label of failure of OCR

Similar Questions

• HP Pavilion 17-F122DS: laptop is dead, had failure ID

  First of all, I'm not savy with laptops, seems to be 'Magical' for me, who said: I got an error, or omission ID and don't know what to do now, he showed me this "failure ID WRONG 3: 3-78C7L8-MFPV7F-60U303 'I think it's most likely a death of a party, but what exactly? Any help is appreciated, thanks in advance.

  Hi @nrasupporter ,

  Thank you for visiting the Forums HP's Support and welcome. It's a great site for information and questions. I looked in your question about your HP Pavilion Notebook 17 - f122ds and label identification failure MAL3H3-78C7L8-MFPV7F-60U303. This error is failure of Quick Test on drive 1. What this means is that your hard drive has failed.

  I recommend the first thing you can do is to back up all your personal files etc as soon as you can.

  The laptop suffered a Jolt any? I was wondering if maybe reinstalling the HARD disk would be useful.

  Here is a link to check to see if you are in warranty. Page 35 of your manual shows you part numbers. It's the section I would use 778192-005 1 TB hard drive 5400 RPM, available for Windows 8.1 9.5 mm. Page 95 shows you how to remove the HARD drive.

  Do not hesitate tocontact us if you need assistance.

  Thank you.

• calibration Executive report failure

  Hello. I have a problem regarding the report generated by the Executive of the calibration. After a successful completion of the procedure for the PXI-5402 generator with no failure, it generates failures on the column "as left" of the results of the tests. I noticed that the low limits and high limits of the column "as left" differs from the limits "as found". is this acceptable? in the left data limits are much tighter than the data that is found as a result of the values measured for fail in the report.

  Please advise...

  Kind regards

  Laura

  Hello

  These results make sense, given that the column "As Left" is supposed to reflect the results measured after adjustment. That's why this column limits are more stringent than the column ' as found '. I wasn't aware that you were doing a check only. It's actually good that both of your tests more strict limits, which means that they held their initial calibration well enough.

  Basically, the label of 'Failure' in the column "As Left" is meaningless, unless you're of failing once you have made an adjustment to the Board of Directors. I think you're ready for the verification of the calibration stage since none of the measures ' as found ' failed. Have fun with the adjustments.

  Chris W

• Failure on label printing

  Hi, at the and of the test failure, I have the need to print the message of failure on the label. I need to print: SequenceName testName, measurement, high limit, low.

  Is there something already implemented in TestStand? What is the right approach, should I use the reminder "SequeneFilePostStepFailure"?

  Thank you very much.

  Hello

  Try to use "Parameters.Step.Name".

  Why you will not see it?  Because you go to the step of the object. and the name of the property

  For more information look in TS-help under the terms of the Index 'Step '.

  In this thread, there is a fine example of this reminder

  http://forums.NI.com/T5/NI-TestStand/repeating-a-failed-sequence-once-more/m-p/1042268

  Concerning

  Jürgen

• OCR - water bottle label

  I'm trying to do OCR to extract the water bottle label, but im not getting any closer. The water bottle label looks like the Arial font, Ive trained with the arial font characters. I tried fiddling with the settings and exposure to the light... but still not good.

  I am using the video stream, so even trying to reduce the size of the buffer but does not work...

  Any recommendations?

  Thanks /.

  Increase the image brightness and/or contrast would probably increase the accuracy of the OCR also.

  -AK2DM

• HP ENVY Phoenix 810-445qe: specifications of need on 14.79 GB "Disk 1" labelled "Datadrive1 (e).

  I spent the last few days setting up a brand new HP ENVY Phoenix 810 - 445qe I ordered from HP.com. (Information system down in the case, it may be necessary.)
  
  I did what all the new owners of the system should do after you set up the system: I did a DVD repair system, and am about to do my first image with Windows 7 (64 bit) backup.
  
