume too much memory. In "physical memory" is exhausted the operating system written unused memory to disk - this is called "paging" or "Exchange on the disk. Obvoiusly which means disk space gets reserved for this "expanded memory". Finally, something must give.

  56 GB of free space is OK, unless you have a process that runs somehow out of control like this - something not at all with these sites or scripts. Personally, I prefer a bit more margin to maneuver, but 56 GB should be enough on a healthy system.

  You don't need to use disk utility to see the use of disk space. Open a Finder window and simply get the information on your disk (Go Menu > computer lists all storage connected).

  Expanded memory must be included in the activity to the 'used Swap' monitor if I remember correctly.

  You should not kill the process either - it's a sign that something is wrong and can lead to instability and data loss if they are used by large parts of the operating system.

  I think you should work on your test pages why begin to 'blocking of memory', perhaps runaway javascript or something in the real of the server, you could read the logs from the server if they are active to see if something is do a lot of queries etc.

  What is the real server and code that you are running?

• Dual Boot with windows XP Pro with 2 HARD drive, error on secondary windows install: "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check boot path and disk hardware... »

  Hi, I recently bought a new Hitachi 1 TB internal hard drive. I wanted to do a clean install on the new drive (d), be able to dual boot my computer and leave my old 300 GB disk (C :) as the primary windows installation. After physically installing the new HARD drive, I noticed that "new hardware found" and the the brand name flashed in the bottom right corner. I thought I'd see the new hard drive in my computer, but I did not. I initialized the new HARD drive with the computer management window (right click on my computer - manage) and I also formatted in NTFS (I had to change my printer hard drive letter to assign the new HARD drive with the letter D, but I've made other changes after this step). Now, I could see and use in my main windows on the C: installation. I then installed a windows new copy XP pro with the installation CD I got for my C: but on the D: (Note: I have a Dell computer (and the Dell reinstallation CD) and my current version of windows has SP3 while the installation CD is only SP2) (I also reformatted my HARD drive during the installation of windows to NTFS)

  Now when I try to start on installing the new on my D: I get "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check startup disk and hardware access path. "and another line saying to refer to manuals HARD drive and windows.

  My Boot.ini file at this time was:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (0) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I looked towards the top of this help page, but for now I'm unlucky:

  http://support.Microsoft.com/kb/314477

  (The next steps I took by throwing from the Windows CD and go into the repair console)

  I tried to use the bootcfg /rebuild but the line to boot.ini for my secondary HARD drive still does not work.

  He gave me something like:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (1) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I also tried to change the signature() to multi (0), but it did not work. (or try almost all possible permutations of disk() and rdisk() partition() 0 to 2).

  I also tried to use expand F(dvd-drive):\i386\ntkrnlmp(I_have_a_duo-core).ex_ D:\windows\system32\ntoskrnl.exe and a few other combinations, but I when I login as D:\windows simply, it fails to extend with a message like "could not develop" or C:\windows I get "restricted access".

  I have not yet tried CHKDSK/r, but since I did a clean install on a newly formatted drive... I don't think it would work.

  I've also marked the partition on the D: as active (in computer management), but it did not help me.

  I've done a first installation of windows repair, strangely, I couldn't fix this one... Still does not work...

  My default windows installation yet works very well & I see that windows has been installed on the D: but I'm ideas from how to operate the dual-boot, can someone throw me a BONE on what to do?

  Maybe try to do something with the Boot Manager (whatever it is?) Create a new partition and use it as a boot manager? I don't really want to do this, because if I made a mistake I will be unable to use my computer and dual boot should work without going through all this trouble... But I found this page: http://technet.microsoft.com/fr-fr/library/ee829686%28WS.10%29.aspx

  Could a clean install two HDD help? I hope I won't have to do...

  Someone has an idea?

  PS: I'm not such an advanced user so I need a solution step by step, thanks!

  Edit: I also noted that I can't see my new HARD drive in my BIOS... weird... SATA-0 is my old drive HARD 1 and 2 are my dvd 3-5 readers are 'off' and it doesn't seem to be anything that it is plugged in. I also have 4 bays for internal HARD disks. Now, 2 are busy.

  Edit2: I looked inside my case and enabled the good Sata in the Bios after a reboot it detected the drive correctly. Dual boot doesn't always work well... The fact that it was disable in the BIOS while I was installing the new HARD drive could change anything? Hmm...

  In case I wasn't clear enough: I had a windows XP Pro installed on my C:, bought a new hard drive and installed the same copy of windows on it (d). I think that should allow me to double boot between the two installs different. Even if for some reason I can't boot from one on my D:. Andrew, I do not understand why you so far physically disconnect the other drive, the point of the whole operation is to build a boot.ini file so that the BIOS knows that it y facilities 2 windows and you allow to choose (and not have conflicting problems between the 2 systems), someone correct me if I'm wrong? "Expand" the part of my first post made reference to one of the solutions provided by Microsoft in the first link that I have included in my previous post (but I can't seem to work).

  In addition, it is the procedure that I followed: http://www.ehow.com/how_5950826_boot-two-different-hard-drives.html

  (except I've had the first installation already done).

