Low signal coverage

Similar Questions

• 40VL733G - new Firmware - always 'low signal intensity' is displayed

  Model: G 40733
  Firmware: 10.1.59.6

  Hello!

  After installing the new Firmware the TV always shows 'low signal intensity', but the quality is good, nothing has changed.
  What can I do?
  Everyone has the older Firmware?

  You reset the TV after the update of the firmware?
  In the contrary case that

  Resetting must be done always after the firmware has been updated.

• Low signal Amplitude on PXI-4461

  I currently use two PXI to generate an analog signal through LabVIEW 2009 to an oscilloscope:

  

  PXI-4461 runs below the attachment (properly labeled).  It also produces the green line on the graph.  It seems OK on the oscilloscope.

  PXI-5412 runs the other (properly labeled) attachment below.  It produces the yellow line on the graph.  This amplitude is measured properly (or so it shows in the margin of the image), however it gives me a warning of "Low Amplitude of the Signal" and displays the wave that is much smaller than the "correct" version of the 4461.

  * Note: I guess it's possible that the PXI-4461 (green) is false and the PXI-5412 (yellow) is right, but as the PXI-5412 (yellow) produces the error, I am led to believe that this is the problem.

  I could use help to find out what could be causing this inconsistency and how I could do to fix this problem.

  This has nothing to do with LabVIEW.  This is the oscilloscope all partners.  The reason why the yellow signal is smaller than green is because your ranges are different.  Look at the bottom of your oscilloscpe: Ch2 said "500mV by division" while channel 3 said "1V by division.  You probably get a "low signal amplitude" because you report is less than '2 divisions' and offer thus the scope allows you to change this.  There is a button named "Autoscale" your bezel that you can hit if you want.

• Acer aspire v 15 nitro VN7 - 591 G-74LK wifi problem low signal...

  Please help me how to fix wifi

  My laptop: Acer aspire v 15 black nitro Edition VN7 - 591 G-74LK

  During my weak signal wifi, delays in waiting, slow speeds, disassembly of connection, etc.

  Please how to fix.

  I installed patch full
  And my version of the 10.0.0.299 wireless driver

  The very low signal strength...

• Computer "is" more low-signal router instead of range extender

  I've seen a few similar posts; but nothing seems exactly like my problem; or I missed it.

  I have a router WRT54G and WRE54G range extender; seem to be working well and talk to each other.  (Took a while, but I got it; and it has been fine since.)   I connected to the signal stronger WRE fast when Internet and slow Internet when WRT connected to the lower signal (which is further) - just like one would expect.

  The problem: my computer (only place Office) will be unrelated to the stronger signal "Range Extender".  I'll work some time or leave and come back - and the link will be back signal Extender, fast router signal slow, lower.  I can click on my profile; Connect and sometimes come back on the most powerful signal.  (If not, try again and again until it crashes into the most powerful signal.)  [Even with "site survey" - I select Connect to the stronger signal, but it seems to connect randomly either.]

  - & - Another post, I think I could do something with the MAC addresses - for example, block my USB MAC of the router wireless receiver, so he 'only' to connect to the Extender.  (Better yet, I can say my network connection to connect only to the MAC of the extender?)

  Operating system is - 2000

  Here's something I put in place earlier - for the most part just repeats above:

  Equipment:

  LinkSys wireless router; WRT54G; 6 worm.  Firmware 1.00.7 (now 1.02.7)

  LinkSys Range Extenders;  WRE54G; Firmware Ver 3 3.01.01 (now 3.04.01.)

  USB LinkSys network adapter: WUSB54G Ver 4

  -WHY it keep coming back to the lowest signal from router?  (The big question).

  -Why, when I do a site survey, select the strongest signal and select Connect, enter the WEP code, he still occasionally connect back right at the lowest signal from router, even if I've highlighted the stronger signal Repeater when I hit the Connect button?

  -If I create profiles with the most powerful signal, it is always the same (that is, sometimes it connects the signal the most powerful signal "Extender" and sometimes the Repeater weaker signal, except that I do not need to enter the WEP code if I connect to the profile instead of the signal of view survey.)

  -According to information online, I found that the router must be on 'Firmware version 2.02.2' to be compatible WRE;   But - if I check for the latest version of the firmware for WRT54G version 6, it is 1.02.7 - does that mean the Extender is incompatible with my router?

  -Are there a way to "force" the wireless network connection to bind to a specific MAC address - so I can restrict to a stronger signal of the Extender?

  Scrooge, thanks for the suggestions.    Earlier, I tried the following solution, based on a similar condition a few - this on another post:

  Solution: Configure the router MAC filtering does not to allow connections to the MAC address of the wireless USB network card.

  Since I tried this a few days ago I was followed and it worked.  So, before he would keep switching to the smaller Repeater link.  In saying the Repeater from the heat to let the link not only the Extender to post a link and it is now to stay connected to the Extender and the speed remains constant.

