Linux SD card reader?

Similar Questions

• Xubuntu and internal SD card reader

  I use Xubuntu (Fiesty & Gutsy) on my Portege A100 for several months now, and everything seems to work fine except for my internal SD card reader and the inactive recovery. I managed to solve the problem of the recovery by turning off suspend but haven't found anything + that could help get the work card reader.

  If someone managed to solve this problem?

  In your case, there is only a problem: Toshiba does not support Linux OS and there is no driver that can make the SD card works properly. What you can do is to visit a few pages on Linux on Toshiba laptops. You might find something there.

  http://newsletter.toshiba-tro.de/main/index.html
  http://Linux.Toshiba-DME.co.jp/Linux/index.htm
  http://www.Linux-laptop.NET/Toshiba.html

  Good luck!

• Card reader can't read a map with a large capacity.

  I have a Compaq SR1430NX under XP Home SP3. My card reader does not recognize a micro SD 8 gig used with a microSD adapter. I took the PC of a friend about three weeks ago. It was previously running a Linux platform. I have the drive formatted and installed XP. I downloaded and installed all available drivers and software on the HP/Compaq site and have updated all available on the Microsoft Update site, therefore the date of the NTDB. The card can be read by a PC similar I (home built) and a few laptops I have around.  What else can I tell you? The SR1430NX works well otherwise, except this card.

  rdgfx3 wrote:
  
  

  BH, you mention a registry for a possible solution hack?

  Hello

  TI card reader asked only.

  Kind regards.

• CR504U2 card reader

  Hello.

  I have windows 7 on my current computer (GA-g41m-es2l)

  I found completely decomposed dx2300 microtour format (it has been run by forklift, I guess) and it was mainly trashed.

  http://h18000.www1.HP.com/products/QuickSpecs/12668_div/12668_div.html

  The one I saw had a CR504U2 card reader, so for the intact part, I took it home.

  I connected on the PC which ran from Puppy Linux to test, just to test, and it worked without any problem. 8 gb sd? with 256 MB of CF? and 1 GB MS pro? > absolutely no problem. the usb connector worked.

  So I plugged on my GA-G41m-ES2L:

  I unplugged the pannel x rear usb 2 which was related to F_USB1 (while F_USB2 was connected to the front, irony?). This Panel has been fully occupied, but as I had enough room for USB keys on my motherboard, I took this off.

  Then I inserted the card reader and plugged into F_USB1.

  And it is where all problems begin.

  Card reader runs the USB connector (which is simply a bridge of motherboard), but it doesn't read ANY card.

  With any, I mean simply none of this. not right this FC, no MS pro, SD

  I searched all along, I don't seem to find a driver at all, there is no disc in my disk manager or device manager sees it as hard drive.

  Anyone have any suggestions what to do? It seems strange that Puppy linux recognizes and works with her all the time, so that my windows 7 on ga-g41m-es2l don't.

  (PS Yes, integrated connector will symmetrically 5V - D-0 - D + - and in the other line his 1NC.)

  Detective Conan.

  It really boiled over in my head today, so I took out of the box, unplugged the card reader, started the system, connected, plugged.

  Recognized card reader and work. (!!)

  Still have no idea why na plugged not run when everything first, but at least it works!

  Thanks anyway!

• Lightning to a resolution of the camera the incompatible SD card reader image

  I use the lightning to drive camera SD card with my iPhone 6 more (iOS 9.3.5) and MacBook Pro running Photos:

  Version 1.5 (370.42.0)

  Digital camera RAW 6.20 (856)

  Digital Camera Support RAW 6200 (233)

  Import RAW files from my Olympus EM10 on my iPhone, and then when I discovered the images in the Photos on my Mac I see incompatible resolution information.

  These are two consecutive images taken with identical settings...

  

  Drag the two images of Photos on my desktop (export in JPEG) then they have the correct resolution information...

  

  Also interesting. If I import these pictures directly on my Mac via the built in card reader, I do not see this problem.

  OK - when you import on an IOS device (the exact details are better ask in the forum iPad since it does not involve the Mac or Photos for the Mac somehow - it's strictly an IOS feature) in certain circumstances the maximum resolution is 2400 x 3200

  Your best solution is to import directly to your Mac

  LN

• air2 and iPad photo card reader

  I have an iPad 2 air. If. Load my photos on my iPad with the apple photo card reader / accessory... I'll be able to remove the ones I don't want iPad? and I can create folders on the ipad? Or do I have to use my PC for this? Thank you

  kathrynfromcarp wrote:

  I have an iPad 2 air. If. Load my photos on my iPad with the apple photo card reader / accessory... I'll be able to remove the ones I don't want iPad? and I can create folders on the ipad? Or do I have to use my PC for this? Thank you

  You should be able to remove them. I can't tell you for sure because I don't have a reader, but I suspect that the photos will land at film and anything in Czech Republic, you can remove the iPad.

