LaserJet 600 M602 always the default manual feed

Similar Questions

• LaserJet 600 m602: Laserjet 600 too large print the number of copies

  I work at the public library, and we have a Laserjet 600 m602 to our public access computers to use. It is a network printer. We have problem with printer what impression of the office 2010 products, if more than one copy is requested printer will go crazy and print several copies much more than requested. The printer screen will say 1 X print the number of copies. Only way to stop it is to remove as many jobs he sees. It acts as if it were several jobs. We do not see this problem when printing from the Internet. Driver HP laserjet 600 M601, M602 M603 PCL6 HPCM600c. processor is set to WinPrint - Raw. Bidirectional support is disabled.

  Firmware is 2305090_000468

  I had already installed the pilot PCL6 universal and implemented to date to 600 M601, M602 M603 PCL6 thought that could be the problem but it has not fixed the problem.

  I would appreciate any help on this matter before going to is broken on paper.

  Thank you

  Melanie

  Solved.

  After a lot of research on reading and tests finally discovered the problem with drivers print and collate. Default settings for Microsoft Office 2010 and Adobe Reader are to gather if one that one copy is activated. For some reason any that caused printer to go crazy.  I tried the Standard driver and universal for the printer, but always had the problem of printing too many copies. I used the PostScript driver and it solved the problem.  Now just get the number of copies required. Thank you for your help.

  Melanie

• Printing of documents that contain the letter and legal-size pages - Laserjet 600 M602

  We have a printer Laserjet 600 M602, that does not automatically select a tray to print every time someone tries to print a document that contains the letter so many pages of legal size.  The default printer for the Tray 1 (Manual power) and the user will have to walk over to the printer and the printer to select the correct tray.  I went in the printers settings via the web interface and I set the tray settings to the following: Tray 1 - any Type of Size/Any, bin 2 - letter/plain, plateau 3 - legal/Plain and it still does not print correctly.  Unfortunately for the printer settings, it was on that I'm comfortable doing.  I read the print driver may have changed, but we use the driver included with the disc and I guess that it would be sufficient that this driver.  Does anyone know of some setting that I might be able to change the printer or if it is indeed a print driver problem?  Any comments would be appreciated.

  Thank you

  I was able to receive help this morning from HP support.  He turns out, there were two things that I needed to change.  The first is that when printing from a pdf file, there is an option in the print area for "Choose paper according to the size of PDF page source" and the second thing, it was with the printer printing preferences.  In the printing preferences, under the "Printing shortcuts" tab, the paper Type has been set to Prepunched.  We changed this Unspecified.  After making these two changes, the user is able to print correctly in the printer.

• HP laserjet 600 M602 tray 2 doesn't recognize a paper A4.

  Stage two does not recognize A4 paper. I tried to adjust the tray itself and it is defined correctly for A4 format. I tried to adjust the status bar for different size documents, but there is no change.

  The tray by default one size of paper custom 170 X 282 mm, which is the most important, that it will allow me to set the custom size. Other sizes it recognizes ate A5 A6 B6 and postcard but not A4.

  Tray 1, the manual feed tray prints ok but I need bac to be the default bin.

  Does anyone have a solution to this problem?

  Thank you

  Hi swatson888,

  It is a product of the profit margin. For the best answer to your questions, you need to transfer your question at the following links.

  http://h30499.www3.HP.com/T5/business-support-forums/CT-p/business-support

  http://h30499.www3.HP.com/T5/printers-LaserJet/BD-p/BSC-413

• LaserJet 3015: twisted in LJ 3015 manual feed envelopes

  I'm having a problem with one of the LaserJet 3015 HP that I have the service, the client will print envelopes from the manual feed tray 1, but the machine pulls the tortuous envelopes. I checked the roll and cleaned and checked also the separation pad, which looked good. Clean around the section meeting registration and transfer, without change. 59 k printed on the machine, with 10 k of hand feeding.

  Should I replace the drive roller and separation pad, even if it seems that they have no wear?

  The most common reason for envelopes printing crooked is the Guide plate resting on the walls of the media are not tight enough.  If you have just a bit of game media may go the tortuous.  Press guides firmly against the envelopes and it must feed in a straight line without problem.  Also check the support itself.  If the edge is not flat (from the air inside) it can have an effect on the movememt.

