linked clones and their video card settings

Similar Questions

• SR2180NX adding memory and a video card, how?

  I finally decided to do a upgrade to my PC but I pushed my brain batty, trying to figure out how I would add memory and if I should update my video card now cause my Sims 2 game, instead of smooth running, it runs a little rough and frame by frame. Very annoying. I also want the Sims 3 to be able to run on my computer, I hope I can get it all done before they release.
  I have windows vista Home premium, and I have a PC I did not do anything for her, so it's a bit as if it was from the factory around a few programs of vanilla.
  
  * Manufacturer * Compaq Presario
  * Product * RK548AA-ABA SR2180NX
  Total number of logical CPUS * 2
  Total physical memory * 1.00 GB
  Total number of optical drives * 1
  Total number of disks hard * 1
  Total number of video cards * 1

  * Memory *.
  ------------------------------------------------------------------------------
  * System memory * total physical memory * 1.00 GB
  * Free physical memory * 443,21 MB
  Total virtual memory * 2.00 GB
  * Free up virtual memory * 1.94 GB
  * Page file space * 2.24 GB
  
  * 512 MB DDR2 - SDRAM (PC2-4200 / PC2-4300 / 533 MHz) * memory size * 512,00 MB
  * Type of memory * DDR2 SDRAM (PC2-4200 / PC2-4300 / 533 MHz)
  * Manufacturer of memory * Hyundai Electronics
  * Date of manufacture memory * week 39, year 2006
  * Revision memory code * 4141
  
  * 512 MB DDR2 - SDRAM (PC2-4200 / PC2-4300 / 533 MHz) * memory size * 512,00 MB
  * Type of memory * DDR2 SDRAM (PC2-4200 / PC2-4300 / 533 MHz)
  * Manufacturer of memory * Hyundai Electronics
  * Date of manufacture memory * week 39, year 2006
  * Revision memory code * 4141
  
  * Video card *.
  ------------------------------------------------------------------------------
  * Intel (R) 82945G Express Chipset Family * manufacturer * Intel Corporation
  * Video card chip Type * Intel (R) 82945G Express Chipset Family
  * Video card memory * 256,00 MB
  * Video card BIOS * Intel video BIOS
  *Driver*c:\windows\system32\drivers\igdkmd32.sys
  * Version * 7.14.10.1461, 25/03/2008
  ------------------------------------------------------------------------------
  and it's the plug to run the Sims 3
  ------------------------------------------------------------------------------
  THE SIMS 3 MINIMUM REQUIRED HARDWARE CONFIGURATION
  
  FOR WINDOWS VISTA
  * Windows Vista (Service Pack 1)
  * 2.4 GHz P4 or equivalent
  * 1.5 GB OF RAM
  * At least 6.5 GB of disk space hard at least 1 GB additional space happy Custom
  * 128 MB video card with support for Pixel Shader 2.0
  
  For computers using built-in graphics chipsets, the game requires at least:
  * Intel Integrated Chipset, GMA X 3000 or more.
  * 2.6 GHz Pentium D CPU, or 1.8 GHz Core 2 Duo or equivalent
  * 0.5 GB additional RAM
  
  SUPPORTED VIDEO CARDS
  NVIDIA GeForce series
  FX 5900, FX 5950
  6200, 6500, 6600, 6800,
  7200, 7300, 7600, 7800, 7900, 7950
  8400, 8500, 8600, 8800
  9600, 9800, GTX 260, GTX 280
  
  Series ATI Radeon™
  9500, 9600, 9800
  X 300, X 600, X 700, X 800, X 850
  X 1300, X 1600, X 1800, X 1900, X 1950
  2400, 2600, 2900
  3450, 3650, 3850, 3870,
  4850, 4870
  
  Intel® Extreme Graphics
  GMA X 3 x 00 series
  Laptop versions of these chipsets may work, but can run relatively slower. Autonomous cards installed in vanilla (not PCIe or PCIx or AGP) PCI slots, such as some GeForce FX variants, will perform badly. Intel chipsets integrated starring parts underclockes would not run properly.
  
  Chipsets integrated such as the ATI Xpress and the NVIDIA TurboCache variants will have low settings selected, but should operate satisfactorily.
  
  Please note that attempting to play the game using video hardware that is not listed above may result in reduced performance, graphical issues or make the game work do not at all.
  The NVIDIA GeForce FX series is unsupported under Vista.
  
  and he also said when I watched the news of the memory of the BIOS screen:
  
  Installed memory 1024 MB/PC2-4200
  Bank 1 512 MB/DDR2 SDRAM memory
  Memory Bank 2 not installed
  Memory bench 3 512 MB/DDR2 SDRAM
  Memory bench 4 not installed

  I know that I have to add memory and a video card, or even a power supply according to the video card, I get. Memory seems simple and easy to do, but the power SUPPLY and the video card, makes me a little nervous, any suggestions on what I should get and instructions on how to proceed will be greatly appreciated Thx! I apologize for this post being so long.

