LOV mapping with point

Similar Questions

• Integration of Google map with Map Viewer does not work

  Hi team,

  My MapViewer Version: Ver11_1_1_7_B130111

  I created a Google Map (with the Source as "Google Maps" map Type) in the map viewer Oracle and I could see google map in Oracle Map Viewer (using 'show Map').

  I wanted to show a theme of map of the village on the google map above in a web page and I use Jdeveloper to integrate with data from the Village map viewer. I could see that the google maps within Jdeveloper however when I run the code Jdeveloper google map does not appear within the web page.

  I tried with Oracle Maps, Bing Maps as 'source' in the map viewer and tried to integrate within Jdeveloper and achieved the same result (white screen). However, when I tried an another mapviewer (Base map ELOCATION. OracleFMW MapViewer House WORLD_MAP) I could see the map on the web page.

  I could get all the other basic maps (created with "internal" as the source of the map") on the web page, so there is something that I'm missing with Google Maps, Bing Maps, Oracle cards. Could you please help me what I'm missing or point to a resource to help?

  Thank you
  Nag

  You need a newer version of JDev (like 11.1.2.x.x or later).

  Geomap DVT (if that's what you use) includes a local copy of oraclemaps.js.

  This must be a newer version.

• is possible to use either usb 6353 map with Matlab 2010A

  Hello

  On a bought a NIUSB 6353 map, but in my computer don't I i the 2010 version of Matlab. Is there a way to control this version of this map with MATLAB

  Thanks in advance

  Hello

  And thanks for posting here.

  Please write in English if you post here. Otherwise, post on the french forum.

  NI USB-6353 using the DAQmx driver, it must be used with Matlab.

  You will find several links from the NI USB-6353 by clicking here.

  And presents an additional link showing you how to use your device with Matlab: Introduction to NOR-DAQmx with Matlab tools

  Kind regards

• How can I fix defender of windows with pointer not valid error 0 x 80004003

  How windows Defender ifix with pointer not valid error 0 x 80004003

  Hello

  ·           When you get this error message?

  ·           You have security software installed on the computer?

  Step 1: Temporarily disable the security software and check if it makes a difference.

  Disable the anti-virus software: http://windows.microsoft.com/en-SG/windows-vista/Disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

• What type of reporting, we can do on CDO and is it mandatory to have all records in CDO to map with contacts to appear in reports?

  Hello

  What type of reporting, we can do on CDO and is it mandatory to have all records in CDO to map with contacts to appear in reports?

  Any ideas?

  Thanks in advance

  Hello

  It is perhaps not necessary to map contacts but in case you need activity report too, so it must be mapped.

  

  To implement a reporting for the CDO, by clicking here.

  After you click here, you will get an option to add several LCO for reporting. And you can get the report here. After the addition of CDO to report, it takes 10 minutes to reflect changes in insight.

  

• How to create a line with pointed head

  Hello
  In my application, I need to draw the line with pointed head, I don't know how to set a custom with pointed head line.
  
  Is there a solution, please answer.
  
  Thank you

  Hi, add this function after drawing the line

  public function createArrow (): void
  {
  var angle: Number = Math.atan2 (getY2 () - getY1 (), getX2 () - getX1 (());
  graphics.lineTo (getX2 () - arrowHeight * Math.cos (angle) - arrowWidth * Math.sin (angle),)
  getY2 () - arrowHeight * arrowWidth + Math.sin (angle) * Math.cos (angle));
  graphics.lineTo (getX2 (), getY2());
  graphics.lineTo (getX2 () - arrowHeight * arrowWidth + Math.cos (angle) * Math.sin (angle),)
  getY2 () - arrowHeight * Math.sin (angle) - arrowWidth * Math.cos (angle));
  }

  getX1(), getY1(), getx2() and getY2() are the start and finish of the line

  Hope it will work for you.

• Oracle OFA customization list of values (LOV) mapping in Where clause with variables

  Hi all

  I have a requirement to add the condition of the UOM LOV I don't understand under conditions in LOV for example mcc.inventory_item_id =: 1 what: 1 means? and how the system look at the value in: 1? if I have to add the condition to the middle which number should I use?

