Latitude E6530 - ongoing fan on food

Similar Questions

• Latitude E6530 with Intel HD 4000 + E-Port Plus APR + external monitor 4K

  I have a Latitude E6530 config:

  • Intel Core i5
  • Graphics Intel HD 4000 (+ the latest graphics drivers for Dell 10.18.10.4425)
  • E-Port more APR (2 DisplayPorts)

  I would buy a 4K display to use with this config. I'll be able to use it on 4K resolution?

  I use a dual display configuration. 1st is my laptop built in FullHD screen, and the 2nd would be the 4K monitor.

  UPDATE:

  I went to a nearby store with my laptop + APR to try a 4 K monitor. :

  • A monitor of Samsung LU32E85KRS with 4K capability works only in the resolution of 2560 * 1440 (60 Hz) attached to the port to display the Apr.
  • A wide S34E790C of SAMSUNG monitor (Native res: 3440 x 1440) work as resolution max. (60 Hz) attached to the port to display the Apr.

  That means, my laptop hardware (or software) does not support a resolution of 3840 * 2160 4K full. :(

  UPDATE 2:

  I have successfully created another 4K (LG 27UD88) monitor with my laptop with full 4K resolution (3840 * 2160) 29 Hz via Displayport. It works like a charm.  :)

• Windows Update runs continuously after the installation/purchase program for Dell Latitude E6530 with Windows 7 Pro 64-bit

  Hello

  I bought a Dell Latitude E6530 'renovated', that was the end of the lease. (It was not defective). I started up and installed Dell help. I have had no trouble to do a few minor update of drivers. However, when I try to update Windows it just runs and.

  I checked the Windows Update with the troubleshooting Diagnostic Utility. I made sure that there is no infection or rootkits on your computer. I followed several suggestions I found the title of Microsoft Support positions and renamed the folder of Distribution system, as well as a few things of the reset. I have register/authenticate online with Microsoft Windows software.

  When I run the troubleshooter, it says registration for the Service is missing or damaged, and he said it suits him, but he can't solve "problems installation of recent updates. However, when I run it again, it is said that he correct once again.

  Any suggestions?

  Melissa

  Check this thread - it helped a lot of us:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-update/Windows-7-update-solution/f39a65fa-9d10-42E7-9bc0-7f5096b36d0c

  Kimmo

• Problems of latitude E6530 USB 3.0 Windows 8

  Hello

  The left USB 3.0 on my Latitude E6530 does not work when I connect a USB 3.0 device to it. If I plug in a USB 3.0 in device after Windows starts, it does not recognize anything connected to this port. If I connect a USB 3.0 device to the front port to turn the system, Windows will recognize the device once it starts (it will mount an external hard drive, for example), but will immediately report there is error when loading it. This port usually does not recognize devices USB 2.0 without any problems.

  USB ports are working fine. I can connect USB 3.0 devices in the USB 3.0 port right, and they work. I can plug in devices USB 3.0 to one of the USB 2.0 ports, and they function as devices USB 2.0, as expected.

  I am running Windows 8 Pro.

  It's probably a driver issue or a hardware issue?

  Thank you.

  I have the e6530 of Latitude with the docking station and NONE of my USB 3.0 ports act as 3.0.

  But I'm happy to say that it is corrected now! :)

  I had later "Intel USB 3.0 eXtensible Host Controller Driver" is downloaded from the Dell site and Device Manager reports no problem - but every time I have pluged a USB 3.0 device in any of my "SS" USB 3.0 ports I am greeted with the message "this device could accomplish a lot faster..." "in my systray.  :(

  I downloaded USBTreeView (freeware) and when I connect a device, according to me, it connects to a USB 2.0 hub port.  No 3.0 ports under my "Intel USB 3.0 eXtensible Host Controller Driver" were already used.  :(

  But this thread solved my problem. The problem is the last "Intel USB 3.0 eXtensible Host Controller Driver" driver on the Dell site is almost a year older than the latest in Intel.  Thank you JeanPier - your message has reported me here:
  en.Community.Dell.com/.../20503380

  .. which brings me here: https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=21129

  Download the latest version of the host controller, Intel, install it (unzip & run setup.exe), reboot and your problems will be solved...!

  See you soon!

• Latitude E6530 will not wake up

  Hello

  I had an E6530 of Latitude with an E-Port II a few weeks ago. In general, it's great, but I got an annoying problem a few times:

  The laptop is connected with the lid closed and two external monitors and external USB keyboard and mouse connected. It is currently running Windows 7 Ultimate.

  The laptop goes to sleep after a few minutes of inactivity.

  When I press the power button on the dock to get out of sleep mode, standby mode external monitors stay and the mouse and the keyboard doesn't work (no light caps lock num or laser on the bottom of the mouse).

