J6480 on wireless networking, but the PC can't see it
I have Time Warner cable modem with a NetGear WGR614 wireless router. Printer J6480 configured correctly - times the wireless network test report and the Network Setup page are all statuses 'PASS' or 'Ready '.
I searched the forums and found a similar problem and tried this out, his replacement cable for the bit of phone:
- Open the printer web page by accessing its IP address
- Select the networking without wire then Configuration IPv4.
- Select Manual IP.
- Enter the IP address of the printer in the manual IP address field.
- Enter 255.255.255.0 subnet mask of manual.
- Enter the IP address of the router - wireless in the field manual's default gateway.
- Select apply.
- Finally, connect the telephone line.
No luck. Note that my subnet mask is 255.255.252.0, if that matters. My PC wireless does not see the printer on the network through the Printer Wizard in one of the three options. But I can ping by IP.
Thank you!
Steve
Solved! Follow these instructions, courtesy of Chong Yip (I found his comment on Amazon.com):
Setting up a wireless connection by following the quick start guide is a huge mistake.
To avoid this problem, the best way to configure the machine is:
1. configuration of network connection in the menu of the machine, do not use the installation CD.
2. once the machine is connected, go to the menu of the wireless router config and reserve the IP address of the machine. Now, the machine will always use the same IP address.
3. install the printer driver. You can copy the installation CD to the hard drive to speed up the installation process.
4. run setup.exe, select Add a device-> via the network. Your machine must be detected by the Setup program, and you should be able glide from here.
Tags: HP Printers
Similar Questions
-
Comments see host on the network, but the host does not see comments
Hi all
I'm running Windows 7 Pro as host and have XP as a guest. I set up a new virtual network (as I saw in another post here) and made sure both host and guest get correct IP addresses.
The guest can ping on the host, but the host cannot ping the prompt. I even moved the new VM adapter above the other ones on the host and which still got nothing.
Any thoughts?
Thank you
Craigbert
> Any thoughts?
Firewall settings? (turn off for tests)
Is it time out or say inaccessible?
-
iPhone connects to the wireless router but the PC can't
HI - hoping someone can provide some answers to my problem. This happens a lot.
For some reason, the awakening of my PC it does not connect to internet or router (192.168.0.1). Restart the PC makes no difference. I have an iPhone that connects very well during all this time (via wifi, with cellular networking turned off).
This is what happens:
I go to network and sharing Center to connect:
[img src = "http://i39.tinypic.com/e031x5.jpg"]
The sky connection is to me, with an intense sound signal:
[IMG] http://i44.tinypic.com/24qn1x3.jpg [line]
He then quickly says "successfully connected to sky", although the network & sharing poster always the router as "id" and without internet access:
[IMG] http://i40.tinypic.com/ehek4w.jpg [line]
After a wait of 1-2 minutes, he moved to 'unidentified network' and without internet access:
[IMG] http://i40.tinypic.com/2qbha4p.jpg [line]
Ipconfig says:
[IMG] http://i43.tinypic.com/dgl2jm.jpg [line]
Network cards seem to be OK:
[IMG] http://i41.tinypic.com/ev5g95.jpg [line]
[IMG] http://i41.tinypic.com/210zhg0.jpg [line]
[IMG] http://i44.tinypic.com/21pt9g.jpg [line]
What I can do is to reset the router by unplugging the power for a few seconds, allowing a restart. After that, the PC connects fine and I can access the main router page:
[IMG] http://i42.tinypic.com/r28gev.jpg [line]
I don't want to have to reset the router whenever it goes well! Any help on why this is happening and what's wrong with my settings would be greatly appreciated! Thank you.
(Sorry that the images do not seem to work on this forum, but you can copy and paste; also, tips on how to show the pictures would be appreciated!)
Hello
I suggest you to update the latest drivers for the network adapter and check if it helps:
It will be useful.
-
Try to install this printer. It works via USB, but when I get to the step of configuring wireless and you're
said to unplug the USB cable, it gives me the following, not accessible DEVICE... The network configuration has been correctly transferred to the device. However, to continue to configure the network device, your Mac must have access to the device. So please make sure that your Mac has access to the network: "mynetwork" and try again.
The printer is on the network end def (I can ping ok), but the MAC can not see wireless and wont print. I've seen a few threads with similar issues and they suggest wiring the IP address in the printer setup process, but that does not work for me either. Very frustrating, any help would be great
It could be disregarded in charge of your router BT of Hello.
Let's try present first, if:
1 reboot the router to BT by pulling its plug momentarily.
2. download and install this: http://support.apple.com/kb/DL907
3. restart your Mac.
4 reset the printing system:
-Go to System Preferences > print & Scan
-Right (or control) click in the rectangle listing your printers and select Reset Printing System.
WARNING - This will remove ALL your printers!