  Of course, when you perform an image backup (which is like making a photocopy of your hard drive to a point in time) you can not store this backup on the same drive you're imaging, for the obvious reason that you can not write to disk at the same time you are Imaging it. If the image backup dialog box gave me three options of storage location:
  
  (1) Datadrive1 (E)
  (2) WD MyBook external hard drive (G)
  (3) Blu - Ray / DVD / CD drive (F)
  
  I was curious about the "Datadrive1" because I didn't know that's where! I don't me read something about it, then I went to control panel > system and security > ' Create and format hard disk partitions "(under administrative tools on the system menu and security - or the type of management of the computer in the Start Menu) to take a look at the drives and partitions.
  
  This computer was said to come with a SATA 3 TB and because disk 0 is close to 3 TB, with a labeled 100 MB partition "EFI System Partition" a 2779,01 GB NTFS partition labeled "OS (C)" and an "HP RECOVERY (D)." 15,28 labeled GB NTFS partition So, there we have the bootloader partition, the partition of operating system Windows 7 and the HP recovery partition.
  
  But there is also a 'disc 1' labeled 'DATADRIVE1 (E)"formatted as one 14.79 GB NTFS partition. I was surprised to see this data disc, because one of my complaints about HP computers in the past (or at least those available through Best Buy) was that they were always set up with one disc for the operating system and data. (It is always a bad idea to host your data on the same drive that your operating system, because the system disks get use more heavy and are more prone to failure.)
  
  I recognized my Western Digital My Book 1 TB drive disc 2, entitled ' My Book (G) ' and formatted as a single partition NTFS of GB 931,48. It is the external drive only, I am informed, plugged into one of the USB 3.0 ports.
  
  So I called the support for questions on disk 1. Where is he? Is what kind of drive? Is what brand? Etc, etc. HP support officer did not know the answer to that! She told me that my system only comes with an internal hard drive and therefore that * must * be an external drive belonging to me. I have an external USB drive connected but it's G drive.
  
  The only USB devices connected physically are: dongle USB wireless keyboard and mouse from HP; My WD My Book drive; and a HP Photosmart C5180 all-in-One printer with nothing plugged into its card reader, who can't stand not anything on the order of 14.79 GB anyway.
  
  I would like to know the details about this DATADRIVE1, because) I don't really know what it is and if I should write data there and b) do not know how stable the device is. Thanks in advance for your help.
  
  ***************************************************
  
  System specs
  ---------------
  
  Computer: HP ENVY Phoenix 810-445qe desktop computer
  Operating system: Windows 7 Professional, 64 - bit
  Processor: Intel i7-4790 CPU with cache, etc.
  RAM: 32 GB (four connectors DIMM DDR3)
  Storage: (see below)
  Video: NVIDIA GtForce GT 640
  Audio: RealTek sound with Beats Audio card
  Network card: 802.11 b/g/n Dual-Band 2 x 2 wireless MIMO with Ethernet, Bluetooth (not out), etc.
  Keyboard & mouse: HP USB wireless keyboard and optical mouse
  
  Storage card
  ----------------
  
  System disk: HDD SATA 3 to with separate cache (Boot, OS, recovery partitions)
  Mystery disc: 14.79 GB NTFS (single partition)
  CD/DVD: Super Multi Blu-Ray/DVD/CD-Writer
  USB ports: 4 USB 3.0 and 4 USB 2.0 ports
  Card reader: 5-in-1 Multimedia Card Reader
  
  What is physically attached
  ------------------------------
  
  Video cable
  Dongle USB for HP Wireless keyboard & mouse
  USB cable for Western Digital 1 TB external hard drive
  USB cable for printer all-in-one HP Photosmart C5180
  Audio output to speakers

  Hello

  Look at least one "storage card" and you will see "separate cache. Which tells me that your PC may have a separate cache device (16 GB).  See the image below.  Check your motherboard for this device in the designated area.  What do you see?

  

• Adding absence of steps to a label

  Hi guys,.

  I feel that this probably isn't a big deal to implement, but I'm still a little new to teststand and hope you can help.  I'm printing a label on the DUT pass include:

  1. number of product

  2 serial number

  3. check the date and time

  To do this, I'll call a labview VI to manage this and passing parameters.  However, now I need to implement a tag that is printed upon failure of the UUT.  The necessary information are the three elements as well as the addition of the name of the faltering steps.

  How can I do to get the faltering steps OM n to switch to a VI print a label?  In addition, the use of a reminder would be logical in a case like this?

