Light of Smartphones Trackball blackBerry does not?

Hi, but I have my first BB 8330 last night... am trying to get used to the features every hour, I have a new question, but my only is right here:

The curve trackball is apparently supposed to light up?  Is this correct?  I didn't until a colleague told me about it.  Mine is not on... is there a way to control it?

I have Auto-dim active and works very well.  Brightness of the screen also works.  Keyboard also lights up properly. I had serious questions to Desktop Manager, work last night so I downloaded and installed the latest version and everything goes very well, but no trackball light.  I remember never work.

Maybe a setting I'm missing, or a default unit?  Any help would be greatly appreciated, these forums are a wealth of knowledge, I have already learned so much just in one day to my questions by searching.  Unfortunately impossible to find an answer for this one.

Thank you.

Hello and welcme t Frums!

 

 

The trackball and keyboard only light up if the sensor will capture it's dark. Try to get your hands on the top of the unit and see if the trackball lights up.

Tags: BlackBerry Smartphones

Similar Questions

  • the light on the power button does not work. How can I activate it?

    HP pavilion dv7

    Windows 7.

    the light on the power button does not work. How can I activate it?

    If the key light is not lighting up, then more than likely that the LED is just out for your power button. If the laptop is still under warranty, you can it be repaired or replaced, but as long as its not causing you any serious issues, I worry too much with it.

    BRAVO is just a system we use to say thank you to informative messages.

  • no lights after paper jam, printer does not

    no lights after paper jam, printer does not

    John, thank you very much, found that when the paper through the printer offline mode, I put on the line, then reconnected to electricity, and she came back.

  • Light (switch) on my screen does not turn off. I have to shut my computer down several times a day to turn off the monitor.

    Light (switch) on my screen does not turn off.  So, I shut down my computer and restart several times a day, because when I put it in mode 'sleep', he wakes to the top in a few minutes and will not fall asleep.  I could put a blanket on my screen when not in use, but I'd rather find a way to make it stay asleep when I tell him.

    Light (switch) had already done once before and I was so worried that once I turned off the monitor that I would never get it new on... a bit short of money here, to buy a new monitor, but the next day, I pressed the power button with an additional downward pressure and I could so he could start working again (able to turn the market monitor).  It was about 3 weeks ago.  Now, the light stays green, unless I stop the whole computer.

    Maybe my main problem is sleep mode, which removes the screen for like 2 minutes and then he wakes up to the top and is so rude when I myself and try to sleep, I just turn off the monitor everytime I put the computer to sleep.

    Now, I can't turn off the monitor, except by turning off the computer.

    Hi JDandGinger,

    I suggest you follow the provided article and check if it helps.

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-power-problems

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-monitor-and-video-card-problems

    If the problem still persists contact the manufacturer of the monitor for more help and information.

  • Why blackberry does not support flash?

    Why blackberry does not support flash?

    We do it.

    
    

    You can activate it in the browser via the settings menu. As you have probably heard talk, Flash is going by the wayside in favor of a successful solution of non IE: etc. of audio/video/Web HTML.

  • BlackBerry Smartphones my "BOLD" does not work from... Help, please

    Hello, I have a Blackberry 9000 "BOLD" device. last day, when I changed my SIM card & put the battery on the starting point, is not starting at all.

    When I put the battery, the red light is on during approximately 10 seconds (without flashing, right now) then after a few seconds the white screen comes with the loading circle... and then set turns off and the red lights again.

    Its like light - red > white screen > light > white screen >...

    I tried many times, but it does not solve. I removed the battery for hours more, also same result. I connect it to the pc with USB, but it does not and PC also does not find the device. BlackBerry Desktop Manager failed to connect with him. How to fix it... Please help me... I have a lot of data in it. In any case, I have to start for once...

    The red light still flashes? Do you see anything on the screen?

    Try to reload the software on the BlackBerry using the article below.

    KB10144 - how to force detect the BlackBerry smartphone using the Application Loader

    Thank you

  • BlackBerry 9800 Smartphones Touch screen does not

    as mentioned in the subject

    am having a problem with my torch 9800 sensitivity to the touch screen does not work. I tried formatting than her apps, but still nothing is happened

    also it restarts automatically several times and it is the fact that it is difficult to do something to solve the problem of the screen

    Please I need your help for this problem

    Try a battery pull if you please, with the BlackBerry device powered on, remove the battery 15 seconds and then reinsert the battery to reboot the device. This will clear all hide as restarting a PC. Then try again and see if the problem persists.

    What OS are you on? On your device, type a new message MYVER and a space after to see and report please.

