LifeCam Studio on Windows XP SP3 problem

Similar Questions

• Windows XP SP3 problems

  I am running VM Ware Server 2 on a Windows Server 2003 computer that is connected to a concert. When I build my virtual Windows XP SP3 it connects only to 10 MB. Any suggestions?

  Thank you

  Have you installed the latest version of VMware Tools? I have version 2.0.2.1 of the vmxnet.sys and the Task Manager is visible as it is connected to 1Gbs. Note that just because it says it is connected at 10 Mbps, doesn't mean it goes faster than that since, as long as the physical NETWORK card allows, he will be not be forced by the driver or virtual hardware.

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• Not able to use Microsoft LifeCam Cinema machine Windows XP SP3.

  Original title: Cinema of cam Life, XP SP3 error report.

  I have installed the drivers and all, through failures 4 times now, and I always get an error report window when I try and open the "Microsoft Lifecam" app, it takes a few seconds as to try and connect and then an error report appears. I meet the system requirements, I don't know what to do at this point.

  Hi MalickDelorian,

  ·         What is the exact error message/code you receive?

  ·         Have you been able to use the Microsoft LifeCam previously on your machine?

  ·         What troubleshooting steps you tried to solve the problem?

  You can follow this link and check if the problem persists.

  Troubleshoot failures to find the new LifeCam hardware

  Reference: Troubleshooting, install the Intellipoint or IntelliType software, LifeCam.

  File of Microsoft LifeCam Readme and troubleshooting information

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer

• Windows XP SP3 problem?

  Hello

  We have developed a USB receiver of the material basis for the broadcasting DAB/T-DMB Mobile solution. This application will start receive the stamp of streaming via USB driver chipset.

  Real problem is when we used our command interface in Windows XP service Pack 3 has problems of overflow. (System could not read USB in 12 States delay buffer then overflow will have taken place. For the record, the system configuration is very high).

  If we use Windows XP service Pack 2 do not have overflow problems and the system works without any problem.

  Manufacturer of receiver and USB developer has no idea why this kind of symtom occurred in Service Pack 3?

  Kindly let us know any solution to this problem.

  Muru

  Hello thiyagan,

  Just to tell you it's Vista forums. You should redirect your question in the forums XP here: http://www.microsoft.com/windowsxp/expertzone/newsgroups/reader.mspx?dg=microsoft.public.windowsxp.general

  
  Make it a great day!

  "In the end the love you take is equal to The Love You Make" (The Beatles last song from their latest album, Abbey Road.)

• Cannot access my profile. (Windows XP SP3) Problem apparently because of Windows Installer.

  I can't connect to my profile, apparently because of a problem with Windows Installer.  It starts to open a session and when I try to access my documents I get a message unable to access my profile and if I'm logged a temporary profile: "Details: access to refusedowever, everything seems to be there, except for my usual wallpaper and I can access my files."  In the msconfig Services tab, Windows Installer shows as stopped. I tried to reinstall, but it won't download because of the error of windows install. The keyboard started to do fun things like key assignment got confused. My admin profile works except for the Windows Installer problem which stops remove me or update Java. I checked for malware and viruses (no) run "sfc/scannow" ad "chkdsk /f.  All system restore points are missing.  If I can access my files, the system asks me my first and last name and initials prior to providing access. I have now the temp profile open in safe mode and note that a file that I saved when you previously logged into the temp profile has been saved successfully to the new folder that I created. In addition, when you are connected to normal mode, I found that I couldn't access to Mozilla Firefox, open MS Internet Explorer and click on a link to something (can't remember what) and Mozilla Firefox open as usual.

  Things that I did just before this problem appeared: installed and run Malwarebytes and Superantispyware, tried to update Java and VLM Media Player using AVAST! interface, and then without using AVAST! interface. Both failed, but something else I've updated OK. Tried to download and install Windows Installer 4.5 (without success). So I then tried to repair/reinstall command of the race by using regedit and regserver command screen.

  I wonder whether to follow the instructions in http://support.microsoft.com/kb/322756. However, as it asks me to back up the registry before you edit it. As all my previous restore points disappeared, I don't trust to back up the registry. How can I back up the registry of my external hard drive?

