ListView does not populate when entered second time

Similar Questions

• Screen saver does not react when I "wiggle" the mouse or press "Esc"; 'Enter', etc.

  I had the same screen saver running for centuries (it goes right through my photos), but in the last few weeks, I am unable to find the screen to 'wake up' 'wiggle' of the mouse or press "Esc"; 'Enter' etc etc.  Its very frustrating because I have to press several keys at random and then wait about 5 minutes for the screen saver turns off.  I'm still on Windows 7 and it is up to date.

  No idea how to get the screensaver to respond normally again?

  Hi Christine,

  I understand that your computer screen saver does not react when you move the mouse or press ESC.

  This problem may be due to the following reasons:

  • Several processes that run in the background.
  • Problem with screen saver.

  Please follow the methods and check them off below if it helps:

  Method 1: Clean boot

  IF this problem is caused by several programs running in the background, clean boot will help you understand.

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  How to perform a clean boot in Windows
  

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, consult this section «How to reset the computer to start normally after a boot minimum troubleshooting»

  Method 2: Change the default screen saver

  Please refer to the following article which will help you change the wallpaper and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows7/change-screen-saver

  Hope this information helps, for assistance please answer.

• Here's a strange. I have a HTML page with this time a wmv video. It works perfectly from a USB stick or SD card, but does not work when they are copied to the hard drive

  I have an HTML page created with web expression 4. It contains only a wmv video. It works perfectly when it is called from a USB stick or SD card, but does not work when they are copied to the hard drive. The results are the same with IE and Firefox. It don't make no difference if I use Media Player V9 or V11. He has no control on the page Media Player. Video and html files are in the same directory. Here is the code snippet:

  LIFT, DRAG, THRUST and GRAVITY

  
  

  
  
  

  If I run it on a machine with Win 7 there is no problem.

  Richard Grosser

  Hi Richard c. Grosser,.

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Microsoft Expression forums.

  http://social.expression.Microsoft.com/forums/en-us/categories

• Problems with the .exe file programs + System Restore does not respond when you click

  I have Windows Vista. This problem started a week ago. I tried at first to use my "ccleraner" already installed, but this program does not open when you click on it. I was asked to choose the program that the application to use to open it. This has also happened when clicking on itunes. My avast program when you click also asked which application is required to open it. When it finally scanned my system it does no propblems. In addition, I tried to turn on windows defendrer as he told me that it was off. Clicked on 'Turn on..' and nothing happened. Help!

  Hello

  See the following message to solve the problem of .exe if necessary once you are sure that the system is clean.

  Try Mode safe mode with networking - repeatedly, press F8 that you start.

  The best two methods allow scanners to run and/or AV.exe out of the way or removing.

  1.
  CTRL SHIFT ESC - task manager OR right click on the taskbar - task manager

  Process tab - complete the process on AV. EXE and continue with the uninstall Guide.

  If necessary use start - computer or Windows Explorer to navigate to

  C:\Program Malwarebytes Anti - Malware\mbam.exe or where it is installed - if
  necessary right click on the shortcut of Malwarebytes - Properties - tab - target line to see where it
  is installed.

  Right-click on it and rename it to ZZMbam.COM (or something different than now), then
  Double-click it and run it like this. You can rename it back later. Do the same with others
  programs as needed. Use this method for other necessary - DO NOT ASSUMER one
  program removes all or that there is no other malware.

  ---------------------------------------------------

  2.
  Another method is to use them:

  Use Process Explorer to "Suspend" the process will not stop

  Then use AutoRuns to delete the malicious program startup items.

  Now use UnLocker to delete the files in the malware.

  You may need to do a file at a time.

  Process Explorer - free
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  AutoRuns - free
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

  UnLocker - free (do not install the adaware Ebay)
  http://www.Softpedia.com/get/system/system-miscellaneous/unlocker.shtml

  AV.exe

  ==============================================

  There are MANY varieties of these with many names, but all can be eliminated with the same methods:
  
  Win 7 Antispyware 2010 XP Internet Security 2010 and Vista Antivirus 2010 is rogue antivirus.
  scams to get you to pay for them while they have no advantage at all.