    On device, go to Options, device, application management is a great way to see what your applications with your use of the CPU on Smartphone. Simply drag bar greater than CPU and see what happens. Also touch the CPU menu to see other time variables. I discovered that an application has been eroding CPU cycles on my own

    Disable Compression on the memory card? go to Options, device, storage

    using a custom theme? Try it for a day that factory by default to avoid your theme

    remember the ESC key to close most applications, with the exception of GPS and some chat clients. other applications must use the menu and then exit or close. The key furthest to the right is a key to the House and does not close on its own apps, but will put an end to the calls.

    If the above does not work then maybe in running a new OS is in order.

    Manual device OS upgrade instructions:

    1. start by searching for your operator and the system operating file that you want to use.

    http://NA.BlackBerry.com/eng/support/downloads/download_sites.jsp

    2. make a backup of your device first, using Desktop Manager > backup. Close at the end Office Manager and disconnect it from BlackBerry. Get DM here http://us.blackberry.com/apps-software/desktop/

    3. download the OS files to the PC then install on the PC by running (double click) the downloaded file.

    4. go into c:\program files Research in motion\apploader and delete the file named "vendor.xml."

    5. This step is not necessary unless there is a problem on the next steps. Use BBSAK from BBSAK.org and wipe the device (after doing a full backup), then after you get the 507 error (no OS installed) then proceed to step 6

    6 remove the internet connection for PC and reboot the PC.

    7. plug the BlackBerry and double-click on "Loader.exe." It is located in the same place as the above vendor.xml file was in.

    8. If you did step 5, restoration of the back upward. Follow this KB if necessary http://www.blackberry.com/btsc/KB10339

    Take advantage of the new operating system.

    If after all this then maybe you have a problem with your device and will need to contact the place of purchase if under warranty still.

  • BlackBerry screen Smartphones Torch 9850 does not turn

    Hello

    I got a new Blackberry Torch 9850 and noticed that the screen does not turn when the phone is held to the side. Compass calibrate as well.

    I have updated to the most recent software available - 7.1 Bundle 1737 (v7.1.0.580, platform 5.1.0.429).

    Did not help at all. However, I accidentally found that the screen turn to a landscape position if the phone is quite strongly shaken. So that means accelerometer should work somehow, simply not properly.

    Any ideas how to solve this problem?

    Thank you in advance.

    Hello and welcome to the community!

    Please try to start safe mode:

    • KB17877 How to start a smartphone BlackBerry in Mode safe

    You will take several attempts to get the combination of keys ESC (press/release/hold) OK, so be patient and you may need to try a few variations of what shows the KB. When properly in Safe Mode, see if the behaviour persists (I suspect it will, but it's worth the test). If so, then go back to your place of purchase or warranty provider that something is wrong at the hardware level, for which no amount of software, OS, or Internet-remote diagnosis can help.

    If the behavior does not persist in Mode without failure, then well... think what happened just before this behavior started? A new application? An update? A theme? Something else? Think carefully that the slightest change can be causal... and try to undo all that was.

    Good luck and let us know!

  • BlackBerry 8320 of Smartphones Software install - does not recognize port

    Try to download a software to save a 8320. Installation is fine (I disable the antivirus and run the file as an administrator to avoid any problem). It goes very well through the installation. To start the wizard and then the device-centric application, the first screen is the portal through which the device connects to the computer. The drop down menu is black and her box 'find the portal' is faded and cannot be used.

    I tried several downloads and several portals, but nothing changes this screen.

    I'd appreciate any help and thanks in advance!

    Hello and welcome to the community!

    Here is a list of troubleshooting items... I hope that something will be useful:

    • http://supportforums.BlackBerry.com/T5/BlackBerry-Desktop-software/tips-for-getting-BlackBerry-deskt...
    • KB10144 How to force detect the BlackBerry smartphone using the Application Loader
    • KB28457 BlackBerry Desktop Software is unable to detect the BlackBerry Smartphone because of administrative permissions
    • KB28458 BlackBerry Desktop Software is unable to detect the BlackBerry smartphone when user account control is enabled
    • KB28459 BlackBerry Desktop Software is unable to detect the BlackBerry smartphone when a full version of Roxio® Media Manager is installed
    • KB28456 BlackBerry Desktop Software is unable to detect the smart phone BlackBerry when the USB selective suspend setting is enabled
    • KB28444 The BlackBerry smartphone is not detected by the BlackBerry Desktop Software, when connected by USB to a USB hub or a docking station
    • KB28443 BlackBerry Desktop Software cannot detect the BlackBerry smartphone when connected via USB
    • KB02640 Troubleshooting USB connections
    • KB15486 Top 10 smartphone BlackBerry and BlackBerry Desktop Manager troubleshooting tips
    • KB00125 BlackBerry Desktop Software cannot detect the BlackBerry smartphone
    • KB11439 BlackBerry Desktop Software does not detect the BlackBerry smartphone when it is connected
    • KB00019 PIN code not displayed in BlackBerry Desktop Redirector
    • KB10938 "Current USB charge is insufficient," appears on the BlackBerry smartphone
    • KB01451 How to enable Sync advanced logging if a wired synchronization fails
    • KB19717 The BlackBerry smartphone is not detected as a USB mass storage device when connected to a computer
    • KB16310 Media Transfer Protocol and the BlackBerry Storm smartphone
    • http://supportforums.BlackBerry.com/T5/BlackBerry-Desktop-Software/Desktop-Manager-quot-disconnected...

