LabVIEW 2009 32 bit does not not on xp 64-bit

Similar Questions

• A distribution source created in 32-bit LabView 2009, explains that the screws are not executable when opened in LabView 2009 64-bit. How do the main screw?

  A source distribution was made for a VI using LabView 2009 32 bit. The distribution has been verified to work on another machine which ran 32-bit LabView 2009. However, when opened on a 64-bit LabView 2009, the VI was broken as indicated by the error message attached. How can I make the executable VI?

  The VI used the noise and vibrations and HSDL screw that I suspect don't are not supported in 64-bit.

• LabView 2009 (64-bit) IMAQ GetScreenSize?

  Hello

  No one attempted to use of the vi in LabView 2009 64-bit GetScreenSize yet?

  Is not executable more? We have replacements?

  Thank you

  Hello

  IMAQ GetScreenSize is obsolete. Refer to KB: compatibility library when upgrading from old Versions of Module Vision Development.

  Instead of this function, you can use Display.Primary Workspace or Monitors Display.All property node.

  Andrey.

• LabVIEW 7.1 application does not work on Win 7 64 bit

  Hello

  I created an application with LabVIEW 7.1 and related Setup (including the support screws). After installation, the application works on Win XP 32-bit, Win 7 32 bit, but he can't find some analyze VI under Win 7 64 bit.

  Is a LabVIEW 7.1 all application running on Win 7 64 bit, or is it a different problem?

  The messages are that it does not find the screw following "Mean.vi", "ReadFFT.vi". Opens the window of the façade of the demand, but with a broken 'execute' button.

• Mid 2009 Air. Does not start. Grilled motherboard

  Mid 2009, 2.13 with SSD. I started a Youtube video and the screen froze with lines of color stained and with a strong constant cry. Computer was locked up and I had to leave hard. Now, it does not start at the top. The screen stays black when I push the power button, but the computer will beep and the standby light flashes every 5 seconds. I have to hold the power button down a few seconds as a hard to stop it from. Ideas?

  

  https://support.Apple.com/kb/PH21716?viewlocale=en_US & local = en_US

  Please contact Apple.

  Genius Bar reservation

  http://www.Apple.com/retail/Geniusbar/

• In 2012 LabVIEW MathScript RT module does not work

  Hi all

  I recently installed LabVIEW 2012 in my PC with Windows 7. However, Mathscript does not at all. It says "an internal error has occurred in the MathScript RT Module.  Restart LabVIEW and try again.  If the error persists, reinstall the MathScript RT Module. "I did it, but still does not work. It is said further than Mathscript is missing or not installed", but I have installed. What the problem would be, please?

  Have you been able to verify the installation and activation in the License Manager OR? It should say enabled for this computer and have a green square like this:

  

• Ocean Optics LabVIEW 8.2 drivers does not not with USB2000

  Hi all

  I've recently started working with the USB2000 in LabVIEW 8.5.1. I downloaded the drivers from instrument driver page of NOR and tried to install and run.  When I did this, an error message pops up saying that these drivers were designed to LabVIEW 9. If someone has had this problem and nobody knows how to fix?

  Thank you

  Rob

  You have established in your first post that someone does not have the correct project on the web site. Expect NEITHER correct or simply make and post the project in the download thread convert.

• Stand-alone labview application (.exe file) does not run correctly

  Hi all

  I'm doing a labview application only to run on another computer (I never did this before).

  I went through the tools-> build application prompts and was able to build an exe file.

  the program is supposed to control a power meter and measures of power, then save them in a text file.

  When I run the exe, on the same computer, I compiled the exe, the program generates a text file to save data to, but he cannot communicate with the electricity meter.

  There are a few screws Sub and a dll file that are used to communicate with the electricity meter. Would it be possible that I am not say labview to correctly

  include these files when I create an executable?

  What are some common problems that arise when building stand alone applications that could be cause of my problems?

  And no one knows of any good tutorials on building applications stand alone in labview, other than the help files OR?

  Thanks for your help,

  Also, if you used the VISA, include the runtime with your Installer.

• Where LV 2009/2010/2011 does not save the last used folder?

  Hello, where LV2009/LV2010/LV2011 saves the last used folder? I need all three versions on my development machine, and when I open a project, for example, the folder LV2010 is 'data e:\LabVIEW 2010\Projects\Project to\ ". Then I closed LV2010 and open LV2011 and when I click on 'Open' LV2011 starts in the last folder of LV2010 and NOT in my repertoire of standard data 'e:\LabVIEW BitDefender data 2011\' the same LV2011. When I opened a project in 2011, LV2010 will start in the LV2011 project. I think that information is stored within the registry HKEY_CURRENT_USER\Software\Microsoft\Windows\Shell\BagMRU regards Stefan

  I found a solution that works for me (did not find any downside to date)

  Original, I have these files:

  c:\Program Files (x 86) \National Instruments\LabVIEW 2010\LabVIEW.exe

  c:\Program Files (x 86) \National Instruments\LabVIEW 2011\LabVIEW.exe

  and the labview.ini file.

