LCR PXI-4072 floating or not floating device

Similar Questions

• Controll PXI-4072 via VISA

  Hello

  I try to communicate with the PXI-4072 using VISA drivers. I m using Fluke MetCal / MetTrack to calibrate the 4072 and want to

  do this automatically, without use of th niDMM FrontPanel.

  But MetTrack Fluke will scan only the RS232, LAN, GPIB and USB Bus for a device, not the PXI chassis.

  Anyone know a solution to calibrate or adjust the PXI - 4072 FlexDMM (or any device PXI)?

  Thank you

  Robert

  You must use the API OR-DMM to calibrate the 4072. The generic driver of VISA will not cut, because you will not be able to log of calibration, take action, make adjustments, or really do much else than reading/writing specific registers, which is not supported or recommended. In addition, you cannot use the Soft Front Panel for calibration, as this must be done in a very specific order at a meeting of calibration.

  I do not personally know with MetCal/MetTrack, but it seems that Fluke has provided certain procedures for the PXI-4065 and USB-4065. Since they don't seem to have a procedure published for the PXI-4072, if you want to use MetCal, you will need to code your own version of NOR published the calibration process, which is installed with NOR-DMM and is also available via this link (I searched ni.com for "4072 calibration").

  In general, for any device PXI, you don't want to use VISA to communicate, but rather use the appropriate API, calling in DLLs of the API (nidmm_32.dll or nidmm_64.dll in the case of NOR-DMM).

  Your other alternative is to use NI Calibration Executive, who has the procedure of calibration for all the NOR-DMM ready to go.

  Please let us know if we can be of further assistance.

  Tobias

  Software engineer

  Modular instruments

  National Instruments

• What happens if the PC I just downloaded Itunes on & connected to, does it display not all devices?

  What happens if the PC I just downloaded Itunes on & connected to, does it display not all devices?

  Hello 2sealadies!

  Thank you for joining the communities Support from Apple! Looks like you have a problem with your iTuens on Windows 10 not to recognize your iPhone. I know how important it is that the iPhone is recognized by iTunes. Read this article with steps If iTunes does not your iPad, iPhone or iPod. Specifically, after the first series of measures:

  If you are using a Windows PC

  1. Open Device Manager by following the steps for the version of Windows that you have:
     • Windows 10: Click the search box in the lower left corner, type Device Manager and press ENTER. In the list under Bus USB controllers, find the Apple Mobile Device USB Driver.
     • Windows 8: loose in the right edge of the screen. Press search and enter the Manager devices, and then click Device Manager. If requested, enter your password. In the list under Bus USB controllers, find the Apple Mobile Device USB Driver.
     • Windows 7: click on > Control Panel > system and Maintenance > Device Manager. If requested, enter your password. In the list under Bus USB controllers, find the Apple Mobile Device USB Driver.
  2. Even if you do not find the Apple driver, follow the steps below, based on what you see or don't see.

  The pilot and
  No symbols

  A down arrow
  by the driver

  Exclamation or
  question mark by
  the pilot

  No Apple Mobile
  USB device driver

  You don't see symbols next to the Apple Mobile Device USB Driver

  If you do not see , , or of the Apple Mobile Device USB Driver, look for third-party software conflicts. Then if you still need help, restart your Apple Mobile Device Service or contact Apple technical support.

  

  You see an arrow down

  If you see next to the Apple Mobile Device USB Driver, the driver with the right mouse button and choose enable from the context menu. Then if you still need help, contact contact Apple technical support.

  

  You see an exclamation point or question mark

  If you see or the Apple Mobile Device USB Driver, right click on the entry, then manually update the Apple Mobile Device USB driver.

  

  You do not see the Apple Mobile Device USB Driver

  1. Disconnect your device from your computer.
  2. Save a screenshot by pressing the Home button and sleep/wake button of the device button at the same time. The screen should Flash briefly.
  3. Reconnect your device to your computer.
  4. If you see one of these sections in the Device Manager, expand them:
     • Imaging devices
     • Other devices
     • Portable devices
     • USB Bus controllers

  Now, locate the entry that recognizes the device as a camera. You should see 'Apple IPhone', 'Apple iPad' or 'Apple iPod '. Right-click the device entry, and then manually update the Apple Mobile Device USB driver.