    In addition, make sure you use only the root USB ports... without hubs (sometimes the front-end ports are hubs... use a rear USB port). And don't forget to try to disable the USB power management in the configuration of your system (Device Manager).

    Check also on the incompatible software... it was reported that NTI Shadow Ninja & software can cause a conflict; Remove and reinstall the desktop software BB allows to install correctly.

    My apologies in advance if this is redundant - there is no way to be sure that if you have already seen and tried these. Also apologies if all are not currently available... RIM takes their monte and descends at will as they revise things.

    I hope that something it is useful!

    See you soon!

  • BlackBerry Smartphones red LED does not

    My bright red LED message does not at all. How doi switch on? Please be specific to the topic where the icon or other path lie, thank you... (you wish that I did not leave the ATT store to talk to me in this unit!)

    The LED may blink for several reasons... the a main notification messages.

    To change a profile of notification on a BlackBerry smartphone using BlackBerry® Device Software 6.0, follow these steps:

    1. On the BlackBerry smartphone home screen, click profiles.
    2. In the notification profile list, click on change sounds and alerts.
    3. Click on sounds for the selected profile.
    4. Click on the application to change. Example: Messages Messages, calendar or level 1.
    5. Make the changes.
    6. Open the Menu and click Save.

    In step 4 above, click your messages and a corresponding email account, you will see the function of Visual alerts, the value IT for the red LED flashes when you receive a message.

  • BlackBerry Smartphones windows 7 does not recognize the device

    I was connected my 8330 for a desktop XP for a long time.  The sw of the device is v4.5.0.175.  I recently got a new Lenovo T410 laptop, running Windows 7.  I downloaded the software (version 5.0.1) DM and checked my camera SW is updated, but the laptop is still not recognize that the device is connected (via USB).  I tried all ports USB on the laptop and also followed all the steps detailed in KB13146, with no luck.  I find nothing in any of the forums that refer to Windows 7.  Can anyone help solve this problem?

    Hi and welcome to the Forums!

    Here is the list of troubleshooting atricles... I hope that something will be useful:

    http://supportforums.BlackBerry.com/T5/BlackBerry-Desktop-software/tips-for-getting-BlackBerry-deskt...
    KB02640 Troubleshooting USB connections
    KB15486 Top 10 smartphone BlackBerry and BlackBerry Desktop Manager troubleshooting tips
    KB11439 BlackBerry Desktop Software does not detect the BlackBerry smartphone when it is connected
    KB00019 PIN code not displayed in BlackBerry Desktop Redirector
    KB10938 "Current USB charge is insufficient," appears on the BlackBerry smartphone
    KB01451 How to enable Sync advanced logging if a wired synchronization fails
    KB19717 The BlackBerry smartphone is not detected as a USB mass storage device when connected to a computer

    In addition, make sure you use only the root USB ports... without hubs (sometimes the front-end ports are hubs... use a rear USB port). And don't forget to try to disable the USB power management in the configuration of your system (Device Manager).

    My apologies in advance if this is redundant - there is no way to be sure that if you have already seen and tried these. I can attest that DTM does not indeed a BB under Win7... mine is exactly so.

    I hope that something it is useful!

    See you soon!

  • Options for blackBerry Smartphones-General Options does not appear

    Help on the device says it should be a Menu Option called General Options.
    This does not appear on my device - there are many others but not this one
    Any ideas?

    Hi paulcusters,

    Click the green phone button, then click on the button to the left of the trackball and go to options.  There is a general opions here.  Try changing auto answer calls forever.

    See you soon!

  • BlackBerry Smartphones Internet + bbm does not

    Hello, I got a blackberry curve 8520.

    I had a BB bolt on my network O2 provider.

    I contacted them on this matter and they said everything was working fine.