  How to remove all THE varieties of this malware - please read carefully the removal Instructions.
  http://www.bleepingcomputer.com/virus-removal/remove-antivirus-Vista-2010

  RENAME this as necessary to allow them to perform: (use a different name with the extension .COM instead of .exe)
  
  It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run the
  in the regular when windows you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone. (If Rootkits
  UnHackMe execution)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can download
  here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with other security programs.
  It is a single scanner, VERY EFFICIENT, if it finds something to come back here or use Google to see
  How to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software (viruses,
  Trojan horses, rootkits, etc.). that has infected your computer despite all security measures that you have
  taken (such as the anti-virus software, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  http://OneCare.live.com/site/en-us/default.htm

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also do to the General corruption of cleaning and repair/replace damaged/missing system files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• The slide show feature does not work when I used my Apple TV new 4th gen. I have all the minimum requirements for Macbook and Macbook OSX the Airport express. The slide show starts and stops after that 7 photos are displayed on the TV. If I change the

  The slide show feature does not work when I used my Macbook with new Apple TV 4th gen. The slide show stops after that display 7 photos and display to select the options for the slide show is displayed on the screen. The selected interval was 5 seconds. If the interval is spent in 3 seconds the slide show would work for a time and then to display random images. Has worked with Apple on this issue Support Mike and he managed to reproduce the problem. Since I'm in the return period of 14 days for this product, I returned it to the Apple store

  Welcome to the Apple community.

  After returning, I'm not really clear on what your question.

• While the loop does not stop when the two values are equal using equal to comparitor

  Hello world

  I have a really, really strange bug. I have a LabVIEW VI that change a chain on a power supply. I have a start and a stop voltage and use a while loop to increment the device. For example if I want to scan from 1, 2V to 2.2 V in 0.2 V incremements, the program will end when "The current tension" = "stop the tension." And it works very well!

  However, when I start - 3 V and want to stop to say-0.8 (new in 0.2 V incremements) the program does not stop when "The current tension" = "stop the tension." I checked with the probe close to what should be the end of the race and - 0.8 V goes both of the entries ' equal to ' comaprison operator, but that his can't trigger a real result.

  It's very strange for me. Espeically as if I'm going - 0.8 V to-2 V but decrement of-0.2 V, the program stops correctly!

  I am very confused!

  See you soon!

  Search on: comparison of floating-point numbers

  The second thread is particularly relevant. This discussion was 2009, but you can find that the same "bug" being reported to enter the end of the 1980s.

  Mike...

• HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  The battery is dead. When I try to turn on the laptop by plugging the AC adapter does not charge or led power LED does not turn on. But when I press the power button, the power, the indicator flashes and turns off (when power adapter connected).

  (1) I tried the press and holding the power button for 30 seconds after removing the battery & AC adapter / CC.

  (2) I tried to change the power adapter too.

  The problem is that it is.

  Your advice is very much appreciated.

  Thank you best regards &,.

  Zia

  Dear customer,

  Welcome and thanks for posting your question on the Forum of Support HP

  It seems that you are not able to turn on the laptop and tried to solve the problem

  Please perform steps listed to find out if it is a hardware or software problem below:

  1. remove all cables and devices, disconnect them and try to turn on the device

  2. check the LED light situation and ensure the action of the spring button / stop is normal

  3 Exchange with a well known power cord and the AC adapter

  4 Pack no adapters are available, check if the power adaptor is slightly warm

  Note: This will give us an indication that the power adapter could be good

  5. do you know if the laptop was in battery or power adapter when you used the last time

  Note: Make sure that there is no spill of liquid or cutting

  6. check if the Port of the AC adaptor is loose/broken

  Note: If the laptop is not on even with a power adapter well known, this confirms the hardware failure with the system board or power DC Circuit

  Hope this helps for other queries to answer the post and feel free to join us again

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  I work on behalf of HP

• Question 1: The button "Buy now" does not work when you select a plan. Question 2: Can not select "Monthly Plan" for a "unique App."