• LaserJet Pro CM1415fnw: Change the default setting for the file tif to pdf on LaserJet Pro CM1415fnw

  How can I change the default setting from tif to PDF when scanning?  I can't find the "Advanced settings".

  Hi @kkeach,

  Welcome to the Forums of HP Support! I see that you want to change the setting in PDF format when scanning documents. I want to help you solve this problem. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Did you download and install the drivers and software HP LaserJet Pro CM1415 multifunction printer full color or a Windows Update used to install the drivers?

  You use the HP scanning software?

  I submitted this document to change scanning settings using the HP scanning software.

  Multifunctional HP LaserJet printers - how to scan (Windows 8).

  Here is a screenshot of the HP Scan software and what options should be available:

  

  If there is anything else I can help you, let me know. Thank you.

• HP LaserJet M1536dnf copy of the automatic document feeder

  HP LaserJet M1536dnf MFP

  FW version: 20130114

  I load the paper in tray and press copy ADF on the front panel button.

  Once this UPM retrieves the document, it crosses all the way to scan and UPM returns to ready state without printing anything.

  Copy in the same way to scan flat ends with a scanned copy of printing as usual.

  I suspect that the problem of Firmware.

  Any help?

  Hi, Jason
  I think you forgot to mention what buttons I have to hold in the power of the UFM.
  I did re-init procedure (hold right + Cancel when power on) and reflashed latest firmware. It did not help.

  If I do a search with the ADF, the printer tries to print anything. UPM simply returns to the ready state after the end of the analysis.

  Update:

  It seems that I fixed it.

  I did the procedure exactly as Jason suggested, but when I checked whether the problem is resolved, UPM did the same, scanned and returned to the ready state without printing anything.

  After that I did hard reset again, then immediately I did again the procedure to reset internal memory

  Spoiler (Highlight to read)

  (Turn off the UPM, press front panel and hold right + Cancel buttons, power on UPM during their detention, let them go after the LCD displays "init memory" and wait as UPM to ready state.)

• LaserJet 600 M602: HP LaserJet 600 M602 don't will switch to tray 2 when Tray 1 is empty

  Trouble for the printer to automatically go to tray 2 when Tray 1 is made of paper.

  A number of things that happened here.

  1. the printer I have access to proved to be wrong. It was actually a M402. Then when I would try to fix the settings via remote access, he would change and then do nothing (because wrong settings of the printer).

  2. the sliders in the trays that are supposed to be flush on paper, were in fact not flush with the paper.

  This resulted in a loud knocking coming from the printer and the printer does not pick up paper from the bin.

  Thank you very much for the help!

• HP LaserJet 600 M602: HP LaserJet 600 M602

  Printer is stuck on 4/8 initialzing mode, I have tried unpluging it to taken for 60 s, also remove the cartridge and can not go past this message 4/8.

  Help, please!

  Try a firmware update using the method of pre-launch usb.  You will need to download the firmware from hp.com.  Then, you copy the bdl of firmware on the USB and use the usb in the front entrance which is covered with a small square piece on the front of the right side.  He jost comes out.  Follow the instructions in the link below:

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c03176293#N10407

  You can download the firmware from the link below.  You will need to run the zip file, and then copy the bdl folder zipped to the usb thumdrive.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5254097&swItemId=lj_99516_13&swEnvOid=4062

• HP Laserjet 600 M602 printing reverse

  the pages are coming out opposite. for example, when printing the letters are white and the rest of the page is black. What can I try to fix this

  michaeljosh87,

  I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a printer. You can do so at http://h30499.www3.hp.com/hpeb/ .

  I hope this helps.

• HP LaserJet Enterprise 600 m602 slow printing during the passage of the trays

  Hello world!

  On the HP LaserJet Enterprise 600 m602, who met breaks in print jobs during the passage of the trays?  Example, we are going to print invoices and we have a rule configuration that prints on plate 2 with the exception of the last page that is perforated paper tray 3.  So, in a job of 5 pages, pages 1-4 are the tray 2 paper... then page 5 is perforated tray 3.  There is a 2 to 3 seconds when the last page is extracted from tray 3.  If the invoice is only 2 pages, the print job appears super slow.

  This printer was working fine with no delay until we applied the firmware 2302786_433718.  Now, the delay is very noticeable.  We do not know if it was intentional or not in the new firmware.

