list of required access to vpn

Similar Questions

• Unable to connect to other remote access (ASA) VPN clients

  Hello

  I have a cisco ASA 5510 appliance configured with remote VPN access

  I can connect all hosts on the INSIDE and DMZ network, but not able to access other clients connected to the same VPN.

  For example, if I have 2 clients connected to the VPN, customer and CustomerB, with a pool of vpn IP addresses such as 10.40.170.160 and 10.40.170.161 respectively, these two clients are not able to communicate with each other.

  Any help is welcome.

  Thanks in advance.

  Hello

  I'm a little rusty on the old format NAT, but would be what I would personally try to configure NAT0 on the 'outer' interface.

  It seems to me that you currently have dynamic PAT configured for the VPN users you have this

  NAT (outside) 1 10.40.170.0 255.255.255.0

  If your traffic is probably corresponding to it.

  The only thing I can think of at the moment would be to configure

  Note of VPN-CLIENT-NAT0-access-list NAT0 for traffic between VPN Clients

  list of access VPN-CLIENT-NAT0 permit ip 10.40.170.0 255.255.255.0 10.40.170.0 255.255.255.0

  NAT (outside) 0-list of access VPN-CLIENT-NAT0

  I don't know if it works. I did not really have to configure it on any ASAs running older software. There was some similar questions here on the forums for the new format.

  -Jouni

• Divide access remote vpn tunnel ASA 5520

  Hello

  I'm setting up a vpn for remote access with split tunnel, but I use an acl extended to match a host and http to destination port, but does not work.

  Scenario of

  Distance access(10.0.0.122/24)--internet---Cisco ASA(inside:192.168.10.1/24)---ip = 192.168.10.6 - C6509 - 10.0.0.254/24---hote = 10.0.0.31/24

  The plot is when I activate the IP service connection or flow ICMP worked. Does anyone have an idea what is the problem? Thank you

  Concerning

  Split tunneling does not take into account the port information you specify in the ACL, he doesn't care the ip address/network you defined.

  If you want to restrict access to ports and IP, you must define your split tunneling with only ip addresses and using a vpn-filter acl in group policy to restrict following the specific ports that you want:

  split_acl ip access list allow

  access-list allowed filter_acl ip eq

  attributes of group-pol

  Split-tunnel-pol tunnelspecified

  value of Split-tunnel-net split_acl

  VPN-filter value filter_acl

  -heather

• VPN to access LAN VPN clinet.

  We use a PIX 515 as the hub of a LAN to LAN VPN as well as to access VPN Clinet. Using a multipoint configuration sites speaks (all PIX 501) are able to communicate with each other. However, the VPN to access the 515 client are not able to access the VPN sites has talked about. I think that it is due to the fact that put an end to all tunnels on the same interface of the PIX 515. Is there a way to allow the VPN CLient to communicate with the LAN VPN spoke?

  Concerning

  PD

  Currently, it is not a good way to meet the requirements above. However, add us a new item (or rather, a restriction of relax) for the PIX 7.0 code (to be released in December/January) to allow clients VPN packets 'u-turn' on a Hub PIX to PIX spoke connected via Lan-to-Lan tunnels. The program 7.0 beta is about to begin (may have just begun) so if interested, please contact your local account engineer Cisco. Sorry for the news but help is on the way.

  Scott

• 2 VPN SITE to SITE with ACCESS REMOTE VPN

  Hello

  I have a 870 router c and I would like to put 2 different VPN SITE to SITE and access remote VPN (VPN CLIENTS) so is it possible to put 3 VPN in the router even if yes can u give me the steps or the sample configuration

  Concerning

  Thus, on the routers will be:

  

  Cisco 2611:

  LAN: 10.10.10.0/24

  access-list 100 permit ip 10.10.10.0 0.0.0.255 10.10.20.0 0.0.0.255
  

  access-list 100 permit ip 14.1.1.0 0.0.0.255 10.10.20.0 0.0.0.255--> VPNPOOL

  !