  Message edited by CareBear31 on 02/05/2009 13:02

  Adding instructions are here. When you buy new memory be sure and go to the website of the manufacturer of the memory. Use only brands so that they ensure th your product compatibility. Use the memory Configurator tools on the website of the manufacturer of the memory. Here are a few major brands for you: Kingston, Crucial, Corsair:

  Change the power supply: This video on youtube is pretty decent for generic power supply switching.

  Thislinkhas information on opening the cover and remove the cover.

  When you select a video card do not get cards great physically (i.e. ATI HD 4870 / 4850) because they are double wide and does not have limited space. Fantastic cards but are not for the pre-built PC.

  Any ATX PSU fits your case. 450 watts or therabouts enough for almost any addition of hardware on your pc. Do yourself a favor and stick the best brands such as Corsair, OCZ and others. Generic brands are not worth the problems they can bring even if they are cheaper.

• U2415, a VGA and DVI video card?

  Hello

  We recently bought 4 u2415 dell screens for our company's graphic design team, I am a manger IT to my company, but the screen was not given by me and we encountered a problem linking them. The video card has only 1 single VGA port and a DVI port and because of this, I bought several adapters and cables to try to connect these monitors but I still can't get no signal, please help, I'm a little before I sent monitors to the advertiser. For VGA, I bought an active adapter convert it that HDMI port, I connect via dp to hdmi cable and get still no signal. For DVI, I bought a dp cable dvi and im still getting no signal. Please tell me what is wrong and if have a little chance to connect these monitors today before im refer to them.

  The cables you bought are designed to go to DP to HDMI or DVI monitor video card. You can't go back.

  The U2415 of the maximum resolution is 1920 x 1200 60Hz.So forget using the U2415 DP or CDM. The cheapest solution is this =
  Computer video card DVI out-->--> U2415 HDMI DVI to HDMI Cable to

• Why pes 2012 does not work with me and my video card is 1699 MB Intel HD Graphics(core i3)?

  Why pes 2012 does not work with me and my video card is 1699 MB Intel HD Graphics(core i3)?

  Hello

  You receive an error message?
  
  Method 1:
  You can update the drivers of graphics cards and check.
  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  
  Method 2:
  You can also perform a clean boot and check if it works:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: after a repair, be sure to set the computer to start as usual as mentioned in step 7 in the Knowledge Base article

  You can also check out the link:
  The problems of the game performance
  http://Windows.Microsoft.com/en-us/Windows7/fixing-game-performance-problems
  Diagnose problems running DirectX
  http://Windows.Microsoft.com/en-us/Windows7/diagnosing-basic-problems-with-DirectX

• List virtual machines and their DNS server settings

  I try to list virtual machines and their primary and secondary DNS server addresses.  Are the cmdlets in vmware that can do this, or would I need to use the invoke-script command.  I have the list of virtual machines and I want to list them all with their DNS server addresses.

  I tried to use the wmi objects such as:

  Win32_networkadapterconfiguration get-wmiobject - computername "servername |

  Select name, DNSServerSearchOrder

  It would give me the specific server name and addresses of dns.

  But I need the list of servernames which I would like to list some and their

  DNSserversearchorder settings (DNS settings)

  I tried to put the servernames list in a text file using

  Get - vm | Export-csv C:\computername.txt - notype

  Then I used the get-content command and the pipe in the get-wmiobject

  command like below:

  $servers = get-Content c:\computername.txt

  ForEach ($server in $servers)

  {get-wmiobject Win32_networkadapterconfiguration - computername $server

  | where {$_.} IPEnabled-fits 'True'} | Select-object

  name, DNSServerSearchOrder

  But when I run this command fails with errors such as a pipe empty

  element is not allowed.  I don't know if the above script has all synatx

  error or what is the best way to get a list of servers and their dns server

  Parameters.

  I know the wmiobject maybe out of this range in these newsgroups but there at - it a script in powershell, vmware or windows powershell to get a list of servername (which are mostly VMS) and their DNS server settings.