  If I disconnect the laptop and open it, the screen stays off and it does not meet the keyboard or touchpad, even after several minutes of entry. However, the power light is on and the hard drive flashes sometimes. The only solution is to turn off the laptop by holding the button for a few seconds.

  Note that this happens whenever the laptop is awake from sleep, happened only 3 - 4 times per month. The Windows logs don't show any errors either.

  Does anyone else have this problem? If so, how to solve it?

  Thank you

  Alistair

  This blog gives to think that it could be caused by the O2Micro driver for the card reader integrated:

  gnawgnu.blogspot.nl/.../Fix-for-Wake-After-Sleep-Freeze-on-Dell.html

• STOP: 0X0000007E (0XC0000005, 0XF17FC30B, 0XF8AB7ADC, 0XF8AB77D8)

  Computer was working fine, then the screen became all monochrome (but not blue, off-white).
  This occurred during a comprehensive analysis of Microsoft anti-virus program «Securities Essentials»
  The computer is itself kept running as I could hear the ongoing fans and LEDs are stayed on.
  Unable to see anything or if she was responding to keyboard or mouse movement entries I turned it off.
  When the computer reboots, initially it seems to be OK, going through the process of the usual display of Windows XP on startup. He was even on the screen where it shows the different user accounts. But then 2 seconds later got the following error message:

  ----------------------------------------------------------------------------------

  A problem has been detected and Windows has shut down to prevent damage to your computer.

  If this the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow

  the following steps:

  Make sure you have enough disk space. If a driver is identified in the stop message, disable the driver or

  Check with the manufacturer for driver updates. Try changing video cards.

  Check with your hardware vendor for updates to the BIOS. Disable the BIOS such as caching memory options or

  the occultation. If you need to use Safe Mode to remove or disable components, you restart the computer, press F8 to

  Select the advanced startup options, and then select Safe Mode.

  Technical information:

  STOP: 0X0000007E (0XC0000005, 0XF17FC30B, 0XF8AB7ADC, 0XF8AB77D8)

  SiS163u.sys - address F17FC30B base at F17F8000, DateStamp 41ab05b9

  Beginning physical memory dump
  Total physical memory dump.
  For more assistance, contact your system administrator or technical support group.

  ----------------------------------------------------------------------------------

  Probably from about 5-7 years old eMachine race T1150 pre-installed Windows XP Home Edition.
  1.30 GHzz/celeron to Intel processor.
  What follows is also on the case - "3D Intel Direct AGP Graphics", I think it's the chipset.

  No new material has been added or deleted in over a year.
  Recently the Microsoft "onecare.live.com" scan and difficulty.
  After that, I installed the Microsoft «Securities Essentials» Supposedly without concern for quality, virus protection for your PC at home of Microsoft.
  It seemed to install OK and I could do a quick scan & difficulty.
  The problem occurred in the middle of the analysis I did later.
  Turned off and on again and received the same error message.
  Shot and a third time and got into safe mode.
  I tried "using last good known configuration", but I got same result.

  Also during the installation of Microsoft "Securities Essentials" uninstalled various antivirus programs (program at the request of the main titles") that were on the computer. One of them could have been something called EMCO Malware destroyer.

  Known solutions or ideas?

  FYI - the system and software came pre-installed & I don't think they gave me a CD with XP on it, so a solution that doesn't require you to put the CD in the dvd player is going to be my only option.

  You go to the website of the mftr. (Trendnet here) and download the drivers. It's the only place wherever you get them unless you have recorded the CD originally supplied with the unit. Usually, you can reinstall the drivers, but if there is an entry in Add/Remove programs and uninstall the device first.

  Incidentally, be proactive in preparing for the inevitable:

  http://www.elephantboycomputers.com/page2.html#Backing_Up

  I say this not to offend you in any way or to suggest that you 're not saving, but if you don't are not then you should be aware that your computer has gone its normal end of life, so be prepared to die. Certainly, he could go for years but OTOH it would not be surprising if he does not. MS - MVP - Elephant Boy computers - don't panic!

• Cannot connect wirelessy

  Try as I might I cannot print from my laptop on my HP PSC 1410 all in one printer without a USB connection. I am trying to connect wireless.

  History:

  I ran this facility for years when I was running Windows SP.

  I've updated my Pc and laptop for windows 7. The PC is 32-bit and the laptop is 64-bit.

  The router and the printer are connected to the computer. I have no problem printing from the pc with the USB cable is connected. I can also print from the laptop via a USB cable. What I can't do is the laptop wireless printing.

  I tried to update the software and drivers. I ran each HP diagnostic tool. The laptop is connected to the wireless internet and works perfectly, but will not be printed without cable.