  Question 1: The button "Buy now" does not work when you select a plan.

  How to reproduce the problem:

  1. go in terms of pricing and membership creative cloud | Adobe Creative Cloud

  2. choose a plan, then click on 'buy now '.

  3. you go to a blank page instead of the next steps in the payment.

  Question 2: Can not select "Monthly Plan" for a "unique App."

  How to reproduce the problem:

  1. go into "https://creative.adobe.com/plans".

  2. under "Unique App", select a product and then try to select the "monthly Plan" in the second menu drop-down.

  3. for some reason, it isn't get selected and the price is replaced with the ellipsis (...). I expect the monthly price to appear.

  Please notify.

  Thank you.

  Contact adobe during the time pst support by clicking here and, when available, click on "still need help," http://helpx.adobe.com/x-productkb/global/service-ccm.html

• In number. How do I lock you in a function such as highlighting a cell so it does not disappear when you move to another cell.

  In number. How can I lock you in a function such as highlighting a cell so that it does not disappear when you move to another cell.

  Hi Philil,

  Do you mean pointing out the contents of a cell, or "stressing" the cell itself (by placing an on bottom border)?

  Formatting content will transfer to another cell if you fill in the other cell content, or copy from a single cell and pasting it into another.

  Borders applied to a cell or group of cells may be applied to another cell or group of cells by selecting the first cell (single click), the format of this cell or a group of cells copy (Format (menu) or option + command + C > copy Style), and then selecting one or more other cells and stick to the format (Format (menu) or command-option-v > paste Style.)

  'Format' in the case of cells includes the color fill, color text and other text attributes, content, format (text, number, date & time, duration...), borders...

  When you copy the style, all format attributes are copied.

  Kind regards

  Barry

• Modules window does not appear when selected in Tools/Addons except new open first tab

  Addons window does not open when selected Tools/Addons, except new (empty) tab was selected first. Is there a fix or is this a bug

  This has happened

  Each time Firefox opened

  == upgraded to 3.0

  It is a problem with one of your modules, Mr Tech Toolkit, it is a known problem, but I don't know any solution, although there are workarounds.

  In Mr Tech Toolkit options, under the section "Manager Hacks > Behaviour ', you will have to"select target window' set to 'new tab '. One solution is to change to 'new window '.

  An alternative is to use a bookmark to open Bookmark Manager modules in a tab at the following location:
  chrome://mozapps/content/extensions/extensions. XUL

• Tecra M5 does not record the date and time - battery RTC or CMOS checksum is inconsistent

  My Tecra M5 PTM50E reverend new does not record the date and time. I loaded RTC battery for 8 hours when electricity is on in the said user's manual. I don't know where is the problem. The BIOS settings are respect after power is on.

  When I change any value in the BIOS, the changes are saved properly but date & time system restored to their value 01/01/2000, 00:00 every time when I get out of turning off more of 2-3 min. Message "RTC battery is low or CMOS checksum is inconsistent.

  Press [F1] to set Date/time"does not appear when I power on the computer. Any suggestions?

  Hi guys

  Usually this problem appears only if the CMOS (real time clock) battery is empty or corrupted.
  The real time clock battery powers the internal clock in real time and calendar. It also maintains the system configuration. If the RTC battery is completely discharged, the system loses these data and the real-time clock. In this case, the message RTC battery is low or CMOS checksum is inconsistent appears.

  So I see only two possibilities:
  Either you will charge the battery for real-time clock, or you ask the technician for replacement.

  Generally, the battery must be completely charged after 8-9 hoers but try to connect the laptop to the power adapter for a long time.
  If it will not help solve the problem if you contact the ASP for the RTC battery replacement.