  Try the following script to get the DNS search order:

  Get-Content c:\computername.txt | `
  ForEach-Object {
    Get-WMIObject Win32_NetworkAdapterConfiguration -Computername $_ | `
      Where-Object {$_.IPEnabled -match "True"} | `
      Select-Object -property DNSHostName,DNSServerSearchOrder
  }
  

  Best regards, Robert

• A55 and PCIe video card installation

  Work with a 8705-DHU and try to install a video card into the PCIe slot to allow the use of two monitors.  The idea is to attach a monitor to the on-board and the new card for a second monitor, and then expand office.  I got the second card installed (PN 73P 2516) and see the family of chipsets Intel 946GZ Express, no other video card.  I expect to see two graphics cards in Device Manager, but see only one.  Both monitors work, but I can't extend the desktop, only clone.  Display Properties Windows sees only a graphics card and therefore only a single monitor.  Intel graphics options see 2 monitors, but allows only for monitors must be cloned.  I can't imagine what I'm doing wrong, I worked on the PC for a long time.  There are a number of FRU, (39J9334) on the map, but I am at a loss.  I'll update the BIOS tomorrow when I return to the system, but I'm looking for other ideas.  I used the drivers supplied with the card, found an update, but once installed the cloning stop working.  I couldn't find anything in the BIOS, so I am at a loss.  Any ideas/suggestions would be appreciated.

  Other research showing the card only supports clone mode on this particular system... too bad, I have not found this link before posting.

  http://www-307.IBM.com/PC/support/site.WSS/document.do?sitestyle=Lenovo&lndocid=MIGR-60292

• Problem with the floating linked clones and Persona

  Hello

  We run a build view Horizon 6.2.0 - 3005368.

  Just improved our VMware environment to 6.2 and installing an APEX 2800 PCoIP card on our guests.

  I had a pool of office dedicated clone bound for users.

  Now, I made a new image of master and made a new Automated Desktop Pool pool who are floating clone related.

  With the dedicated bound vmis, we place disc profiles of users etc are located.

  With the new pool, I'll use Persona. I followed this guide - http://terenceluk.blogspot.no/2012/10/configuring-roaming-profiles-with.html?showComment=1445933020356 and it works very well indeed, almost.

  For users of a trial, I can see that if something I save it to the desktop, it will be saved on the server of file \\fileserver\redirected$\%username%\Desktop

  When I use my user and try to even something on the desktop - it c:\%username%\Desktop

  I tried to reset, remove my user etc., but it's not. All the settings I made in the GPO - Computer Configuration-> administration-> classic administrative templates (ADM) models-> Configuration of the VMware View Agent-> Persona

  Management-> Folder Redirection

  But my users settings are only "local".

  How is it?

  This can be caused by an incorrect action or NTFS permissions on the redirection of folder/persona.

  She is also due if your user account has a profile on the parent whose linked clone desktops are created.

• Unable to play Minecraft and driver video card error message

  Recently I bought Minecraft, but the game won't load due to the following error:
  Bad video card drivers!
  -----------------------

  Minecraft could not start because it did not find an accelerated OpenGL mode. Generally, this can be corrected by updating the video card drivers.

  BEGIN 7fe0271 error REPORT
  Generated 08/11/11 15:20
  Minecraft: Minecraft Beta 1.7.3
  OS: Windows 7 (x 86) version 6.1
  Java: 1.6.0_26, Sun Microsystems Inc.
  VM: Java hotspot Client VM (mixed mode), Sun Microsystems Inc.
  LWJGL: 2.4.2
  [unable to get system (java.lang.NullPointerException) properties]
  org.lwjgl.LWJGLException: Pixel format not accelerated
  t org.lwjgl.opengl.WindowsPeerInfo.nChoosePixelForma (Native Method)
  at org.lwjgl.opengl.WindowsPeerInfo.choosePixelFormat (WindowsPeerInfo.java:52)
  at org.lwjgl.opengl.WindowsDisplay.createWindow (Windows wsDisplay.java:185)
  at org.lwjgl.opengl.Display.createWindow (Display.java:311)
  at org.lwjgl.opengl.Display.create(Display.java:856)
  at org.lwjgl.opengl.Display.create(Display.java:784)
  at org.lwjgl.opengl.Display.create(Display.java:765)
  at net.minecraft.client.Minecraft.a(SourceFile:294)
  at net.minecraft.client.Minecraft.run(SourceFile:716)
  at java.lang.Thread.run (unknown Source)
  ERROR a77717d2 END REPORT

  I looked online and the reason is that my graphics driver is not up-to-date, however, because use custom drivers Toshiba I can't go to the website of intel and get the newest, I know that my only current is obsolete, but there are no new drivers on the Toshiba site. Help, please!

  Hi OzzyAmir,

  Can you post what model of laptop, you have, please?

  Usually not speaking, there s no problem to install other display drivers, but it happens on your own risk because the drivers are not pre-tested by Toshiba.

  Intel drivers, you can install through the Device Manager > update drivers if you click on the graphics card. Then, choose the Advanced installation and choose the directory of the driver.

• Changing the video card settings.

  I changed the settings on my video card for something that that does not support my monitor/TV. Now I don't get a picture, just a blue screen saying "NOT SUPPORTED". How can I change the return parameters?

  No problem.

• I spilled liquid on my G6 Pavilion and the video card no longer works

  HP Pavilion G6 series number 868R4-FV6RQ-BHRP9-BJCP9-BY2TY

  Running windows 7.