  10 ipsec-isakmp crypto map clientmap

  defined by peer 172.18.124.199

  match address 100

  !

  IP local pool ippool 14.1.1.1 14.1.1.254

  !

  access-list 120 allow ip 10.10.10.0 0.0.0.255 14.1.1.0 0.0.0.255
  

  access-list 120 allow ip 10.10.20.0 0.0.0.255 14.1.1.0 0.0.0.255 --> NETWORK REMOTE
  

  !

  crypto ISAKMP client configuration group ra-customer
  

      pool ippool

  ACL 120

  !

  Please note that the configuration is incomplete, I added that relevant changes, you should bring to the allow clients of RA through the LAN-to-LAN tunnel, of course, the LAN-to-LAN settings should match to the other side of the tunnel that is mirror of ACL, NAT and so on.

  HTH,

  Portu.

• Access denied: the IP address of this computer host is not on the list of eligible access of the target.

  Hi all:

  I was working normally with my NI9024 CRIO to my work. I went home and when I came back the other day. I tried to compile my application to work.

  The surprise was that I got a strange message "access denied: the IP address of this computer host is not on the list of eligible access of the target."  Now, I can not connect a CRIO device. I tried to reset all the IP addresses in the CRIO and my PC computer. What can I do?.

  Yes. This is the solution. I had to uninstall the NOR-RIO software on the target. I have uninstall everything on the CRIO. Then I reinstall the software, but I had also to program the fpga, the host and target. And I also have my IP, on the measure and automatition software. I found a big bug I guess.

  Thanks anyway. National Instrument of love. Hope to work there one day.

• Access remote VPN question - hairpin

  Hello, I did a search before posting this question but I have not found anything specific to my situation.

  We have our ASA5520 configured in our main office to allow remote access Cisco VPN client users to access our network.  We have a (network 192.168.1.0/24) remote desktop we have a configured on the same ASA5520 VPN IPSec tunnel that allows the use of internal users (in the main office) to access resources on the network remote (192.168.1.0) and vice versa.  The problem is that when users connect to the remote VPN access, they are not able to access the resources of the remote office network.  We created the nat0 ACL and labour, and split tunnel routing is implemented for users VPN remote network access (if I make a copy of the route on my laptop after connecting to the VPN, I see the road to 192.168.0.0/24 in my routing table).  Routing everything is in place to do this, since the IPSec VPN tunnel is up and working.  My suspicion is that the question has something to do with the consolidation of these VPN clients.

  What else needs to be configured to work?  Thank you.

  Hi Scott,.

  I have a client with a PIX 515E which allows connections to remote VPN and VPN LAN2LAN multiple connections.

  We had this problem too... so what I made in my pix was:

  TEST (config) # same-security-traffic intra-interface permits (its off by default)

  If you use ASDM go to:

  Configuration > Interfaces >

  at the bottom of this page, there is an option that says: 'enable traffic between two or more host computers connected to the same interface '.

  Check and it should work... I hope

  I await your comments...

  Kind regards.

  Joao Tendeiro

• Cannot get the list of role access

  Hi all
  
  I'm new to UCM 11 g. We intend to apply ACLs in 11 g.
  I would like to know how to apply ACLs in the Complutense University of MADRID, I configured ACL according to the Oracle documentation, but how do the user of these ACLs.
  Still something I am unable to get the values in the list of role access.
  
  Thank you all

  Hello

  The value must be added to the view - ExternalRoles.

  Add the publication scheme and test it.

  Thank you
  Srinath

• Access linux VPN client XP host

  Hi all

  I am running VMWare workstation 6.5 on Linux (Gentoo) with a guest of Windows XP. In the host, I connect to a cisco VPN using vpnc and changing tables of road I have access to the VPN as well as the rest of the local network (including the internet). I want to be able to access the VPN connection (i.e. Access IP address provided by the VPN connection) of the XP client. I know that I can use ssh to tunnel of these connections, but I need to configure a tunnel by ip/port that I connect. At the moment the guest is using bridged networks (it has its own IP address on my local network).