  Micron PC, Dell latitude E6530, router Netgear WNR 1000, internet connection high speed.

  Can anyone help?

  Hi choices,

  Thanks for the info, but my son and I come to spend too many hours trying to make it work wireless so I came out today and bought a HP OfficeJet 8600. He set up wireless on both computers without cables. I'll put up my wife's cell phone now and then my phone. Thanks for the help

  CAL - c

• Computer suddenly stopped

  My computer suddenly shuts completely anywhere from half an hour to several hours apart. I get a box that says location information, but it closes so fast that I was never able to read. I noticed that I had to completely connect. Can anyone help

  Hello

  A spontaneous stop that does not have Windows stop properly is usually initiated by the hardware of the system to prevent damage to the components. Usually, as 99% of the time, it is due to an overheating condition. Modern hardware system monitors this condition and automatically shut down the system if the temperature exceeds pre-set limits. Turning off this feature or change temperature settings is not the right solution, even those these options may exist in the system BIOS.

  The right way to cope is to open the case and blow out any accumulation of dust or debris, in particular on the processor fan and heat sink. You want to check that all fans, including food, work correctly and replace any that are not. Make sure that the tower itself is placed in a position where there are a lot of circulation of air, do not place it in a cabinet with a door that is closed all the time, simply won't be enough air flow.

  In the case of a laptop, the best you can do is ensure that the intake and exhaust exits are cleared when the system is in use, and sometimes, it is recommended that you use a cooler rug to make life easier along. Using one on a soft surface like a pillow or cushion bed can make the problem worse by blocking air flow and prevent the circulation required to dissipate heat build up.

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• (Redirected) HDMI cable on laptop support

  Hello world

  I would like to know the length of the HDMI cable that can support on Dell Latitude E6530 laptop.

  Tested with 10 meters - worked well with the two E6530 & E6520

  15 & 20 meters cable has worked with E6520 but failed with E6530, not yet worked with PIX of 1280 * 1024.

  Hi bschouhan,

  Please repost this in the laptop computer forum help.

  http://en.community.Dell.com/support-forums/laptop/f/3518

• Reference Dell backup and restore (Premium Edition) 1.7.5.63

  Since upgrading my software Dell backup and restore to version 1.7.5.63, I now have problems to make it past the "Dell backup and recovery Please Wait" screen.

  I'm not leaving this option to run for more than 8 hours, but found that this process is not always successful. The only way I could find to block this process to run is to click on the? at the top right of the screen, then select "activity log". At this time, I clicked on the home button to take back me to the Dell Backup and Recovery Premium Edition home page and close the application. However, when I tried to re - open the application again, it brings back me to the screen "Dell backup and recovery Please Wait".

  To solve this problem, I tried to restore from a previous backup I made of the Dell Backup and Recovery application but it failed miserably and corrupted my hard drive and operating system (Windows 8.1). So the only way I could get back to who had to go back to my backup bootable disks that I created when I arrived to my laptop Dell Latitude E6530.

  Then I had re-installed all the 100 + updates of Windows for upgrade to Windows Pro 8.1 by the Windows store. From there, I upgraded my software "Dell backup and restore (Premium Edition)" at 1.7.5.63 and had the same problem again.

  In any case to have a fix for this or tell me how I can raise an incident with Dell, because this is so ignorant and frustrating.

  If I uninstall my Dell Backup and recovery software (Premium Edition) and reinstall the version found in http://www.dellbackupandrecovery.com/en-us/Index.html , but the last time I did, it installed the basic edition and not the Premium edition.

  All right enough the last time I had problems with my Dell backup and recovery (Premium Edition) software, it seems to settle on the other updated after a few months, but I don't don't want really to go back to an earlier backup with an older version of the recovery (Premium Edition) software and backup Dell.

  Any help or advice, you would be extremely grateful.

  I'm shocked that Dell is detrimental to Windows backup in Windows 7 Professional.  Your comments here persuade me not to pay for the premium edition.  Various people on other internet research said Dell had a great program backup, 6 months ago, but weakened while it is able to sell a version Premium, also hobble the program backup Windows.  You might try a free backup software like Comodo as I suspect that you can not use the Windows backup which makes a backup with files image.  It was a very simple approach that Dell seems to have stuck in their new versions of Windows 7 Professional.  I restarted my computer because of this kind of game.  Since I bought it at Costco, I have 90 days to return it.  I also started watching a series of online backups.  Carbonite seems terribly clutter my computer, and while highly recommended, it is slow, slow, slow.  I am CrashPlan that seems to work much much much faster.  Both of these are paid services.  CrashPlan has a lot of versatility to accommodate beginners to evolve into something much more powerful.  They have free versions for recording to hard drives and other computers.  The online version has Unlimited storage, much versatility, without the limits other plans have, and it's only 4-6 dollars per month, depending on the current sales and payment terms.

