Location of the Raid drivers

Similar Questions

• Impossible to install the Raid drivers from the USB on the Tecra S series

  I tried to install the Toshiba RAID drivers (you know things F6) using a USB and emulating the BIOS USB FDD, well that detected the installation got XP file sytem was unknown.

  Any help?

  Hello

  If you use Windows XP RAID driver cannot be installed on the USB. It is not possible.
  You can install the RAID driver using only the drive FDD USB and floppy.

  But Windows Vista recognizes the USB and the RAID driver might be installed in this environment.

  So what OS and device do you use?

• Tecra S3 XP Setup not find HARD drive even if the RAID drivers were included by F6 key

  I tried to install a normal XP (not recovery). But the installation program will not find my HARD drive even if I include the Toshiba RAID via F6 drivers.

  Any ideas?

  > I have decided to use nLite and added the raid driver but after several installations different combo, I'm done with the original problem which does not recognize my floppy USB drive after format

  If you have included the RAID driver using the nLite so I put t understand why you need the external USB floppy drive?
  Anyway, to my knowledge, not all USB FDD drives are compatible and it can happen that a non supported USB FDD drive will not recognize and so you would not be able to install the RAID floppy driver!

  But nLite is the key! Using the nLite you n t need the USB FDD drive!

• Satellite L45-S742 - cannot install the RAID drivers

  I tried to install a copy of Windows XP on a Satellite L45-S7423 but, whenever I try to install it I get this message:

  [http://209.167.114.38/support/techsupport/tsbs/all/-TSB001272/sata%20pic%201.bmp]

  Now, I tried following the instructions on this Web page

  [http://209.167.114.38/support/techsupport/tsbs/all/-TSB001272.htm]

  But, I always find myself with the same message every time. What can I do to get XP installed?

  Satellite L45-S742 supports RAID functionality?
  I doubt!

  L40/L45 are equipped with a SATA HDD controller and you don't need RAID driver but driver SATA!

  Check here some discussions about the Intel storage Manger and drivers SATA!

  See you soon

• Where to find the RAID for Satellite A300 drivers?

  Hello

  Where can I find drivers for A300 (PSAJ0E) raid?

  Post edited by: ADMIN

  Hello

  I think that you don t need all the RAID drivers.
  As much as I know A300 does not support RAID capacity.

  Your laptop supports the SATA interface, and I assume that you will install the SATA driver.

  The Intel Matrix Storage Manager is a package that contains the SATA driver for two different chipsets
  In order to check the Intel page!

  Concerning

• Slipstreaming windows 2003 with Raid drivers

  Hi all
  I am creating a slipstream disk to install the raid drivers. I did it before using the program n - lite with great success, unfortunately this time it doesn't. So, I checked the forums for how to do it manually. I followed these steps http://support.micro...om/?kbid=288344
  This makes me through loading the driver and restarts, then restarted and enter in install windows server 2003 fails with the error message "an error was encountered, which prevents the installation to continue. internal configuration data is corrupted (phase0). Press ok to view the Setup log"
  The Setup log shows "installation internal data structures are corrupted (phase0).

  Any ideas?

  Hi Tuono,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/winserversetup/threads

• Need help to install on win xp SP2, hp 8300 elite raid drivers?

  I spent to win 7 on HP elite 8300 for win xp sp2. I did this because I had to install a specific software that only works on Windows xp sp2. And now I have the problem with the raid drivers. I need help how to install them, and I don't know if I downloaded the right one.

  Maybe the only solution is to insert sort this driver in the instalation of win xp cd because I don't have floppy drive.

  HP elite 8300

  SERIES:[personal information]

  PRODCT NO.: B0F31EA #AKQ

  Hello:

  Please read the info on the link below on how to integrate the SATA/RAID drivers.  Read the Intel section and read the document about how to integrate all the drivers.

  http://h30434.www3.HP.com/T5/notebook-operating-systems-e-g-Windows-8-and-software/SATA-drivers-for-XP-solution-on-0x0000007B-BSOD/m-p/114120#M17758

  The drivers from the link below allows you to integrate. Second listed file is what you need for XP 32 bit.

  http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=21730&ProdId=2101&lang=eng&OSVersion=Windows%20XP%20 * & DownloadType=.

  The real driver you need is the controller RAID Intel® Express Chipset SATA Desktop/Workstation/Server. But all by wake.

• Data store missing after the reconstruction of the raid array

  One of the players in my raid array has failed a few days ago.

  I had a spare drive in the table so the controller immediately began the process of rebuilding and all servers were running throughout.