  Thanks in advance.

  Hello

  I have attached a sequence that stores the names of the failure of all the steps failed except call sequence.

  Check the file globals. A FailureStr that contains all the stage names.

  I hope this helps.

  Ravi

• Frequently corruption file characterset OCR and real-time CVS1454 exe file

  HI I am facing strenge same problem in the application of vision. I'm using equipment NI CVS 1454. Is there an OCR on CVS application that inspect the product on the conveyor. I made different characters to choose file of different labels on the product. Now main problem is sometimes not exactly when my chracterset file, Pattern matching templete and corrupts my exe in real-time. I joined a few ok and corrupted file characterset here and also an exe in real-time.

  When I open my file (.abc) characterset in Notepad, that I found damaged files after entering text.

  ####
  #Date: Wed, Aug 1, 2008 11:28
  #OSName: PharLap
  #OSVers: 13.0
  #AppName: PH_EXEC
  #Version: 8.5
  #AppKind: AppLib

  LVRT. DLL loads the address: 0x002F6000

  I don't understand how this error massage journal if written in .abc or rtexe files, which make it currupt... I have also attached my structuring code image file.

  Dear prashantpatel21,

  I do not know how to disable the log of LabVIEW RT errors, at least, is not that you or I could have access.

  It's the idea that deactivation of LabVIEW RT logging of errors will decrease even more the impact of corruption?

  Have you made progress with your service request?

  ~ Nate

• Segmentation of OCR and skeleton

  HI, GuysI have annoyance over rock, can someone give me a help or advice? Thank you

  The detail is recognizing the character of a label, after a treatment (see photos), the rate of correct recognition is still not satisfactory. I'm trying to segment them and extract the skeleton of each character. All of the above operations, the result can be better. I knew there is a special function (Segmentation.vi, Skeleton.vi) VI, also tried, in vain. Who can tell me how to use them, or another method.

  Thank you

  Best regards

  --->    ---->

  Gary Guan wrote:

  And could you tell me what is the tool in the image. " is" NI OCR training interface?

  It's Vision Assistant 2009. OCR training Interface is integrated into the Vision Assistant as well.

  Andrey.

• Four cameras to inspect the label presence / Date / batch Code

  Hello

  We intend to use four color cameras (more probably Firewire) to inspect the right label presence (attached image), Date / batch Code (most likely a match and no OCR/OCV), liquid level and presence of Cap. The speed of the conveyor is 240 bottles per minute (ongoing). As the bottles are rotating, there is no fixed orientation of the label. Thus, we intend to capture 4 frames on each trigger, to assemble and to inspect for a suitable Date and batch number, correct label, liquid level and correct the blockage. Good level of liquid is always above the label, so it shouldn't be a problem.

  We need a software / hardware recommendations for the cost of work effectively. For example, can VBAI as well as NI EVS-1464RT work for this application, or do we need to Labview and the Vision Development Module? We have the best price / performance for this application.

  Any comments / suggestion should be highly appreciated.

  Dear Faisal,

  VBAI does not include the steps to assemble the images, I suggest you LabVIEW and the Vision Development Module development.  If you want to use the EVS-1464RT, you will also need a copy of LabVIEW RT.  Note: the Vision Development Module can be purchase as a bundle with LabVIEW RT, see http://sine.ni.com/nips/cds/view/p/lang/en/nid/207699.

  Another way to achieve your goal of a 360 degree view of the bottle would be to use a lens Opto pericentrique Engineering, see http://www.opto-engineering.com/pericentric-lenses.html.  This would allow you to use a camera.

• TouchSmart tx2-1370us Recovery Disc Set failure

  I am writing on behalf of my sister.  Here is his story:

  Screen of her laptop TouchSmart tx2-1370us broke earlier.  It's under warranty where she bought in so he was expelled to be repaired.  When he returned, the screen has been set, but there was a note indicating that they had lost its Windows 7.  The computer loaded and executed perfectly, but it was the pop-up "is not a genuine copy of windows.  She claims that she was unable to read the sticker product key the computer good enough to get it to accept anything, she entered.  When she called the store, they said that HP would be able to help get it back.  HP sold its recovery disks which were to restore the computer.  It is a 3 disc set, marked 2 System Recovery DVD Windows 7 Home Premium and 1 additional CD labeled Application & Driver recovery CD.  CDs ran several times still to come as fruitless after the first 2 CDs.  I won't get in his experience of the customer support, but she claims that she spoke on the phone with HP 6 times in the course of a week and nothing they had to say or to offer.  Always unsuccessful recovery message.  She abandoned, almost crying at this time, and I said I'll try.

