Linksys connect to Vista

Similar Questions

• Error R6025 Runtime after connect you Vista - card Flash memory does not

  Hello
  I am a newbie & would appreciate any advice.

  I get a runtime R6025 error message when I connect Windows Vista.
  When I click out of the box, then I get a message saying Toshiba Flash Cards not working do not.

  I cancel that and my laptop is ok except that I don't know if the flashcard works or not because I don't know what he does.

  Sorry if I seem thick

  Thank you

  Neelie

  Hello Neelie

  Without much explanation here, in my opinion, you can try to resolve this problem if you remove the package of added value of the system (Control Panel > programs and features), restart your computer and install the latest version available on the Toshiba support page.

  You can find it under http://eu.computers.toshiba-europe.com > support & downloads.

• How do the PPPOE connection automatic connection on Vista

  Hello!

  I have the internet connection for PPPOE. It works fine, but I want to autoconnect when I start my PC.
  I tried to create a network connections shortcut and copy it to all the programs/startup.
  It did not work.

  Thank you!

  OK, try this. Open the Control Panel and select Internet Options > connections . Make sure your PPPoE connection is highlighted and always set the default connection is checked. This assumes that your PPPoE connection is your default value.

  See also the answer to a similar question for quite awhile in time...

  http://Forum.Soft32.com/Windows/auto-connection-Windows-Vista-log-ftopict376533.html

  Good luck... MS - MVP Windows Desktop Experience, "when everything has failed, read the operating instructions.

• Re-installing Linksys Connect on mobile after the new hard drive installed

  I have a router E4200 and had loaded on my laptop Connect. My hard drive crashed and needs replacement. I have had no problem signing on my WiFi once I got the new installed hard drive.

  With the new hard drive, I now do not have Linksys Connect installed on my laptop. My question is: can I re - install connection with the router works perfectly good or re-setup Connect with the router already up and running will cause me problems?

  Thanks for any help.

  Here is an article on the configuration of the software once the router has already been put in place.

  http://KB.Linksys.com/Linksys/UKP.aspx?pid=80&app=VW&VW=1&login=1&JSON=1&docid=90fabd0b3674497489d42...

• Connect home Vista & Windows XP Media to the network... Help!

  What are the steps? I keep getting blocked and the message says to contact administrators, but it's us! What I am doing wrong?

  See the following thread that offers some good advice on how to set up:http://forums.techguy.org/networking/545552-how-do-i-network-my.html.

  Here is a generic Microsoft article on how to set up a home network: http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-home-network.

  Here is another article on the connection of Vista and XP together: http://www.informit.com/articles/article.aspx?p=1165037.

  Here's a last article on how to set up a network that covers the XP and Vista together among other options:http://www.practicallynetworked.com/sharing/vista/Vista_network_options.shtml.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Can not connect to Vista - connection failed user profile Service

  System message: user profile Service service has no connection

  User profile cannot be loaded.

  Help, please!

  Thank you very much

  Foam HB

  original message: can not connect to Vista

  ·                        Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:

  ·                        http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  See if the information in the above tutorial will help you.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Difficulty of a corrupted user profile

  After creating the profile, you can copy the files from the existing profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  See you soon.

  Mick Murphy - Microsoft partner

• How to bypass the automatic connection in Vista. The SHIFT key after that logging does not work.

  I'll put up a laboratory of small kiosk for my students with a minimum account privs.  Sometimes I need to login with the administrator account to perform regular maintenance or solve a problem.  in xp, all I had to do was hold down the SHIFT key before the blue startup screen and all accounts (including my admin account) were visible.  This doesn't seem to work with vista.  is there a secret combo of keyboard shortcuts?  What should I do to ensure that both accounts visible?

  Hi Scentfromabove,

  Follow this step in order to bypass the automatic connection in vista.

  1. Click Start and type netplwiz in the start search box and press ENTER.
  2. check the users must enter a user name and password to use this computer
  3. click on apply and OK.

  I hope this helps.