  SELECT * FROM (SELECT distinct muc.unit_of_measure unit_meas_lookup_code, muc.unit_of_measure_tl unit_meas_lookup_code_tl, muc.description, muc.uom_class, muom.uom_code FROM mtl_uom_conversions_val_v muc, mtl_units_of_measure muom WHERE (muc.uom_class IN (SELECT mcc.to_uom_class CMC mtl_uom_class_conv_val_v WHERE mcc.inventory_item_id =: 1) muc.uom_class = GOLD: 2), AND (muc.item_id =) ((: 3 GOLD muc.item_id = 0) AND muc.unit_of_measure = muom.unit_of_measure) QRSLT WHERE ((UPPER (UNIT_MEAS_LOOKUP_CODE_TL) like UPPER(:4) AND (UNIT_MEAS_LOOKUP_CODE_TL like: 5 OR UNIT_MEAS_LOOKUP_CODE_TL as: 6 OR UNIT_MEAS_LOOKUP_CODE_TL as: 7 OR UNIT_MEAS_LOOKUP_CODE_TL as: 8))) ORDER BY upper (unit_meas_lookup_code)

  

  Concerning

  A.S.

  Hey A.S.,.

  Looking more closely at the image you included, it seems that it is already a custom code, it starts with "Xx".  You should see if you have the available custom code.

  To answer part of your original question ""mcc.inventory_item_id =: 1 what: 1 means? ' " The ': 1 ' is a variable binding in the SQL code.  This value is populated at run time by using the "setWhereClauseParam (Bind number, value).  You can see the details of the request and the variable linking using JDeveloper and a double-tap on the View object.  Again, this should be in the custom code of the object View 'atco.oracle.apps.po.lov.server.XxDocumentUomBothVo '.

  I hope this helps.

  Thank you

  Tim

• Can I create a Google Map with several points?

  I am building a Web site for a company with several companies, and they want all appear on the map. In the standard Google maps widget, you can add only one address. Is it possible to add multiple addresses without scripting?

  You can always add placements more once you have published the site by editing the source code. Otherwise simply don't use the widget and enter the code clean Google according to custom HTML.

  Mylenium

• IOS mixed Crypto Maps with Checkpoint Firewall

  I have a config encryption that works very well with a remote CheckPoint Firewall:

  -------------- \/ CONFIG 1 \/--------------------

  crypto ISAKMP policy 5

  BA 3des

  md5 hash

  preshared authentication

  !

  ISAKMP crypto key address 1.2.3.4 cryptokey1

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac txfrmset1

  !

  crypto dynamic-map vpn Dynamics 10

  Set transform-set txfrmset1

  !

  secure1_in card crypto ipsec isakmp 1

  defined by peer 205.245.184.2

  Set transform-set txfrmset1

  match address 105

  !

  IP nat inside source overload map route sheep interface Ethernet0

  !

  sheep allowed 10 route map

  corresponds to the IP 110

  !

  access-list 105 permit ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255

  ------------/\ CONFIG 1 /\ --------------------

  I need to add a card for remote clients using the Cisco VPN 3.6 client.

  I have a card encryption that has worked great for me in the past. The combination

  Both looks like this:

  ---------------\/ CONFIG 2 \/ --------------------------

  Nine AAA

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  crypto ISAKMP policy 5

  BA 3des

  md5 hash

  preshared authentication

  !

  crypto ISAKMP policy 10

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  !

  cryptokey1 key crypto isakmp address 1.2.3.4 No.-xauth

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac txfrmset1

  !

  crypto dynamic-map vpn Dynamics 10

  Set transform-set txfrmset1

  ISAKMP crypto client configuration group remote1

  cryptokey2 key

  DNS 10.0.0.4

  WINS 10.0.0.5

  VPN-pool

  !

  card crypto client secure1_in of authentication list userathen

  card crypto isakmp authorization list groupauthor secure1_in

  client configuration address card crypto secure1_in answer

  secure1_in map ipsec-isakmp crypto 5

  defined peer 1.2.3.4

  Set transform-set txfrmset1

  match address 105

  vpnclient 10-isakmp ipsec vpn dynamic-dynamic crypto map

  !