  Is the an option of the network configuration in VMWare which will allow the guest to access all interfaces (eth0 and tun0) on the host computer and carry the traffic to these interfaces accordingly?

  Thank you

  Allistar.

  Hello Allistar-

  If you configure the client to use the NAT networking, you will be able to access all networks visible to the host (eth0 and tun0) automatically.  If you need to expose the ports on the outside guest to the host's network, port forwarding can also be configured through the virtual network Editor.

  Good luck

  Mike H

• to provide selective access by VPN.

  If we have two (add1 and add2) Web servers hosted on the area of the DMZ. and we need to give access to only a more remote VPN client (add1) Web server we do. Because when we configure the remote VPN client using PDM. It will never ask for any particular ip address where this configuration will be applied. He asks only what client VPN interface interacts with.

  the current pix configuration should be similar to the one below:

  access-list 101 permit ip 192.168.1.0 255.255.255.0 10.1.1.0 255.255.255.0

  access-list 120 allow ip 192.168.1.0 255.255.255.0 10.1.1.0 255.255.255.0

  NAT (dmz) 0-access list 101

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  ISAKMP identity address

  ISAKMP nat-traversal 20

  Crypto ipsec transform-set esp-3des esp-md5-hmac vpnset

  IP local pool ippool 10.1.1.11 - 10.1.1.21

  vpngroup address ippool vpnclient-pool

  vpngroup idle 1800 vpnclient-time

  vpngroup vpnclient-Server dns 139.130.4.4

  vpngroup vpnclient password cisco456

  vpngroup split tunnel 120 vpnclient

  Crypto-map dynamic dynmap 10 transform-set vpnset

  map remote_vpn 20-isakmp ipsec crypto dynamic dynmap

  Cisco username password cisco123

  AAA-server local LOCAL Protocol

  client authentication card crypto remote_vpn LOCAL

  client configuration address card crypto remote_vpn throw

  client configuration address card crypto remote_vpn answer

  If so, then you just need to change 120, i.e. the split tunneling acl acl:

  Of

  access-list 120 allow ip 192.168.1.0 255.255.255.0 10.1.1.0 255.255.255.0

  TO

  access-list 120 allow host ip 192.168.1.100 10.1.1.0 255.255.255.0

  by changing the acl 120 as shown above, the user remote vpn will accommodate 192.168.1.100 only (all the port/protocol).

  Alternatively, you can restrict access to the level of protocol/port. It requires disabling the command 'sysopt connection permit-ipsec' and then create an inbound acl. I would like to know if it is the most preferred and I'll give you an example configuration.

  Another point should be noticed is that even if the remote user can only access a server in the DMZ, however, you must also restrict access directly on the server. as the vpn remote user may be able to access other private server resources.

• Allowing external IP access via VPN Client

  We are looking for our remote VPN users to access an external IP address.  Basically once users authenticate when they try to access 202.1.56.19, they should be out nat through the external interface of the firewall.  Below is out of the package violated on "vpn ecrypt" tracer and as an extract from the config.  On the client, I see that the road to 202.1.56.19 was added, but it does not work.

  Please advise more information be required ing.  Thank you.

  access list INSIDE-OUT scope ip 10.15.160.0 allow 255.255.255.0 any
  access OUTSIDE list / allowed extended Interior ip 10.15.160.0 255.255.255.0 any
  Access-group OUTSIDE / inside interface OUTSIDE-IDC

  NONATIDC list of allowed ip extended access all 10.15.160.0 255.255.255.0

  NAT (INSIDE) 0-list of access NONATIDC
  NAT (INSIDE) 1 10.15.160.0 255.255.255.0
  Global (OUTSIDE-IDC) 1 128.15.155.2

  internal CorpVPN group strategy
  attributes of Group Policy CorpVPN
  value of server DNS 10.15.155.17
  VPN-idle-timeout no
  VPN-session-timeout no
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list SplitTunnel
  something.com value by default-field

  attributes global-tunnel-group CorpVPN
  address pool CorpVPNpool
  Group Policy - by default-CorpVPN
  IPSec-attributes tunnel-group CorpVPN
  pre-shared key