  When the reconstruction has been completed (I checked this via the user interface of raid array and the newspaper), I had to stop the server to remove disc defective (not replaceable chassis hot) and when I restarted the server, the data on the raid array store isn't there anymore.  I also checked through the raid controller interface that I removed the (defective) drive and that the table was always in a ready state when he came.

  In vsphere client, when I click on the storage... Add link, the server sees the material but if I click then it tells me that it will be re - format the volume.  See attachment.  I have most certainly does not take the next step and reformat.  Simply, I took the screenshot and regularized.

  I found these instructions, but they are for an older version of ESXi and am unsure if they are correct for ESXi 6.0.0 338124

  VMware KB: Lack of data store after the reconstruction of the RAID disk/LUN

  Here are the steps I should follow?

  If these aren't the right instructions can you tell me the version which is for ESXi 6.0.0 338124 that I couldn't find anything either.

  Thank you

  Hi ThompsG,

  Yes, there are two data stores for the virtual machine located on the RAID array.  The virtual machine itself was stored in a different data store that was not in the raid array.

  I spent about 48 hours last week, including this morning, trying to coax ESXi recognizing volumes, with no luck.  Finally, I gave up and I removed the virtual computer hard drives that were on the corrupt data store.  Then the virtual machine came without problem.

  Finally, since I have everything on these 2 volumes backed up to a cloud provider, I have recreated the two data stores in the raid array and began the restoration process. It is currently running and has about 16 days left to go.

• How do I use the sony vaio VPCEC3S0E built in motion eye camera I have attached looking for the correct drivers but could not locate them

  How do I use the sony vaio VPCEC3S0E built in motion eye camera I have attached looking for the correct drivers but could not locate them

  Hello

  Troubleshoot camera connection
  http://Windows.Microsoft.com/en-us/Windows7/Troubleshoot-camera-connection-problems

  You probably need to recharge the device drivers and camera control software (usually included
  with the drivers and installed at the same time).

  Login as an administrator.

  Double-click Control Panel / Device Manager - Imaging - writing down of the brand and model of camera.
  on this subject and on the tab of the driver is version. Now, click on update drivers (who are unable to do anything as MS
  is far behind the pilots of certification). RIGHT click on the camera - UNINSTALL - REBOOT - it
  will update the driver stack.

  Now, go to the system manufacturer's website and download the latest driver for the camera and the other related camera
  software (if not more recent get the same).

  Download - SAVE - go to them and RIGHT CLICK - RUN AS ADMIN - reboot after each driver.

  Manually look at the sites of the manufacturer for drivers.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (update drivers manually using the methods above is preferred
  to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  Then let windows updates on however prevent loading of drivers who are often older than the
  those that you have installed. If updates suggests a pilot and then HIDE it and watch manually to see if their
  really is a more recent version (at the time system manufacturer and the sites of the manufacturer of the device).

  Stop Windows 7 to automatically install device drivers
  http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/

  How to disable automatic driver Installation in Windows 7 / Vista
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/

  Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for professionals,
  Ultimate and Enterprise)
  http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/

  ----------------------------------------------------------------------------

  Check with the Sony Support, their online documentation and drivers (update or reinstall).
  and their forums.

  Sony - Contacts
  http://eSupport.Sony.com/us/Perl/contact-land.pl

  Sony - drivers
  http://eSupport.Sony.com/Perl/select-System.pl

  Sony - Support
  http://eSupport.Sony.com/

  Sony - Forum
  https://Forum.sel.Sony.com/?XID=M:Showcase:eSupport

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Updated intel RAID drivers without losing the RAID 0

  Can I install the latest drivers from "ICH8R/etc/PCH SATA RAID controller" Inter without losing my current RAID.  I know that there is "UPDATE" in drivers... just did during the shutdown/restart installation?

  Hi KenMcC,

  Yes, you can install this update. Hardware updates are not installed automatically. Need to manually install these updates. Updates are correctly configured only when you restart the system after their application.

  Before applying this update, we recommend that you contact the support team of Intel to know the features of this update.
  Visit: http://www.intel.com/p/en_US/support?iid=hdr+support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• need RAID drivers from initial operating system installation

  I need RAID driver for my initial installation of the operating system.

  Hello:

  Just use 7 - Zip and extract the drivers out of the file.

  They will be located in the packages folder once you unzip the executable file.

  Paul

• Portege S100 - reinstall Windows XP using F6 and RAID drivers

  I have this announcement in the hope that it helps someone.