  If a single unknown device appears, follow these steps:

  1. Right click on the unknown device entry.
  2. Choose Properties from the context menu, and then click the Details tab.
  3. In the drop-down menu, select hardware IDS.
  4. If the ID begins with something other than USB\VID_0000 & PID_0000, go into the Device Manager and right click on the entry for device unknown, and then manually update the Apple Mobile Device USB driver.
  5. If the ID begins with USB\VID_0000 & PID_0000, then follow the remaining steps.
  6. Unplug the unit and remove all the USB devices on the computer.
  7. Shut down the computer, and then turn it back on.
  8. Reconnect the device, tests of each USB port for about 30 seconds to see if the device is recognized.
  9. Test with a different, checked 30-pins-USB or the lightning-connector-cable-USB, if they are available.

  If you still need help, contact Apple technical support.

  

  Manually update the Apple Mobile Device USB driver

  If one of the sections above directs you to this section, you should already have right click on an entry in the Device Manager. Now, follow these steps:

  1. Choose update driver software.
  2. Choose "Browse my computer for driver software."
  3. Choose "Let Me pick from a list of drivers for devices on my computer.
  
  
• Click the disk button. If this is not available, choose a category of devices such as Mobile phone or storage device, if in the list.
• Click Next. You should see the disk button.
• Click Browse and navigate to C:\Program Files\Common Apple Mobile Device Support\Drivers.
• Double-click the file "usbaapl. If you have a 64-bit version of Windows, this file will be called "usbaapl64". If you do not see here "usbaapl64" is not a Drivers folder, look in C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers.
• In the disc window, click Open, and then click Next and then click Finish.
• Windows installs the driver. If a message indicates that the software that you install "not passed the Windows Logo test", click on continue. You can get help with other common errors and the error code numbers in this Microsoft article.
• Open iTunes to make sure that iTunes recognizes your device. If not, Restart the Apple Mobile Device Service.

See you soon!

• Portege R830 - external HARD disk error - "target not found device.

  Hi all

  I recently bought a 1HD R830 which has windows 7 as its OS.
  I have a few old external hard disks that were formatted on windows vista.

  When I try to use it on my new computer it says "target not found device.
  I called support for the external hardrive, who said this is an incompatibility problem and that I would need to re format external hard drives (and therefore lose all about them unless I copied them on a compatible hard drive).
  Is this true?

  Rather than go through the hassle to copy all data to another hard drive is there a way to make my new computer compatible with the external hard drive?

  Your help is very appreciated.

  See you soon,.

  Jason

  I have an old drive external HARD with images recorded on it and I use it for years with WXP, Vista, Win7 and now with Win8 too. There is no problem at all so I put t understand what could be wrong with your HARD drive.

  Do you have similar problems with other external devices connected to your laptop Portege?

• Why do VPPS apps show as not not transferable device when buying as Distribution managed?

  Hey people,

  I am using Meraki MDM and have been for some time.  It's the free version, but not the legacy version, the license has been upgraded.  I bought about 70 applications through VPP, many of them being free applications.  As with all free apps purchased via VPP, they were purchased as Distribution managed, which is what I want for the assignment of device to iOS 9.2.1 iPad air.  All purchased applications, with the exception of 3, were sent to the required devices without any problem.  There are 3 applications that have still not been sent on other equipment.  Here are media monkey, our history for the iPad and the App of poetry.

  I have no idea why these applications cannot be postponed to the devices, with the exception of the fact that the developer has not activated device allocation for these applications.  Anyone know if this is the case, or if there is no other reason?

  I've been with MDM iPads since iOS configuration 6, so I am very familiar with the process.  In addition, apps that have properly been eliminated, have the same settings applied in Meraki MDM.

  Any thoughts would be appreciated.

  Kind regards.

  Well, I just thought about it.  In the VPP store, when you are going to purchase history, and then click the app in question, when you are on the page for this application, you can scroll down and on the left side, since where it says 'See in iTunes' in a blue box, you will see whether or not it is said 'Programmable device'.  Bingo.  So, even if you can buy the apps like managed distribution, it does not necessarily mean that they can be assigned to the device.

• Hello! If I icloud library disabled, will be always saved pictures? I know that your backup stores the photo library of all devices and because I'm not all devices to be synchronized I think I'm safe and won't lose my pictures/videos. Right?

  Hello! If I icloud library disabled, will be always saved pictures? I know that your backup stores the photo library of all devices and because I'm not all devices to be synchronized I think I'm safe and won't lose my pictures/videos. Can someone please clarify?

