Linksys WRT54g + WAP54g setup help

Similar Questions

• Linksys WRT54GS Help - Bricked itself?

  Hello community,

  I recently inherited a router Linksys WRT54GS my boyfriend hasn't needed. I kept it in storage for about 6 months because I didn't really need, but yesterday, I found that lying around and decided to go ahead and plug it in, to see if I could use it as a switch to connect my computer, Xbox and PS3. So I plug it into the wall... And it seems dead. All of the lights on the front panel are turned off. On a whim, I decided to plug it into my computer, wired and test pings. I kept getting the "Network unreachable" error, and the router was not network. However, the light on the front corresponding to the numbers 1-4 port back lit up when I plugged my computer at each port. There is no reset anything else, even after a 30-30-30. Should what steps I take now?

  It is possible that the router no longer works. Have you tried to use the router when your friend gave you? If you are still not able to ping the router using its IP address standard, try setting static IP on your computer using 192.168.1.50 for the IP address and 192.168.1.1 for the default gateway. Once the IP static value, try to ping the router command and access the router page using 192.168.1.1.

• Guest WIFI Linksys WRT54GS by connecting (v6) to ActionTec (verizon fios)...

  Hello

  I want to activate access wifi comments so that I do not share my wifi password main with the guests to allow them to access the Internet (for browsing mainly).

  I currently have Verizon FIOS as my ISP and use ActionTec (MI424WR Rev I). Unforunately, due to certain levels of firmware, allowing access as guest (via dual SSID) is not possible.

  I have an old router d LinkSys WRT54GS (v6) and I was wondering if I can use to connect to my rounter Verizon ActionTec providing guest network? I want to keep Verizon FIOS ActionTec as my main router that I have other devices connected and configured for it.

  So, I was wondering how to connect WRT54GS (v6) to my Verizon ActionTec rounter to leave wifi access without me offering me the passwd wifi main comments?

  My WRT54GS (v6) does NOT run any DD - WRT or OpenWRT f/w but it is running original LinkSys f/w (1.52.8).

  I want to know the following:

  (1) do I need to connect the LAN of router LinkSys LAN Port of Verizon ActionTec port? Or can I connect to LAN_port of Verizon ActionTec WAN_port of LinkSys?

  (2) do I need to disable the DHCP server on LinkSys?

  (3) can I create an additional SSID (with friendly passwd) on LinkSys for allow comments access this SSID while I access my original SSID of ActionTec?

  I went thru' http://www.linksys.com/us/support-article?articleNum=132275 and I tried, but my devices were not able to access internet when connecting to guest SSID.

  Thus, you can enjoy a few tips here. Thank you!

  Kind regards

  Diakité.

  Hi kamdard. You can actually set up the WRT54GS as a wireless network completely different from the one you are currently configuring it with a different name and a different password. If you want the host computers or wireless devices behind the WRT54GS to be able to communicate with the computers behind the ActionTec router then you can follow the method from LAN to LAN. If this isn't the case, then follow the LAN WAN configuraiton.

  Only, you will need to disable DHCP on the ActionTec if you follow the method from LAN to LAN.

  For easy setup, I have personally, suggest that you follow the LAN WAN config. This means that you connect the Ethernet cable between the LAN of your Action Tec port WAN or the Linksys router's Internet port. In this way, you don't have to disable DHCP in the WRT54GS and to access its configuration page via 192.168.1.1 anytime.

  Furthermore, what is the IP address of your router, ActionTec? If it is on 192.168.1.1, too, you may need to change the local IP address of the router Linksys 192.168.2.1. Once done, access the configuration of the WRT54GS page and customize the wireless network and the wireless password.

  Also, before all configurations, it's better reset the unit to default settings. It is done by pressing the reset button at the back of the routerfor 30 seconds while the power is on. Release the button and unplug the unit.

  Hope the above helps.

• How LinkSys WRT54G v7 supports RTSP streaming service?