    Thus, the only problem, there may be, it's something wrong with the phone.

    I heard the you must have something similar at the top of your screen or capital GPRS. On the other hand I have gprs in low case. is that what the problem is because I did all the service the customer with o2 said.

    I created a router host table. I also put at the service of data in the network for on settings, but nothing.

    I even restarted the phone and still nothing.

    I really, really need someone help on this. As I am very angry about what does not work as I paid for the bb bolt on and I don't get the service.

    Thank you

    NIC parmenter (parmazan16

    The parameters you need must be pushed to your phone by O2. I would suggest calling again - if they are sure that the BB add on has been activated and you phone through them they can increase in Blackberry for support

  • Bug in blackBerry Smartphones: 9790: Wikitude does not and can not be upgraded

    Bug: 9790: Wikitude does not and can not be upgraded

    Priority: Low (assuming that no one will use Wikitude now anyway)

    Severity: low

    Note: I understand that this is not an application of RIM, but it is an application preinstalled in BlackBerry Bold 9790, so please take care of this. I tried to document the issue as much as possible.

    I can not re - test, simply because I don't know how to install the old version. So, these are the steps that I went to join bugs:

    (1) have a 9790 Bold with the BlackBerry OS 7.0 as it was officially sold

    (2) Upgrade Bundle 2466 (7.0.0.609 Platform 9.16.0.77)

    (3) fully upgrade all official software from RIM AppWorld (Protect, Facebook, etc)

    (4) to set the phone to use location services

    (5) launching Wikitude

    YOU CAN SEE:

    Wikitude starts and appears the window ' Version is no longer supported. " Please update"and the OK" "button.

    6) click on the OK"" button.

    COMMENT: Wikitude closes and opens the browser with the URL:

    http://blackberrydl.Mobilizy.mobi/Wikitude.jad

    Two buttons appear: 'Download' and 'Cancel' and box "application Set permissions."

    (7) check them "Set application permissions" box (same end-test result is observed with this box unchecked)

    8) click on the Download"" button.

    You can observe: window: "Wikitude: Wikitude GmbH contains a module called Wikitude.» A module with this name already exists in the application "Wikitude". If you continue "Wikitude" will be replaced by Wikitude:Wikitude GmbH. proceed? »

    Buttons 'Yes' and 'No' appears.

    9) click on the Yes"" button.

    Observe: Download process begins, download file with a size of 4366 KB

    You can observe: after the success of downloading a new window appears with the message 'Error' and 'Ok' and 'Détails' buttons

    10) click on the button "Details".

    You can watch: new window with the message "Invalid COD" appears and buttons "OK" and "copy".

    11) click on the OK"" button.

    You can observe: the window is closed and "Wikitude" application is not installed.

    Thank you! Problem solved. Here's what I did:

    (1) Wikitude uninstalled

    (2) installed from AppWorld Wikitude

    Result: Wikitude runs successfully

    (clear the cache of the browser and try to download browser do not work)

  • BlackBerry smartphones get Images does not

    Hello, all. Until a few days ago everything worked properly. Now when I want to download the images in an email, nothing happens. It does not even show the download icon. And the possibility to get the Images went unless I have move to the text gross and back or leave the email and open again, but there is still nothing if I try to get pictures once again. Thanks for any help!

    Perform a simple reboot on the BlackBerry this way: with smart BlackBerry poweredphone, remove the battery for a minute and then reinsert the battery to restart. A reboot in this manner is prescribed for most defects and errors of operating system, and you will lose any data on the device doing so.

Maybe you are looking for

  • Error: "unable to release the video to external device" HD DVD playback

    Hi all this makes me crazy, I install only the updates mentioned on the site, but I get the following message appears when you try to play a HD DVD on the notbook or through my Tv. + Output of the external device video impossible. Please check the ex

  • ProBook 6540 b: no audio signal through Displayport

    The Displayport video output on 6540 b does support audio? If so, how I would allow sound through displayport through the windows? I was not able to get sound to participate in one of my TVs that has DisplayPort inputs.

  • Please recommend spy ware soft ware detection removal?

    I'm having trouble with spyware on my Imac. Looking for detection and removal software. Any suggestions? Any time I google I get a proliferation of the dracovenii. Thank you

  • Keyboard has its own life!

    I have a brand new T410i.     Running Windows 7.    I got it for a few days.   A couple of times already they keyboard has just gone 'crazy' on me.    I'll be typing away and then the cursor moves to the right, text will erase as I type it.  It happe

  • Scanner Epson Perfection 1200u and Windows 10

    I can't seem to download the drivers for this scanner, I have 10 windows, could this be the problem?