  Well my hard drive is dead, so got a replacement one. I'm not so innocently, I thought that, just down load the drivers from the website of the original dvd.
  So did all of this and the raid has yet to see! Changed the settins to raid in the bios that you get by pressing ESC, then the default values, restart and go back into bios goto page 3 - which is so visible. Make sure that the disc is set to1raid0 - download the manual, but you must agree to any change in typing 1234 when it asks for a string from the manual. Anyway did all that - still no visible drive - so which continues.

  Well apparently there are 2 sets of pilots kr10n and kr10i - that givesyou site is kr10n drivers. That may work for the most recent, but not mine! My laptop needs the kr10i which I can't find on the site tosiba. BUT http://download.cnet.com/raid-drv-20070719134547-zip/3000-18492_4-174094.html or you can google for raid-drv-20070719134547

  The steps for me were so use nlite to add the drivers of kr10i on a WinXP SP3 patched cd and start using that. It was work related.

  After that, everything went great! Well, I didn't have much hair initially, but even less after having finished the process.

  Good luck

  Hello

  Thanks for posting this short statement here in the forum.
  I think it might be useful for some users who try to install Win XP and try to include the RAID drives.

  PS. driver RAID The download also from the European pilot of Toshiba page!
  I installed Win XP and I'm using the nLite tool to include the RAID driver!

• Satellite L30-10 X - need sata\raid drivers for Windows XP

  Need to install the drivers sata\raid for windows XP. Laptops Satellite L30-10 X. Please tell me where I can find it.

  Hello

  Normally, you find that the SATA drivers in display driver package which you can download from the official website of Toshiba... Usually they are placed under the screen driver\SBDrv but I downloaded it and t SATA driver file is :(

  What you can do is download the driver of another model, perhaps Satellite L300D or similar model.

  An alternative you can install Windows XP compatible mode. Go into the BIOS, HDD AHCI mode to the compatible. Then, you don't need a driver.

• Information about the latest drivers for Qosmio E10 / F10 / G10

  Hey all, I don't know if a used Toshiba computer support on the European site of bed this thread, but I hope of course.

  Well it turns out that a little Japanese knowledge so I decided to go to the Toshiba Japan website, in the download section of pilot, and I was a bit shocked ^_^

  For my Qosmio E10, I realized that most of the downloads from the European websites of Toshiba are outdated.

  -There is a new version of the bios 1.70 (which improves stability with Intel chipset AFAIK) instead of on the site of the Euro 1.60. [I didn't try it because my machine is a French]

  -New Nvidia video drivers! 57,82 versus 57,79 on the site of the Euro. [I tried and there are new presets for PC games]

  -New driver tuner TV 1.0.2.6 versus 1.0.2.0 on the site of the Euro.
  [I tried and what a TOTALLY SOLVED MY TV PROBLEMS CHECK, I can finally save all: PAL, SECAM & NTSC without huge flicker that plagued the 1.0.2.0 version]

  -Toshiba offers 'Toshiba Virtual Sound' for owners of the E10 to the Japan. (in Europe, we still have the "Windows Media player SRS WOW" plugin) [I tried and it is a fantastic software, improvement of the sound is great with great presets, you won't believe what you get for your Harman/Kardon after installation of this!]
  It has the great advantage of working for all the Windows programs, not only in WMP as the fact the plugin 'SRS WOW' we have in Europe.

  As you can see there are a lot of new drivers that we, owners of European Qosmio, would really benefit.

  But there's something interesting that you should know about:
  Drivers Toshiba E10 euro site are also outdate compared to other Qosmio models pilots from the Euro site!
  For example:
  -The pilot of his "Soundmax", is a version of 3890 in section E10 and 5160 in the section of the G20!
  It's exactly the same chipset, so it is of course compatible and should also be in the section of the E10.

  -L'Intel LAN driver "INtel PRO 100 VE" is version 7.1 in the section of the E10 and 8.0 in the section of the G20.

  -L' utility development of photo is the version 2.4.0.0 for E10 and 2.7.0.2 for the G20.
  P.E.U. is a key point for Qosmio because he is directly responsible for the quality of image engine Qosmio!)

  I think it's a hassle to go to the other models Qosmio download section to find the latest drivers for our machines.
  Qosmio E10 is a year old and is a fantastic (and expensive ^^) piece of hardware, Toshiba please, update the drivers at the latest as soon as you can.

  It's about the E10, but if you have a F10, G10, I'm sure you can do the same thing as me and go see the download section of the F20, G20, etc... and you will find the latest drivers and downloads for your machine!