• Need help with the SSD upgrade

  Dear Sir
  Sorry for my bad English. I use Dell Latitude E6530, I want to move to the SSD. But my concert is: How can I copy / clone the original to new SSD HHD RECOVERY PARTITION so that I can use it as a 'factory reset' on the new SSD?

  Thank you very much!

  

  The trip key is F12, F8 not, but yes - once you have the recovery media, you can restore the system to the condition of the plant if necessary.

• Question about LINKS 386 PRO MS-DOS Version?

  In 1995, I bought the Version of MS-DOS PRO LINKS 386, produced by ACCESS SOFTWARE INC. It is a GOLF software designed to be played on a computer. My question is if I can install this program on my computer Dell Latitude E6530 laptop with Windows 7 OS? I have a lot of memory and hard drive capacity. I have the MS - DOS diskette 4 of each program. I have an attachment to disk installer for my laptop. If you think I can get a compatibility please suggest a procedure for installation. I'm a bug of golf and these cold long winter days have led me to take this program from my archives to play.

  Main

  There is no easy way to do especially if your Dell is 64-bit.  You could try an XP virtual machine in win 7 and it works on the XP VM.  You could try to find an emulator like DOSBOX (http://www.dosbox.com/)

  It will take some fiddling.

• Uninstalling SQL Server Compact 3.5 for devices error 1325.Documents is not a valid short file name.

  I tried to uninstall all parts of SQL Server Compact Edition 3.5 v (there were 3 parts); the third part, which is

  Microsoft SQL Server Compact 3.5 for Devices - ENU

  will not uninstall and I get an error message, which has in its title "Microsoft SQL Server Compact 3.5 for Devices", (which seems to me indicate that he might be from the application itself?)

  READING: "error 1325.Documents is not a valid short file name."

  Is there a valid way to uninstall this, given the problem - or an another workaround?

  I hope that it is not bad form to reply to my post (!), but I am pleased to announce that this Microsoft utility fixed my problem. I ran it, it looked for my system, then asked me if I wanted to uninstall or install a program, I chose to uninstall, it sought then yet once showed me a list of installed programs. I have selected SQL Server Compact 3.5 for Devices in the list. They asked me if I want to uninstall it (I think that - already done and I do not remember)-anyway, I welcomed the utility for uninstall and there was no problem. It is very useful. I don't know if the source of the error and this solution is specific to windows 7 64 bit, which is what my DELL Latitude E6530 is running, or if it is a general problem and fix. I'll never know the root cause, but at least I can go forward.

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall

• Ports USB U2312HM works not when connected to USB 3

  I use a U2312HM to work, but when I plug the USB connector to a USB 3 port on my laptop, the USB 2 ports on the monitor are not recognized. Device Manager shows it as an unknown device and no drivers to install can be found. When I use a tool like slim or driveridentifier drivers it doesn't ID the device but shows not all compatible drivers.
  When I connect the monitor to the only USB 2 port, I have on my laptop that hub is USB monitor comes to life, but I'm already using this USB port for another purpose. Can anyone tell my where I can find the correct drivers?
  I'm running Windows 7 Pro SP1 on a Dell Latitude E6530, processor Intel Core i7 3770QM with 8GM ram.

  Kvwielink,

  Install this driver, restart when done, repeat the test.

  Intel USB 3.0 eXtensible Host Controller Driver
  https://Downloadcenter.Intel.com/Detail_Desc.aspx?DwnldID=21129

• Question of presentation on EDGE 95 MXP

  I have a client who has an EDGE 95 MXP system and complains that he is to have a lot of problems with its laptops, make presentations of PC. Some of its laptops work well, others not. He reported the following portable computers as does NOT:

  HP 8740w

  HP 2560p

  HP 2550

  HP 8560p

  Dell Precision M6700

  HP 6730 b

  He had no problem with the following laptops:

  Dell Latitude E6530

  Dell Latitude D630

  What's weird, is that if he uses a 50 foot DVI to VGA cable for its computers laptop problem, it works! It does work with the original cable 15 feet. The cable has been replaced so we know this isn't a cable problem. The codec was also replaced at some point. 50 foot DVI to VGA cable was a Cisco came up with solution but the client indicates that it would be foolish...

  Anyone got any ideas how I could get this client on my back? I am sure that it is a setting of the laptop or the driver to the origin of the problem, but my client just it.

  Thanks for all your help :-)

  We have seen similar problems in the past with some portable computers when using DVI VGA, replaced cables cables with VGA to VGA cables and used a VGA to DVI adapter on the codec itself set. (We also forced 'VGA Out quality XGA')

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.