  IP VPN-pool pool 172.16.30.1 room 172.16.30.254

  IP nat inside source overload map route sheep interface Ethernet0

  access-list 105 permit ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255

  !

  access-list 110 deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255

  access-list 110 permit ip 192.168.0.0 0.0.0.255 any

  !

  sheep allowed 10 route map

  corresponds to the IP 110

  ---------------/\ CONFIG 2 /\---------------------------

  It's classic crypto right out of the playbook of Cisco. This card works

  very well with the Cisco VPN client, but produced the following errors after a

  successful with Checkpoint Firewall P1 installation:

  --------------\/ ERROR OUTPUT \/ -----------------------

  05:13:02: ISAKMP (0:2): send package to 1.2.3.4 (R) MM_KEY_EXCH

  05:13:02: ISAKMP (0:2): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE

  Former State = new State IKE_R_MM5 = IKE_P1_COMPLETE

  05:13:02: ISAKMP (0:2): need to config/address

  05:13:02: ISAKMP (0:2): need to config/address

  05:13:02: ISAKMP: node set 1502565681 to CONF_ADDR

  05:13:02: ISAKMP (0:2): pool of IP addresses not defined for ISAKMP.

  05:13:02: ISAKMP (0:2): node 1502565681 error suppression FALSE reason «»

  05:13:02: ISAKMP (0:2): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE

  Former State = new State IKE_P1_COMPLETE = IKE_CONFIG_MODE_SET_SENT

  05:13:02: ISAKMP (0:2): 1.2.3.4 received packet (R) CONF_ADDR

  05:13:02: ISAKMP: node set-1848822857 to CONF_ADDR

  05:13:02: ISAKMP (0:2): entry unknown: status = IKE_CONFIG_MODE_SET_SENT, major, minor = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE

  05:13:04: ISAKMP (0:2): 1.2.3.4 received packet (R) CONF_ADDR

  --------------/\ ERROR OUTPUT /\--------------------------

  This does not happen to config 1. If it's a PIX, I would use the

  No.-config-mode keyword after the No.-xauth on isakmp crypto "key."

  command line. It is not available on IOS IPSEC and I have never

  needed to do before. I am running Cisco IOS 12.2 (5.4) T on a VPN of 1721

  router. The static map seems to work by itself. What I am doing wrong?

  I saw her a couple of times and to be honest have never taken down to an exact cause, although in this case it looks like almost to the point of control request an IP address which is weird. Try the following:

  1. Add "card crypto secure1_in client configuration address to initiate" and see what it does.

  2. try 12.2 (8) code T5 with it, I had a previous user running 12.2 (11) T and we got the same error messages, returning to this level of code it is resolved.

  In addition, you wouldn't need:

  > access-list 110 deny ip 192.168.10.0 0.0.0.255 172.16.30.0 0.0.0.255

  for example, so that you do not NAT client VPN traffic?

• How to draw lines on a map with CS4

  I have CS4 and would like to know how to draw lines on a map image. I'm a beginner, so what do I do?

  It's about CS6, but CS4 would be a similar process:

  Here's a way to draw a line:

  

  Select the pen tool.

  

  Make a new layer which will be placed on top of the existing layer in the map.

  

  Draw a line with the pen tool, you can see the points that I made to create curves.

  Here is more information on the pen tool: http://psd.tutsplus.com/tutorials/tools-tips/photoshops-pen-tool-the-comprehensive-guide/

  http://www.Tutorial9.NET/tutorials/Photoshop-tutorials/pen-tool-basics-in-Photoshop/

  

  In Photoshop, you have to go back to the options bar and select "shape". This allows you to place a 'coup' on the path (line) that you just created. Otherwise, it will not be displayed.

