License server issues

Similar Questions

• Issue of license server

  We are wiping and rebuild our vCenter and I had a question about licenses.  At present, our license server is on the same server as the server vCenter, and who will be wiped clean so we can install server 2008 x 64.  When we take this down to rebuild it, I am not mistaken, we have a period of 14 days to operate our system of VMware without the license server until we can put on the new vCenter 4.1 Server licenses?   Thank you.

  If you migrate to vSphere 4.1 Why not consider a virtual vCenter in this way your current infrastructure is not affected during the migration.  virtual vCenters are entirely taken in charge and actually offer a greater level of resilience as a physical

• Weaning to a license server shutdown

  Hi all

  I need to take one of my devel completely off-grid system. I usually use a license on site for all products of NEITHER, but he will not be able to contact the license server. I remember there is a way to get or to generate a license for use offline file, I did a few years back. Can anyone tell me the correct procedure, thanks.

  PS: just upgraded to 2013sp2, where is the list of changes?

  Hello gdargaud,

  I think that what you are looking for is a disconnected license.

  Getting Started with NI VLM - create a disconnected license or at home

  http://digital.NI.com/public.nsf/allkb/3BF6EE92ADDC036C862572A300732E00

  Please contact your administrator for server on this subject, because he is the one who will be able to generate this for you.  In addition, your question is technically a volume license manager issue, then you might find more luck if you find that you have additional questions on the subject to the search on these forums.

  Best wishes!

• Local server connect to a domain license server

  I have a server terminal server running under windows 2012 locally (domain a)

  My license server is running on windows 2012 arrived in the area. Forest mode

  I try to establish a connection between the 2 of them and it fails.

  ***

  To identify possible licensing issues, the administrator for the server monserveur.com license credentials are required

  ***

  When I provide a credentials area, it works and it reboot after failure. (No domain server)

  I even try to use a local (not domain) administrator account to connect to the license (supported in domain) server and fail too.

  I have no problem if you are using windows 2008.

  Anyone experience this before?

  Thank you

  Rgds

  Wang

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• I have a ts 2008 license server with 90 per available user licenses (21 already issed). However, users get a message that says that there are no licenses available

  I have a ts 2008 license server with 90 per available user licenses (21 already issed). However, users get a message that says that there are no available licenses. The TS are iss device by installing licenses. Local group policy is not configured on each ts. The strange thing is that I can't find the option to license type within the domain group strategy, however, I suspect that this is the problem as when I go through the configuration in the RD Licensing Manager system indicates that the license server will be able to issue per user Cal. If anyone has had / overcome this problem I would be very gratefull to know the solution. Best regards Steve

  Please repost your request in one of the most appropriate Microsoft Windows Server Forums, thank you!

• ADE 2.0 and 4.0 do not work with Windows 10. The next problem is generated when you try to download a book from the public library.    Error getting License Server Communication problem E_ADEPT_DOCUMENT_OPEN_ERROR.

  The next problem is generated when you try to download a book from the public library.

  Error getting License Server Communication problem E_ADEPT_DOCUMENT_OPEN_ERROR.

  The work around works of Jean.  It would be nice if Adobe provided a real difficulty however.

  I have ADE installed 4.03.  The problem will occur as soon as that ADE is closed and reopened.    It takes so the patch every time allows you to download a book ADE.

  1. for Overdrive - select a book and click Download. -pop - up - select - Save file. - under the open with select - acsm_auto_file - download the file of social mobilization in your download directory.

  2. expand the Explorer open the file - go up to the OS (c)-

  -go to Program files (x 86) - enlarge

  -to enlarge Adobe

  -go to Adobe Digital Editions and the left click.

  -On the right part of the screen right click on Digitaleditions.exe.

  -Pop - up menu - on the left, click PROPERTIES

  -Pop up to select COMPATIBILITY

  -at the top of the menu compatibility, choose the resolution of compatibility issues run

  -Pop up to select the troubleshooting program

  -Pop up choose the program worked in earlier versions of windows, etc.

  -on the left, click NEXT

  -POP up - which version etc? Choose that I don't KNOW

  -on the left, click NEXT

  -POP - up - left click Test Program-

  -AT THE TOOL Avantek of window screen, a FLASHING ICON will appear - left-click on the icon - a pop-up will ask you if you want this program to change etc. On the left, click Yes.

  3. ADE open - make sure ADE is in library view.

  -Left click on FILE and then select Add to LIBRARY from the menu drop down.

