loading at startup static data, advice please

Similar Questions

• My MacPro will not start. I get a gray and white screen. Continues to try to restart, but never done! Advice please.

  Care of my MacPro is lower from a previous post.  It does not start, but keep train.  I get the rope to music if I stop and start again.  Advice please.  Thank you very much.  Allan

  Material Information: ℹ️

  Mac Pro (early 2008) (data sheet)

  Mac Pro - model: MacPro3, 1

  2 3 GHz Quad - Core Intel Xeon processor: 8 strands

  8 GB of RAM expandable

  DIMM Riser B/DIMM 1

  1 GB DDR2 FB - DIMM 800 MHz ok

  DIMM Riser B/DIMM 2

  1 GB DDR2 FB - DIMM 800 MHz ok

  Riser DIMM A/DIMM 1

  2 GB DDR2 FB - DIMM 800 MHz ok

  Riser DIMM A/DIMM 2

  2 GB DDR2 FB - DIMM 800 MHz ok

  DIMM B/DIMM Riser 3

  1 GB DDR2 FB - DIMM 800 MHz ok

  DIMM B/DIMM Riser 4

  1 GB DDR2 FB - DIMM 800 MHz ok

  Riser A/DIMM DIMMS 3

  Vacuum

  Riser DIMM A/DIMM 4

  Vacuum

  Bluetooth: Old - transfer/Airdrop2 not supported

  Wireless: en2: 802.11 a/b/g/n

  Video information: ℹ️

  NVIDIA GeForce 8800 GT - VRAM: 512 MB

  HH281 1920 x 1200 @ 60 Hz

  DELL3007WFPHC 1600 x 2560

  System software: ℹ️

  OS X 10.10.2 (14C109) - since the start time: 20:27:26

  Disc information: ℹ️

  ST3320820AS_P disk0: (320,07 GB)

  EFI (disk0s1) : 210 MB

  Disc 1 - system (disk0s2) /: 319,21 GB (17,69 GB free)

  HD (disk0s3) [recovery] recovery: 650 MB

  WDC WD5000AAKS-41YGA0 disk2: (500,11 GB)

  EFI (disk2s1) : 210 MB

  System install disks 1 and 2 (disk2s2) / Volumes/installation discs for systems 1 & 2: 16.11 GB (4.40 GB free)

  Disc 2 (disk2s3) / Volumes/disk 2: 483,52 (291,34 free go-go)

  Hitachi HDS721010DLE630 disk1: (1 TB)

  EFI (disk1s1) : 210 MB

  3-1 TB (disk1s2) Dist/Volumes/Dist 3 TB: 999.86 1 GB (328,00 GB free)

  USB information: ℹ️

  Prolific Technology Inc. IEEE-1284 controller.

  Hewlett-Packard HP LaserJet P2055dn

  Hub keyboard Apple, Inc.

  Logitech USB receiver

  Apple, Inc. Apple Keyboard

  Apple Inc. Bluetooth USB host controller.

  EPSON USB printer

  Guardian: ℹ️

  Mac App Store and identified developers

  You still have OSX 10.5.8?

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk if Lion or higher

  OS X: on OS X Recovery - Apple Support

  Otherwise start from the installation DVD and keep the boot disk

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  Run the Apple hardware test. You will need one of the original installation discs

  Using Apple Hardware Test - Apple Support

  You may have a bad graphics card. The NVIDIA GeForce 8800 GT - VRAM: 512 MB are prone to failure

• should I turn off my IKM for faster migration update if I have static data?

  I have no much experience with ODI and I know that sounds like a very long explanation, but if you have experience using ODI respondent should not be that difficult, please bear with me on this one...

  I move data between Postgres, Oracle 12 c. Use my interfases: incremental update for IKM Oracle and IKM Oracle incremental update PL SQL (using long data types). The tables are in the order of several hundred million of 100 million more 500 million lines from wherever we have to run the interfases as soon as possible. Because of my inexperience with ODI, I'm not sure if I select the right options to run the interfaces:

  1 as soon as possible

  2 - with the possible minimum measures

  The aim is only to move static data to Postgres to Oracle, that's all. (there is very few transformations, for most of the castings to force data to a certain type of data)

  With my current selections, the IKM Oracle incremental update (PL SQL) ODI does the following:

  -working table, create work table C$ _0 < TABLE TARGET - >

  -working table charges <-this step loads the postgres data in the oracle table... <-that's ALL I NEED! .. .load of Postgres to Oracle...

  -creates the flow table: I have$ _ < TABLE TARGET - >

  -then using a cursor selects all data from the TABLE of WORK C$ _0, load: I have$ _ < TABLE-TARGET > <-is there a way to avoid all these additional tables?