  After a bit of searching I found a patch on the HP website that would supposedly solve the problem of recovery disks.  The patch was properly installed, green checkmark and all, and all 3 CDs was successfully.  The computer restarts, the screen of the Installation of the HP software ran for a while before another restart then the usual recovery failure message.  I tried many times with the same result every time.  I saved the newspaper from the last go to it and post it below.  It seems the States BIOS Vista as OS, but she bought the computer pre-loaded with Windows 7.  Could there be something in that fact cause a problem?

  Someone suggested to reset the BIOS to factory default, but that didn't work either.

  When you save the log to USB, I could see all of the files, there are 3 readers listed SDV (C Local disk (D & BOOT (X))

  For any help or suggestion would be appreciated.

  Here is the log:

  --------------------------------------------------
  [2:30:01.41] enter audit OS Edition...
  ----------------------------------------
  [2:30:01.41] check RStone.ini file to determine the required edition.
  [2:30:01.44] out of checking OS Edition...
  --------------------------------------------------

  --------------------------------------------------
  [2:30:01.46] controls if the upgrade to Windows 7 is required.
  ----------------------------------------
  [2:30:01.47] current edition is [HomeBasic]...
  [2:30:01.47] [start] necessary. Don't need to upgrade...
  [2:30:01.47] [Starter] needed...
  [2:30:05.17] necessary [Starter] edition. But is not the case of the [Starter] OS...
  [2:30:05.17] OS edition upgrade might have a problem...

  Management and maintenance of deployment images tool
  Version: 6.1.7600.16385

  Image Version: 6.1.7600.16385

  The current edition is:

  Current edition: HomeBasic
  The operation completed successfully.

  Component: TDC Preinstall diagnosis Tools for Windows 7 - TDC
  Error found: you have set the flag of Vista on an image of Win 7, please use EEPROM to set ~ OS SKU ~ value = 2
  ---------------------------------------------------------------------------------

  [ 2:38:37.07] ------------------------------------------------------------------------------------------
  ...
  Failed to update factory! ***
  [2:38:37.07] Suggest create PIN-journal and send to TWN PDC NB-PreinPM for further analysis...
  ...
  [ 2:38:37.07] ------------------------------------------------------------------------------------------
  [2:29:20.80] Start BBOffline.cmd...
  UPDrv = [C:]
  [2:29:21.35] value UIA 951 error Code
  [2:29:21.68] start [corrections].
  [ 2:29:21.68] ---------------------------------------------------------------------
  [2:29:21.68] FixUps.cmd...
  [2:29:21.68] create overall progress information...
  [2:29:21.72] complete FixUps.cmd...
  [ 2:29:21.72] ---------------------------------------------------------------------
  [2:29:21.72] start [Tweaks for SDRD].
  [ 2:29:21.72] ---------------------------------------------------------------------
  [2:29:21.72] SDRD Tweaks to change the regional settings default user...
  [2:29:21.72] copy C:\System.sav\Util\TDC\MCPP\FBIRES\FBIUSRES. DLL.
  [2:29:21.76] Run "IntlCfg.exe - skudefaults: US-image: C:
  [ 2:29:27.64] ---------------------------------------------------------------------
  Housing starts [2:29:27.64] [Sleep 10 sec].
  Starting price [2:29:37.68] [creation RStoneFUpdate.INI].
  [2:29:47.78] start [create 1 GB Pagefile for offline].
  Volume in drive C has no label.
  Volume serial number is 60E6-4F60