  As for your second question, Yes. You can make Albums on the iPad. The albums will contain only pointers, the photos will remain in film in order not to remove it. The albums will be more enjoyable you can rearrange the order of the pictures by dragging them.

• Any card reader (driving us license and insurance card we) smart is available for iOS Device?

  I want to develop an application for iOS iPad kiosk for patients where patient can check-in in slippery sound driver's license or insurance card by card reader please suggest me if these (reader) hardware available that can be integrated with iOS app.

  I know it is a barcode scanner because I've seen it used in the elections, a couple of years.

  And there is magnetic tape (square) scanners that people use with their iPads.

  You may simply wish to Google and see what happens. Your question is somewhat a matter of niche, so may not find many answers here.

• El Capitan has taken my SD card reader

  Since my upgrade to El Capitan last week, my sd card reader does not work. She is not in the hardware. I did the reset where you unplug for 30 seconds. I did the control + apple + r + thing p and the card reader worked for only a few days. I can't do nvram and smc reset whenever I want to use the card reader, and I hate to use an external USB card reader.

  My card reader works fine on my 2011 27 "iMac. Have you tried using different cards, and if so have you seen changes?

  If for any reason, you are card reader does not work, then buy a card reader external USB and that should work well.

• My USB 3.0 internal card reader SD and bus have both work to quit at the same time. Need help in restoring

  On my Macbook Pro 13 inch Core I5 2 .6GHz, I just noticed that my SD card reader and USB ports have stopped working. Buses from USB 3.0 and player appear in the information of the reporting system. I tried to reset PRAM and SMC but no luck so far and my Time Machine backup is on a SSD in a USB 3.0 hard drive enclosure. Any ideas how to reset the USB 3.0 Bus and drive? I'm including all system information in case it is useful

  System information:

  Model name: MacBook Pro

  Model identifier: MacBookPro11, 1

  Processor name: Intel Core i5

  Processor speed: 2.6 GHz

  Number of processors: 1

  Total number of cores: 2

  (By heart) L2 Cache: 256 KB

  L3 Cache: 3 MB

  Memory: 8 GB

  Boot ROM Version: MBP111.0138.B17

  : 2.16f68 SCM Version (system)

  USB:

  USB 3.0 Bus:

  Host Controller Driver: AppleUSBXHCILPT

  PCI Device ID:0x9c31

  PCI revision ID:0 x 0004

  The seller ID:0 x 8086 PCI

  Host controller USB Bluetooth:

  Product ID:0 x 8289

  ID:0x05ac of the seller (Apple Inc.)

  Version: 1.18

  Speed: up to 12 Mb/s

  Manufacturer: Apple Inc..

  Location ID:0 x 14330000 / 6

  Available current (mA): 1000

  Current (mA): 0

  Additional operating current (mA): 0

  Built-In: Yes

  Software:

  Presentation of the system software:

  System Version: OS X 10.11.5 (15F34)

  Kernel version: Darwin 15.5.0

  Volume: Macintosh HD to startup

  Boot Mode: Normal

  MacBook Pro name: Stuart computer

  User name: Stuart Berwick

  Ensure the virtual memory: enabled

  Integrity of system protection: enabled

  Since the starting time: 6 minutes

  USB 3.0 Bus:

  
  

  OS X Yosemite: If a USB device does not work

• My SD card reader and USB 3.0 Hub have left both answer but see the place in the information system. How can I make them work again?

  On my Macbook Pro 13 inch Core I5 2 .6GHz, I just noticed that my SD card reader and USB ports have stopped working. They hub and drive appear in the information of the reporting system. I tried to reset PRAM and SMC but no luck so far and my Time Machine backup is on a SSD in a USB 3.0 hard drive enclosure. Any ideas how to reset the hub and the reader? I'm including all system information in case it is useful

  System information:

  Model name: MacBook Pro

  Model identifier: MacBookPro11, 1

  Processor name: Intel Core i5

  Processor speed: 2.6 GHz

  Number of processors: 1

  Total number of cores: 2

  (By heart) L2 Cache: 256 KB

  L3 Cache: 3 MB

  Memory: 8 GB

  Boot ROM Version: MBP111.0138.B17

  : 2.16f68 SCM Version (system)

  USB:

  USB 3.0 Bus:

  Host Controller Driver: AppleUSBXHCILPT

  PCI Device ID:0x9c31

  PCI revision ID:0 x 0004

  The seller ID:0 x 8086 PCI

  Mass storage device:

  Product ID:0 x 1000

  Provider ID:0 8564 x

  Version: 11 h 00

  Serial number: 45H3PTDPV3XSLHKB

  Speed: up to 5 GB/s

  Manufacturer: JetFlash

  Location ID:0 x 14500000 / 9

  Available current (mA): 1800

  Current (mA): 76

  Additional operating current (mA): 0

  Apple keyboard / Trackpad:

  Product ID:0 x 0259

  ID:0x05ac of the seller (Apple Inc.)