  Hello

  I use the LinkSys WRT54G v7 and I can see the RTSP videos using VLC player to m.youtube.com. Strangely, I can't play videos if another AP as the DLINK is used instead of LinkSys.

  I analyzed packages and discovered that RTSP server (youtube) sends RTP packets to the ports of the client which are acquired to the RTSP SETUP procedures. Then the Server packets cannot reach the customer because the hole of the UDP is not perforated to the AP.

  But, when I use the LinkSys, RTP packets can cross the NAT.

  That is my question. LinkSys offers NAT traversal for RTSP streaming service? So, why can't find a list of features on this subject from the LinkSys product information? No explanation for this?

  Thank you in advance for your help!

  1. None of the NAT helpers in the Linksys firmware are documented anywhere.

  2. If possible, they added a helper for RTP.

  3. it could also be that VLC player in front of the port with UPnP.

• Linksys WRT54G broadcasts simultaneously two wireless signals.

  Everyone knows the Linksys WRT54G Router broadcast two signals?  I did a wirelss security reset in my modem the other day and changed the name of the SSID broadcast.  Now I have the old and the new SSID broadcast at the sametime.  When I go into my router I see that a new figure.  My problem is that the new SSID I created is encrypted with WPA Personal and older SSID broadcasting still is not encrypted, anyone can jump on the signal.  The older SSID has been initially encrypted in WEP... I can't understand this.  Can anyone help?

  FYI... the new SSID signal is very strong and the most original is weak.

  I turned on MAC filtering wireless in order to prevent anyone with a laptop that is close to my network.

  Your router can broadcast only one SSID. If you have changed and configure WPA Personal then that's for sure.

  The unsecured "linksys" network is your neighbor. If you check the web interface of the unsecured "linksys" network you will see that it is another. See the status page.

• Assistance using Windows using Linksys WRT54G wireless remote

  Please someone help me. I have Qwest DSL service, ActionTec Gt701R and Linksys WRT54G - Version 6.

  If I connect directly to the Modem, send a request for Assistance from a distance, the Expert can connect to me without any problems. Here is the IP ticket RA information-

  RCTICKET = "65538,1,71.215.174.28:38861;192.168.0.2:3389; trippc:3389, *.

  When I'm connected wireless using the WRT54G, send a request for Assistance from a distance, the Expert cannot connect to me with an error that the DNS cannot resolve the host name. I assigned a static IP address to my laptop and the Port 3389 to sent to this IP address, according to the Linksys support. She is the information the RA ticket IP for failure.

  RCTICKET = "65538,1,192.168.0.4:1293;10.10.10.50:3389; trippc:3389, *.

  The IP address in this post are internal addresses, the Expert cannot find them on the Internet.

  Anyone have this working? If you have, please send the instructions step by step that followed you.

  Thanks in advance for your help.

  Problem solved on the Forum of Qwest. The modem must be changed to use "a transparent bridging. The the WRT54G must be changed from automatic DHCP to PPPoE.

  Public static IP and Port Forwarding have nothing to do with this issue.

  Thanks for your help.

• WRT54G bricks? Help, please!

  I have an old Linksys WRT54G V5, it no longer works. When I plug it on I see a white Flash on the light of Cisco Systems but it disappears, the power button flashes quickly, port 1234 light is on fixed and 3 has a line above it, the demilitarized zone and the WLAN lights are turned off, I can't ping 192.168.1.1 or get any connection with it. I really want to get it fixed!

  I didn't need to do that, you know sometimes it helps when you look around and discover that you are using the wrong powder adapter! LOL, the router acts as it is brick and does not have enough power to do anything. I used one that outputs 6 DC, the right of a DC of 12 outings. I feel stupid!

• How to get the IP address Linksys WRT54GS DHCP assigns to a Wi - Fi connection?