  

  You can see the settings in the Option bar above, I did. I made that Fill was placed on 'none', and I chose a color for my race, but also a point of size for the thickness of the line until its visible on my card.

  

  It comes to the final.

  Good luck!

  Janelle

• LOV cascading with null

  Hello
  
  I use APEX 4.0 on 10g.
  
  I have 2 LOV, the second, based on the first.
  One displays null as 'null' % values to display all rows back.
  
  When I select a value from the first LOV (except 'null'), the second is updated with the correct values: it works.
  But when I select the value 'null', the second list is empty, rather than be filled with all the values.
  
  The second LOV based on the first request (P3_FILTRE_AREA_NAME):
  

  select distinct(ACCL_NAME) display_value, ACCL_NAME return_value 
  from POINTS WHERE upper(AREA_NAME) LIKE upper(:P3_FILTRE_AREA_NAME)
  order by 1

  When I run this query as a replacement for Sqlplus: P3_FILTRE_AREA_NAME by '%', it works, it returns all the rows.
  
  Any idea?
  
  Thank you.
  
  Yann.

  Hi Yann,

  You must set * "Optimize Refresh" = No * regarding your second select list P1_ACC_NAME. If you do that it will work.

  I also suggest to change your list of first selection P1_AREA_NAME to

  Display null value: "- show all xxx -" (without the quotes)
  "Return NULL value:" (without the quotes)

  and the declaration of LOV your second selection P1_ACC_NAME list to

  select distinct(VALUE1) display_value, VALUE1 return_value
  from TABLE WHERE upper(VALUE2) LIKE nvl(upper(:P1_AREA_NAME), '%')
  order by 1
  

  I think this makes it more transparent by looking at the SQL statement what happens where nothing has been selected. It is also more pleasant that P1_ACC_NAME is set to null if you need to access this page element in the continuation of the procedure on your page.

  Concerning
  Patrick
  -----------
  My Blog: http://www.inside-oracle-apex.com
  APEX 4.0 Plug-Ins: http://apex.oracle.com/plugins
  Twitter: http://www.twitter.com/patrickwolf

• Satellite A40: keyboard mapping with us Euro WinXP Pro

  I thought it was a simple problem to solve, but unfortunately it has escaped me. I had to reload a Satellite A40 with the American version of WinXP Pro Corp. Laptop was purchased in Germany. The keyboard is physically different than typical laptops, used here (pressing the button gives you a Z, for example). Is it possible to map the keyboard so that the user can get an idea of what is typed? I crossed the region in question, and I had no chance (unless it's just me?!). Any guys help? Thanks a lot :)

  Hello

  As you said in your advertisement you can change the keyboard language settings in the Control Panel regional and language settings language Details tab

  In the installed services, you can add the language of the US or UK keyboard.
  Please note: you can set several languages. To switch between the settings please use the keys ALT + SHIFT.

• I am creating a book with iphoto and to insert a map with the locations, I realized, I could add the card, but not the location when I go in option

  I have created a book with iphoto and that you have inserted a card. I can't add the cities that I visited when I option

  Can someone help me

  Thank you

  What card theme you are using?  And what version of iPhoto?  Your internet connection is working?

  In iPhoto 9.6.1, you can add a location in layout mode.  Zoom in on the map and ctrl - click the location on the map, and then select 'Add Place '.

  In mode 'Options', you should be able to press the button "+" and type a name for the place. The location search pictures by name. You can also ctrl - click on the map and add the location manually.

  What happens when you try to add a place? You get an error message?

• Configure a mapping with txt file in LabVIEW

  Hello world

  I would like to connect my I/O with labVIEW and my .txt file (as in VeriStand) but I can't find any block or VI to do.

  Is there a trick or something like that? My txt file is approximately 300 lines...

  Thank you!

  Nico

  This VI is correct.

  Your problem is related to the names of agencies and models.

  Once you correct this (in the Homeless or TXT), it works fine.

  Check the attached file. Only the LED switches to green when each channel is added to the Homeless, if you have a single channel with the wrong name, he is unable to map all other channels.