• Low signal strength, high-end hardware

  My old adapter dead netgear recently. It has just stopped working. It worked fine until now, if a little slow, but he never gave me peaks of lag or sudden failures. I got a new Linksys adapter and went with the G because my old netgear adapter is a G. I noticed the signal strength is low, and when I played games online I was sometimes a hint of lag. I decided it might be time to update my router as well. So, I bought a N of Linksys wireless router. No change, still a power low signal and occasional spikes of lag. So I traded my linksys for Linksys Wireless-N router adapter. Higher speeds, but always a low signal strength. My router is down hard connected to a cable modem. That's about 30 feet of the card, with a couple of walls between the two. Should there be any reason why will not improve my signal strength, and I continue to experience spikes obstructive gal? I'd switch Netgear, because I never had this problem before trying to Linksys? Some advice, please.

  Not even a Word. Thanks for making my decision, Linksys.

  (Mod Note: under the direction of compliance from the forums.)

• My computer tells me that I have a wireless router low signal

  Wireless connection

  My computer tells me that I have a wireless router low signal. This problem just started

  Hello

  Also all the list SpiritX MS disorders possible tyre also connect to the menus of wireless router (read the router for how-to manaul) and change the transmission channel.

  Try all of them (11) and choose the one that gives the best results.

• Wirless network on Tecra M6 low signal

  Recently, I bought a Tecra M6. It's a good sturdy laptop but I noticed that wirless receives a signal is lower than about other Toshiba laptop such as Satellite 15 ", being very close to your WiFi access point to connect convinet wirlissly

  I put t know what card you have on the Tecra M6, but maybe this isn't the same type on the laptop Satellite.
  In addition, there are different WLan standards: A, G, B, etc.
  Each standard supports of different properties. Also different WLan cards are more compatible with the router like other wireless network cards.

  But, perhaps it is only a matter of setting WLan.
  You can try to enter the WLan card properties in Device Manager. In the properties, you should find the tab to advantage. There are different options like signal strength or the energy saving mode. You can try to change some settings, for example to disable the power saving mode.

  In addition, you can try to check if there is an update of the WLan drive. You can visit the manufacture of cars of WLan and pilot the site of Toshiba.

  But if it doesn't help then I guess there's not much to do.

• Capture network in areas of low signal Signal

  Dear motorcycle team,

  First of all a big thank you to the motorcycle team together to provide a beautiful and excellent mobile phone at a competitive price in the Indian market. Moto X Play Rulez...

  Come back my mobile 2 days. One thing I noticed in my last 2 days of use is signal capture is not as good as it should be. If I go to low or no signal box and then come back to an area where I get signal, unless the signal is very good bike X play shows emergency call message. I have to manually go into the Mobile network settings and choose the operator network options and sign up automatically for the return signal. I've been using Moto E 1 St gen is the same area, but has not been faced with this question... Maybe something with the 5.1.1 build bike x play...

  Only if the signal is top notch is the high efficiency of the range, it must be done manually and the signal falls also intermittently.

  Any thoughts... Everyone in the face of these questions...

  
  

• The low signal strength WET610N

  My WET610N is on a 5 GHz wireless network and is located about 30 feet from my router (Netgear C3700) with a line of direct sight.  The 5 GHz network uses channel 11 operation up to 145Mbs.  The WET610N shows a signal strength of 28%.  My laptop wireless, running "WiFi channel Scanner" is positioned near the WET610N and shows the signal strength 85% on the same 5 GHz network.

  A Speedtest.net test on the laptop computer watch ~ 60Mbs speeds on a connection from Time Warner ISP download 100Mbs.  The WET610N, running the same test of Speedtest.net shows only the 5Gbs of download speeds.

  The intensity of the signal would be the cause for the lower results of speedtest?  Wireless Setup is not that many configuration options.  Which parameters can affect the intensity of the WET610N signal?

  BTW, I tried the same tests on the network wireless 2.4 GHz, with similar results.

  OK, I just made a major discovery, but I'm still not sure on how to correct what I discovered.

  On a whim, I unplugged my desktop computer, which is a system 8.1 of Windows, the WET610N and plugged my laptop, which is still under Windows 7.  When I ran the test, Speedtest.net, my laptop registered 97Mbps download speeds!

  Thus, it seems that the WET610N works beautifully and it's something on my desktop does not work properly.  I recently upgraded to the Windows 7 Desktop to Windows 8.1, and I remember very well that the network provided quickly enough before the upgrade.  Maybe it's the network on Windows 8.1 driver.

  Anyway, I guess I should mark this issue as resolved, since this is obviously not a problem with the WET610N.  If anyone has any advice about network speed using Windows 8.1, your answer would be approciated.

• Latitude C640 with 1470 mini pci wifi has very low signal strength

  I just installed 1470 broadcom mini pci card with the 4.10.40.0 (from decompression R115321.exe) on a Dell Latitude C640 driver version.