  Bindu S - Microsoft Support
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Hi, I have a camcorder Sony TRV 356 I am unable to connect on vista or windows 7 via USB

  Hi, I have a camcorder Sony TRV 356 I am unable to connect on vista or windows 7 via USB

  Hello Sajid,

  The community here is about the countries United States, Canada and Asia-Pacific. Your DCR-TRV356E model is a model British camcorder.

  However, to answer your question,.

  The DCR-TRV356E USB streaming function is not compatible with the operating system Windows Vista and Windows 7. You can connect the camcorder to the computer using the A / V cable connection or using an i.Link cable.

  You can visit the European Forums of suggestions regarding the transfer of videos to Windows Vista or Windows 7 computer.

  http://www.Sony.co.UK/discussions/community/en/support/cameras_and_camcorders

  If my post answered your question, please mark it as an "accepted Solution".

  Thank you for your message.

• Linksys connection shows poor all the time

  When I check my status on my connection why you say poor all the time? I also noticed that there are others that are related to my linkskys and my connection is always ' say poor. How can I get a better connection? Thank you

  Hello

  You really need to be checked in the forums for your version of Windows.

  Answers - Windows Forums
  http://answers.Microsoft.com/en-us/Windows

  ---------------------------------------

  It is more connected to your router that are not in your household? If so, you will need to
  reset the router security. All unauthorized connections are the security risks and also use
  your connection resource. Check with the manufacturer of the router.

  Distance and other interference can affect the quality of the connection. Also check updates
  your WiFi and NIC drivers.

  LinkSys has support and excellent help. Also check the LinkSys forums.

  LinkSys support
  http://homesupport.Cisco.com/en-us/Wireless/Linksys

  LinkSys forums
  http://homecommunity.Cisco.com/community/?category.ID=Linksys

  ==================================================================

  References to Vista also apply to Windows 7.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ====================================================

  After that the foregoing: (here, the NETWORK card and Wifi are interchangeable in the sense that the two must be
  fact that you can do if you first use).

  Follow these steps:

  Control Panel - network - write down of the brand and the model of the Wifi - double click - top
  tab of the driver - write version - click on update driver (can't do anything like MS
  is far behind the pilots of certification). Then right click on the Wifi/NIC device and UNINSTALL
  -Reboot - it will refresh the driver stack.

  If necessary to download drivers on another machine and transfer on the problem computer via
  removable media such as a USB key or CD - DVD.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods
  below is preferred so that the latest drivers from the manufacturer of system and device manufacturers are
  found)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version.
  (Those become your fonts of rescue system manufacturer).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as windows
  7 love the updated drivers.

  ======================================

  If necessary:

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet in Vista (and Windows 7)
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

• Unable to connect to Vista Home Premium DMA2200

  I recently had the need to re - install my HTPC (Vista Home Premium). When I went to set up my DMA2200, it gets to the point in VMC, where there a checkbox in 'Setting media locations', and he is reportedly trying to connect to the DMA2200 ("connecting to Extender").

  At this point, it takes much more long as it should and VMC possibly errors with the message "Extender didn't connect." On the DMA2200, I see "Login failed."

  Looking at the Log on the HTPC case, I see five entries in the Media Center newspaper during the time that I was trying to match my DMA2200 + HTPC (oldest to newest):

  1. HTPC beginning of the installation of Windows Media Center Extender with the following options: Firewall (0,0,1,1) Power management (0) media settings (1)

  2. The installer of Windows Media Center Extender configured successfully, the Windows Media Center PC for use with an Extender.

  3. Windows Media Center Extender DMA2200us (sditz5ep3yi0) 'uuid:689C2DE0-4282-48BA-BF44-9C56E2176767' found at the address 192.168.1.135.

  4. Windows Media Center Extender Setup has exchanged certificates with device 'uuid:689C2DE0-4282-48BA-BF44-9C56E2176767'.