  If you want your photos backed up, you must import them into the photos on the computer application that synchronize you with. iCloud photo library is a repository for all the photos for a given iCloud ID. However, it is not required for the care of your photos. I do not use iCloud photo library - import my photos into the library of Photos on my Mac.

  A backup of your device iCloud will save your current film, but if you remove anything from this film, then it will not be available for retrieval at a later date, because backups replace the previous backup version. A backup is so not an archive safe for your photos or videos.

  Photo stream keeps the last 30 days or 1000 photos taken with your camera if you have Photo Stream on, but once again, it's a temporary storage that gets crushed. Photo stream is intended to provide a method of sharing photos between the signed devices on the same iCloud account, but is not intended as an archive.

  Import your pictures and videos on a computer means that all photos and videos are kept in a library on your computer and will be accessible. It is the only safe way to archive your photos:

  PHOTO IMPORT IOS ON MAC/PC

  Good luck

  GB

• Satellite Pro L10 - USB port will not recognize devices

  Hello

  I got a L10 for 18 months. Under the guarantee, I got a replacement motherboard mounted. Everything has been ok so far. A USB port will not recognize devices, a port is ok, but randomly turns off a device attached to it and comes up with the message "USB device not recognized". The third port is ok all the time.

  Any solutions or suggestions?

  Post edited by: caddy

  I guess there is not enough power on the USB ports and external devices may not work correctly. It is not easy to say why this happens, but there may be a problem of welding.

  I recommend you contact the service again as soon as possible.

• Bought a second hand iphone 5 and my seller did not remove device to find my iphone and im too poor to buy a fresh iphone and my country does not have a retail store, so how do I get it removed icloud? Its imei is *.

  Bought a second hand iphone 5 and my seller did not remove device to find my iphone and im too poor to buy a fresh iphone and my country does not have a retail store, so how do I get it removed icloud? Its imei is *.

  Nobody here can help, and Apple will not help you to overcome the blocking of activation.  If the seller does not cooperate and remove the unit from their iCloud account, then you will never be able to use this device yourself.

  See disable find my iPhone Activation Lock - Apple Support

• Pavilion network adapter are not not in Device Manager

  My Pavilion P6330f lost the internal network adapter (no internet connection, adapter are not not in Device Manager).  Is it possible to re-restore/refresh it?  I tried to do a scan to refresh hardware, but it doesn't show any internal network adapter.

  I was able to get back on the network by installing a wireless network adapter via the disk support provided with the wireless USB device and using Device Manager.

  It seems that the internal NETWORK adapter has gone (fried) and I need to install a new NETWORK adapter in one of the expansion slots.  Other options?

  Is this a common problem?

  D.

  No, it is not common, unless your home has experienced a surge\dropout of power or a bolt of lightning. What you are experiencing, this is usually the result of thet.

  Since your office worked five years ago, he certainly provided you a reliable service. You might consider looking for a PC replacement in 2015. SCP last usually about five years before replacement is required.

  Wireless, it's that a good option as no extra wire is a good thing.

• I have a PC brand new - HP and played Chess Titans. Now all of a sudden it says it cannot find the texture, but he said no zero the reference count and then could not find device 3D.

  original title: Chess Titans

  I have a PC brand new - HP and played Chess Titans.  Now all of a sudden it says it cannot find the texture, but he said no zero the reference count and then could not find device 3D.  What's past and how to fix this.  Thank you.

  These error messages can occur if you (or software) also disabled Aero. Aero must be on (and supported by the video card) to play Chess Titans. "192GO should be enough for everyone." (of the miniseries "Next generation jokes")

• PXI-4072 can measure a pulse width?

  Can I use a pxi-4072 DMM to measure a pulse width? With the help of labview8.6.1 can I get period information and freq but I am interested in duty cycle. Thank you, Kenneth

  Hi Kenoss,

  If you use the PXI-4072 to acquire waveform data, then you can try to use the Measurements.vi impulse to get the duty cycle.

  

  Best regards

  Tony_G

• USB ports power your equipment, but not recognizing devices

  I started my pc yesterday (21/02/10) - for the first time since the incident of the blue death screen has resolved on 10/02/10 (see 'recent history of the problem' below). I got a screen that says "volume dirty cleaning in 3 steps" or something like that. Subsequently, the windows starts fine but the USB ports stopped working.
  

  All 3 USB ports are now fueling your equipment (confirmed by my laptop fan) , but none of them give me access to any external devices as my flash drives.