  You have a damaged or corrupted user profile.  A way to recover from this condition is to perform a system restore, but since you have no restore points, you will need to recover with another method.  The usual way to recover is to create a new user profile and then copy the data from the damaged to the new profile user profile.  This procedure is not usually difficult.  Choose from the selection below:

  "How to recover damaged Windows XP user profile"

  <>http://support.Microsoft.com/kb/555473 >

  "How to copy a user profile data damaged to a new stars in Windows XP"

  <>http://support.Microsoft.com/kb/811151 >

  Almost always, corruption of the profiles is accompanied, otherwise caused corruption in the file system.  At an ideal time, it is strongly recommended to perform a 'chkdsk' operation with the "/ R" or "Repair" option.  Note that this operation will take place at the next reboot before Windows loading completely, cannot be interrupted and can take more than a few hours depending on the size/speed of hard disk and the number of errors found...  Sometimes, this in-and-of-itself can solve the problem.

  "How to perform Disk error in Windows XP check"

  <>http://support.Microsoft.com/kb/315265 >

  To answer your question on the backup of your registry - try the freeware "C:\WINDOWS\ERUNT" to create a backup.  It has been used and recommended in this forum for years.

  C:\WINDOWS\ERUNT: <> http://www.larshederer.homepage.t-online.de/erunt/ >

  HTH,

  JW

• Impossible to install the Lifecam cinema on Windows XP SP3 software

  I can't install the software on my Windows XP machine.

  I get the following error:

  Microsoft Visual C++ Runtime Library

  Program:... UME ~ 1\Paul\Local Settings\Temp\LifecamSetup\setupstb.exe

  This application has requested the execution in an unusual way.
  For more information, contact the application support team.

  Ok

  ___________________________________________

  I tried everything I could find on the internet and I get the same error!
  Microsoft wants an identification number of the software product, which I don't know, because the software will not load.

  Any advice would be greatly appreciated!

  PS: I don't have any problems to load the software on my Vista 64-bit.

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• Install LifeCam Studio offline

  I have recently loaded several LifeCam Studio webcam on XP SP3 machines installation.

  However, the only problem that occurs is that the installation wants to an available internet connection to install the necessary drivers, even if I download the executable file of the product support page.
  There is workaround to allow offline installation? The customer that I install these cannot allow an available internet connection on these machines, for security reasons.

  Hello

  Installation requires Internet access to connect to a specific server from Microsoft.

  See the link.

  http://support.Microsoft.com/kb/973297

  See also the link.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/LifeCam-cinema-installation-with-no-Internet/2383270b-5080-4ace-AAE8-972007fd0f07

• lifeCam Studio Window xp SP3 Mic works only half way thur video recording

  My new webcam works fine on Skype for the photo and the microphone, but when I run a video of my grandson little, the image in the back room is very good.

  but the voice is only heard part way thur, setting on 640 * 360.  Thanks for any Help Window XP Sp3

  Hello

  1 how long have you been faced with this problem?

  2 have you made changes on the computer before this problem?

  3. are you watching a recorded video, or you are on a video call with your grandson?

  Answering these questions could help us help you better.

  You can also try to contact Skype support team to help on this issue.

• LifeCam Studio must adjust settings to each Windows session

  Each time before use twinkle 'Lifecam Studio' I have to adjust all the settings like Zoom, 50/60 Hz and others...

  Savings by apply and OK is effective only during the Windows session...

  Is there a way to save these settings to a new desired adjustment? ...

  Thank you Jaime

  Hi Jaime,

  Thanks for the reply.

  We are happy to know that your problem has been resolved.

  You are always welcome in our community for other issues related to Windows.

• Problems on Mac OX 10.6 V.S. Windows XP SP3

  Hi all

  I have a problem with my MacBook Pro.

  My system is Mac OX 10.6, but I use BootCamp to 10.6 to implement the portable Windows XP SP3 on the same computer. Then I put in place LabVIEW 8.5.1 on Windows XP system and use Agilent 823578 USB/GPIB Interfaces to communicate with locking SR830 amplifier.

  When you use Angilent connection Expert, I could communicate with SR830 by Agilent 823578 USB/GPIB Interfaces. However I couldn't use relative visa in LabVIEW command, such as opening VISA, to connect with SR830.

  On the other hand, I use the same program on the DELL Windows PC to communicate with SR830 without any problem.

  So I was wondering is it a problem of compatibility of MacBook Pro and Mac OX 10.6 with Driver of instruments?

  I will be appreciated if someone could help me to solve my problem. Thanks to you all.

  First, you must enable support for Tulip so that MAX recognizes the controller of agilent. In MAX, you select NI-VISA under the software section. Click on the visa, and then under MySystems Options > General settings, select passports. Check the box for NiVisaTulip.dll. If you do a view > refresh, the controller must be included so that you might have to restart. When MAX lists the agilent controller, you should be able to scan for instruments. It's what will update the visaconf.ini file.