  A cat knocked over a cup spill liquid on the computer. He connected, blue return projected and restarted itself. Aside from the message that it is a Code of 43 for the video card driver, things seem to work.

  What can we do?

  Turn it off! Unplug the power cord!  Remove the battery!

  Partially disassemble the laptop and let it dry for 5 days in an air-conditioned room, back to gether and hope that there is no permanent damage.

• p6216it and new video card

  Hi all

  I just buyed a desktop Pavilion p6216it and im intend to change video card PC. One that comes with the computer is an ATI HD4350 with 512 MB dedicated. I would replace this card with an Nvidia gtx260 896 MB (who need extra power).

  The power supply (PSU) that comes with the PC is a power of 300W and isn't any 6-pin Molex or PCI - X, but only 2 SATA power-free location.

  Now, I think I have 2 choices:

  (1) keep my power supply 300W for the gtx260 and buy an adapter to convert sata pci - x power (but perhaps 300W is not enough)

  (2) buy a new power supply (450W would be nice I think)

  What should I do?

  Thanks in advance and sorry for my English

  Treuz

  If you need extra power never so it wouldn't really be 'better' unless you can get one of the same quality for about the same price (or less) than the supply of 450W. Go to an increase in the power supply would ensure that you have enough power, if you add accessories or cards in the future however.

• Food and update video card for Pavilion s5 - 1021p

  I want to upgrade the power supply 270w in my Pavilion s5 - to 500-600w 1021p and replace the graphics card integrated with a Radeon 4650 video card.  Is it possible, given the constraints of size?  Any help is appreciated!

  Hi callen3625,

  According to HP Partsufer, the power supply of your PC is not included because it has a separate part number.  This is also confirmed by the information contained in the library of Services HP partner.  The block of power SUPPLY HP Partsurfer therein is 220 watts.

  Look here in HP Partsurfer for video cards that are used in the new Slimline models with a 220 Watt power supply.  These cards have been made specifically for the HP Slimline PC with a 220 watt power supply.

  Even more recent slimlines are other graphics cards AMD that work with a 220 Watt power supply.  Look here and here.

  Review the specifications of performance ATI and NVIDIA . Look at the specifications of strip memory bandwidth and level of DirectX support.

  You should contact HP support and get a recommendation of the video card or maybe even HP Partsurfer.

• Linked Clones and snapshots - which can be removed and when?

  Hello

  Sorry if this is a stupid question. I'm new to the linked clones.

  I was able to create clones related win2k8r2 invited.  Everything seems to work ok.  However, once a linked clone is created, is it still necessary to keep the parent snapshot?  That is to say, snapshot of the parent is necessary after related cloning?

  My env:

  VMware ESXi 4.1.0 build-433742

  VMware vSphere PowerCLI 4.1 build 332441 U1

  Thank you

  T

  It must be remembered that a clone is based on the parent machine and a snapshot that you see in the server view.  Multiple snapshots can be consolidated or "rolled up", but depends on the clone.  The parent can put off when the do not need to save on resources in your environment, because that's what the replica is for.  I do not agree with Andre and suggest that you keep the snapshot that you clones are configured to use, with the exception on the consolidation of old clichés.

• View 5 POC, Windows 7 Enterprise, linked Clones and VMXNET3

  I spin a CEP for Views5 and experiencing major issues with the VMXNET3 device when configuring desktop using linked Clones. About half of the configured computers have errors NIC with the fact that he is unable to see the network.

  Has anyone else had similar problems?

  Apply the fix mentioned in: http://pubs.vmware.com/view-50/topic/com.vmware.ICbase/PDF/view-50-administration.pdf

  This will fix the problem as it did for me.

  Read also: http://www.vmware.com/files/pdf/VMware-View-OptimizationGuideWindows7-EN.pdf

• Linked Clones and SCSI controller

  I created an automated linked clone pool that points to a virtual machine Windows XP parent. I used the parallel LSI Logic Controller and the value of the SCSI disk (0:0). The problem is, after the pool is created, when the user connects, they invited to a username and password with this message "you must be member of the Administrators group on this computer to install this equipment. SCSI controller.

  I don't do our domain users members of the local Administrators group, so this creates a big problem.

  Any suggestions?

  Thank you

  Mike

  Please perform following steps.

  -----------------------------------------

  • Create a new virtual machine with custom SCSI controller. (Keep floppy drive configuration)
  • Extract the downloaded driver symmpi_wXP_1201800.zip (version 1.28.03)
  • The driver disk image can be by editing the VM, floppy.
  • Start the installation of Windows XP, press F6 when request and then point to the driver on the floppy drive
  • Continue and finish the installation.
  • Now to use this virtual machine as a VM parent, and it should solve your problem