  To connect the Linksys WRT54GS to a demonstration of Microchip DV102411 WiFi Comm card I need the IP address assigned by DHCP. The Administration WRT54GS log is enabled, but there is no incoming or outgoing network activity. The DV102411 can see the SSID linsys scanning for wireless networks and attached to it but once attached, I need to know the address IP of the DV102411 has been given by the WRT54GS.

  You can consult the router DHCP client table.

• Cannot access wireless with linksys WRT54GS router

  Hello

  I just installed a Linksys WRT54GS router on my connection, the problem I have is to be able to access with my wireless on my laptop.

  I kept getting a message saying 'connection unindentified' 'access '. I did most of what is already on your forum that such a power out of my rooter, my modem and such and still nothing. I am able to access wireless with my girlfriend Mac laptop, my playstation 3 and my desktop computer which uses Windows X. I initially thought that it my be a problem with my security but even when the connection is unprotected I still have this error. I am trying to disable the IpV6but that didn't ' dot something or the other.

  My laptop is a Toshiba Qosmio X 300 PQX32C-033019 with Vista and my router is a Linksys WRT54GS to. 6

  Here is my connection connect you, sorry if this is in French:

  Try this-

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER...
  Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...

  On your Vista laptop, first turn off the wireless network connection and restart the laptop, and then enable the wireless connection...

  Then click Start > Control Panel > Network and Sharing Center > manage wireless network and click Add, select manually create a network profile and click Next, enter the name of your network SSID/network, select WEP for security type and enter your 10-digit network key and click Next, it should say 'Connected successfully to _' close all windows , and then restart the laptop, now see if you can connect to the Internet wireless...

• Question to Linksys WRT54G password

  I have a router wireless of linksys WRT54G hard wired to a mac and I use the router to get your laptop online. Everything works beautifully. Now I have an iphone that I want to be able to use the same network on. When I turn on my iphone it finds the router which of course requires a password. I'm going in what I think is the password and it is denied. I am able to connect to the Web page of the router and access all my settings. On the administration tab, there is a place to change the password. I changed this and entered a new password, but the only thing that changes is the password that is used to get access to the web page of Linksys. (the web page that I can enter to change and access settings) am I wrong to think this would be the same password to my iphone application?

  Sorry for the long explanation, just try to give detailed information.

  Thanks in advance.

  Yes, it's the wrong password.  Look under your security settings wireless / wireless and you will find the password requested.  This will be a key/paraphrase or password depending on the encryption you put in place.

• Wireless router to modem Homeportal 1800 HG 2wire Linksys WRT54G with questions

  I have the Linksys WRT54G, and I'm trying to use it as the router to my modem 2wire Homeportal 1800 HG wireless.  The 2wire has four ethernet Sockets in the back marked from 1 to 4 and a telephone jack to connect to the wall for AT & T DSL service.

  I have the phone jack connected, and:

  -an ethernet cable

  -to one of the sockets at the back of the 2wire ethernet

  -to the 'Internet' on the Linksys ethernet jack

  - and an ethernet cable

  -to one of the ethernet (1-4) at the back of the linksys

  -to the ethernet port on the computer

  The Linksys is unable to connect via the modem and reports that it may not get an IP address from the PPPoE server.  (Directly connect to the 2wire works well though.)

  Who am I wrong configuration?

  There is no side effect of bridge mode... It is one of the mode in which the modem function. When the modem is in bridge mode, you cannot go online with the computer connected directly to the modem... and you will get a 169.254.x.x ip address.

  So after you convert the modem into bridge mode, you must do the PPPoE settings on the router to go online via router.

• Port forwarding on Linksys WRT54G

  Hey I have problems with Port Forwarding on my Linksys WRT54G. The port, I need open is 28960. I followed guides and thought I did everything correctly, but his does not work. Here's what I've done so far:

  -J' put a static IP address and took a screenshot of my settings here:
  

  -Here is my page of port forwarding:
  

  -Under the ' security > firewall "tab I unchecked"Block anonymous Internet Requests ".
  -In addition, I tried to adjust the 'DHCP server' for people with reduced mobility
  

  Is there something that I don't forget or do wrong?