  Andrew "also, once a new hd is plugged on the pc & running, most of the BIOS will place (them) as 1st priority hd, set the BIOS to do this", you mean that by installing separately from windows on each unit when the other is not plugged in, I could choose what disk to start from defining their priority in the BIOS once they are all plugged back? It's too tedious (as I intend to move frequently between the 2 installs) and requires a computer to other users of the lack of computer knowledge. Unfortunately, it is not a viable option.

  EDIT: I DID IT! Hmmm... Well, I double checked in the recovery console, the path of the new HARD drive with the arc command Scan. Tried to start again with the MULTI (0) in my boot.ini and it worked... I also had my windows install CD in. Maybe that is why I could not start, windows needs the CD to complete the installation? Weird, I don't know what I did to the difficulty it... but hey, it works! Thanks for your ideas guys!

• Problem getting all the portable versions of firefox from 28 to start without error xpcom in DO PE 48 boot disk place at the start of the P-Start

  I built an emergency recovery boot disk using MAKE PE3 - 48 and P Start to enable the use of portable programs after booting into the recovery environment. I have used with success of Firefox Portable till and including version 28.

  All portable versions since then up to the last 35 Version will not start. All display the error could not load XPCOM.

  These same portable versions of Firefox, however, will begin in the normal environment of Windows 7 Ultimate on all my computers, however, in the environment of DOING PE 3, on the same device, they will not.

  You can ask about it in the support forum for Firefox Portable here:
  http://PortableApps.com/forums/support/firefox_portable

  Firefox Portable is a 3rd party application, not published by Mozilla. I installed it myself for dealing with changes in it and how it differs from the official version of Mozilla, but don't know enough about it or something DO PE 48 to be able to help you.

• Blue Screen: Error Code C0000218(Registry File Failure) I have NO recovery disk, boot disk, etc. What can I do?

  I have a desktop HP that I installed a new hard drive on Windows XP Home Edition Service Pack 3. He has been working very well. But, the other day, I took out my DVD ROM and try it switched with different DVD - ROM, and when I restarted my computer, I got the "blue screen error Code: C0000218 (registry file failure)." The registry cannot load the HIVE (file). \System ROOT-SYSTEM 32-CONFIG-SOFTWARE or its log or alternate. It is damaged, missing, or not accessible in writing. "So, back to my main issue, I guess. How can I fiw it without any sort of disk recovery or boot disk etc... I know I could probably go buy some sort of recovery software, but can't afford it right now. Can someone help me, please?

  You have all the Norton/Symantec products installed and if so, do you know which ones and versions?

  You start with a chkdsk/r from the XP Recovery Console.

  Here's how:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that may have come to a store to purchase the system.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• ERROR: no boot disk was detected or the disc has failrd

  HP ENVY h8-1534pc with windows 8.

  error: no boot disk was detected or the drive failed.

  tried to run the recovery cd ROM even error. No cd or hard drve no indication in the boot order.

  out of resources

  Hello! Here are a few responses from members of the forum about your problem. See if you can find a solution from them. http://h30434.www3.HP.com/T5/forums/SearchPage/tab/message?filter=labels%2Clocation&location=Forum-Board%3AOSandSW&q=no+boot+disk+has+been+detected

  Dokie!

  PS It doesn't look good for me. Good luck and thanks for posting back.

  It has been my experience in the past that a message as this means that either the operating system is corrupt or your hard drive is dead. If your hard drive does not show in the boot order, it's a major sign of a bad HD, but not100%.  There are several free testers HD. Most have the back, which means that you don't have to have an operating system to start their. If you are not able to test your HD with F2 or F11 functions, try one of them. You will need to burn an ISO to a CD file.

  http://pcsupport.about.com/od/toolsofthetrade/TP/tophddiag.htm

  PS2 there may be answers best of the latter. Weekends are slow at times. I'm still slow

• Mac 27 inch cant find HD boot disk won't boot

  My imac starts with chime bar and apple but takes almost a day to get to the user login page and when that happens it goes no further. I can't find my HD drive icon start-up and im not sure if I still have el capitan os x 10.0 do not know what is happening? I have the 4 TB WD dou upward by car and do not want to lose all my logic projects so I guess I need boot disk and os x help if someone can thanks yall

  Your machine likely has a failed hard drive or some other problem. Please, take it to your local Apple Store or the service provider authorized Apple to be looked at.

• make a boot disk

  I'm doing a startup disk, a boot disk.  I have several disks usb, 1, 2, 3 TB, or I could use a flash drive, if he stands on a 32 GB flash drive, that is.  I suppose that it wouldn't be as people online sell everywhere to help people who find it difficult to install el crapitan.  Many of them must be as one of the amazon sellers showed 4000 available: 39 left.  Ouch.  I can't el crapitan to install to save my life.  It crashes, never works.  The importance of the support of apple is suggesting that I say 'Yes' when I start, as I have to "accept" the agreement from apple before, even though I told her is not the problem, she sent me a book of instruction page three on how to start el crapitan and to proceed with the installation, you have to say yes, and you will need to acceptt their agreement.  Yes, I did.  no problem with this part.  but it's that the things she and the two girls before and both were subsequently in the same boat.  Mr President, let me send you instructions on how to download it.  "No, I say, I did.  Do you really think someone is struggling to push a button that says "download?  Obviously, Yes. because she sent me instructions, once again, no joke, on how to push the button so he can 'download '.  Complete with how to do it with your finger and how if you have a plug in the mouse, with a separate section if you have a wireless mouse.  Hell me silly.