  -create indexes and statistics on I$ _ < TABLE TARGET - >

  -flags of lines for the realization of the update if the lines already exist in the < TARGET > TABLE

  -Using a cursor selects all I$ __ where IND_UPDATE = 'I' and inserts data into the TABLE < TARGET > < TABLE TARGET >

  My data source are static and its integrity is verified by FK in Postgres, so I'm not worried about the quality of the db of the source, to the IKM my options are:

  Insert is: TRUE

  Update: TRUE <-would it be wrong? (I think this one can be false for me because my source table is static and my target doesn't support only once for the first time is always empty table)

  flow control is FALSE

  static control is FALSE

  Has. are all of the options to reduce the steps performed during the interface? (it seems I need to UPDATE set to false on the revenge for each interface)

  I load a table with 110 millions of rows, work began in 24 hours. To load the table of Postgres to Oracle took 4 hours and 10 minutes, but to load the flow table (PLSQL cursor) took more than 20 hours for barely half of labour (52 million lines)

  All the data I need is on the work table, I can stop the interface and rename the columns but I wonder... B. what is the right action to take here? how to change the settings of the ODI, so they just move the data from the source to the target only and avoid any other measure reducing the total execution time.

  C. the server has 32 processors, but ODI seems to use one. How can I take advantage of the CPU?

  Thanks for your help.

  P.S. I have read all the documentation there, but it is difficult to get concrete responses with no experience using the product and no other indication. I'm learning to use the tool by using the documentation only.

  Hello

  I would check this vlog by Craig Stewart first to see if can do you need:

  http://odiexperts.com/direct-load-by-interface-with-no-work-tables/

  Otherwise, there are a few points I would make:

  You use the bad IKM with a cursor, if you load Oracle and you want to insert / update, then I always would start by merging first.

  Second, feel free to hack the km to get what you want (always duplicate an existing and start from there, he avoids you to come once upgrade). If you look at the LKM, the insert in $ CAN use a different API call to get table name of $ CAN, you can always get the name of the target table (see the appropriate step of revenge for syntax) and to use it in the same place (perhaps to tweak the getColList in the same way) I've done it before - I created a LKM to write directly in the target table , I need an IKM has nothing so used a dummy not (interface complains with no set IKM), not to the customer more, don't have it to hand, but I'm willing to help if you want to PM me.

  For Question C - seems you want o use parallelism, see the Oracle documentation first to get on the same page. You need optimizer parameters set correctly and your tables must be created with parallel hint in the DDL (maybe need to change any ODI create table steps accordingly).

  Try to get the optimizer to get correct PX parameters before you use to alter session strength parallel etc etc.

  Rgrds

  Alastair

• How (really) to stop the tabs from loading at startup until the user clicks.

  I googled. I have read so many answers and tried them all.

  Browser.sessionstore.Restore *.
  Browser.Tabs.Load *.

  None of the related responses actually prevents firefox from loading tabs (home | homepage |) Home page) at startup.

  Then please. As I was five, and in order to preserve for posterity, someone explain how to stop firefox from loading tabs of the homepage automatically at startup. I want to load them when I click on it, or if I close the tab, for not otherwise materially affect the time of start/loan.

  I'm going to mark as resolved to close, but really, I guess I decided it is insoluble. The answer to "How to stop tabs on the home page of loading in the background" is really "why would you do that?

  Mainly, I want to do because I use extra home pages and reminders "view" soon If I bookmark something that he is likely to be forgotten and lost, whereas if I at least see the tab every time I start firefox, I'll deal with it later. I'll have to change this behavior, though, I suppose.

  Browser.sessionstore*-

  My understanding of these parameters after having read the other questions, it's that they don't affect the loading, which were finally open family home page and will be reopened on a new start tabs only if you have firefox set to operate in this way. (Which I did not - if I close a session with 9 tabs, they went and the next start will generate just my home page tabs).

  john99, I appreciate your time and your help.

• Pitch bend wheel on my pc - 300 midi keyboard Roland. The Modulation part works but when I try to pitch bend a note using the same logic of wheel just plays a continuous note. Can someone give me some advice please? Thank you

  Hi, I have a problem with my pitch bend wheel on my pc - 300 midi keyboard Roland. The Modulation part works but when I try to pitch bend a note using the same logic of wheel just plays a continuous note. Can someone give me some advice please? Thank you

  It's a delicate issue... like some patches cannot stipulate pitchbend...

  But to quickly test your pitchbend wheel actually works properly...

  Download the free lunch monitor...

  Snoize: MIDI Monitor

  Run and see if it sees pitchbend data sent by your keyboard... and therefore by logic.

• HP connection manager exe. Could not load the Assembly system.data, Version = 1.0.61.0, culture = SQ Lite...

  have new laptop dv7 and continue to receive the window... HP connection manager exe.

  "Cannot load the Assembly system.data, SQ Lite, Version is 1.0.61.0, culture = neutrral, db937bc2d44ff139 = public key token.

  The application will now exit.

  Please identify your laptop / pc

  Look at the basic/back/side of the pc/laptop to the sticker with barcode.

  Item number of pole 2 as seen on the following example of label with barcode of a HP laptop. The barcode on your HP product may be slightly different in appearance, but will still have important information necessary for us to help you.

  #Do not post not the serial number of your product because it is private and considered to be personal information. ###
  
  Display the version of the operating system installed (State whether 32 or 64 bit) and the processor as one product AMD or Intel

  Not showing information as requested could delay our responses and troubleshooting slow the question that led you to create a thread. We want to help you, so please help us help you.