  5. Windows Media Center Extender account Mcx1 was created for device 'uuid:689C2DE0-4282-48BA-BF44-9C56E2176767'.

  As far as I know, everything looks great. In addition, I am able to desktop remotely for my HTPC and ping my DMA2200. I have not either a complicated network. Just my HTPC, a Linksys router base with the default configuration and the DMA2200. I have the firewall running on my HTPC, but I allowed the Extender pass. I also tried to stop the firewall, but it did not help. I reinstalled Vista and reset the DMA2200 to default settings. Same question.

  The only thing at this point that I can think of who can help is when I got my DMA2200, I remember that it came with an installation disk (someone check?) and I used it. I am no longer able to find such a disc, nor I see any kind of tools package available for download.

  Does anyone have any ideas where I should go next? I'm almost ready to return this as a defective unit.

  This eventually be due to a change in registry/dll to enable RDP on Home Premium. I forgot it was on an image I found a new installation. After having finally dig my Vista disk and reinstall the old fashioned way w / nothing else Vista & drivers, the problem has been resolved and has not recurred.

• Configure the router linksys on windows vista

  Recently I bought a linksys wireless router and have problems when configuring it on windows vista home.

  I have read many articles that while configuration that I need to connect the DSL modem (DSL in my case) to the router (WAN port) and also a thread more (that came with the router) to the laptop. If I connect my laptop with router then how is the wireless network or if it is required to do the installation?
  Do I need a PC/laptop always connected with wireless router and then only I can take advantage of being wireless (I hope not)? When can I disconnect the cable between the router and the laptop and use internet as well?

  The reason for asking this question, is that my laptop LAN port is not functional. If I use any other laptop for the initial setup and then use my laptop to connect to the router if it works without using b & w computer laptop and router connection?

  I'm really a beginner for this please help.

  Thank you

  Hi, thanks for your answers.

  I had a temporary cell phone to set up my wireless router. The question I m is that I can access internet from my lan from the dsl model cable but I can't access the internet when I connect the LAN to my wireless router and a join cable wireless router to my laptop.

  While the configuration of the wireless router from the cd that I got with router reached the last step to find the internet connection and then pop up msg this router is not able to find the internet connection. What should I do?

  I just saw a thread (http://forums.linksysbycisco.com/linksys/board/message?board.id=Wireless_Routers&thread.id=58742&view=by_date_ascending&page=2) and cloned my mac but coldnt able address to make it work.

  I'll post my ipconfig details in a moment.

  C:\Users\Chakrapani V>ipconfig /all
  
  Windows IP Configuration
  
     Host Name . . . . . . . . . . . . : ChakrapaniV   Primary Dns Suffix  . . . . . . . :   Node Type . . . . . . . . . . . . : Hybrid   IP Routing Enabled. . . . . . . . : No   WINS Proxy Enabled. . . . . . . . : No
  
  Ethernet adapter Local Area Connection:
  
     Connection-specific DNS Suffix  . :   Description . . . . . . . . . . . : Marvell Yukon 88E8040 PCI-E Fast Ethernet Controller   Physical Address. . . . . . . . . : 00-21-9B-F1-26-C4   DHCP Enabled. . . . . . . . . . . : Yes   Autoconfiguration Enabled . . . . : Yes   Link-local IPv6 Address . . . . . : fe80::71d3:2386:391a:3d9a%11(Preferred)   IPv4 Address. . . . . . . . . . . : 192.168.1.100(Preferred)   Subnet Mask . . . . . . . . . . . : 255.255.255.0   Lease Obtained. . . . . . . . . . : 22 October 2009 07:24:15   Lease Expires . . . . . . . . . . : 23 October 2009 07:24:15   Default Gateway . . . . . . . . . : 192.168.1.1   DHCP Server . . . . . . . . . . . : 192.168.1.1   DNS Servers . . . . . . . . . . . : 192.168.1.1   NetBIOS over Tcpip. . . . . . . . : Enabled
  
  Tunnel adapter Local Area Connection* 6:
  