  Standard access list SplitTunnel allow 192.168.168.0 255.255.255.0
  SplitTunnel list standard access allowed host 202.1.56.19

  Packet-trace input outside-iDC tcp 10.15.160.18 22 202.1.56.19 22

  Phase: 1
  Type: ACCESS-LIST
  Subtype:
  Result: ALLOW
  Config:
  Implicit rule
  Additional information:
  MAC access list

  Phase: 2
  Type: FLOW-SEARCH
  Subtype:
  Result: ALLOW
  Config:
  Additional information:
  Not found no corresponding stream, creating a new stream

  Phase: 3
  Type:-ROUTE SEARCH
  Subtype: entry
  Result: ALLOW
  Config:
  Additional information:
  in 0.0.0.0 0.0.0.0 OUTSIDE-IDC

  Phase: 4
  Type: ACCESS-LIST
  Subtype: Journal
  Result: ALLOW
  Config:
  Access-group OUTSIDE / inside interface OUTSIDE-IDC
  access OUTSIDE list / allowed extended Interior ip 10.15.160.0 255.255.255.0 any
  Additional information:

  Phase: 5
  Type: IP-OPTIONS
  Subtype:
  Result: ALLOW
  Config:
  Additional information:

  Phase: 6
  Type: CP-PUNT
  Subtype:
  Result: ALLOW
  Config:
  Additional information:

  Phase: 7
  Type: VPN
  Subtype: ipsec-tunnel-flow
  Result: ALLOW
  Config:
  Additional information:

  Phase: 8
  Type: VPN
  Subtype: encrypt
  Result: DECLINE
  Config:
  Additional information:

  Result:
  input interface: OUTSIDE-IDC
  entry status: to the top
  entry-line-status: to the top
  output interface: OUTSIDE-IDC
  the status of the output: to the top
  output-line-status: to the top
  Action: drop
  Drop-reason: flow (acl-drop) is denied by the configured rule

  Essentially, the traffic needs to make a u-turn at ASA outside interface if I understand your configuration.

  You need the following to make it work.

  -permit same-security-traffic intra-interface

  -Host202 of the 10.15.160.0 ip access list permit 255.255.255.0 host 202.1.56.19

  -nat (OUTSIDE-IDC) 1 access-list Host202

• Table of DB tools list: how to access tables that are in the different SQL database?

  Hi all

  I work on an implementation of database (SQL server) and evaluates the Toolkit OR DB for this project.

  One of the requirements is that I need access to the tables that are in two different database

  (say Table to 1 DB and Table B to 2 DB).

  Our IT guy linked table in DB1 to DB 2 and I verfied this when I use the SQL server management studio.

  When DB 2 tables is filled, table from DB1 is also there. I can also do the same thing using MS Access.

  Table A of the DB1 is available for me enven if I only connect to 2 DB.

  Here comes the problem.

  When I use DB tool list Table.vi to access DB2, it does NOT list A table in DB1. It list only the tables in

  the database (DB2) which I am connection (using DB tool opened Connection.vi with a file DSN)

  So my work around right now is to open a separate connection both DB1 and DB2. However, this approach

  obviously creates a problem when I have to access a separate database constantly in my application.

  What would be a solution to this? I have search the Forum but only to see a post that is somewhat related to

  My question. (And it was published the 2004) Maybe I need to change the code in the orignial VI (DB tool list Table.vi)?

  My computer guy told me that he has not met this scenario since he wrote code in another environment such as

  VB and others and it has always been successful in linking the different database tables.

  I hope my question is clear and healthy because I don't really know much about database terminology.

  Any comment or suggestion is appreciated!

  Thank you

  Chad

  Ok.  Here is some information that I can work with.  Good.