  I'll sort of memory on it and have only done on windows pc. I don't really know if there are problems with it under a virtual machine on the Mac. There are numerous links on tips related to the use of controllers of agilent with LabVIEW so you can do a search to see if I missed the details.

• problems of xbox 360 with windows xp sp3 wireless receiver

  problems of xbox 360 with windows xp sp3 wireless receiver

  Hi Frank Lucas.

  (1) if it works well before?

  (2) remember to make changes?

  (3) you get an error message?

  You can see the steps outlined in the article below

  Troubleshooting your Xbox 360 Controller for Windows

  http://support.Microsoft.com/kb/908888

  You can also post your query on Xbox Forum

  http://forums.Xbox.com/

• Microsft LifeCam cannot be installed on Windows XP SP3

  Hi, I am unable to install Microsoft LifeCam 3.5 on Windows XP SP3. This is the error I get when installing

  -------------------------
  Microsoft LifeCam
  ---------------------------
  Cannot install the Microsoft LifeCam software when connected as a built-in guest user
  ---------------------------
  Ok
  ---------------------------

  I get this error despite opening a session with the "Administrator" account or any other account with administrative rights.

  On my system the solution has been to start services Fast User Switching and Terminal Server Services. I had turned off as a matter of hygiene (I use nothing that they support) but in this case, they had to be running. I suppose that for some reason the Lifecam Installer wants to use alternative credentials. Hmm.

• Performance IEEE 1394 Windows XP SP3 Adobe Premiere 6.0 problem

  I'm trying to capture video using Adobe Premiere 6.0.  When I got Win2K installed it worked fine.  I have upgraded to Windows XP SP3 and first stopped working properly.  A clean installed Matrox RT2500 - it's the video capture card, I bought with the kit Adobe Premiere - according to the instructions, as well as first - including the 6.01 update.  Now when I connect my Sony DCRTRV520 camcorder via firewire IEEE1394 and try to capture the Hi8 video I recorded, it won't record a few frames, then stops.  Matrox video tools say that the IEEE 1394 device has stopped working.  First capture options indicate that the camcorder is not recognized.

  I found a forum which indicated that the problem was with XP sp3 drivers for Texas Instruments OHCI 1394 device - indicating that the sp2 and sp3 downgraded the 1394 to S100 speed device performance.  I found an article in the database saying MS was aware of the problem and finally got that to work (KB885222) download

  http://download.Microsoft.com/download/9/0/6/906f2f67-39c4-48bc-8558-86833d4cbc16/WindowsXP-KB885222-v2-x86-enu.exe

  It will not actually install on the PC I am running SP3 not SP2.  It's really frustrating because the system worked very well under windows 2000. Even worse since I have a lot of old video - not stored on DVD or transformed into films which I was hoping to work for presents for the family, this Christmas.

  Anyone know of another - hotfix - download or similar which will fix this problem?

  Hi John,.

  Thanks for posting in the Microsoft Community Forums. I suggest you post this question in this forum for better support.

  http://social.technet.Microsoft.com/forums/en-us/category/windowsxpitpro

• Error message "the website has encountered a problem and cannot display the page" when you try to install Windows XP SP3 update

  Original title: cannot use Windows Update to install Windows XP SP3

  I have done a complete reinstallation of Windows XP Pro from the original disc and managed to update to SP2.  However, when I tried to upgrade to SP3, I got an error that "the site has encountered a problem and cannot display the page.  I tried all the suggested fixes that I can find.

  During the last attempt, I discovered that several dll is missing.  Here's the msxml6.dll, wups2.dll, c:\windows\system32\wucltux.dll and c:\windows\system32\wuwebv.dll.  If they are critical, where can I find them, and how do I get support.

  In addition, mshtml.dll is available, but the DllRegisterServer could not find an entry point.  Is this critical?

  In any case, I still can I install Microsoft Update or download/install SP3.

  The computer is an IBM R50e laptop.

  Thanks for any help you can give.

  Try to run this tool to windows update. This will help to re-register the dll

  After its done. try again and do the update

  hope this helps

• I am also having the same problem with the same updates. I have Windows XP SP3 and it's updates with the problem.

  I am also having the same problem with the same updates. I have Windows XP SP3 and it's updates with the problem.

  Security Update for Microsoft .NET Framework 2.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2572073)
  A security update for .NET Framework 2.0 SP2 and 3.5 SP1 on Windows Server 2003 and Windows XP x 86 (KB2518864)
  Security Update for Microsoft .NET Framework 2.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2633880)

  They all install properly but switches back to windows update to install. It's some kind of loop.

  Hi billy73,

  In addition, if you still have questions, please take a look at the thread similar here with a solution as possible.

  I hope this helps!