  Directory of C:\system.sav\bbv

  01/01/2001 02:29 1 073 741 824 pagefile.sys
  1 file (s) 1 073 741 824 bytes
  0 26,019,311,616 dir bytes free
  [2:29:47.85] start PININST.exe for offline...
  [2:30:13.27] Start SysID Check...
  [2:30:16.34] Start Option control code...
  [2:30:18.37] Start PIN Tweaks...
  [ 2:30:19.44] ---------------------------------------------------------------------
  [2:30:19.44] PIN Tweaks to hide all for BurnBoot PBO and BBV2 on restored image...
  [2:30:19.44] update PININST_BBV.ini...
  [2:30:19.46] update PININST_BBV2.ini...
  [2:30:19.48] update PININST_BBV2POST. INI...
  [2:30:19.49] update PININST_BBVClean.INI...
  [ 2:30:19.52] ---------------------------------------------------------------------
  [2:30:20.40] starting factory updates...
  [2:30:27.43] installation start QFE offline...
  [2:38:36.81] PININST_OFF: PAST...

  [2:38:36.91] Type C:\System.sav\Logs\BBFindEr.log...

  [2:38:36.93] Type C:\System.sav\Logs\BBFindE0.log...

  -C:\SYSTEM. SAV\LOGS\BBFIND4QFE. JOURNAL
  [2:38:36.93] FUList.log to check if there are double Desc...
  No duplication.
  [2:38:37.05] duplicated No. Desc is located... PAST.
  [2:38:37.05] there was no update from the factory...

  Lets take a chance it's for W7

  Go here and download the correct version of W7 (home or pro, they have not a starter edition), version 32 or 64 bit and the language, it's going to be a file iso very large, once downloaded, burn it to a blank disc DVD + R as an Image, this can be done on a Windows 7 PC, right-click on the iso file and select 'Open with' > 'windows disc image burner.

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/

  This will make a regular windows 7 installation disc allows you to get Windows installed, use the key to see if it will be ignited.

  Then, you will need to download the drivers for your specific model on the HP site and install it.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=4041813&LC=en&cc=us&DLC=en&task=&lang=en&cc=us

• delete a partition on my hard drive that was originally set up by the manufacturer as a backup drive hard to label.

  I hope I am posting this on the forum,

  I want to delete a partition on my hard drive that was originally set up by the manufacturer as a backup drive hard to label.

  I went into computer management console & know that the primary partition - drive C system, boot, pagefile, active lists, dump incident & main partition in brackets but I don't know about the virtual memory paging file. No, there is some data on it. I've been saving the other partition - C drive on an external hard drive.

  I know that I have to back up this data but where I should come back to? And why is it called (Primary Partition) when it is used only as a return to the top by car?

  I'm only wanting to do because I'm running out of space on my drive C & D drive are the same size! 143 GB & 139.5 GB

  I have a laptop of Acer 6930

  Window Vista Home Premium Service pack 2

  Intel Core 2 Duo T6400 2 GHz

  4 GB OF RAM DDR

  64-bit operating system

  HARD DRIVE 320 GB

  I hope I am posting this on the forum,

  I want to delete a partition on my hard drive that was originally set up by the manufacturer as a backup drive hard to label.

  I went into computer management console & know that the primary partition - drive C system, boot, pagefile, active lists, dump incident & main partition in brackets but I don't know about the virtual memory paging file. No, there is some data on it. I've been saving the other partition - C drive on an external hard drive.

  I know that I have to back up this data but where I should come back to? And why is it called (Primary Partition) when it is used only as a return to the top by car?

  I'm only wanting to do because I'm running out of space my drive C & D drive are fighting the same size! 143 GB & 139.5 GB

  I have a laptop of Acer 6930

  Window Vista Home Premium Service pack 2

  Intel Core 2 Duo T6400 2 GHz

  4 GB OF RAM DDR

  64-bit operating system

  HARD DRIVE 320 GB

  Hello

  D: is not a partition backup of your machine.

  Acer has a time set up their machines to the way yours is:

  They had a C: drive for the operating system, a drive D: for data (music, movies, etc you would like to register and a recovery partition 'hidden' to reinstall the operating system and to make the recovery discs to do the same thing.)

  You can merge C: and D: as a whole, BUT save all data on D: first because it will be deleted when you merge.