  Your COMPUTER staff created a view called "VISUAL_WORK_ORDER".

  A view isn't a table.  It is a "virtual" table  Views are used to collect data (usually) in several different tables.

  But I guess that the code inside the DB tool list Table.vi returns a list of tables.  Views are not the tables.  Then "VISUAL_WORK_ORDER" does not appear in the list.

  HOWEVER, this should not really matter.  The view is here!  And it can be queried like any table.  So, you can use DB tools Select Data.VI... and wire in "VISUAL_WORK_ORDER" as the name of the table.  This will return the contents of the view.  Alto!

• Unable to access the VPN Client LAN

  I configured a 877 for VPN Client Access. The Client authenticates and connects and receives an IP address off the coast of the pool of intellectual property. However, he is unable to access anything on the IP network.

  I have included my router config. The VPN Client is v5.0.05.0290.

  Any ideas on what I'm missing?

  Can try reverse our ACL VPN-Client, I think that it is written in the wrong way

  For example:

  VPN-Client extended IP access list

  Note * permit VPN Client pool *.

  IP enable any 192.168.201.0 0.0.0.255

  or more precise

  VPN-Client extended IP access list

  Note * permit VPN Client pool *.

  192.168.1.0 255.255.255.0 ip permit 192.168.201.0 0.0.0.255

• No internet access through VPN

  Hi, I have the router Cisco 881 (MPC8300) with c880data-universalk9 - mz.153 - 3.M4.bin when users establish a VPN connection to the corporate network, had access to all the resources but no internet access, please help me what else I need to configure to achieve my goal. I don't want to split the tunnel, internet via VPN, users must have. In my opinion, I have put an additional configuration for NAT, but my router not recognize u-Turn and NAT commands on the object on the network.

  My config:

  Building configuration...

  Current configuration: 13562 bytes
  !
  ! Last configuration change at 09:52:38 PCTime Saturday, May 16, 2015, by admin
  version 15.3
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  XXX host name
  !
  boot-start-marker
  start the flash system: c880data-universalk9 - mz.153 - 3.M4.bin
  boot-end-marker
  !
  !
  logging buffered 51200 warnings
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authentication login ciscocp_vpn_xauth_ml_2 local
  AAA authorization exec default local
  AAA authorization ciscocp_vpn_group_ml_1 LAN
  AAA authorization ciscocp_vpn_group_ml_2 LAN
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  iomem 10 memory size
  clock timezone PCTime 1 0
  PCTime of summer time clock day March 30, 2003 02:00 October 26, 2003 03:00
  !
  Crypto pki trustpoint TP-self-signed-1751279470
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 1751279470
  revocation checking no
  rsakeypair TP-self-signed-1751279470
  !
  !
  TP-self-signed-1751279470 crypto pki certificate chain
  certificate self-signed 01
  XXXX
  !
  !
  Protocol-IP port-map user - 2 tcp 8443 port
  user-Protocol IP port-map - 1 tcp 3389 port
  !