     Media State . . . . . . . . . . . : Media disconnected   Connection-specific DNS Suffix  . :   Description . . . . . . . . . . . : isatap.{314241DB-C984-4A60-A127-7D9246A8A709}   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0   DHCP Enabled. . . . . . . . . . . : No   Autoconfiguration Enabled . . . . : Yes
  
  Tunnel adapter Local Area Connection* 7:
  
     Media State . . . . . . . . . . . : Media disconnected   Connection-specific DNS Suffix  . :   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface   Physical Address. . . . . . . . . : 02-00-54-55-4E-01   DHCP Enabled. . . . . . . . . . . : No   Autoconfiguration Enabled . . . . : Yes
  
  Tunnel adapter Local Area Connection* 17:
  
     Media State . . . . . . . . . . . : Media disconnected   Connection-specific DNS Suffix  . :   Description . . . . . . . . . . . : isatap.{A1DE9DAE-229D-4929-A91E-F208BB0DCA22}   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0   DHCP Enabled. . . . . . . . . . . : No   Autoconfiguration Enabled . . . . : Yes
  

• Satellite A100-906: slow internet connection with Vista

  Hello world...

  I installed vista ultimate and I must say it's great... the problem is that the connection to the network is so slow... on xp, I used to get speeds up to 4.5 kb on my connection dial-up... on vista, I almost reach 1.5 KB... can someone tell me what is the problem and how can I solve this problem...

  Maybe your TCP settings are not correct? Try searching on google for some tools that configure your tcp and internet settings correctly, then maybe you can solve it this way.
  BTW, I Don t think this is a related thing of material...

  Welcome them

  P.S.: Reinstall the drivers sometimes helps...

• Satellite P100-434: wireless connection with Vista problem

  Just bought this laptop with Vista and so far could not get the wireless to connect, I have 3 other computers and they will all connect, I have reset the router and set up new accounts on other computers without problem, but unable to do it on the P100.

  I tried the new RADAR feature and will not pick up all the networks, but by trying to establish a new connection it shows that a wireless network is available but it is nameless, although my network is named, I took the passkey of the network so that it is open but still does not connect, LAN via ethernet fine work.

  Wireless switch is on, but when I drag off switching wireless says WE

  Hello

  I can't give you an exactly the answer why you cannot connect to your WLan with Vista because there are so many options that should be checked.
  But I think that you will find the solution yourself with a little help from the Microsoft Web site.

  Please see this site:
  Connect to a network with Windows Vista wireless
  http://www.Microsoft.com/technet/community/columns/cableguy/cg0406.mspx

  You will find many useful tips, screenshots and Tips how to connect to WiFi with Vista.

  Please post again if you have found the key

• Stature I9: connecting to vista?

  I have an i9 and windows vista is something that will work for me connect my phone to my computer, I have a phone that offers all of these features and I can't use it for photos, music or whatever it is can any body help?

  Cannot connect to XP on my i9 with the exception of the memory card. Boostmobile does not support what I understand.

• XP Remote Desktop can only connect to Vista once by restarting: error 0xc00002fd

  I am running XP SP3 and by connecting to a computer running Windows Vista by using RDP 6.1 (also tried 7.0) with NLA.  I did the configuration of the registry for SINGLE sign-on (although it reproduced without these registry entries with new credentials).  The first logon works perfectly.  That I disconnect the Vista machine.  Then the second connection comes with "an authentication error has occurred (0xc00002fd)."  I can never get another connection to work.  I reboot XP and it works again, once.  The error seems to be a sort of encryption problem.  If CredSSP is cached something that does not work?  Any help is greatly appreciated!

  Hi Brändli,

  • Is Windows Vista computer on a domain network?

  This error may occur sometimes if Credential Security Support Provider (CredSSP) is not correctly enabled. You can access the link below and follow the steps described in the article turn on CredSSP.

  http://support.Microsoft.com/kb/951608/en-us?p=1

  If the problem persists after you follow the steps described in the article above, you can access the link below and post your question in the theTechNet community, which will provide the support you want.

  http://social.technet.Microsoft.com/forums/en/VirtualMachineManager/threads

  I hope this helps. Let us know the result.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.