  I renamed the file as:

  c:\Program Files (x 86) \National Instruments\LabVIEW 2010\LabVIEW_2010.exe

  c:\Program Files (x 86) \National Instruments\LabVIEW 2010\LabVIEW_2010.ini

  and

  c:\Program Files (x 86) \National Instruments\LabVIEW 2011\LabVIEW_2011.exe

  c:\Program Files (x 86) \National Instruments\LabVIEW 2011\LabVIEW_2011.ini

  Now the MRU distinguish two different names to EXE and it works perfectly so far...

  If I have problems I will post that here.

• LabVIEW csv file reading does not correctly.

  I try to use the spreadsheet read vi file as follows the attached csv.

  He did some things wrong:

  (1) the first cell in the resulting table has ÿþ attached to the front of it, it looks like labview is striking some special characters, it should not? (Notepad, notepad ++ and excel can open all the file with no problem and no show ÿþ or something like that).

  (2) it is abuse characters from end of LIFE as two line breaks, resulting in empty rows between each row of data. (Looking at the csv file in notepad ++ confirms that the lines are completed with a CR and LF (same as EOL).)

  (3) I read in sub form of string, because one of the columns is nonnumeric, but then I remove this column of and try to convert the remaining string table in a digital picture (failure). It also fails if I shoot an individual element of the array and try to convert it to a number (in either case, using the string fract/exp number), below, I have an example of attempted to read from the 2nd column of the 1st row (index: 0.1) which is being shaped as a string: "1.37238168716431" and conversion which gives 0 as you can see in the snapshot of the façade into a number.

  

  

  
  

• VI LabView 2014 exponential Fit does not return an offset

  Hello world

  I use LabView2014 and that you want to adjust an exponential curve as A * exp (B * x) + C with VI 'exponential Fit'. In all cases, the VI returns C = 0 and attempts to correct this error by using the bad A and B, which of course gives bad results. Any ideas? I have attached my VI.

  Thanks in advance,

  Aaronski

  You must give a better estimate for the parameters of adjustment or to give a tighter tolerance.

  Right now the default on the maximum offset is set to zero, and your tolerance is set to 0.0001. When you arrive at the large exponential, the algorithm stops because it meets the tolerance soon enough.

  EDIT: Try to reduce your ramp so that you use not e ^ 100 in your editing. For numbers that big, even using epsilon machine as tolerance will result in satisfactory adjustment of tolerance with a pretty crude pass. You can also try to reduce the weight of the extremely large numbers of adjustment.

• Remove labview 2009 without using Add/Remove program

  Hi all

  I have problem with the removal of LabVIEW 2009.

  I deleted some folders in the C drive, folder OR.

  Now I can't start my LabVIEW 2009 and it does not appear in my Add/Remove Programs list.

  I tried to delete all the folders and files in the C drive under folder OR, but the pop out error message shows that I don't have the authority to do so.

  So, how can I remove it completely?

  I had intended to reinstall LabVIEW 2009 after that I have completely removed.

  Very much appreciate your help.

  That's why I say try to reinstall LabVIEW. He could just do a repair of your installation. Then, you can use Add/Remove programs to uninstall completely.

  But when you uninstall completely there will be folders OR remaining. These are things like user.lib.

  Have you tried to reinstall the runtime?

  One last thing. I don't know how you got your installation so messed up, but remember that if you build a Setup program you should not install on a system with the development environment. There are so many things that can go wrong.

• iMac does not start after the last security update

  Hello

  After the last update my iMac (late 2009, El Capitan) does not start.

  The iMac starts he accepts my user and password entry, the loading bar stops at 80% and then nothing happens... after I turn off the iMac. Repeating this procedure change nothing.

  Does anyone have any advice for me?

  THX

  INTELLECTUAL PROPERTY

  a solution that helped me:

  Re: security update causes damaged Apps

• Reading TCP does not detect the network closed conncetion error (66)

  Hi dear all,

  Instead of LAN I use WIFI to connect PC and mobile. Read all communications and write operations are performing ok. But the only problem I am facing is that once I disconnect the network from a mobile phone connection my labview TCP read operation does not detect it and only timesout at the specified interval. Although for Bluetooth connection network if I disconnect mobile then BT read detects it as network conncetion closed in error by peer (66).

  Can someone help me on this.

  Thank you & best regards

  Zdzislaw qureshi

  Hi Zdzislaw,

  The behavior you're seeing is expected for TCP as the device will timeout while it is looking for the connection close the connection.  This Wikipedia article explains how TCP protocol works in relation to a handshaking procedure four lanes running in order to close a TCP connection.  I hope this helps!

  Kim

• Table of waveform LabVIEW 2009

  I have a problem with the table of waveform in LabVIEW 2009, the chart will not poster on the table after a few iterations. This is a bug that appeared in LabVIEW 2009. The same program worked well with LV 8.6. Does anyone know a work around for this problem? I am currently using Version 9.0f2

  See the attached diagram

  It's strange...

  I checked that save this return to 8.6 does indeed.

  If you replace the function Merge signals with a bundle of things function seem to work fine.

  There is also something weird happens with the property node. If you start with a pnode for active track, then drag it down to add another element, then change this new element to draw colors, you get an error on the property node.

  

  "Interesting."

  Steve