  !
  !
  !
  IP domain name dmn.local
  8.8.8.8 IP name-server
  IP-server names 8.8.4.4
  IP cef
  No ipv6 cef
  !
  !
  license udi pid CISCO881-K9 sn FCZ174992C8
  !
  !
  username privilege 15 secret 5 xxxx xxxx
  username secret VPNUSER 5 xxxx
  !
  !
  !
  !
  !
  !
  type of class-card inspect sdm-nat-user-protocol--2-1 correspondence
  game group-access 105
  corresponds to the user-Protocol - 2
  type of class-card inspect entire game SDM_AH
  match the name of group-access SDM_AH
  type of class-card inspect entire game PAC-skinny-inspect
  Skinny Protocol game
  type of class-card inspect entire game SDM_IP
  match the name of group-access SDM_IP
  type of class-card inspect entire game PAC-h323nxg-inspect
  match Protocol h323-nxg
  type of class-card inspect entire game PAC-cls-icmp-access
  match icmp Protocol
  tcp protocol match
  udp Protocol game
  type of class-card inspect entire game PAC-h225ras-inspect
  match Protocol h225ras
  type of class-card inspect entire game SDM_ESP
  match the name of group-access SDM_ESP
  type of class-card inspect entire game PAC-h323annexe-inspect
  match Protocol h323-annex
  type of class-card inspect entire game PAC-cls-insp-traffic
  match Protocol pptp
  dns protocol game
  ftp protocol game
  https protocol game
  match icmp Protocol
  match the imap Protocol
  pop3 Protocol game
  netshow Protocol game
  Protocol shell game
  match Protocol realmedia
  match rtsp Protocol
  smtp Protocol game
  sql-net Protocol game
  streamworks Protocol game
  tftp Protocol game
  vdolive Protocol game
  tcp protocol match
  udp Protocol game
  type of class-card inspect the correspondence SDM_GRE
  match the name of group-access SDM_GRE
  type of class-card inspect entire game PAC-h323-inspect
  h323 Protocol game
  type of class-card inspect correspondence ccp-invalid-src
  game group-access 103
  type of class-card inspect entire game PAC-sip-inspect
  sip protocol game
  type of class-card inspect correspondence sdm-nat-https-1
  game group-access 104
  https protocol game
  type of class-card inspect all match mysql
  match the mysql Protocol
  type of class-card inspect correspondence ccp-Protocol-http
  http protocol game
  type of class-card inspect entire game CCP_PPTP
  corresponds to the SDM_GRE class-map
  inspect the class-map match PAC-insp-traffic type
  corresponds to the class-map PAC-cls-insp-traffic
  type of class-card inspect entire game SDM_EASY_VPN_SERVER_TRAFFIC
  match Protocol isakmp
  match Protocol ipsec-msft
  corresponds to the SDM_AH class-map
  corresponds to the SDM_ESP class-map
  type of class-card inspect correspondence ccp-icmp-access
  corresponds to the class-ccp-cls-icmp-access card
  type of class-card inspect the correspondence SDM_EASY_VPN_SERVER_PT
  corresponds to the SDM_EASY_VPN_SERVER_TRAFFIC class-map
  !
  type of policy-map inspect PCB - inspect
  class type inspect PCB-invalid-src
  Drop newspaper
  class type inspect mysql
  inspect
  class type inspect PCB-Protocol-http
  inspect
  class type inspect PCB-insp-traffic
  inspect
  class type inspect PCB-sip-inspect
  inspect
  class type inspect PCB-h323-inspect
  inspect
  class type inspect ccp-h323annexe-inspect
  inspect
  class type inspect ccp-h225ras-inspect
  inspect
  class type inspect ccp-h323nxg-inspect
  inspect
  class type inspect PCB-skinny-inspect
  inspect
  class class by default
  drop
  type of policy-card inspect sdm-license-ip
  class type inspect SDM_IP
  Pass
  class class by default
  Drop newspaper
  type of policy-card inspect sdm-pol-NATOutsideToInside-1
  class type inspect sdm-nat-https-1
  inspect
  class type inspect sdm-nat-user-protocol--2-1
  inspect
  class type inspect CCP_PPTP
  Pass
  class class by default
  Drop newspaper
  type of policy-card inspect PCB-enabled
  class type inspect SDM_EASY_VPN_SERVER_PT
  Pass
  class class by default
  drop
  type of policy-card inspect PCB-permits-icmpreply
  class type inspect PCB-icmp-access
  inspect
  class class by default
  Pass
  !
  safety zone-to-zone
  security of the area outside the area
  ezvpn-safe area of zone
  zone-pair security PAC-zp-self-out source destination outside zone auto
  type of service-strategy inspect PCB-permits-icmpreply
  zone-pair security PAC-zp-in-out source in the area of destination outside the area
  type of service-strategy inspect PCB - inspect
  source of PAC-zp-out-auto security area outside zone destination auto pair
  type of service-strategy inspect PCB-enabled
  sdm-zp-NATOutsideToInside-1 zone-pair security source outside the area of destination in the area
  type of service-strategy inspect sdm-pol-NATOutsideToInside-1