  Note: I didn't say "" do not recognize devices "and instead said"give me no access to devices "because when I plug in my flash drive, it is profiled as a material published by ususal Display icon at the bottom right of the taskbar." Of more when I try to eject the material, the flash drive appears as "Kingston Data Traveller". It's simply not let me access the flash player - instead when I click on the flash player icon (drive F :) it asks me to format the drive before using.) But then when I am trying to format it says that "windows cannot format the device."

  [Please note that the USB ports are all works perfectly between these two dates.] In addition, I did not any changes, hardware or software, recently. ]

  Recent history of problems (might be useful):

  I got a blue screen of death problem 2 weeks after I had installed Windows XP updated 09/02/10. I could solve this problem by uninstalling all the following patches: KB978262, KB971468, KB978037, KB975713, KB978251, KB978706, KB977165, KB975560 KB977914. (as suggested in the forum: http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/73cea559-ebbd-4274-96bc-e292b69f2fd1)

  After that I do not start my PC, until yesterday. It is the problem of the USB to start.

  Hello
  ) not a bad answer, but a lot of work and you can make mistakes
  make a sfc/scannow, as indicated here that it will reinstall missing and corruption of files http://www.updatexp.com/scannow-sfc.html I also noticed in your answer "dirty volume in 3 steps of cleaning" is you have using a kind of cleansing software registry cleaner etc. Registry cleaners that aren't much good for the most part and they will mess up your computer...
  If you do not use a cleaner that get some anti malware software download and run
  I left and use http://www.malwarebytes.org/ please click the checkbox as answered check on this Page if this post solves your problem, because it helps people who need quick access to answers THANKS AND GOOD LUCK

• Device Manager does not display devices

  Control Panel takes me to the MMC, but Device Manager does not display devices

  Hi Bandjo,

  ·         Device Manager is empty?

  ·         You have made any changes recently?

  ·         You have installed Windows XP Service Pack 3?

  Check to see if this article helps you.

  None of the items appear in the device list manager when you open

• Operating system recognizes is not USB devices

  Also having problems with USB devices not recognized, I tried all of the suggestion in the forum so far... 3 xs... unplugged, battery removed, even left on overnite... did not work.

  r.Unning Vista Home Premium on a laptop MSI M670, updated everything. Peripheral USB work in other PC, turn on in the laptop but the OS does not recognize devices, in Device Mgr shows 'no conflict', "the device is working properly", I uninstalled, disabled, etc. & reinstall Vista does not work, either. I must be a solution!

  The I get no message when the device is plugged... That is to say: the thumb drive.

  Hello

  If you have tried all basic troubleshooting and device is showing to work properly and no noise of conflict-it you may need to reinstall the USB controllers to recognize.

  To remove and reinstall all USB controllers, follow these steps:

  * Click Start, run, type sysdm.cpl in the Open box, and then click OK.

  * Click the Hardware tab.

  * Click on the Device Manager button.

  * Expand Bus USB controllers.

  * Right-click every device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  Restart the computer and reinstall the USB controllers.

  * Plug in the removable USB storage device and test to make sure that the problem is solved.

  Reference:

  http://support.Microsoft.com/kb/310575

  Hope this helps,

  Steve <> Microsoft Partner

• 4.8.5 WDM not finding devices

  4.8.5 WDM not finding devices

  Recently, I replaced my WDM 4.7.2 existing environment with new hardware and OS.

  My new WDM environment works WDM 4.8.5 on W2K8 R2 (64-bit).

  While some devices check in I'm going to have trouble finding other existing devices of all the different models of Wyse (S10, V10, 1125) and 1200LE

  I know there is a version of WDM 4.8.5 HAGENT requirement but the terminals I meet the minimum reuquirement haven't checked that I was expecting.

  I have run a few network traces and that you can see one of the incriminated having a conversation with my new WDM server, but I see a query error incorrect HTTP 400 - invalid verb in the trace.

  Anyone can shed some light on this?

  Thank you

  These former clients use a verb SET to start the communication which was hosted in IIS6.  IIS7 on Windows 2008 R2 will not reject authenticated PUT verbs for safety.  If you can rewrite PUT it at GET say with a URL rewriting done using a VIP on an external device, you can make them work.  This rejection is by http.sys which runs at the kernel level, so you will not be able to rewrite the verb on the server itself.

  Thank you.