• CVI 2013 SP1 - function calls repeated with pointer on a variable array parameter causes a shift of the index

  I have some functions will be pointers as parameter and CVI 2012 SP1, they work as before without problems but with CVI 2013 SP1 they are now incorrect.

  Here the description of what is happening - I found a cure, but a duty adopt the old code and I think it's clear that nobody don't "captures" all lines in a 'big old code' which are affected (maybe):

  I have functions

  'function_XYZ(int *p_paraArr) '.

  with 'p_paraArr' as pointers on a table (int).

  Suppose I have another function

  "fct_TOP (void)".

  where is a local array variable which is inizialized by

  "int TheArray [25] = {0};

  and inside of this "TOP"-function-body I call a function ".

  "function_XYZ (TheArray).

  There are no complains of the compiler (CVI 2012 or 2013) and the code works (but the CVI 2013 only once!).

  But if I put 'fct_TOP' loop I have a lag in the "TheArray' -memory.  (The loop surrounds the function "TOP"! "")

  This means that the result "TheArray" obtained from "function_XYZ (TheArray)" starts at index '1' not on the index '0' - as the first time that the function "function_XYZ (TheArray)" was performed. ".

  The solution is:

  I only replaced

  "function_XYZ (TheArray)" (<1>)

  by

  "function_XYZ (&(TheArray[0]))" (<2>)

  overall the program now works every time (in the whole loop)-the first time (in the loop).

  In the second version (<2>) everything is necessary to "work well":

  The '&' and parentheses "(...)", which contains the element that may be designated by the '& '.

  And I hope that you believe me: I've tested several times, it was only "little" change that solved the problem.

  So it seems that the ICB 2013 (SP1) is a kind of internal offset index by a repeated execution of the

  "function_XYZ (TheArray).

  but I don't know how or why but I see in debug mode by observing the expected against the values in the table received!

  At the first time the (implicit) internal index of 'TheArray' is '0', but the following times (during the execution of the loop) the internal index passes to '1' (seen in the debugger because that all the expected values were shiftet like that!).

  So there's an explicit index in the table ("function_XYZ (&(TheArray[0]))") necessary to make the first time of this clear code execution.

  There are some good improvements in 2013 CVI (SP1) and I like this environment more than the 2012 version - but:

  There are other "changes" also, in the compiler (or linker...?) that are more rigid than "in ancient times.

  The problem of this kind of error is always the 'old code '!

  It is expected of such behavior.

  The compiler/linker do not complain (a complaint would be good!) writing but he made this mistake (in a loop).

  By the way: my 'compilation Options' are set to 'Extended' (without change in the "..." ("- button - Options) and that all of the boxes, except the" OpenMP_support "-box are checked!"» So I think that I put the very rigid compiler - maybe there are some «...» ' - button - settings to get rid of this problem, but I have not found them/it.

  My request:

  -Check the stiffer compiler by the need of an explicit index

  - or switch to the 'old' behavior with "function_XYZ (TheArray)" always refers to implicit index '0' of the element "TheArray". "."

  Thank you for your messages, comments and suggestions.

  -As I wrote before - maybe it's the style of programming or error"self made"... maybe...
  .. But if I replace 'function_XYZ (TheArray)' by "function_XYZ (&(TheArray[0]))" and
  then it works... Why so and not, if bothe the same? ...

  But as long as I do not post sample code, nobody is going to accept - I accept it. So consider this post more as an allusion to the fact that of the LW/CVI 2012-2013 LW/CVI more changed than just the LW - GUI or certain features: the compiler changed its 'way to'... or almost.

  For this problem, I think that I will use the solution 'use no implicit and explicit pointers'.
  Who should be a good idea taking into account
      http://forums.NI.com/T5/LabWindows-CVI/fatal-run-time-error-dereference-of-out-of-bounds-pointer/TD-...

  mybe also only caused by wrong code... who knows... but for me it is a sufficient reason to act as I suggest above.

  Best regards,
  F.