  in the destination box source sdm-zp-in-ezvpn1 ezvpn-pairs area security
  type of service-strategy inspect sdm-license-ip
  source of sdm-zp-out-ezpn1 of security area outside zone ezvpn-zone time pair of destination
  type of service-strategy inspect sdm-license-ip
  safety zone-pair sdm-zp-ezvpn-out1-source ezvpn-zone of destination outside the area
  type of service-strategy inspect sdm-license-ip
  safety zone-pair source sdm-zp-ezvpn-in1 ezvpn-area destination in the area
  type of service-strategy inspect sdm-license-ip
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 2
  BA aes 256
  preshared authentication
  Group 2
  !
  Configuration group customer crypto isakmp Domena
  key XXXXXX
  DNS 192.168.1.2
  Dmn.local field
  pool SDM_POOL_1
  Save-password
  Max-users 90
  netmask 255.255.255.0
  banner ^ Cwelcome ^ C
  ISAKMP crypto ciscocp-ike-profile-1 profile
  match of group identity Domena
  client authentication list ciscocp_vpn_xauth_ml_2
  ISAKMP authorization list ciscocp_vpn_group_ml_2
  client configuration address respond
  virtual-model 1
  !
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac ESP_AES-256_SHA
  tunnel mode
  !
  Profile of crypto ipsec CiscoCP_Profile1
  game of transformation-ESP_AES-256_SHA
  set of isakmp - profile ciscocp-ike-profile-1
  !
  !
  !
  !
  !
  !
  !
  interface Loopback0
  IP 192.168.9.1 255.255.255.0
  !
  interface FastEthernet0
  no ip address
  !
  interface FastEthernet1
  no ip address
  !
  interface FastEthernet2
  no ip address
  !
  interface FastEthernet3
  no ip address
  !
  interface FastEthernet4
  Description $ETH - WAN$ $FW_OUTSIDE$
  IP x.x.x.x 255.255.255.248
  NAT outside IP
  IP virtual-reassembly in
  outside the area of security of Member's area
  automatic duplex
  automatic speed
  !
  type of interface virtual-Template1 tunnel
  IP unnumbered Loopback0
  ezvpn-safe area of Member's area
  ipv4 ipsec tunnel mode
  Tunnel CiscoCP_Profile1 ipsec protection profile
  !
  interface Vlan1
  Description $ETH_LAN$ $FW_INSIDE$
  IP 192.168.1.1 255.255.255.0
  IP access-group 100 to
  IP nat inside
  IP virtual-reassembly in
  Security members in the box area
  IP tcp adjust-mss 1452
  !
  local IP SDM_POOL_1 192.168.10.10 pool 192.168.10.100
  IP forward-Protocol ND
  IP http server
  23 class IP http access
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  The dns server IP
  IP nat inside source list 3 interface FastEthernet4 overload
  IP nat inside source static tcp 192.168.1.3 interface FastEthernet4 443 443
  IP nat inside source static tcp 192.168.1.2 8443 interface FastEthernet4 8443
  IP route 0.0.0.0 0.0.0.0 X.x.x.x
  !
  SDM_AH extended IP access list
  Note the category CCP_ACL = 1
  allow a whole ahp
  SDM_ESP extended IP access list
  Note the category CCP_ACL = 1
  allow an esp
  SDM_GRE extended IP access list
  Note the category CCP_ACL = 1
  allow a gre
  SDM_IP extended IP access list
  Note the category CCP_ACL = 1
  allow an ip
  !
  not run cdp
  !
  Note access-list 3 INSIDE_IF = Vlan1
  Note CCP_ACL category in the list to access 3 = 2
  access-list 3 Let 192.168.1.0 0.0.0.255
  Note access-list 23 category CCP_ACL = 17
  access-list 23 permit 192.168.1.0 0.0.0.255
  access-list 23 allow 10.10.10.0 0.0.0.7
  Note access-list 100 Auto generated by SDM management access feature
  Note access-list 100 category CCP_ACL = 1
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq 22
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq www
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq 443
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq cmd
  access-list 100 tcp refuse any host 192.168.1.1 eq telnet
  access-list 100 tcp refuse any host 192.168.1.1 eq 22
  access-list 100 tcp refuse any host 192.168.1.1 eq www
  access-list 100 tcp refuse any host 192.168.1.1 eq 443
  access-list 100 tcp refuse any host 192.168.1.1 eq cmd
  access-list 100 deny udp any host 192.168.1.1 eq snmp
  access ip-list 100 permit a whole
  Note access-list 101 category CCP_ACL = 1
  access-list 101 permit ip 192.168.1.0 0.0.0.255 any
  Note access-list 102 CCP_ACL category = 1
  access-list 102 permit ip 192.168.1.0 0.0.0.255 any
  Note access-list 103 CCP_ACL category = 128
  access-list 103 allow the ip 255.255.255.255 host everything
  access-list 103 allow ip 127.0.0.0 0.255.255.255 everything
  access-list 103 allow ip 93.179.203.160 0.0.0.7 everything
  Note 104 CCP_ACL category = 0 access-list
  IP access-list 104 allow any host 192.168.1.3
  Note access-list 105 CCP_ACL category = 0
  IP access-list 105 allow any host 192.168.1.2