  O.K. HELP!  El CRAPITAN won't complete the upgrade process.  Please tell me if it takes normally 8 to 12 hours on your systems.  I guess he was hanged and killed the process.  rebooted, retried... same thing.  anything after 12 hours or more.  Yes, I used the pad on my Apple Macbook Air 11 '', i7, 4 GB ram, 250 GB SSD.  I do not use a wireless mouse.  I have not used a wireless mouse.  I did no harm to press download, and after I did, it succeeded because it was changed to read "DOWNLOAD"... "If there are employees of apple here who have not... so much worse.  If you work for Apple, leave, just freaking leave I have no more time or patience for you.  Just trust me the O.K. FREAKING the COMPLETE DOWNLOAD.  O.K.?  Because it gives an error message when I tried to install from the same disk.  Then I tried to install it from a second disc, a key USB WD 3 TB.  Seems to hang.  (Tell me whether I should WAIT WAIT 15 HOURS OR MORE for the thing to check.)  Anyway, it does not work.  So I found a TON of entries, some are already selling thousands of them, for small usb thumb drives flash of various sizes, called the STARTUP disk, so...

  I guess el Crapitan must be installed on a PARTITION AMORCABLE where in the CAR.  Something that it would have been so freaking sweet if they would have SAID THAT SOMEWHERE some TIME no matter WHEN IN THE DESCRIPTION OF THE PACKAGE ON THEIR SITE.  OK, so I think I ned a diskette formatted in some way.  Me color cheap, stupid, whatever.  But rather than buy on online at Amazon, I thought how hard can it be?  I can do it.  Big mistake.  Create a disc a disc of starting, or bootable used to be in the old days an easy as pie thing...

  However the Apple support site, helps him terminal programs, man pages diskutil, the program Apple accessories disk utility supplies, NOT HAVING ANY HELP DRIVE of FILES THAT BOOK REFERENCE, START UP DISK or any combination of the same, you know... How can you, how can you do a... whatever.  nothing. isn't there.  And here, in the consumer help pages.  No messages that are either.

  It's not rocket science.  It can be done.  How to make a boot disk?  How to format a disk a bootable floppy.  or a book drive, no matter what.

  And if y ' All are Apple support staff, and if you tell me that I pressed the wrong download button or I pulled the single button in the wrong order... I take my mac to a shooting range and shooting it be shot to pieces and displaying it on iTunes.  And never, never, ever, buy a mac or an apple anything.  , so, this whole experience has soured me I could never do that either.

  What do you know?

  <Create a bootable OS x - Apple support Installer>

  <http://osxdaily.com/2015/09/30/create-os-x-el-capitan-boot-install-drive/>

• no boot found device, insert the boot disk and press any key

  Hello, recently tried to install Windows 10 through the Assistant Boot Camp, with the help of a DVD I bought windows. But I get an error saying "no devices found Boot insert boot disk and press a key" I tried to read and do all the patches, all offer and yet no results. Any suggestions or corrections us would be great!

  MacBook Pro mid 2012

  -i7

  Evo - Samsung 500GB SSD

  -Ram 16

  -Latest version of Mac OS x

  -L' use of 64 GB PNY flash drive

  Your Mac 2012 supported creating a USB Installer to help BC Assistant. Do not use a DVD, a USB Flash drive. Your USB drive must be a USB2 flash drive, if you choose the USB mode and you will need a Windows ISO.

  See also create an ISO image for Windows - Apple Support installation media Boot Camp .

• Try to install Windows 7 via USB, El Capitan, Macbook Pro 2011 but get this error "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

  I am trying to install Windows 7 via USB, (El Capitan, Macbook Pro - early 2011), but this mistake "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

  You cannot use a USB on Mac 2011 Installer. Please burn the ISO on a physical DVD Windows (a DVD - R Carbon SL on the rate of burning slower is better) and use it to install Windows. The file Info.plist changes only allowing the creation of USB, but does not fully support a USB Installation.

• ENVY h8 - 1520t: error: no boot disk was detected or drive failed.

  Yesterday, when I turned on my computer, it was really slow and I could not open any programs. Then it went all blue and white. When I rebooted, I see "control the presence of .media, media, start the PC via ipv6, then error: no boot disk was detected or the disc has failed." I tried to hit f11, but it fills the entire screen with the error message. He died or hope?

  Looks like your hard drive has failed.

  You need to maybe replace the disk and reinstall Windows.

  Please use these instructions to test your hard drive.

  * Works even if your PC will not boot to Windows.

  If you found my answer helpful please say thank you by clicking on the icon of the thumb. If my answer has solved your problem, please mark it as accepted Solution. Thank you!