  Have you gone to your laptop's web support portal and tried the HP software box software?

  This would certainly be a good starting point.

  Removing and reinstalling the software HP Connection manager is also a good plan. It is also located on the web portal of support for your laptop.

  Best regards

  ERICO

• Programtries to load at startup that I'm not sure.

  A startup name program: (5BB4B692-C213-DAD1-E621-571CE305F4CO), file: c:\documents and settings\myname\application data\faagge\cuavt.exe tries to load at startup. What kind of program is this and should I allow this program use or continue to block?

  On Friday, February 11, 2011 16:11:58 + 0000, BenXP333 wrote:

  A startup name program: (5BB4B692-C213-DAD1-E621-571CE305F4CO), file: c:\documents and settings\myname\application data\faagge\cuavt.exe tries to load at startup. What kind of program is this and should I allow this program use or continue to block?

  A search on the web for cuavt.exe can't find anything. This means that he almost
  Certainly a malware infection (either a virus or another type of)
  malicious software). It is very common for malware to generate names at random, since
  the author does not want you to know anything by a web site
  image search.

  Ken Blake (MS-MVP)

• just loading at startup screen but after loading is the screen is completely blank.

  original title: help with a Windows Vista laptop please help.

  When I start my HP Windows Vista laptop, it works very well and just loading at startup screen but after loading is the screen is completely empty. The keyboard works fine and the keyboard lights are on but nothing on the monitor. Help, please? Passing on the black screen the arrow appears, but again, it is all black.

  > @dhhuang they don't tell me because I have no guarantee and it's like over $ 100 just for talking on their phone, which I think is not worth.

  I'm sure you can order a set of recovery disks. You need to talk to a technician to do it. Yes?

• A drive mapped on P to P does not load at startup upward.

  My question is similar, but may have a different answer.  I have a peer-to-peer network and my computer plays the main role.  In the morning he gets turned on first so that other computers can charge the player.  Some of my programs require that the mapped drive is the same on all computers like me.  The problem is that when I turn on my computer, it does not read the drive mapped on himself and he listed as disconnected.  I then manually go and plug.  Again, it is annoying more then anything.  Any suggestions?

  Hi Loreman,

   

  Thanks for posting your question in the Microsoft Community.

  From the descriptions of the question, it seems that mapped drive does not load at startup to the top.

  I imagine the inconvenience that you are experiencing. I'll help you fix the problem.

  Follow the methods and mark the question below:

  Method 1:

  Disable the antivirus software:
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

   

   

  Method 2:

   

  Drive mapped to the network connection may be lost:

  http://support.Microsoft.com/kb/297684

  Warning: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up the registry, click on the number below to view the article in the Microsoft Knowledge Base:

   

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

   

  I hope that the information above helps you.

  Your response is very important for us to ensure a proper resolution.

  In the future if you fall on any question relating to Windows, please do not hesitate to post your request here on Microsoft Community, we will be more than happy to help you.

   

   

   

• Update Verizon iPhone 5 new IOS 10 problem: cannot receive/send calls. Shop Verizon says it's an update causing Apple to popular phones to crash all day. Any input or advice, please?

  Update Verizon iPhone 5 new IOS 10 problem: I can't receive/send calls. The store Verizon says it's phones a popular causing update Apple crash all day. Any input or advice, please?

  Don't you say no service at the top?

• Indicator light charging cable does not go on when connected to power what a lack of cable or battery problem? Advice please. I have

  Indicator light charging cable does not go on when connected to power what a lack of cable or battery problem? Advice please.

  Troubleshooting help here > Apple Portables: Troubleshooting MagSafe adapters - Apple Support

• How to limit the programs that load at startup?

  How to prevent apps will load at startup?

  One place to check: Apple menu > System Preferences > users and groups > click the user in the left sidebar, then the login at the top items.

• my app store on my 6plus does not work... not load materials... Help, please

  my app store on my 6plus does not work... not load materials... Help, please

  Turn off your device and turn it on again. If this does not help, sign out of your account and reconnect.

  In addition, you can try to reset your settings.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

  https://support.Apple.com/en-us/HT201559

• CHKUPD loads at startup. How to find and delete this file?

  CHKUPD loads at startup. How to find and delete this file?

  CHKUPD loads at startup. How to find and delete this file?

  Not a matter of Microsoft/Windows.

  http://answers.Microsoft.com/en-us/search/search?searchterm=CHKUPD&CurrentScope.ForumName=Windows&CurrentScope.filter=windows_xp-files&askingquestion=false

• Error loading c:\windows\wvowikrrevafide.dat

  Error loading c:\windows\wvowikrrevafide.dat
  the specified module could not be found

  This message is displayed on every 2 minutes

  The file is usually used during the uninstallation of a program - they are very common. Due to their nature, they are often reported as potential problems. The entrance of R3 is linked to Yahoo and is legitimate. If you can't fix it yourself, try visiting http://support.microsoft.com/ for help online.