  The card sees the network and connects, but I must be withinn 5 feet from the router, and even in this case the signal is 'Very low' (an or maybe 2 bars). I can communicate with various other wireless cards on other laptops with the full signal strength during the major part of the House.

  Why the intensity of the signal would be so bad?

  Is the 1470 is not very sensitive? the driver is bad for my setup? is there an INCOMPATIBILITY between the 1470 and the DLink DI-524 router? Is this an indication that the antenna on my wifi card is damaged? (I got it on ebay)

  Any help would be greatly appreciated.

  Thank you.

  Latitude C640

  Windows XP SP3

  Wireless 1470 mini pci card

  connected to the Dlink-524 (firmware 1.11) wireless router using WPA - PSK encryption

  
  

• NB200 w/Atheros AR9285 - extremely low signal wireless

  I have bo9ught a laptop computer mini nb200 with Windows XP SP3 a year ago and I've always had a very weak signal (1 bar) wireless, but I blamed the router, I had. But recently I changed my router (EDIMAX BR-6204Wg) and a friend brought another laptop at home and the diference between the signal we had was amazing. while I was trying to conect to my router, it might even catch a signal public wireless to a park four blocks from here.
  I'm grateful for the help.

  PS: Sorry for my English.

  Hello

  How about WLan driver update?
  Here's the latest drivers:
  http://APS2.toshiba-tro.de/WLAN/

  How about deactivation for the WLan to save energy?
  You can do it in the operating system power management and the properties of card Wlan (-Wlan card-> properties > Device Manager)

• The low signal strength with Ralink RT5390 on HP Dv6

  I have two other laptops HP which connect to my wireless router, both have a signal strength 3-4 bar using Intel 5100 and 5300 AGN wireless cards.

  My dv6-6145dx has a Ralink RT5390 and gets only 2-3 bars, but mostly just 2.  I use the laptop in the same place as the others and even tried to move get a signal louder, but nothing has worked.

  I googled and it seems that the RT5390 had some problems like this.  I'm now thinking that maybe I should buy a wireless card replacement.  Intel made half wireless pci-e cards, but I have no idea if they are supported. Should I get the Atheros?

  EDIT: for anyone suffering from slow response of Ralink RT5390 in their computer HP laptop, definitely try the latest pack of driver software from the HP Business Center.  I installed it on my computer and it has greatly improved responsiveness.  It is still not a great card, but at least I'm able to use it now without feeling like I'm on a dial-up connection!

  "If you keep an open mind, life will give you more opportunities."

  Hello:

  Have you tried the latest version of the Ralink driver (5.0.15.0 - March 26, 2013) for your current card?

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-116957-1

  I no longer provide recommendations for WLAN card replacements unless I know a particular card will work in a specific model specifications, that I do not have any warranty information for your.

• 5s battery drain due to low signal

  My battery was in charge when I went to bed and died at 100% this morning as 0 zero!  60% of the use of the battery was weak signal.  I have a connection problem with this phone to the ATT network.  My other 4 iPhones work very well so it is not the location.  I mainly use wifi my phone runs also at work.  I learned that I can turn the phone a replacement, but I only have 10 days left on the warranty.  Is this the only solution?  Is there another way to solve this problem?

  So that it is still covered by warranty, Apple or an Apple authorized Service Provider check the phone.

  Find an Apple authorized service provider

  Apple iPhone - contact Support - support

  To make sure that it is not software related, set it back to factory settings, without using any data backup later. Set up the rest of the personal settings manually and test the phone.

  If the phone works as usual, restore from the latest backup. If the problem returns, the data backup contains damaged data, causing your issues.

  If it still does not respond, it is a hardware problem and the phone must be repaired by Apple or an Apple authorized service provider:

  Use iTunes to restore your device to factory settings - Support Apple iOS

• Problem solved (rt3290 of abandonment and low signal Ralink) wireless card

  Dear owners of Hp

  I recently bought a new Hp laptop which included the defective Ra link rt3290 wireless adapter, included sypthoms was frequent dropouts and forces signal flucatuating. The card was on a 5.0.45.0 Version, I tried to update via the driver properties in Device Manager but ended without any result.

  There were more messages by many hp owners on face similar problems with this card, I tried all possible solutions, including, by checking the box, other wlan adapters, go back to the previous version of the energy-saving stop disabling driver.

  I think that I ve found a solution via a simple update here

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_149767_1#tab-history

  Download version 5.0.53.0 Rev D and when said when a previous version of the driver were found after installation, click on the replacement of all previous features. The update has now fixed the problem and my wifi signal is strong and did not have a single drop out.

  I hope that I have provided some form of assistance, some feedback would be nice, thanks.

  Hello:

  Happy is he who solves the problem for you.

  There is a newer version if you want to give that a try (5.0.56.0 Rev.D (June 10, 2015)).

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_149767_1

  But as the saying goes... "if it ain't broke, don't fix it."