  -----------------------------------------------------------------------
  ^ C
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  access-class 102 in
  transport input telnet ssh
  line vty 5 15
  access class 101 in
  transport input telnet ssh
  !
  !
  end

  I'd be grateful for help

  concerning

  Hello

  Enter the subnet pool VPN to access-list 3 for source NAT

  You may need to check the firewall also rules to allow the connection based on areas you

  HTH,

  Averroès

• Cisco IOS - access remote VPN - route unwanted problem

  Hello

  I recently ran into a problematic scenario: I am trying to connect to a remote LAN (using a Cisco VPN client on my windows xp machine) my office LAN and access a server there. The problem is that I need a remote local network access at the same time.

  Remote LAN: 172.16.0.0/16

  LAN office: 172.16.45.0/24

  Topology:

  (ME: 172.16.10.138/25) - (several subnets form 172.16.0.0/16) - (Internet cloud) - (VPN-Gateway) - (172.16.45.0/24) - (TARGET: 172.16.45.100)

  To provide access, I configured a VPN to access simple distance on a 1700 series router. It's the relevant part:

  (...)

  crypto ISAKMP client config group group-remote access

  my-key group

  VPN-address-pool

  ACL 100

  IP local pool pool of addresses-vpn - 172.16.55.1 172.16.55.30

  access-list 100 permit ip 172.16.45.100 host 172.16.55.0 0.0.0.31

  (...)

  The configuration works fine, I can access the 172.16.45.100 server every time I need to. However, the problem is that when the VPN connection is connected, Windows wants to somehow rout the packets intended for 172.16.0.0/16 through the VPN tunnel. This is apparently due to a static route that added by the Cisco VPN Client and all other specific VPN routes.

  I suspect that the culprit is the IP LOCAL POOL, since when the VPN is connected, debugging of Client VPN log shows something like "adapter connected, address 172.16.55.1/16. Focus on the part "/ 16". I checked the VPN status page and the only road indicated there was "172.16.45.100 255.255.255.255" under remote routes. Local routes was empty.

  Is this a known problem I missed the obvious solution for? Is there no workaround apart from the pool local vpn penetrating high-end 10.x.x.x or 192.168.x.x? Thank you in advance for advice or tips!

  Hello

  The best way is to avoid any overlap between the local network and VPN pool.

  Try 172.17.0.0/16, is also private IP address space:

  http://en.Wikipedia.org/wiki/Private_network

  Please rate if this helped.

  Kind regards

  Daniel