  -POP UP - down to the right to choose the type of file of social mobilization

  -left side of the pop up to choose the directory where you downloaded the file of the CMHA.

  -Select the file of the CMHA in the right side of the window and on the left, click OPEN

  -It should work, but you have to go through the whole routine if you close ADE.

  I HOPE ADOBE will solve this problem. With each update of Windows 10 ADE seems crumbles a bit more.

• License server problem

  Hi all:

  I installed the update of the vCenter Server 3, all licenses come correctly but not the server VC itself given that a big red "Days left" count down in the upper right of the screen VClient

  I checked the license server, given the "PROD_VC" is saved correctly, but some how it's not went to VC Server

  WKVC25-u3: license server UP (MASTER) v10.8

  Demon provider (on WKVC25-u3) status:

  VMWARELM: UP v10.8

  Info according to its use:

  Users of PROD_VC: (Total of 1 permit;  Total of 0 licenses in use)

  Users of PROD_ESX_FULL: (Total of 6 licenses issued;  In total, 1 license in use)

  V2005.05 "PROD_ESX_FULL", the name of the seller: VMWARELM

  floating license

  root esx35u3-201.ent.workzone.com/dev/tty (v2005.05) (WKVC25-u3/27000 101), start Wednesday 5/20 15:11

  Users of ESX_FULL_BACKUP: (Total of 6 licenses issued;  In total, 1 license in use)

  V2005.05 "ESX_FULL_BACKUP", the name of the seller: VMWARELM

  floating license

  root es5u20.com/dev/tty (v2005.05) (WKVC27000 201), start Wednesday 5/20 15:11

  Users of VC_ESXHOST: (Total of 6 licenses issued;  Total of 0 licenses in use)

  Users of VC_VMOTION: (Total of 6 licenses issued;  Total of 0 licenses in use)

  Users of VC_DAS: (Total of 6 licenses issued;  Total of 0 licenses in use)

  Users of VC_DRS: (Total of 6 licenses issued;  Total of 0 licenses in use)

  can you give me advice

  Thank you

  see this KB, http://kb.vmware.com/kb/1006561 , it may be useful

• ESX Server timed out when I try to enter the license server in the CR

  Hi all

  I have a problem with the addition of two new ESX servers in our virtual Center.

  Let me give you a brief overview:

  We have 5 servers ESX and virtual Center Server.

  All servers are in a single Cluster (Cluster 01)

  Now, we want to use Virtual Desktop Infrastructure and for this reason, we bought another 2 servers (blades).

  I installed from scratch with ESX 3.5 Update 4.

  I did a second Cluster in our VC (Group 02) and add the two.

  I configured the network settings and storage, everything went very well, shoot when I want to point to our license server, whenever I get an error message from our VC. Operation timed out and my settings when not accepted. No matter if I get the IP address or FULL domain name. BUT I can ping our server to ESX Server licenses, so I'm not sure if this is some sort of DNS issue or not.

  Another note: our first 5 ESX servers where ESX Server Standard license.

  Our new ESX servers where an ESX Server VDI license. I used the CD to install ESX normal, because I have not found any VDI install special files.

  I see all licenses in the Administration view in our VC, so I think our license file is not corrupted.

  Things I've done so far:

  Renewal of license, start stop server, esx Server license installed twice from scratch

  I have no more ideas, I hope someone could help me with this problem.

  According to your image, you have 0 agent licenses virtual centre-left to allocate to new hosts.  What might happen, is that the agent is not properly installed on the new servers.  Connect to ESX servers.  Make sure that you can test the virtual Center by domain name server FULL and hostname, not only by intellectual property.  From your RESUME, ping your esx server fqdn and the host name.

  Also, check the file/etc/hosts on your esx server and make sure that the entries are tiny.

  -KjB

  VMware vExpert

• Virtual Server Center down and as its also the license server, it cannot start

  I have the virtual center server which is also the license as a virtual machine server. We had problems with the SAN today and decided to move this server to local storage in the case of other issues during the weekend, until we can diagnose/solve the problems of SAN. However, it will not start back up to stop the virtual machine to move (no installation storage vmotion again) and complains that cannot see the license server, the license server's so how can we start it?

  I tested stop this server before and to work around the problem, then we have just activated evaluation mode, the server restarted, and he returned to the license server mode when it was high, but he used to do that now and I can not start any vm at all and since most of them failed because of problems with SAN storage I need to get this resolved as soon as possible. The difference between when we tested before and now 4 months and update 3 has been applied recently.

  How do I start the server in its current or is configuration - it is no longer possible to use the evaluation mode and we do the licensing of other words, IE non-virtual?