  Evreything is fine... Make sure that the DHCP server is activated (do not disable it)...

  The only reason why port forwarding does not work because this port can still report it as "Blocked", this only happens if you have an old firmware on your Linksys router...

  Update the firmware on your router, reset and re - configure from scratch and do port forwarding, see if it works...

  Download the Firmware from here

  Follow these steps to upgrade the firmware of the device: -.
  Open a page in Internet Explorer browser on a computer hard wired to the router...
  In the address bar type - 192.168.1.1... Leave name empty username & password admin lowercase usage...
  Click the 'Administration' tab - then click on the 'Upgrade Firmware' under the tab-here, click on 'Browse' and navigate the .bin firmware file and click on "Upgrade"...
  Wait a few seconds until it shows that "the update is successful," after the upgrade of the firmware, click on "Reboot" and you will be returned to the same page OR it will say 'cannot display the Page.

  Now reset your router:
  Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

• Help Linksys WRT54GS

  For internet acess to my XBOX in the basement, I have a router that is put in place by my computer here. It works very well for a while now, but all of a sudden it doesn't work.

  I have a WRT54GS Linksys with SpeedBooster. On the left of the screen, there is only the rectangle box that you can press on, it says "Cisco Systems" above it. Instead of being gold or whatever the color used to be, it's now a silvery color.

  As far as I know it is, I'm pretty sure that is supposed to be gold. I also reset it, pulled the plug and wait 10 seconds sat there and looked online for ten hours trying to find an answer.

  Help, please.

  This little button is for HER (safe easy installation), once pressed it will automatically change the security settings on the router to WPA security. To turn it off or change your security you need to connect to the router, then make the changes.

  1. log on to internet browser 192.168.1.1

  2. let the emptiness of username and password - admin (default).

  3. click on the tab Wireless and you will find the option to reset security.

  4. then click the sub-tab "wireless security" and make the security changes, as necessary.

• I have a router Linksys WRT54G, a flashing power LED, and it does not connect what either. I downloaded a bin file from Linksys, but cannot open it. Can anyone help? I try to get another computer running for my children. Thank you

  The router will not connect to my computer. He repeats to me check the connections. They' fine rev.

  Hi Tweetytewe,

  This occurs on cable connections and wireless? If this happens on cable connections and wireless and your Windows installations are fine, you should contact linksys support to receive the best support.

  http://www.linksysbycisco.com/US/en/support.

  I hope this helps. Let us know if you have any questions.

  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• WAP54G Setup cannot find router

  I have (or better) a WAP54G 3.1, and a second that is configured as repeaters work.
  Accidentally someone pressed the button-Logo and secure-easy-setup-function enabled - of course, nothing did more work.

  I tried to reconfigure the WAP54G, but I can no longer access.

  I pressed the reset on the back button, but that doesn't help much. Now the situation is:

  The AP has an open, public WIFI named linksys - I can connect through which to the DSLrouter and to the internet.

  But I'm not able to find the WAP54G to configure

  192.168.1.254 IP address fails, no ping, no http. I tried the WLAN connected PC and also those connected by cable. I downloaded the installer, but that also claims he can not find any WAP54G, once both tried from a wired computer and from the PC (connected) wireless, firewalls on computers were off.

  local IPS are 192.168.178.xxx and subnet mask is 192.168.0.0 - and that 'invisible' grace WAP54G wireless connected PC received 192.168.178.1 dhcp 192.168.178.32 address and can access INet

  Anyone have an idea how I can configure the WAP54G?

  Sorry for typo IP, - yes of course faults by default est.245

  I was at my local store - the reason is simply that the misconfigured AP reset button did not work not today.

  Thanks for the help