• My cd-writer/DVD disc tray does not open when I press the Open button. He is not blocked and has no disk in it. How can I me t to operate?

  Cd-writer/DVD disc tray does not open when you press the Open button, or when you use the buttons to control the media on the keyboard. How can I restore it to its operating state?

  Hi John,.

  Please let me know exactly what happened when you tried my suggestions of first and second.

  Of your most recent post, looks like you're watching the wrong part of the Device Manager. Optical drive is listed under "readers of CD-ROM/DVD-ROM". The info you gave appear under "drives". If the drive is not listed under "readers of CD-ROM/DVD-ROM" or there is no such section in Device Manager, then Windows do not see. If windows can't see it then this means that there is no power or that the drive is broken.

  When you pushed the drive back in, the player no longer has much of the book or did you have to push all the way. If the latter, it means that the drive has no power or is broken.

  With respect to the opening of the case, I guess I should ask first if it's a laptop or desktop?

  Tricky

• Why my windows freeze and go does not respond when I try to install the msn photo on hotmail download tool?

  Why my windows freeze and go does not respond when I try to install the msn photo on hotmail download tool?

  The active x bar descends into the small window and freezes all windows open right there and will not respond. This happens when I open a new message and try to attach photos.

  Things I tried but has not made a difference:

  reinstalled IE 8, deleted the history of the browser, disk Cleanup, removed msn photo upload control, optimized IE8

  With xp media center

  PS. This occurs also at any time the information down to install an active x on any site control

  The only way to surf now with frustration is to use IE 8 NOT add optional

  So I fixed that on my own and that's how I did it.

  You must uninstall IE 8 completely which will bring you to IE 7 (in my case) and then install IE 8 via the site updates or microsoft.

  Uninstallin IE 8 by going to:

  Start--->

  Control Panel--->

  Add Remove programs--->

  Scroll down to IE 8--->

  Click on delete.

  IE8 updates must be removed also, if not then click the box 'To see the updates' on the top of the window to scroll down, look for the IE 8 security updates and delete.

  Resart your computer and install IE 8.

  This worked for me and may or may not work for you.

• Companion of Xperia does not detect when I unlock my phone

  Companion of Xperia does not detect when I unlock my phone and keeps the dialog box "device is locked" even after that I unlocked the phone.

  I restarted the phone as well as killed processes all XC and rebooted too, but no difference.

  What's wrong?

  Overview running Xperia Z3 and Android N.

  OK, found a solution.

  Developer mode entered,

  Enabled USB debugging

  Again inspected the option 'Select USB Configuration' to 'PSG '.

  Now unlocked XC.

  Weird.

• The mouse pointer does not hide when you type, even with the box checked.

  Hello everyone.  I turned on the check mark in the properties of the mouse "hide the pointer during the strike".  However, the mouse pointer does not hide when typing, but instead remains visible all the time.

  No one knows why this happens?  In previous versions of Windows, the pointer should simply disappear when keystrokes are typed, and then reappear when the mouse is moved.  Is not the case here!

  Thanks for any information!

  System details:

  Windows Vista Ultimate x 64 SP1, 4 GB ram
  Intel Core2 3.16 GHz cpu
  NVIDIA GeForce 8800GT with two monitors
  Aero is enabled.

  Hello

  Welcome to the community of Windows Vista.

  1. what application you are working on when you encountered this problem?

  Hide the mouse pointer option allows you only to remove the mouse curzor of
  the focus in the working window so that the cursor does not cover the text or the pitcure you see.

  Make sure that the curzor of the mouse is placed inside the app as you type, as it does not hide the mouse, if it is outside of the application.

  Change the settings of the mouse
  http://windowshelp.Microsoft.com/Windows/en-us/help/efd700f8-bbc0-4F04-9f78-3bdb4bbf47011033.mspx#EKD

  Kind regards

  Technical support of Microsoft-yama.
  Visit our Microsoft answers feedback Forum and let us know what you think.