  ......

  I managed to start the server using VM Player running in another physical server, but this is not an ideal long-term solution, but out me an affair until we solve this problem.

  Many people run in this mode.

  As a backup, just getting up an another license server using your existing key.  Point the ESX host with virtual machine on it to the 'temp' license server by connecting to the host ESX directly with the VI Client.

  Back up the virtual machine.

  Change license server address that you modified on the back of ESX host.

  Jase McCarty

  http://www.jasemccarty.com

  Co-author of VMware ESX Essentials in the virtual data center

  (ISBN:1420070274) Auerbach

  _{Please consider awarding points if this post was helpful or appropriate}

• LabVIEW / TestStand ignores license server settings

  Hello

  I see a rather odd behavior on my computer. We received a new license file to our license server. Once it has been imported, TestStand and LabVIEW used of temporary licenses... I ignored it for a day, but became suspicious.

  The Manager of License tool on my computer detects only the license server and properly displays the access rights for my Suite of Dev (incl. Automated test). LabVIEW and TestSTand can check a property...

  Instead, I get the error message

  LabVIEW development system

  License attempt 1:
  All the available licenses on 'xxx' are currently extracted. (NILM13)
  If you have any questions, contact your license administrator.

  Shows available licenses however License Manager. I already tried to reinstall software of NOR (took awhile...) manually remove, add license server information. I'm getting a little desperate / annoyed.

  Any ideas?

  See you soon

  Oli

  Fixed a problem.

  After the stop & a few reboots of license server, my license works again.

  Seems, it was a "personal matter" between me a license, since only my license server refused to work...

  Enjoy the weekend!

  Oli

• Get the name of the network license server automatically?

  Is it possible, perhaps by means of Windows Script, to get the name of a computer is currently using the license server?

  Hi Rose Dalban,.

  You can know which servers a computer turns to the registry HKEY_LOCAL_MACHINE\SOFTWARE\FLEXlm Manager\NILM_LICENSE_FILE license key

• Different PC user name to the user license server names

  Hi all

  I encountered the problem that on some PCs running with a goal of training of RPF of generic user account, the License Manager will not grant one of my licenses in volume. How can I get LabVIEW to communicate with the license server with a different user name for the windows login name? I already tried tools--> user name, but it has not fixed the problem.

  I'm always under 8.2.1 on these computers.

  Concerning

  Oli

  Hi Oli,

  You have licenses based on the user or computer
  licenses? From your description, looks like you have several
  licenses based on users and multiple training computers where windows
  usernames are all identical. Is this correct? If that's the case then
  You should be able to grant a license in volume for this username but it
  you won't concede more than one license under the same name. Change
  LabVIEW settings will not solve this that this problem concerns more with Windows
  and VLM. To resolve this problem, you can either go in windows and create
  new usernames or you can call and we could you spent to get
  computer license and you should be good to go.

  Lars

• Terminal server licensing server

  We have 2 licenses of cal ts on windows 2003 server we can only get a pc branch to open a session with the new ts win 2003 installed. I installed the windows 2003 ts to
  see the windows server 2003 license server. What do I need to uninstall the old ts 2000 until I can get the desktop pc 2 branch to see the new ts.

  concerning
  Matthew

  Please transfer your inquiry in the most appropriate in the Windows Server Forum.  Thank you!

• Video conference will operate without a license server TP and conductor?

  Hi all

  We need POC for video conferencing with Cisco Jabber on desktop. The scenario is similar to that we have CUCM 10.5 running in the trial license and server TP and TP driver running on the virtual machine without a license.

  We will reach videoconference without license server TP and conductor?

  Thank you & best regards

  Louis Nithin.

  Conductor Essentials can run without licenses, it offers all the functions of conductor but is limited to 1 bridge Conference and no grouping, refer to table 1 in the conductor datasheet for more information.

  TelePresence Server requires licenses to operate, you will need to purchase a license for the software, so it can be activated, as well as wallpapers or multiparty license licenses.  Screen licenses are per participant and installed on the telepresence server itself, while the multi-party licenses are either user or conference of base that are installed on the conductor.  Refer to the presentation of the product just above 1 Figure in the data sheet of the telepresence Server about the screen and the multiparty licensing options.

• license to make mistake.  Communication of license server.  problem already fuflfilled by another user.

  license to make mistake.  Communication of license server.  problem already fuflfilled by another user

  Hello

  Could you please develop your problem because we know not?

  Kind regards

  Sheena