  As for now, I really hope that Toshiba would be the BIOS for EURO Qosmio E10 1.70. (For Japanese E10, it is located here: http://dynabook.com/assistpc/download/modify/bsqse102/index_j.htm?qry=.%2F%3Ffunc%3Dpi%26category%3D1310 20% 26keyword % 3Dqosmio % 26cpg %3 D 50% 26session %3 D 027063644820 20051)

  If a moderator of this forum is able to convey this message to the person concerned to Toshiba, it would be extremely useful too ^^

  Thanks for reading.
  Next time!

  Alcahest

  Hello.

  Thanks for this information. It seems that you are passionate about Qosmio :)
  Well, I think that the Japanese unit models differ a bit like a European models also the utilities and drivers. It of strange that the other drivers work correctly but
  I'm sure that if the new driver, tools and utilities are available for European units you will find this on the site of Toshiba Europe.

  Good bye

• Z210: Bad support/problem with recovery of an Z210 system when changing the RAID configuration backup

  My Z210 accompanies stripped Bay RAID-0, which currently consists of 2 x 1 TB HDD where the OS partition. I want to change that in RAID-1 mirror, but as the application of TSRI does no such RAID level migration, I thought I would try another approach.

  As a solution, I'd do a backup using the Windows backup and restore application. Then, I would change the table using the Boot ROM TSRI before restoring the backup to this new array. But obviously backup 1.9 TB in a table of 932GB will not

  So, to make a backup, I firstly disabled 'System Protection' and the file 'Page '. This allowed me to reduce the OS partition to about 50 GB using disk management. Then I re - activate 'System Protection' and the 'Page file' before making the backup and the creation of a system recovery disk. This resulted in a backup of 35 GB that I stocked up on a USB external drive. And now a backup of 35 GB can fit on my reconfigured 932GB RAID - 1 mirror

  As such, I cold booted my system and during the boot process, I pressed CTRL-I to get the State of mind RAID Intel Boot ROM. you, CTRL-I've worked only if I started cold and the HP USB keyboard directly connected the first USB slot at the back of the system. The first USB slot is at the top left when you look at the back with the portrait of the tower. Connect the HP USB keyboard in USB port or in the hub of my Dell monitor does not allow me to access the ROM to Boot Intel RAID!

  HP should really study this fault

  In any case, when I could access the Intel RAID Boot ROM, I deleted the RAID-0 stripped existing and created a new RAID-1 mirror. Obviously, the process is destructive and wipe the BONES of the table but that's what my backup was to

  Then I started on the Windows system recovery disk, plugged the USB external drive and proceeded to recover my system.

  Everything worked as expected with the operating system partition uses about 50 GB. A simple trip to disk management enabled me to extend the volume to occupy the space allocated, as presented by the RAID-1 array. As such, I find myself with about 932 GB partition that appear in the windows disk management tool. After a check disk and reboot (which fixed some minor issues) all seemed well.

  But no, everything was fine

  Well that ROM boot RAID Intel sees that a mirror RAID-1 about 932 GB and the operating system sees a partition about 932 GB, both as expected, demand for Intel RST in windows States the following:

  

  I don't seem to have indication of what type of table, it is, an options to change the name of the table or an option to check the integrity of the array through the TSRI application in windows. If something is screwed

  But after the update for the application of iRST version 10.6.0.1002 Intel (the newest HP of) version 11.2.0.1006 (version Intel got very practice), the question seems to correct itself. Now the RAID, Windows boot ROM and the request of TSRI in Windows all agree that the table is indeed a mirror RAID-1 932 GB.

  

  I don't know what caused the problem, if it's related to something that was wrong with the process that I used, if she is simply resolved by reinstalling driver, or if this is a fix for a known issue that Intel has included in their questions later from the pilot.

  But what I know is that Intel has resolved a number of issues in the version 12.9.0.1001 driver (which is the latest version for the Cougar Point chipsets) compared to the old driver version 10.6.0.1002 HP has on its support page for the Z210.

  And HP seems unwavering in his lack of interest in the Intels 12.9.0.1001 test pilot and then make it available on its support page for what is a product still under warranty

  It is a mediocre service if you ask me...

  Some HP forum administrator or HP support person hide these forums should impose it in the HP management station and get it looked at. The Z210 is still under warranty for some customers and HP needs to pick up the latest drivers available to all suppliers, test them and then release them to their customers via the support page for this product. All the rest is little change us all.

  I was able to resolve the application problem Intel RST by updating to the latest v11.2.0.1006 Intel driver but it has highlighted a few points that HP should address, see linked post above.

  PS: Add this post so I can mark the thread as solved.