  We use the latest PCL 5 Universal Print Driver.  The only thing that has changed is the firmware.  We even tried a full reset of firmware.  Problem is still there.

  I worked with HP support, but we were told to wait... the next version of firmware that may or may not fix everything.

  Any help or insight is appreciated.

  We have this same problem with our printer HP Laserjet 600 M602.

  Could solve by setting the Print Mode to all papertypes that are used for the same parameter.  We thought initially can be a problem, issue or firmware of the Board of adjustment, but in reality was the paper type settings. We set up printer for ordinary paper into tray 2 and tray 3, default regular bond has been set at light mode printing and binding for the print mode binding. Each time dial-up printer and trays, he stops to configure different paper type settings.

  Hopefully the other help solve their printing problems

  Enjoy your day,

• The model HP LaserJet 2430 Q5964A only print from the manual feeder

  The LaserJet printer will no print (Tray 1) manual feeding.  We need the printer to print only starting from tray 2.  I tried to change the settings to the local node as a server-side.  I tried to make the Tray 1 not available both client-side and server without result.  Regardless of what I select settings, the printer will always say, ' manually feeding heavy extra paper.  I do not use a card stock.  I use a brand line 2 MACO of 10 very similar to Avery label sheets.  How can I get the printer to pass the Tray 1 and only draw starting from tray 2.

  Please, do not provide generic answers to change the size and type of paper.  I did this several times.

  Currently, tray 1 is A4 size, and the Type of tray 1 is labels.  I also settheis to envelope #10.  No matter what is put here the printer insists on the use of Tray1.

  Tray 2 has currently the size value LETTER.  Default paper size is set to letter.

  

  Without the help of HP, on mine I found a solution.

  1 remove the printer from the server

  2. go to the computer of each user who uses the said printer and remove it form the devices and printers

  3. return to the server and add a printer again (used PCL 6) since August 2013 instead of new

  4. replace in the computers of users and add the printer again.

  5 test printing.  It worked correctly in my situation.

• 2.6.5 lightning Thunderbird 24.5.0, add-on. Default calendar, 60 min. length 'event '. Cannot increase the duration manually in the box dialog "Edit event" or "options".

  My computer is an ACER Aspire with Windows 7, 64-bit, processor i3 - 370 M. I used Thunderbird and the add-on Lightning for years and love it! The above problem (event time cannot be set either shorter or longer than the 60 minutes.) has started happening recently (I guess after a recent automatic update of one or two programs).
  To solve the problem, I tried:
  1. to change the time of 'end' in the dialog "edit event". When I changed the "end time" 09:00 the "beginning" at 12:00, climbed from 08:00 to 11:00, that is to say. keeping the default of 60 minutes.

  2. I then tried to change the duration of the default event of 60 minutes to 240 minutes in 'Options '. the dialog box has accepted the change, I saved; restarted; options checked to make sure that he had maintained change duration (he had), but the "edit event" dialog box always always at 60 minutes and could not manually increased or decreased.

  Can you help me?

  At the right end of the field time is a small icon. When the tips of the two links are in contact with the time of the event is locked to the default duration. Click on this icon and will separate the ends of the links and then you can change the duration.

• Is it possible to change the default print on a HP LaserJet 500 printer M551 color tray

  Hello

  Is it possible to install the default print to the HP LaserJet 500 color printer tray M551 be impression tray 2 times online and live?

  If so, what would be the best way to go to implement?

  Thank you

  Hi thanks for taking the time to answer.

  In the end, I gave a call to HP support, and they explained to me that the default tray will always be Tray 1 if it is open, and if you add additional bins, one at the bottom will become the default tray.

• HP 7510 - Always scan the default loading paper

  A few months ago the default parser using the paper feeder instead of scan during the scanning bed.

  Even if I close the tray of paper, he will roll/try feeding of the paper in the tray instead of scanning from the bed.

  I have reset settings one or two times, but he always return to the default values.

  Is there a setting somewhere that I can put it to bed scan?

  Hello

  Just test mine (also a 7510). You hear a 'ting' noise when putting paper in the ADF? I think that it has a sensor and you may need to clean the surface of the sensor. How to clean I don't know, the printer is a printer ready so I don't want to break it.

  Kind regards.