  "How delete and extend a Partition with Vista disk management"

  http://www.Vistax64.com/tutorials/95418-disk-management-delete-extend.html

  And YES, you back up the data on an external hard drive in case of hard drive failure, the corruption of the system, etc.

  See you soon.

• Pavilion dm4-1160us does not start after the failure of system recovery

  I have Windows 7 Home edition is installed. In my view, it is 64-bit.

  I get everything by initializing the error message is:

  "BOOTMGR is missing".

  Press Ctrl + Alt + Delete to restart»

  When running various tests (Tuneup, break-in, Start-up, hard drive) in I always get the same failure ID: M4PC2J-5KQ6N0-XD6V41-60VG03. The poduct ID is XH124UA #ABA.

  The case began after my computer froze and I forced the reboot.

  I guess that the hard drive is a gonner. Is this correct?

  Hi Mario,.

  Personally, I recommend to replace the hard drive yourself - it is a surprisingly simple process (and much cheaper).  A brief guide on this is detailed below.

  Your computer is listed as coming with a 500 GB hard drive, but you can also easily install a 750 GB HARD drive if you want a little more space - readers at the following links are examples that would be perfect for your laptop.

  Hard drive 500 GB

  750 GB hard drive.

  The procedure to replace the hard drive begins on Page 61 of your & Maintenance Guide.

  Once this is done, simply use your recovery media to reinstall the operating system on the new drive - this is described in the document of HP here.

  If you do not have your recovery media, let me know because there is another option, you can use it as long as you can clearly read the activation of 25-character product key on your label COST.

  Best regards

  DP - K

• p6211f hard drive failure or motherboard chipset - no boot - cant factory reset

  I worked with my friends HP Desktop p6211f for two days now trying to solve the problems start where the main message was reguarding please insert bootable media.  This machine has been maintained by me and bestbuy for virus a few times so it is a prime suspect.  The problem is that the recovery media fails @ 8% with the error 0xe0ef0003

  Hardware HP F9 diagnosis reveals Smart errors ranging from BIOHD-3 and now BIOHD-8 BIOHD-1

  Suspecting a bootloader or simular virus we decided to try the back when we first met the error of 8% indicated above.  I replaced the SATA drive to origional WD 5000AADS (WD Green with AF) with a capacity of 500G also even SATA WD 5000AAKS.  This new disk actually started in windows as it has been previously loaded.  The choice to keep this copy of windows or the rest of the plant, it was decided to factory reset that after the recovery of the disc error was left in a State that doesn't start raining.

  I tried to change the SATA to IDE modes and also tried to change the drive cable with a good known as cable replacement of the drive with my own staff known good disk.  My drive BSOD after logo loading, normal since this window of Windows has been installed on different hardware.

  It has come to my attention of a few Documenhts from HP that the recovery media was probably linked to the new format of addvanced AF with 4 KB vs 512 k sectors, whereas if I replace the drive by another AF I should be good to factory reset?

  My concern is that some messages on the reguarding BIOHD1 through 3 form that replaces the hard drive works sometimes for a few months and then fails, but the real problem is that the faulty motherboard.  I don't want my friend to pay for the drive and it does not work, or it does not, but only for a few months until the bios cannot communicate with him again.

  Test CPU and tests of memory are ok.  DVD rom as well, that there is no other material other then a wifi card and hard drive.

  I can't find the list of motherboards pavilion recalled to check if this Pegation M2N78 - figure.

  Can someone advice me about the best next step.  Can I replace with another drive that is compatible AF or do I have to replace the motherboard.

  Hello:

  I think the motherboard of your model is notorious for failures of controller sata as evidenced in these numerous threads below.

  http://h30434.www3.HP.com/T5/forums/SearchPage/tab/message?filter=labels%2Clocation&location=categor... +

• Disk Boot Failure, Insert system Disk

  Hello

  My HP Pavilion media center m8100n shows "Disk Boot Failure, Insert system Disk"

  I searched on HP support, but I couldn't find a solution from the recovery disk is not available

  Any help would be appreciated

  You are the very welcome.

  Somewhere on the top or side of your PC case, there should be a multicolored Microsoft Certificate label of authenticity (COA) with 25-digit Windows Vista product key.

  It should look like this.

  

  Paul