-Select the sign more to add a printer. Select the default tab on the top of the window. Search for the printer, select it, and then beside the dropdown 'Use', select the model of the printer (not AirPrint). Wait for the 'Add' button becomes available. Until it clicks. -
I am trying to set up my wireless printer, and the printer says its is connected to my wireless network, but I can't get my computer to print wireless if I disconnect my regular network and attach the direct wireless network name, which is different and stops my internet to work. How can I get my computer to recognize the printer on my regular wireless network?
Hi @lelg,
I understand that you want to configure the printer on the wireless network. I can help you with this.
Uninstall the printer software.
Uninstalling the printer software.
Restore the default settings of the printer.
Go to Configuration, restore the default values.
Cycle power to the router and the computer.
Run the installer on the printer wireless.
Go to the configuration, Setup, menu wireless network, Wireless Setup Wizard.
Print a configuration page to get the IP address of the printer.
Select the method.
If you have a valid IP address for the printer, then try and access the Web built-in to the printer server. Type the IP address in the address bar of your web browser. (Internet Explorer)
If it loads the page from the network printer then the printer is on the network.
Download, save, and then run the installation of the software. Color HP LaserJet Pro 200 pilot M276nw MFPS.
Select your operating system, click Next and click on the software to download and install.
Test the printer.
What operating system do you use? How to find the Windows Edition and the Version on your computer.
Please provide detailed results if you're still having problems.
Good day!
Thank you. -
I have exactly the same problem in Windows Vista Ultimate Edition. I can delete, change and move all other profiles wireless network but one that reappears immediately after that I erase it.
I see that you asked initially that this issue in 2010. Has there every been a resolution?ElliottMy Eureka has been using netsh, explains Superuser.com «How to completely remove a wireless network from Vista» Everything I found on the Microsoft site doesn't give any examples on how to find profiles (netsh wlan name) or the statement appropriate to remove this profile (netsh wlan dlete name = "the name exactly as shown, case-sensitive quotes". That he solved it for me.
-
problem connecting to the wireless network, but it worked yesterday.
Yesterday, I was able to connect to my home wireless network, but not today. I also have a laptop and it connects to my wireless network, there must be something with the RT of Surface.
Home Wireless works, why can't connect?
Your post is off-topic in the forum Feedback, I moved it on the forum of "Web and Networking" Windows RT.
-
The title says it all really.
I was connected and working normally for about an hour this morning, until suddenly the connection has been lost.Windows detects the wireless network but will not connect. Two other users in the same office connect without difficulty.Help, please.Thank you.original title: vista detection network but will not connectHi JulianBeach,
1. you have made no changes to the computer before the broadcast took place?
2. What is the exact error message you get?
3 is connected to the domain of the computer?
4. what happens when you try to connect to the network?Try the steps from the following link:
Windows wireless and wired network connection problems
http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-WindowsAdditional information:
Wireless network card: frequently asked questions
http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions -
B110A connects to the wireless network but no PC connection
Hi Forum,
I just bought a new HP Photosmart B110A printer range. I got set up with my Belkin wireless router. It is successfully connected. I could set up printing webservice as well. The printer is offline and I could also print a document by sending an email to the email address for the printer configuration. This means that the printer is connected to the wireless network and the internet.
However, I can not connect to this printer from my PC connected to the same wireless netwrok. When I open the HP Solution Center, it displays the message "disconnected wireless.
When I connect the printer via USB cable, I am able to connect to the PC and impressions as well fire.
Can anyone help please?
Kind regards
Amol
Download and run this utility: http://h20180.www2.hp.com/apps/Nav?h_pagetype=s-926&h_lang=en&h_client=s-h-e17-1&h_keyword=dg-NDU&jumpid=ex_r4155/en/hho/ipg/forum/network_diag/
What did he say?
-
I'm trying to access a wireless network with the password provided for me. I get the following error message: "the network password needs to be 40bits or 104bits depending on your network configuration. This can be entered as 5 or 13 characters ascii or hexadecimal 10 or 26. "what does this error message mean and how do I address so that I can access the wireless network?
I use XP Professional with service pack 3. I get this error message every other time I try to log in to a protected wireless network security. I used to not get this message; but, now, it may be impossible, sometimes to call all wireless providers when I might only need for a short period or after hours service opening.
In addition, it is my computer that requires the network password to be different, not the provider of wireless. A password is given to me who works for other users, but my computer won't let me use it.
Hello
I suggest you to visit these links and check if it helps:
It will be useful.
-
Canon MX860 will print over wireless network but don't scan (W7 OS)
I have two laptops with XP and one with Windows 7 64 bit. Both connected to a router Wireless Linksys - internet connections well, feel very good on the two machines. The XP laptop will scan the network, but the Windows 7 laptop gets a dialog box of Scangear with this message: cannot communicate with scanner, for these reasons scanner is turned off scanner is disconnected. Have uninstalled and reinstalled all the software and drivers (with firewall disabled according to the instructions of canons), loads software successfully - but still no luck with the network scanning. Also downloaded Scangear tool - but when he's looking for the network printer, it does not. Support of Cannon says now there's an incompatibility with W7 and Microsoft can only solve the problem. Also noticed that the Canon IJ Network tool is loaded, but it does not work on W7 - new OK on the XP machine machine. Would appreciate any suggestions.