  Version: 2.24

  Speed: up to 12 Mb/s

  Manufacturer: Apple Inc..

  Location ID:0 x 14400000 / 2

  Available current (mA): 1000

  Current (mA): 40

  Additional operating current (mA): 0

  Built-In: Yes

  BRCM20702 Hub:

  Product ID:0 x 4500

  Name of the vendor ID:0x0a5c (Broadcom Corp.)

  Version: 1.00

  Speed: up to 12 Mb/s

  Manufacturer: Apple Inc..

  Location ID:0 x 14300000 / 3

  Available current (mA): 1000

  Current (mA): 94

  Additional operating current (mA): 0

  Built-In: Yes

  Host controller USB Bluetooth:

  Product ID:0 x 8289

  ID:0x05ac of the seller (Apple Inc.)

  Version: 1.18

  Speed: up to 12 Mb/s

  Manufacturer: Apple Inc..

  Location ID:0 x 14330000 / 6

  Available current (mA): 1000

  Current (mA): 0

  Additional operating current (mA): 0

  Built-In: Yes

  Software:

  Presentation of the system software:

  System Version: OS X 10.11.5 (15F34)

  Kernel version: Darwin 15.5.0

  Volume: Macintosh HD to startup

  Boot Mode: Normal

  MacBook Pro name: Stuart computer

  User name: Stuart Berwick

  Ensure the virtual memory: enabled

  Integrity of system protection: enabled

  Since the starting time: 6 minutes

  USB 3.0 Bus:

  Manufacturer: Apple Inc..

  Location ID: 0 x 14330000 / 6

  Available current (mA): 1000

  Current (mA): 0

  Additional operating current (mA): 0

  Integrated: Yes

  Model name: MacBook P

  A simple restart of the machine is reset.

  On the hub to try another cable and a different port if possible.

  The SD is constructed in the?  It can be a bit fussy, Reseat the card with a purpose, repeatedly if necessary so that it can recognize it.

• Needed: Thunderbolt for MB Pro slot SD card reader (built in does not work)

  The SD card on my MBP player worked for about 3 connections and died, and looking for here and also reveals, this is a common problem.  So rather than money to waste trying to fix this, I want to just find a simple card reader SD with a thunderbolt connection (I already understood that there is NO firewire drives, my MBP is not USB3.0 and USB 2.0 is much too slow).

  So far, I found a couple of features devices/hubs with connectors USB 3.0 as well as love at first sight, but I want just SD-> love at first sight (must be smaller, cheaper and less complexity to break a day).

  So: recommendations for a SD card to the connector Thunderbolt?

  What year, make and model machine do you use?

• Lightning to SD card reader

  I am looking to buy a Flash SD card reader cable. While searching I came across two similar wires:

  1 lightning Apple SD card reader and

  2 SD card card reader from Apple for camera reader SD Apple Lightning lightning

  Can someone tell me if they are a single and even if you please. Thank you very much.

  There is this one http://www.apple.com/shop/product/MJYT2AM/A/lightning-to-sd-card-camera-reader?f node = 91

  and it will let you import pictures from camera sd cards and that's all, you can not install applications and run from it or the likes.

• The right side and express USB card reader does not work

  Hello

  The USB 3.0 right on my rMBP does not work. I have can´t to connect any device to this side. No connection or power.

  Express card reader doesn't work or the other. Finder or disk utility will not show map of mountain.

  I can´t find the card express under system reports reader.

  I ran a test for diagnosis of Apple without any problem.

  I have reset the SMC & LANDAU.

  I reinstalled the operating system without success.

  Anyone who knows how to fix this?

  MacBook Pro with OS X El Capitan 10.11.5, Retina display

  Can someone help me here, please!

  Based on what you have tried and if can't see any device in disk utility, you are dealing with a hardware problem.  Your best option is an appointment at an Apple store for a FREE genius bar.

  Ciao.

• I don't use iPhoto and I want to keep it open automatically when I plug in a device or card reader

  I don't use iPhoto and do not want to open automatically when I plug a card reader or device.

  While the device is connected in Photos, clear the check box to use the pictures from the camera

  LN

• card reader

  Hello

  Bank of mine I have to access the usb card reader, every night is not the card reader. This will make the product not so use full for example to the Netherlands. Here in the Netherlands banks use these PKI cards to identify the end user.

  Concerning

  Eddy

  Nightly Win 64 is far from being a beta version - it's like an pre-alpha , without date version to be released.