Thank you
John W
If Canon say its not compatible with win7 is something for Canon to fix and not Ms
Probably that you have installed drivers updated from the Canon site
-
Hello, when I create an ad hoc network on my laptop HP using Win7,
I can't find it in the 'manage wireless networks' (in the network and sharing Center)can you help me please?Hello
In case there are problems with your computer or it network devices check
with HP, their documentation online support and drivers, diagnostics, and
Ask problems known in their forums.Support HP & drivers
http://welcome.HP.com/country/us/en/support.htmlContact HP
http://welcome.HP.com/country/us/en/contact_us.htmlHP forums
http://h30434.www3.HP.com/PSG/==========================================
The routers are much easier and they don't cost much.
These should help:
References to Vista also apply to Windows 7.
Set up a computer-to-computer (ad hoc) network
http://Windows.Microsoft.com/en-us/Windows7/set-up-a-computer-to-computer-ad-hoc-networkAd hoc networking - how the network with the funny name can make your life easier
http://Windows.Microsoft.com/en-us/Windows-Vista/ad-hoc-networking-how-the-network-with-the-funny-name-can-make-your-life-easierHow to build a wireless network without using a router at wide band (also Windows 7)
http://www.hardwaresecrets.com/article/how-to-build-a-wireless-network-without-using-a-broadband-router/418Build a Wireless Home network without a router (also Windows 7)
http://www.labnol.org/software/wireless-network-without-router/11494/How to share files and printers on your network
http://www.hardwaresecrets.com/article/how-to-share-folders-and-printers-on-your-network/247-------------------------------------------------------------------------
Other solutions include the use of these that turn your WiFi PC into a virtual router
instead of using the ad hoc network.Connectify
http://www.Connectify.me/Virtual router
http://virtualrouter.codeplex.com/I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
Original title: Microsoft lifecam
To make a video call, the person receiving the call can not see me, but they can hear me
Hi Eddie,.
As the person receiving the call is able to hear and unable to see, we need to check if the video settings are set correctly.
Which application do you use to make video calls?
While you reply us with the above information, see the following links:
From the following link, refer to the "I can't start a video call".
Troubleshooting: Webcams
http://www.Microsoft.com/hardware/en-in/help/support/troubleshooting/webcam/LifeCam-Setup
How to make a video call?
http://www.Microsoft.com/hardware/en-in/help/support/how-to/webcam/VideoCallWith the help of your LifeCam with Microsoft Live Messenger
http://support.Microsoft.com/kb/921332?WA=wsignin1.0
Hope the above information is helpful.
-
I published my site to Business Catalyst and purchased and installation by area, but the site can be seen only with the help of a search engine. The site is seen when I type the url address, but can not find with search engines.
Hello
I suggest you sign upward to Google Webmaster tools (free) and check your site (directions are in the webmaster tools) and
also consider joining Google analytic (also free). Analytical will allow you to 'see' who is visiting your site and how they experience through research, order the seizure of the URL, or through the links, etc. Also from where they come, how much per day, etc. Lots of good information.
In addition, through this document by google
Check the performance of your site - webmaster help search
Let me know if you have any question.
-
Just downloaded book dear DW CC. ' Bought that tells me to use "Workspace expanded", but the only options I see in the button of the window or workspace are 'Design' excerpt ' and from each other. No where can I find the 'Expand' or 'Compact' that says that books are the two choices.
The book you bought is for an older version of DW. Which one, I don't know. Changed a lot in the 2013, 2014 in June and October 2014,1 releases of CC. Books are usually at least 1 version and sometimes 2 obsolete versions.
CC 13
Using Dreamweaver | Summary of new features
CC 20141
Using Dreamweaver | Summary of new features
Nancy O.
Maybe you are looking for
-
How can I create 2 albums in the same name and the same artist
The guy is anyway to make the 2 albums in the same name for the same artist? If there is no way so please someone tell me how can I suggest updating to iTunes
-
Can't the iPhone contacts not text of MacBook Pro (related to my iPhone 6 s)?
Hi guys! First time poster here, sorry if it's a matter of newb hah... but you can text with iPhone non-mac related to iPhone users? I was able to txt w / contacts that use an iPhone as well, but maintains blame on others... With the help of MacBook
-
Error property in parallel loops node
Hi all I run two screws under SP1 LabVIEW2014 at the same time and each of them contains a loop to do something. In this case a VI loop reading a control channel via the property node and the other VI makes a loop showing an empty IMAQ Image. After a
-
All, I noticed some show logfiles tech mgmt0 is down (on administratively down). Make a sh int mgmt0 also said her stockings. Is this normal? I can't ssh into the fabric IP (ip cluster and fab IPs). If the port is 'down', I'd be able to do this?
-
Flip Box with jQuery and jQuery injector
Hi! I want to integrate this feature (https://nnattawat.github.io/flip/#front) in my injector with jquery project. No idea how I can do? Thanks for your help!